We have an existing WAN connection from a Cisco 2821 router to Time Warner with a single mode fiber connection using the following SFP:We have a ASR 1001 router configured to replace the 2821 router. When I connect the fiber into the ASR 1001 router the link does not come up. I have used the above SFP without success and the following SFP.I have seen Cisco documentation that only certain SFP modules are compatible with ASR router, but I believe the second SFP I listed is compatible. As a test, I connected my ASR router to a 3750 switch using long haul SFP modules on each end so I know the SFP module works. The only downside to this test is I only had a multi mode patch cable. Are there specific settings on the ASR interface that need to be set to allow this connection?
My company has purchased a second ASA for fail over reasons and I'm needing to attach it to my core router (ASR 1001). Currently I'm running the connection between my ASA and my Core as a /19 ie. ASA-10.10.10.2/19 -- ASR-10.10.10.1/19. I know the 2nd interface on the ASR will need to be on a different network segment then the first connection (10.10.10.1/19). What would be the best way to segment this out with out breaking up my /19?
Run /30 segments for each interface? Use a VLan ?
I don't want to use up my Internet rout able IP's on /30 segments. Attached diagram.
I have decided to buy a new wireless N enabled wireless router after my house was cleaned out by some robbers. After a long investigation I decided on the D-link DIR 655 as it suited my basic needs the best and since I haven't decided on a broadband supplier yet this should sort any and all possibilities no matter what I choose...
After an equal amount of investigation I decided on a HSPA+ USB dongle only to find that the router does not support the network I have purchased it on. It thenalso seems that it doesn't support the E1820 Huawei dongle either... so fine... I go and buy a Huawei D105 tht should technically be able to connect via the WAN port and would act as an internet gateway. Brilliant.
Now I have tried everything.... static IP on the D105 with a static IP setup on the 655. Connects fine... according to the web interface but NO INTERNET. When I connect my laptop directly to the 105 via CAT5 it works beautifully. DHCP on the D105 with the same on the 655. Connecting... Establishing Link (Please Wait...) FOREVER without ever getting an IP on the 655 (according to the web interface again) ... must be the D105 thats faulty so again plug in the laptop and within milliseconds the IP is assigned and Internet is blazing along again.... The D105 is not Wireless N so I cannot use it as my primary AP and only allows 5 simultaneous wireless connections (that is reserved for my cellphones). Why should I anyway?? the DIR655 should work fine....
Even after having taken it to D-link support at huge cost and effort I still don't have a working rig.... Seems the consultant plugged the D105 straight into the LAN on the 655 and then set his laptop to the same static range to get it to work... SURPRISE - I know that works since plugging the laptop straight into the 105 does the same thing.... But this is not what I want... I want my 655 to be the primary DHCP server for my network and control the allowed workstations that are allowed access to the internet with a working gateway. Bridging is apparently also not an option as that option has been removed so I cannot even bridge my main subnet onto the D105's internet sbnet... What am I to do....
If the 655 3G setup supported more than 2 dongles I might hve been able to use that and not spend anouther R600 on the D105, if the WAN port actually worked in either static or DHCP modes with the D105 that also would have solved the problem and lastly if all else fails and there was still bridging I could hack my own setup together to do what I want. Seems like I was wrong in selecting the D-link product.
Then to make matters worse I find another product with double the features online for half the price that integrates the 3G capability into the route and support more than 2 different models. including all the new Huawei dongles....
I have the firmware 2.10NA. In my home we have about 4 laptops and 4 smartphones connecting to this router wirelessly and 3 of the laptops often lose connection for hours. We have tried unplugging the router and plugging it in again and factory reset and also resetting it through the IP address but the connection doesnt come back. Recently it has gone out for about 3 hours now. Also the wireless LED icon on the router constantly blinks is this normal? On the laptops where theres no connection it says limited connectivity. Is it possible that there is too many devices connected to the router or something. or could this be a problem with the laptops and not the router?
I am using a DIR 655 router with a DSL 526B modem/router combo. I always get a message saying "Oops! The page you requested is not available.". The page doesnt load (It sometimes does if I keep refreshing again and again). I read somewhere that it might be because I have to bridge my modem/router with my router
Just replaced my SMC Gateway with a Cisco Home Networking Modem, router doesn't see DCS 930 cameras. Working perfect before. I start the wizard, I plug in camera power, plug in ethernet cable for setup, light is green as requested, searches for camera, comes up "No Cameras found". Called ISP provider to reset modem, still no go. Tried a wireless setup using the "buttons", no go. Reset cameras..
Region : Austria Model : TL-MR3420 Hardware Version : V2 Firmware Version : TL-MR3420_V2_121206 ISP : 3
I am using a MR3420 V2 together with a E398 modem. The connection works well, but I can't do any port forwarding (virtual server). Using another router (Tiny Dovado) with the same E398 modem works flawlessly to forward ports.
Region : Portugal Model : TL-MR3040 Hardware Version : V1 Firmware Version : TL-MR3040_V1_120822 ISP : Optimus Kanguru (LTE) www.kanguru.pt
I have a modem huawei E392u-12 from the service provider optimus kanguru, url..., and i would like to use my usb modem with this router i have. the router identify the modem but does not conect. i have seen that the bin files available are just for vodafone and TMN, what can i do so i dont have to buy another equipment.
Region : Germany Model : TL-MR3040 Hardware Version : V1 Firmware Version : ISP :
Just got TL-MR3040 from amazon, not very happy that it is version 1, they could at least mention it in the description, but whatever...The problem is, i can not make it work with my PC laptop(thinkpad x120e with Windows 7 64 bit). Which means,1 not possible to get into web interface to configure it, and 2 if i configure it with old powerbook (os x 10.4) to share internet from usb stick, i can connect to it's wireless network but it doesn't share internet with my pc laptop,while mac and ipad working perfect...I've try to log in into web interface through the cable, still no luck...Not sure i want to re-install the whole system on my laptop just to see if it will change anything, it works with any other router, and usb sticks...
Region : Others Model : TL-MR3040 Firmware Version: 3.14.4 Build 121017 Rel.62268n
I have purchased TL-MR3040 especial for share my 3G account . I have connect it by ethernet port and made setups and it is in 3g/4g only mode. In system checks my modem indicated as " Identified" the modem is a Huawei E160E . My notebook and tablet connects by wireless connection to TL-MR3040 but the router does not dial ISP number *99# . The led on usb modem continues flashing. the 3G modem works perfectly with my notebook and tablet and I use the same parameters for TL-MR3040 with tablet. But most of the parameters don't exist on setup pages of TL-MR3040 . [code]
Region : India Model : TL-MR3420 Hardware Version : V1 Firmware Version : 3.12.21 Build 120523 Rel.37880n ISP : Reliance
I've just set up a MR3420. It works fine in "WAN only" mode and provides access via our ADSL modem. It also works fine in "3G only" mode and provides access via a Reliance Netconnect+ USB modem (a Huawei E150 I think). I updated the firmware to the latest version in order to get it to work with the USB modem.
The problem I have is that when I set it to "3G preferred" it doesn't seem to connect over 3G. I can see it tries to connect but then fails and then WAN takes over. The connect and disconnect options are greyed out on the 3G page so I am unable to manually get it to retry. I've tried leaving it for a long time but it doesn't seem to connect over 3G ever. I've tried setting 3G to connect on demand and connect automatically but both behave the same.
Region : Finland Model : TL-MR3220 Hardware Version : Not Clear Firmware Version : 3.14.2 Build 120822 rel.577775n ISP : saunalahti
dosen't support my huawei E392 4G modem. if possible would you make bin for this. there is not other modems that you can get for 4G connections from the service provider so it would be nice if there was more compatibility than some old ancient modems. starts to feel like this is been sold as 4G router and dosen't actually support that at all.
I have a TP-Link TL-WN723 USB WiFi adapter attached to my laptop, which runs WinXP Service Pack 3. It successfully detdcts the WiFi provided by my Edimax BR62-04Wg router, but when I try to connect, it cannot obtain an IP address and cannot connect to the network.
- The very same WiFi adapter can connect to other routers without any problem - Any other device can connect to the very same network provided by my router without any problem - Using the WiFi adapter with other computers does not work
Thus, it seems that the problem is somewhere between this specific router and WiFi adapter. Here is an interesting detail though:If I try connecting to my WiFi while a LAN cable from the router is plugged into my computer, the wireless connection establishes too. Even if I later unplug the LAN cable, the wireless connection continues to work. But it won't establish the connection without the cable plugged in.Here's what I've already know/tried:
- Rebooting the PC - Re-installing the WiFi adapter's drivers - All drivers and firmwares are the newest available - Re-starting and reconfiguring the router - Using the Windows client for wireless networking and the client included on the WiFi adapter's CD - Changing the router's connection type to any available option: Access Point, Station Ad-hoc, AP Bridge WDS
None of these had any effect except for one:
- When I changed the router's connection type to Station Ad-hoc, I could connect wirelessly even without the LAN cable plugged in, and I had Internet access. However, in this case, other devices, such as smartphones could not detect the WiFi connection.
Region : UnitedStates Model : TL-WR1043ND Hardware Version : V1 Firmware Version : 3.13.12 Build 120405 Rel.33996n ISP : WR1043ND
The router is not showing my external hard drive in the usb settings. The Hard drive is a seagate 7200rpm 1.5tb. The hard drive works just fine when plugged into my computer. I have tried NTFS and EXFAT. My 2gb usb drive in FAT32 shows up just fine. The external has its own power supply. Is there anything I am missing that would cause it to not work?
I've an ASR1001 with 15.1(2)S code on it connected to out ISP, we've been get some complaints about performance and I'm seeing drop on the output policy. Checking the bandwidth consumption we have plenty spare when drops are occuring, there's 300Mb/s. Details below, any suggestions gratefully received
The policy is to guarantee the following bandwidth: Outbound policy: class 1 => 50% guaranteed class 2 => 8% guaranteed class 3 => 1% guaranteed class 4 => 5% guaranteed class 5 => 1% guaranteed class 6 => 5% guaranteed class => 7% guaranteed class 8 => 7% guaranteed class default => not configured
config :
policy-map priority class 1 priority percent 50 class 2 priority percent 8 class 3 priority percent 1 class 4(code)
i have 1001 ASR which boots up ok but shows a warning "filesystem is not clean" and thereafter the image is validated well, it shows up the following two messages and just goes idle from there. [code]
We are going to purchase ASR 1001 with ipbase, BGP is our basic requirment if we purchase ipbase(SLASR1-IPB) it will support BGP.
ProductDescriptionASR1001Cisco ASR1001 System,Crypto, 4 built-in GE, Dual P/SASR1001-PWR-ACCisco ASR1001 AC Power SupplyCAB-IND-RAPower Cord India, Right AngleSASR1001UK9-32SCisco ASR 1001 IOS XE - ENCRYPTION UNIVERSALSLASR1-IPBCisco ASR 1000 IP BASE LicenseM-ASR1K-1001-4GBCisco ASR1001 4GB DRAM
I just need to start building the configuration of an ASR 1001 but I do not know how gigabitethernet interfaces are named on these routers? Are Gi0/0/X or Gi0/X ??
I am replacing my 2900 Internet router with a ASR 1001. I am really not doing anything to fancy on the configuration just routing traffic from the internal LAN to our ISP connection. With the new ASR 1001 there is a configuration for VRF Definition Mgmt-Intf do I do anything with this? There is also a interface for vrf forwarding. At this point we are just running IPv4. The plan was just to configure the GigabitEthernet interfaces but I wanted to make sure if I should try and configure VRF.
I have an issue with an ASR 1001. The problem occurs with MQC shaping applied to a gigabit interface in the outbound direction. The CIR of the provider we are using is 100Mb/sec, so we are shaping to that value. However when reported traffic levels are about 60Mb/sec, we see a steady increase in output drops. [code]
I have also tried increasing the hold queue, however this does not work with the drops. Increasing the shaping rate to 200Mb/sec gets rid of almost all the drops (not quite all!) but is not what we need. I think that we should see some drops when rates spike above 100mb, however the amount we are seeing seems excessive?
This would be the first time I will be working on NCS for a client. There is completely a new install and I was just doing my reading to get my head around the overall working of the product. I had a small Q in mind which I wanted to ask here, while going the config guide, i could not find the way to add a router to the NCS prime. W have ASR 1001 in use along with switches. I read in some forum that NCS supported routers but couldnt find the way in the config guide unless i am missing somewhere. The NCS version is 1.0
We have problem con EIGRP and two ASR 1001 in High Availability. ASR2 have received all route (100 route) from PE, but in ASR1 doesnt received all route (75 route) from PE or from other ASR02. All PE have all route. The ASR1 when modify or lost some route dont update to the ASA. see diagram.
I have a need to capture traffic on an ASR 1001 subinterface, but what I have found is that the Embedded Packet Capture feature is not supported on this platform. Are there any simple alternatives to capture egress traffic on a subinterface or am I SOL? This is a walk in the park on normal IOS routers...
I'm trying to configure Tacacs on Cisco ASR1001, and the Tacacs server is Cisco ACS v3.3, the ACS won't pass the authentication, complaining bad request from NAS, key mismatch - which I compared millions of times on both ASR and ACS sides. [code]
A customer recently purchased an ASR 1001 under the impression it could replace their old 3662 router and ASA 5505. The ASA is configured for their SmartFilter proxy server (N2H2), and I am having a heck of a time finding any documention on how to configure this. I found the following: To use SmartFilter with Cisco IOS firewall, install the SmartFilter componentsand use the IFP plugin (off-box). To configure the Cisco IOS for SmartFilter,use the Cisco document Firewall N2H2 Support located on the Cisco Web site,[URL]Well, I found the Firewall N2H2 Support document [URL], but the ip inspect command doesn't seem to work on the ASR. Is there any way to make this work or does the ASA have to stay in line?...
i want to apply a QOS for my trafic LAN, in my ASR 1001 , the LAN is connected with ge0/0/0 interface and it configured with the service instance to bridge vlan 1 ( i do that for OTV ) i put service policy in "service instance 1" to marking data with ef31 but i noticed that the class "plateform_datacenter" match the trafic and the ACL associate to this class not mach any trafic trafic !
tha policy-map march trafic for Datacenter : sh policy-map interface gigabitEthernet 0/0/0 service instance 1 GigabitEthernet0/0/0: EFP 1 Service-policy input: MARKING-OTV Class-map: Platforme_DC (match-any)
I have problems to configure CBWFQ on a ethernet sub-interface on a Cisco Router ASR 1001. Then I applied the policy in the physical interface but it should be is in the sub-interface. How can I configure CBWFQ on sub-interface in ASR 1001. (version 3.02).
Error Messages:
CBWFQ: Not supported on subinterfaces and efps
This the final output:
interface GigabitEthernet0/0/0 description Conexion WAN bandwidth 153600 no ip address load-interval 30 no negotiation auto
Is there a loop between 192.168.99.191 and .192 (this are two routers with hsrp .190) or is this normal behavior when using trace route on an asr 1001?
