Region : Austria
Model : TL-MR3420
Hardware Version : V2
Firmware Version : TL-MR3420_V2_121206
ISP : 3
I am using a MR3420 V2 together with a E398 modem. The connection works well, but I can't do any port forwarding (virtual server). Using another router (Tiny Dovado) with the same E398 modem works flawlessly to forward ports.
Edit I've found a work-around. It's on page 2: [URL]
I'm having this really weird issue with my DIR-655 revB. I have some port forwarding rules set up and externally they work fine. However, if I try connecting to my IP address using those same ports from a computer within my LAN, it won't connect.
Externally, I can ping my WAN address and connect through forwarded ports. No problems. Internally, pinging my WAN address apparently works (just now is the first time that's worked for me), however I can't access any of my computers using the WAN IP and port forwarded ports. I can access them by going directly to their hostnames or LAN IPs.
Things I've tried:
-Disabling/enabling firewalls on all computers involved
-Disabling/enabling QoS engine
-Disabling/enabling DNS relay
-Disabling/enabling Advanced DNS
-Adding custom nameservers from Google and Comodo
-Restarting computers
-Clearing DNS cache (I use a dynamic DNS name which works externally but not internally. This gets the correct IP internally and connecting directly to the IP doesn't work either.)
-Modifying the NAT Endpoint Filtering settings
I have an external DSL modem connected to the router using PPPoE if it matters.
The weird part is that it works externally but I've modified all of the values I can think of in the config with no luck. I upgraded to the DIR-655 from a DIR-615 which had all these settings in it and worked fine (until it started acting up which is why I replaced it).
Region : India
Model : TL-MR3420
Hardware Version : V1
Firmware Version : 3.12.21 Build 120523 Rel.37880n
ISP : Reliance
I've just set up a MR3420. It works fine in "WAN only" mode and provides access via our ADSL modem. It also works fine in "3G only" mode and provides access via a Reliance Netconnect+ USB modem (a Huawei E150 I think). I updated the firmware to the latest version in order to get it to work with the USB modem.
The problem I have is that when I set it to "3G preferred" it doesn't seem to connect over 3G. I can see it tries to connect but then fails and then WAN takes over. The connect and disconnect options are greyed out on the 3G page so I am unable to manually get it to retry. I've tried leaving it for a long time but it doesn't seem to connect over 3G ever. I've tried setting 3G to connect on demand and connect automatically but both behave the same.
First off, my router is a D-Link DIR-655, firmware v2.07. I'm trying to port forward port 25565.
My port forward settings are this:
However, when I use this open port checker, it claims that I don't have that port open. It looks like this, without the blurred out parts:
Added note: The way I want to use it is by my IP (xxx.xxx.xxx.154:25565). I have the software installed to do so (I'm using a minecraft server, connecting through minecraft), but I can't enter my IP in the IP address field, it says that it's out of the range of the LAN.
Type: WRVS4400N Wireless-N Gigabit Security Router with VPN.I bought it last week. Its single port forwarding has an issue. I can only use that function for a couple or hours. Then the forwarding does not work. I have to reboot the router to make it available again.
View 1 Replies View RelatedJason9 i'm having the exact same problem as above, don't mean to hijack but I'm using talktalk isp, I have AVG 9.0 and have a static IP and forwarded the required port on the router.
View 19 Replies View RelatedI have a W7 PC 64 bit system and I've been trying to port forward the port 25565 for my Minecraft server. However for some reason (even after port forwarding the right one) people still can't connect. When I check on Open Port Check Tool - Test Port Forwarding on Your Router It still says that the port 25565 is closed!I've even created an Inbound and Outbound rule in the Windows Firewall advanced settings. I use Avira Anti-vir fyi..
View 19 Replies View RelatedI have been trying so hard to get the following ports to work:
5120 - 5300
I have looked up countless guides, and have done everything in them, I have a static IP, I used the gateway to create the port forwarding rule, AND opened the ports on the windows firewall.
Nothing works. The port remains closed, and I can't host games. My modem is an Ambit U10C037
System Specs:
OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit
Processor: Intel Pentium III Xeon processor, x86 Family 6 Model 23 Stepping 6
Processor Count: 2
[Code].....
I have a Netgear WRG614 and a Westell 610015 Modem. I need Port Forwarding. I have tried setting up a static IP then Port Forwarding but it doesn't work. I have tried port forwarding from the modem but it doesn't work. I wanna forward ports "80, 9958, and 5816". The reason is because I am gonna host a game server on my computer.
View 14 Replies View RelatedRegion : New Zealand
Model : TL-MR3420
Hardware Version : V2
Firmware Version :
ISP : Telecom New Zealand
getting the MR3420 but will be using a ZTE 669 Turbo stick as the modem ISP Telecom New Zealand.I did notice that they seem to be supporting the ZTE 668+ which I'm guessing is a vary similar model.
Region : Others
Model : TL-MR3420
Hardware Version : V2
Firmware Version : 3.13.27 Build 121206 Rel.60215n
ISP : Cellcom 3g - Israel
My USB Modem HUAWEI E173 not work as well with TL-MR3420 Its lose Identify every almost 15 minutes , and try to Identify again and some times not successfully until I reboot the unit . then its Identify successfully , after some minutes the problem happen again and again . I think its from the router software issue that it have not the correct driver of the modem .
also , the signal of the wireless not that good like the other routers which I used before .
Region : Italy
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0 Build 120720 Rel.09287
ISP : alice
A couple of weeks ago I have bought a TD-W8961ND in replacement of my old modem/router (of another brand, to upgrade from Wireless G to N). I tried to replicate in the new router something similar to my old setup, so I programmed Virtual Servers (under the NAT menu) with the following rules: NATRules.jpg in an attempt to:
- grant access from "outside" Internet to my web server
- have a Wakeup-On-LAN from "outside" Internet ..etc.. without success. Please note that:
- I have successfully setup a DDNS server to reach my modem router from outside
- as for WOL, I defined my subnet mask as 255.255.255.128
- I have not set any other rule, nor in NAT, nor in routing or other
- I tried also with firewall disabled
- I do my testing by means of a smartphone with wireless disabled and Internet connection via mobile service provider
- Both the above mentioned functions were working with my old modem/router (and still work on LAN), and I have not changed other things (PC setup etc)
I have a Huawei 523a Router at the moment and I'm trying to setup a IP camera.The Router doesnt allow port forwarding, so my question is can I add another Router onto the Huawei router to allow the second one to work my camera
View 10 Replies View RelatedI set up my new E4200 to forward port 7300 to a computer on my LAN. I had this working on my Linksys WRT160N and copied all of the settings so they are identical to those on that router but forwarding does not work. I have tried single port forwarding, multiple port forwarding and even DMZ with the same lack of results.
View 9 Replies View RelatedIPort forwarding simply does not work with this rounter on Comcast. I called comcast to see if they were blocking ports and they insist they ARE NOT.So what can it be? Was on FIOS with their modem/router combo and port forwarding worked like a charm with them.I've tried single port forwarding, port range forwarding, yada.
I am using the correct internal IP address on the machine I want to enable port forwarding on..Latest firmware is installed 1.04 or whatever (just purchased the router and updated during the Cisco Connect install on the 29th). Guess I should go find a cheaper router that actually works...
i have a WRT160N V3 and DMZ or Portforwarding dont work.i tried locally following
WAN_PC-> WAN-PORT -> WRT160N V3 -> LOCAL-PORT -> LOCAL_PC
The WAN_PC has a Static-IP 192.168.1.2, Subnet 255.255.255.0
The WAN-PORT has a Static-IP 192.168.1.1, Subnet 255.255.255.0
ON the WRT160N V3 i configured a DMZ on 192.168.0.100.and Disabled the Firewall.
On the LOCAL_PC (192.168.0.100:8888) is a Apache
So when i type 192.168.1.1:8888 on the WAN_PC i get NOOO Website from the Apache on 192.168.0.100:8888?
I have done this before on this exact model about a month ago, so it's still fresh in my mind on port forwarding. (note, I'm using firmware version: 1.0.00) I am running a windows 7 computer wirelessly using this router.What I do for port forwarding is type in router IP (192.168.2.1) in internet explorer, type in "default" as username and "admin" as password. I click the "applications and gaming" link which brings me to port range forwarding.
I fill in my port info, in this case a mine craft server running on 25565. I set up two of the same ports, different names both at the same port, one running TCP and the other UDP, when it worked previously the "both" option did not work correctly. (I used to have a private network that a buddy of mine set up a while back, and I doubt he remembers what to do and I don't know where the manual is to make a new one, searching the internet sends me spam of people asking questions.)
I read somewhere it may have something to do with DHCP server settings conflicting with my IP. My IPv4 address reads 192.168.2.100, and the DHCP settings says the same.
I am having a NAT issue with my two xboxes. The router is an e1000 v2.1 firmware 2.1.02. One xbox is wired into the router and the other has a wireless adapter. The wireless xbox gets open nat automatically, while the wired one's nat is strict. If i mess with DMZ and turn UPnP off i can get the wired to be open but the wireless one to be strict. Also port forwarding does not seem to work because only one or the other xboxes will get an open NAT. I do have the the correct ports in the port triggering section set to on but that does not seem like it works.
View 5 Replies View RelatedContinued from [URL] which appears to have been closed by a moderator with a reference to Cisco small business website, but the registration there doesn't work, all buttons are inactive etc.
I just need to know what to do with this RV042. I have two modems, a cable and an ADSL. Both are configure correctly, in bridge mode. Both work fine when connected to WAN1, but when connected to WAN2 they never go online (dont' get IP address). The connect lights are on but they never go online.
Firmware Version: 1.3.13.02-tm
Region : Germany
Model : TL-MR3040
Hardware Version : V1
Firmware Version :
ISP :
Just got TL-MR3040 from amazon, not very happy that it is version 1, they could at least mention it in the description, but whatever...The problem is, i can not make it work with my PC laptop(thinkpad x120e with Windows 7 64 bit). Which means,1 not possible to get into web interface to configure it, and 2 if i configure it with old powerbook (os x 10.4) to share internet from usb stick, i can connect to it's wireless network but it doesn't share internet with my pc laptop,while mac and ipad working perfect...I've try to log in into web interface through the cable, still no luck...Not sure i want to re-install the whole system on my laptop just to see if it will change anything, it works with any other router, and usb sticks...
My ISP is centurylink and I have a 660 series modem that is both a modem and a router (no wireless). Also I have a Linksys WRT54G v3 wireless router with Tomato Firmware on it. For whatever reason I can't get the port forwarding to work. Yes, I know I have to forward the ports on both and I have tried using this guideurl...Fowarding.php on the modem, with Tomato Firmware it is super simple to forward.
View 13 Replies View RelatedI'm trying to setup port forwarding to a citrix server but, it seems not to be working.
View 4 Replies View RelatedNone of the port forwarding settings are working at all on my router. I have just a couple very simple settings. One of them is just an IP camera. I input the name, the TCP port, the computer (IP address) and that's it. This works just fine with my other Netgear router, but with this router, NADA. The router has the latest version of the firmware applied. Just applied it. Hardware version B. Firmware version: 2.10NA. If so, then I really need my money back since it is a main function of a router and it should work. Can't return it now, since I bought it several months ago. Never knew port forwarding didn't work because I never needed it until now.
View 6 Replies View RelatedI have DIR-615, connected via ethernet. I enabled port forwarding for Quake 3, using the range of 27660-27980 to account for custom server ports. Set schedule to "always" although also did "never" but it didn't make a difference. I checked the FAQs for frequent resets vis a vis application outbound requests, which recommended disable uPnP and this had no effect. Symptom: when Quake 3 attempts to connect to the Master Server, the router resets all connections, LAN and WLAN. It takes approximately 30 seconds to regain connection to WAN, although LAN does not drop. Also during this time, the world sigil on the router itself turns orange. This is the only time this happens, when trying to play Quake 3. Previous router to this one was Linksys (by Cisco) BEFSR41, in which simply setting up port forwarding for the client IP address allowed connection. I can find no particular reason why the router resets all interfaces when blocking a port, if it is indeed the firewall triggering this.
Other infos:
Model: Wireless N 615, DHCP enabled on both sides
LAN connect: Category5 to 10/100 NIC onboard to Intel 865GBF
Client firewall: none
Client OS: Windows XP Professional SP3
I'm trying to configure port forwarding for FTP but in my case it isn't as simple as i assumed ... i have an actiontec router/modem that serves as incoming internet from my provider (FIOS), which i connected to my own router (dir-825). i mainly configure my network on the dlink and leave the actiontec alone.
[CODE]...
I currently use a D-Link DIR-655 router on a game server I run and I've been having this problem for sometime now. I have the router hooked up to the internet modem, and then my server computer hooked up to the router's first port. I use port forwarding to forward the game ports, as well as my FTP server ports. I have about 80 clients or so logged in at a time on my server.The issue is the following. Our internet connection has an external IP of 67.23.155.123 (this is just an example). My internal IP is 192.168.0.101.When I do "netstat" to see all the clients logged in to the game server on this computer or when I run Wireshark, every client logged in to the server (for this game application) is shown as having an IP of 67.23.155.123 (the server's external IP).On the other hand, for our FileZilla FTP server, if I run Wireshark/netstat, I can actually see the client's external IP (i.e. each individual IP of people logged into the FTP).If I hook up the server directly to the internet modem, this isn't a problem, and I am able to correctly see the IP of each client logged in to the game server individually.
View 12 Replies View RelatedToday i installed an RV180 VPN router as replacement for a netscreen ns-5GT.Exactly the same configuration, everything works, except port forwarding from WAN to a host inside NAT.My ports are open (online port-scanner sees the ports as open), the hosts are accepting connections, but a connection can't be made.Probably a bug in the firmware.
View 30 Replies View RelatedI have the DCS-930L camera. I need to know how to setup port forwarding/triggering on my router, which is a Cisco DDR2200 CL. I understand that in order to use the camera, i need to do this. how to set up NAT.
View 1 Replies View RelatedWould a Linksys USB300M Network Adapter allow my computer to connect to the internet via Ethernet? My computer has an Ethernet port that doesn't work. I need Ethernet connection to connect to the internet through FIOS. I currently use an USB port on my computer to connect using DSL. I want to purchase a USB-Ethernet adapter that plugs into my USB port but has an Ethernet jack at the other end: USB300M Network adapter - Hi-Speed USB
View 5 Replies View RelatedI have a problem configuring port forwarding to 443 and having client VPN to work.When 443 is NOT forwarded, VPN just runs fine (QuickVPN).As soon as I enable 443, the VPN stops working. No client can connect.I have the latest 1.2.0.9 firmware.Is there a way to enable 443 and having VPN to work at the same time ? I need 443 for Exchange.
View 4 Replies View RelatedI am trying to set up a custom service on my netgear configuration page. I have a netgear router model# Wnr834m. every time i click the "add custom service" button the page redirects to "system authentication failed" and logs me out. What can i do to set up the new port?
View 1 Replies View RelatedRegion : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP : Virgin Media
Is there any way of forwarding an external port to a different internal port on the TD-8970 ?I saw a question posed on an Australian forum implying that it might be provided in a later firmware release.Our TD- 8970 has replaced a previous NetGear WAG 320N which had this facility, and is useful to provide access to multiple machines without having to modify each individually to use a different port.
I am having an issue opening a port (4040) on the 655 for my Fedora-based subsonic server. Inside the LAN, I can see the device from other peer machines, so I am confident the port is open and listening. However, I can't seem to get to the machine-port from outside/internet.
I have tried Virtual Server and Port Forwarding with single port. The server has a stactic IP which I've included in the DHCP range and outside the range. I have a DSL connection (AT&T), modem only. I have updated firmware. I have exhausted the Subsonic community's knowledge, everything points to the router, but all the settings seem correct. What am I missing? Is if possible there is a defect in the router? (don't laugh). Is there a way to trace a request to that port to see where it is hanging?
(yes, I've STFA, but don't know what else to do).