Linksys Wireless Router :: E2500 Port Forwarding Does Not Work

Apr 2, 2012

IPort forwarding simply does not work with this rounter on Comcast. I called comcast to see if they were blocking ports and they insist they ARE NOT.So what can it be? Was on FIOS with their modem/router combo and port forwarding worked like a charm with them.I've tried single port forwarding, port range forwarding, yada.
 
I am using the correct internal IP address on the machine I want to enable port forwarding on..Latest firmware is installed 1.04 or whatever (just purchased the router and updated during the Cisco Connect install on the 29th). Guess I should go find a cheaper router that actually works...

View 7 Replies


ADVERTISEMENT

Linksys Wireless Router :: Port Forwarding On E2500

Jan 19, 2012

I've read over the FAQ and followed the normal instructions for port forwarding, but can't seem to get it to work with this particular router, E2500.  I have tried both the single port forwarding and the multi port range forwarding, and neither works.  I've tried an older WRT54G router and port forwarding works fine on it, so I know it's not my ISP.I'm running the latest firmware provided by Linksys/Cisco. 

View 1 Replies View Related

Linksys Wireless Router :: E2500 - Set Up Port Forwarding For PS3?

Jan 28, 2012

I recently got a e2500 router and set up the port forwarding for my ps3. But then i go to check the ports to see if they are open and they all stay closed.I have no clue whats wrong as I have entered the port forwarding info correctly as I got guideline from portforward.com but still no luck

View 2 Replies View Related

Linksys Wireless Router :: Port Forwarding Not Working On E2500

Dec 12, 2011

I've read over the FAQ and followed the normal instructions for port forwarding, but can't seem to get it to work with this particular router, E2500.  I have tried both the single port forwarding and the multi port range forwarding, and neither works.  I've tried an older WRT54G router and port forwarding works fine on it, so I know it's not my ISP.

View 4 Replies View Related

Linksys Wireless Router :: E2500 - Forwarding Port To See Camera Over Internet?

Feb 15, 2012

I am trying to forward a port to see a camera over the internet.  On the single port forwarding screen under Gaming, I have put in port 8090 (Ext and Int),Protocal both, an IP address and Enabled.  I have also tried putting in a range, but neither seems to work.   After forwarding the port, I check with What's My IP Addrewss to get the external IP, then put the IP in a blank browser page with and without the port number.  I have tried this several times without any result.  

View 9 Replies View Related

Linksys Wireless Router :: Port Forwarding In A Routed Private Network With E2500?

Jan 7, 2012

I would replace an old Levelone Router with a Linksys E2500.I have 3 different routed private networks (e.g. 192.168.1.0/24 , 192.168.101.0/24 and 10.0.0.0/24) How can I forward different ports to this 3 different private networks with an E2500.Under "Games&Applications" in the" Portforwarding" menu the first 3 octets of the "to IP-address" are fix and corresponds ever with the LAN ip address of th E2500.

View 4 Replies View Related

Linksys Wireless Router :: Port Forwarding For Video Streaming Server On E2500?

Feb 4, 2013

So I am trying to forward a port on my linksys E2500 router. I need to forward 198.162.17.3 for a video streaming server.  When I go to the admin panel I am only able to change the last digit, ie 198.162.1.x   

View 5 Replies View Related

Linksys Wireless Router :: Port Forwarding On E2500 - Cannot View Cameras Remotely?

Jan 19, 2012

I purchased some cameras for my building. I have them set up ok on port 85 but I can't view them remotely until I set up the router to forward the port. I have a charter modem and the E2500 router.

View 1 Replies View Related

Linksys Wireless Router :: E4200 Port Forwarding Does Not Work?

Aug 18, 2012

I set up my new E4200 to forward port 7300 to a computer on my LAN.  I had this working on my Linksys WRT160N and copied all of the settings so they are identical to those on that router but forwarding does not work.  I have tried single port forwarding, multiple port forwarding and even DMZ with the same lack of results.

View 9 Replies View Related

Linksys Wireless Router :: WRT160N V3 DMZ And Port-Forwarding Don't Work

Oct 19, 2012

i have a WRT160N V3 and DMZ or Portforwarding dont work.i tried locally following
 
WAN_PC-> WAN-PORT -> WRT160N V3 -> LOCAL-PORT -> LOCAL_PC
 The WAN_PC has a Static-IP 192.168.1.2, Subnet 255.255.255.0
The WAN-PORT has a Static-IP 192.168.1.1, Subnet 255.255.255.0
ON the WRT160N V3 i configured a DMZ on 192.168.0.100.and Disabled the Firewall.
On the LOCAL_PC (192.168.0.100:8888) is a Apache
 
So when i type 192.168.1.1:8888 on the WAN_PC i get NOOO Website from the Apache on 192.168.0.100:8888?

View 2 Replies View Related

Linksys Wireless Router :: WRT54G2 - Port Forwarding / TCP And UDP Did Not Work Correctly

Jun 30, 2012

I have done this before on this exact model about a month ago, so it's still fresh in my mind on port forwarding. (note, I'm using firmware version: 1.0.00) I am running a windows 7 computer wirelessly using this router.What I do for port forwarding is type in router IP (192.168.2.1) in internet explorer, type in "default" as username and "admin" as password. I click the "applications and gaming" link which brings me to port range forwarding.

I fill in my port info, in this case a mine craft server running on 25565. I set up two of the same ports, different names both at the same port, one running TCP and the other UDP, when it worked previously the "both" option did not work correctly. (I used to have a private network that a buddy of mine set up a while back, and I doubt he remembers what to do and I don't know where the manual is to make a new one, searching the internet sends me spam of people asking questions.)

I read somewhere it may have something to do with DHCP server settings conflicting with my IP. My IPv4 address reads 192.168.2.100, and the DHCP settings says the same.

View 1 Replies View Related

Linksys Wireless Router :: WRVS4400N Single Port Forwarding Doesn't Work

Jul 1, 2012

Type: WRVS4400N Wireless-N Gigabit Security Router with VPN.I bought it last week. Its single port forwarding has an issue. I can only use that function for a couple or hours. Then the forwarding does not work. I have to reboot the router to make it available again. 

View 1 Replies View Related

Linksys Wireless Router :: E1000 / Port Forwarding Does Not Work Because Only One Or Other Xboxes Will Get Open NAT

Nov 14, 2011

I am having a NAT issue with my two xboxes. The router is an e1000 v2.1 firmware 2.1.02. One xbox is wired into the router and the other has a wireless adapter. The wireless xbox gets open nat automatically, while the wired one's nat is strict. If i mess with DMZ and turn UPnP off i can get the wired to be open but the wireless one to be strict. Also port forwarding does not seem to work because only one or the other xboxes will get an open NAT. I do have the the correct ports in the port triggering section set to on but that does not seem like it works.

View 5 Replies View Related

Cisco Routers :: Port Forwarding In Routed Private Network With Linksys E2500

Jan 5, 2012

I would replace an old Levelone Router with a Linksys E2500.I have 3 different routed private networks (e.g. 192.168.1.0/24 , 192.168.101.0/24 and 10.0. 0.0/24)How can I forward different ports to this 3 different private networks with an E2500.In the "Games&Applications" Menu are the first 3 octets of the "to IP-address" are fix and corresponds with the LAN ip address.

View 3 Replies View Related

Linksys Wireless Router :: E2500 Doesn't Work With Two Computers?

Aug 1, 2012

I have a mac 10.7.4 and an xbox 360 slim. Whenever  I try to play online like cod or fifa and someone else is on the computer It is super lagy, Laging. Before when I had a **bleep**y netgear 33 mb it worked perfectly fine. Now this router is has 300 +mb and it stil doesnt work. This router cost me $80 dollars. Before cisco linsys I bought a netgear not the **bleep**ty neatgear but a newer one and it still had the same problem.

View 1 Replies View Related

TP-Link 3G/3.75G Router :: MR3420 - Port Forwarding Doesn't Work

Jan 24, 2013

Region : Austria
Model : TL-MR3420
Hardware Version : V2
Firmware Version : TL-MR3420_V2_121206
ISP : 3

I am using a MR3420 V2 together with a E398 modem. The connection works well, but I can't do any port forwarding (virtual server). Using another router (Tiny Dovado) with the same E398 modem works flawlessly to forward ports.

View 14 Replies View Related

Linksys Wireless Router :: E2500 Web Interface Doesn't Work In Bridge Mode

Jan 10, 2012

I recently bought a Cisco E2500 for work, and after setting the router to Bridge Mode, I am unable to access the router web interface.  I tried both the old IP address (192.168.1.1) and the IP address that I entered when I was configuring Bridge mode, but I couldn't get either to work.  I have always tried resetting the switch to factory defaults and trying again to make sure I didn't type anything wrong, but to no avail.  The wireless and everything works as it should, I just can't get back into the router to change any of my settings.

View 4 Replies View Related

Linksys Wireless Router :: E2500 - Blank Username And Admin In Password Doesn't Work

Feb 23, 2013

Blank user name and admin in password doesn't work.  How to reset these ?

View 1 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8961ND - Port Forwarding Does Not Work?

Mar 10, 2013

Region : Italy
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0 Build 120720 Rel.09287
ISP : alice

A couple of weeks ago I have bought a TD-W8961ND in replacement of my old modem/router (of another brand, to upgrade from Wireless G to N). I tried to replicate in the new router something similar to my old setup, so I programmed Virtual Servers (under the NAT menu) with the following rules: NATRules.jpg in an attempt to:

- grant access from "outside" Internet to my web server

- have a Wakeup-On-LAN from "outside" Internet ..etc.. without success. Please note that:

- I have successfully setup a DDNS server to reach my modem router from outside

- as for WOL, I defined my subnet mask as 255.255.255.128

- I have not set any other rule, nor in NAT, nor in routing or other

- I tried also with firewall disabled

- I do my testing by means of a smartphone with wireless disabled and Internet connection via mobile service provider

- Both the above mentioned functions were working with my old modem/router (and still work on LAN), and I have not changed other things (PC setup etc)

View 14 Replies View Related

Linksys Wireless Router :: E2500 Will Not Allow Port 80 Access

Apr 21, 2012

I bought a new e2500 and it is working fine, all but port forwarding.  This is not even close to my first router and I am advanced when it comes to setting these up.  I have tried for days to get port 80 to open up and it refuses. Now I do notice that when you access the router setup through a web interface, it uses port 80.  I have forwarded port 80 to the ip address of the device, put in a reservation in DHCP with MAC address, etc. etc. and still nothing.  Heck, I have even turned that specific device IP into a DMZ, and it STILL will not work.For the record, I had an e2000 set up the exact same way and it worked just fine and I was able to access port 80.

View 6 Replies View Related

Linksys Wireless Router :: New E2500 Port Light For Wifi Printer Not On?

Aug 18, 2011

I have just upgraded my Linksys router from an older one to the E-2500 about a week ago.  Everything is working great on my wired desktop and 3 wireless laptops except the printer will no longer work from any of the computers.  I've checked the printer wireless settings and they are correct (ssid and password) and it says it's connected to the wlan.  Each of the computers shows the printer is active and set to default BUT the port light on the back of the new router is not on. I have changed cables and still no light, the printer is set up for sharing and it did work a couple days ago but port light was on then.

I have not added anything that wasn't hooked up on my old router, I"m just trying to get what I had on the old router to work on the new one. Everytime I call support, they have me change something that messes up what a previous agent had me do. Now they want me to pay for a direct connection so they can upgrade my router firmware...they didn't even ask what version I already had which happen to be the same version that is available on [URL] so if I had agreed, I would have paid for nothing. I had already paid $29.99 for additional 14 day support on my old router only to find out I needed a new one.

I've been using Linksys routers for quite awhile but I'm just about ready to change brands. I would really like to give this E-2500 a chance.

View 1 Replies View Related

Linksys Wireless Router :: How To Set Port In E2500 To Make Web Traffic To 192.168.1.1281

Jul 6, 2011

My home web hosting used to work. But because of changing ISP from Verizon to TWC, TWC gave me a modem-router and I bought my own Linksys E2500 router. Both Verizon and TWC services I subscribed are Dynamic IP. I use a third party to redirect the web traffic to my home.TWC gave me a simple modem-router in a box. Input is coax and outputs are 4 ethernet ports. I use one of the 4 ethernet outputs of the TWC box to connect to the internet ethernet input port of the E2500. All my wire and wireless devices are now feeding off the E2500. All wireless and wired devices work and can browse internet through the E2500.I have assigned one computer as the web server and set the internal IP addess of this computer as 192.168.1.128. This is the same for the setup with Verizon before.I loaded the CD came with the E2500 router and can see the LAN 192.168.1.128.My problem starts from here, I do not know how to set the port in E2500 to make the web traffic to 192.168.1.1281. Using the E2500 CD, I click to "APPLICATION AND GAMING", then "SINGLE PORT FORWARDING". under the APPLICATION NAME, I select one of the box to HTTP and type in 128 under "TO IP ADDRESS". I then click ENABLED, then "save settings" . The 192.168.1 is fixed in this window, I can only type 128.This does not work. I can browse internet but cannot access my website from any machines using domain name.Then I tried:2. with item 1 above, I continued to do SETUP>>BASIC SETUP>>DHCP RESEVERSATION. I can see the compute/sever name and the 192.168.1.128. I then click the "select" and save the client.I restarted the computer/server, I unplug and plug the E2500 power. I check the server internal IP address and it is still the same. But I just cannot browse to my website. I can browse other places.

View 9 Replies View Related

Linksys Wireless Router :: WRT610N - Way To Set Up Port Forwarding

Jun 26, 2012

I am finding it impossible to set up port forwarding. No matter what I do I remain completely stealthed when I do a port probe via [URL]... The only way I seem to be able to open a port is if I enable remote management. When I do that, whatever port I specifiy as the remote management port is then fully open. Obviously, I can't leave a port exposed like this and, anyway, I need to open multiple ports for my purposes.

View 9 Replies View Related

Linksys Wireless Router :: E4200 Port Forwarding?

Feb 26, 2013

I use modem and router to connect to the internet.When I connect my PC directly to modem port forwarding is working.When I connect my PC through my router  the port is closed. I followed instruction for port forwarding.

View 9 Replies View Related

Linksys Wireless Router :: Port Forwarding With BEFW11S4

Sep 16, 2011

I'm trying to port forward with the Linksys BEFW11S4, I've followed all the instruction from support website. I went to the Application & Gaming then Port Range Forwarding. I changed the settings so I can access this IP remotely. When I try to log into this IP from a different network it wont let me.

View 5 Replies View Related

Linksys Wireless Router :: Port Forwarding E4200 V 1.0.04?

Nov 2, 2012

I am trying to port forward my Linksys e4200 router v 1.0.04. However, it is not successful for when ever I check if the ports are open they fail they test.
 
I am sure that I am doing the actual port forwarding correctly (I hope), but something is refraining the ports from being open.

View 9 Replies View Related

Linksys Wireless Router :: Port Forwarding On A WRT120N?

Nov 2, 2012

I am trying to install and use EchoLink on my pc's and they require port forwarding for 5198-5200 but I'm having trouble with theTo IP Address" as I don't know what # to use.  It says I can't use 192.168.1.1 since it's the same as the LAN IP address so what do I use?  I am trying to follow the instructions on [URL]   If I leave it just as 192.168.1. it won't accept it and if I use any other number, it accepts it but I still can't get through.

View 3 Replies View Related

Linksys Wireless Router :: EA2700 - NAT And Port Forwarding?

Feb 6, 2013

My first issue with this device is when I try to untick NAT to disable it I lose my internet connection. This also disables access to router's address 192.168.1.1 forcing me to reset the device and set it up all over again. Why is this happening? I tried this at least five times with the same result. Second question I have is if the DHCP reservation is the right option if I want to forward ports for certain applications like Vuze? When the DHCP reservation window opens I see all my wireless devices in the list (laptop, phone) but not the main computer which is connected through ethernet port. But that is yet another problem.
 
I've got a cable modem, connection is set to Automatic DHCP and I all want is to disable all firewalls, NAT and other unnecessary protection that's slowing my internet speed, set up MAC address filtering, port forwarding and close this terrible software so I never have to see it or think about it ever again.

View 2 Replies View Related

Linksys Wireless Router :: Port Forwarding On A WRT120N

Nov 1, 2009

I just bought a WRT120N wireless router, and have run into some strange problems with port forwarding. I have a two router setup, because my ISP have set it up so i can only use my router from them to get my connection, and then i just have that one connected to my WRT120N. So my setup looks like the following:
 
The problem is that ONLY the three first ports works. I have forwarded them in the exact same manner, give it a name, put in the same external and internal port, and enable the port forwarding, but according ot can you seeme.org, only 4667, 6112, and 4669 can be seen, the rest is not responding. I even tried to enable port 21, which is a default setting in the router, but it will just not work.I have of course tried to reboot both router and PC, upgraded the routers firmware, but no luck.

View 9 Replies View Related

Linksys Wireless Router :: E4200 Port Forwarding On TCP / 80 And 443

Aug 31, 2012

I'm a happy user of the E4200 for a few weeks now, and all in all it's a very robust and useful router.Within my network I have a webserver running using both HTTP (TCP 80) and HTTPS (TCP 443). I want to make this webserver available to the internet and so I configure port forwarding to forward port TCP 80 and TCP 443 to my internal webserver. As soon as I now apply these settings, I loose connection to the webinterface of the E4200 and get connected to my internal webserver. I would expect the router would only forward connections coming in through the external interface of the router, however this is apparently not the case (or at least not in my setup). So I tried setting up remote management on a different port to at least allow me to remotely manage the router, but this does not work from my internal network.
 
Right now, I'm assuming I'm doing something wrong, or have miss-configured something. Is it possible to switch the webadmin port to a different port (like 8080 and 8443)?

View 1 Replies View Related

Linksys Wireless Router :: WRT54G V8 Port Forwarding?

Mar 30, 2013

I'm trying to forward my ports and I've been following a guide from [URL]. It's simple, but it's not working for me. I couldn't find my router on their list, so I'm assuming the worst and that it's not supported for the Port Forwarding. I just went with the normal WRT54G without the version 8 and tried it that way, I didn't get anything out of that either. It keeps telling me that the port isn't open and I can't receive the information packets that they're sending me. 

View 3 Replies View Related

Linksys Wireless Router :: Port Forwarding With EPC 3925

Nov 14, 2012

Im going to change my NAT status to "open" on my xbox 360, but I don't have access to the router I think. Its my grandmas internet and im going to be here for 10 days so it could be nice if you could tell me the username and password so i can open the ports?

Model:Cisco EPC3925Vendor:CiscoHardware Revision:1.0 MAC Address:18:59:33:ad:b0:a0Bootloader Revision:2.3.0_R1Current Software Revision:EPC3925-ESIP-16-v302r125532-110504cFirmware Name:epc3925-ESIP-16-v302r125532-110504c.binFirmware Build Time:May 4 17:40:26 2011Cable Modem Status:OperationalWireless Network:Enable  

View 1 Replies View Related

Linksys Wireless Router :: WRT54G - Port Forwarding Setup

Feb 12, 2012

I'm trying to set up my WRT54G wireless router so.i can port forward the relevant ports for my programs. I understand that you have to set up a static ip address before you can do a port forward which makes sense as you do not want to keep changing the ip address for the forwarding settings every time your network refreshes. But I cant seem to have it set up. And is there a rule that the static ip that you set should not be within the dhcp range?After setting up the static ip and setting up the port forward settings how do I test if the port is being forwarded correctly?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved