Linksys Wireless Router :: E2500 Web Interface Doesn't Work In Bridge Mode
Jan 10, 2012
I recently bought a Cisco E2500 for work, and after setting the router to Bridge Mode, I am unable to access the router web interface. I tried both the old IP address (192.168.1.1) and the IP address that I entered when I was configuring Bridge mode, but I couldn't get either to work. I have always tried resetting the switch to factory defaults and trying again to make sure I didn't type anything wrong, but to no avail. The wireless and everything works as it should, I just can't get back into the router to change any of my settings.
View 4 Replies
ADVERTISEMENT
Aug 9, 2011
We have three brand new E4200 routers, all using the most current firmware (1.0.02). They are all in bridged mode, however when I attempt to enable the guest network on each of them, the config shows it as active, but it never shows up as visiible SSID. In previous posts, I've seen people saying that I need to do a complete hard reset of the router and re-enter all the configs again to get the guest network active. Is this true? I'd hate to think that I have to hard reset and reconfigure all three of these APs, just to get the guest network enabled.
View 2 Replies
View Related
Sep 14, 2011
I just bought an E2500. Wanted to set it up in bridge mode. I can't seem to find any way of doing this.Cisco Knowledge Base article # 4194 shows what I am attempting to do.
View 1 Replies
View Related
Jan 25, 2012
My client has a DSL modem and a Belkin wired 4-port router configured to connect to it using PPPoE. Apparently there is no way to configure the E2500 such that it may be dropped in as a direct replacement for the Belkin (which would also provide wireless access) without the PPPoE login/password (from the DSL provider, Verizon).
I would like to connect the "Internet" port of the E2500 to one of the Belkin's 4 ports, in order to use the E2500 for wireless internet access without using any of the 4 wired ports but I think this creates a NAT within an existing NAT network?
To avoid that if I configure the E2500 in wired bridge mode, it becomes transparent, and I can no longer access its administration interface using the address 192.168.1.1 (since that address belongs to the Belkin). How may I, for example, change the wireless password which the E2500 is in wired bridge mode?
View 1 Replies
View Related
Nov 18, 2012
I accidently went into bridge mode on my linksys E2500 router. I want to reset it back to normal but i'm not sure how to do it. i tried the little reset button on the router but that didn't change it.
View 4 Replies
View Related
Aug 1, 2012
I have a mac 10.7.4 and an xbox 360 slim. Whenever I try to play online like cod or fifa and someone else is on the computer It is super lagy, Laging. Before when I had a **bleep**y netgear 33 mb it worked perfectly fine. Now this router is has 300 +mb and it stil doesnt work. This router cost me $80 dollars. Before cisco linsys I bought a netgear not the **bleep**ty neatgear but a newer one and it still had the same problem.
View 1 Replies
View Related
Feb 23, 2013
Blank user name and admin in password doesn't work. How to reset these ?
View 1 Replies
View Related
Aug 20, 2011
I have an ADSL Modem WAG200G Annex A, with latest firmware. I recently purchased a Linksys E2000 to upgrade my wireless to N, plus to get 4 gigabit Ethernet Ports for my NAS.
The problem is, I set WAG200G to "Bridge mode only", and from within E2000, I provided PPPoE credentials (user name and password), it does not work, no Internet connection!
Normally, with the WAG200G, PPPoE credential is set as followings (and it works)
Type: PPPoE Multiplexing: LLC Virtual Circuit: "0" for VPI (0~255) and "33" for VCI (0~65535) "Keep Alive" option
on E2000 Router, PPPoE does not have the above option for me to select. Only User Name and Password field
View 4 Replies
View Related
Apr 21, 2007
I'm trying to configure my WAG200G to work in bridge mode so that it can transfer my external IP address to my ISA server.My network map is very simple,Internet -- WAG200G -- ISA Server -- LANCan
View 7 Replies
View Related
Feb 25, 2012
just replaced my WRT54GL with e2500 and i have a problem connecting my bridge (WET610N) to e2500 router, it connects fine, but no internet when i connect the bridge to another PC (bidrge says it's connected and got IP), same story with another router (WRT54GL) i connect it with the wire to the e2500 than connect to that router with wi fi and OOPS no internet when i connect to e2500 directly with laptop, iphone etc i have the internet connection, but when i connect the bridge or another router i get no internet looks like E2500 does not let the internet pass throught the bridge or other router.
View 3 Replies
View Related
Mar 12, 2012
I have a WAP54G v3.1 running firmware version 3.05.01 and a WRT54G v3 running Tomato v1.28. The WAP54G is configured client mode and works perfectly. However, I was not able to get the two to communicate with WPA2 security - maybe, I just didn't try hard enough? Both devices are capable of doing WPA2 with AES but client mode doesn't seem to work with WPA2? I had to drop back to WPA-AES to make it work. Why is this?
View 4 Replies
View Related
Mar 20, 2012
Just successfully replaced a WRT54GL with E2500 as my primary router. Everything went great and the setup of the new router was easy enough. Everything just works.
Except one thing: the new router doesn't act as a DNS server on my network. Therefore, my network shares do not reconnect and I cannot ping the machines using their network name, only their IP addresses. Running ipconfig /all shows 192.168.2.1 as my default gateway and DHCP server, but not as a DNS server. I'm positive that my "old" WRT54GL was acting as my DNS server
View 2 Replies
View Related
May 2, 2012
We are deploying a new office and exploring the options for WLAN deployment. We were pretty impressed with 3500 series APs and that it supports CleanAir.However, we have decided to go for standalone AP deployment model now. As 3500 does not work in standalone mode, so we are looking for APs that can work in standalone mode ( and later can be converted to lightweight if needed). We can go for 1140 in that case. However, it would be better for us to know the main differences between features supported by 3500 lightweight AP and 1140 standalone AP. CleanAir looks like the main one. Are there other important ones as well?
View 2 Replies
View Related
Dec 6, 2011
What is the maximum allowed number of wired clients behind a workgroup bridge? In other words, is there a limit on MAC addresses?I assume 1262 AP in WGB mode is connecting to a lighweight AP (1262 or 3502), latest IOS and WLC software. I wasn't able to find the answer from Cisco documentation.
View 2 Replies
View Related
Apr 2, 2012
IPort forwarding simply does not work with this rounter on Comcast. I called comcast to see if they were blocking ports and they insist they ARE NOT.So what can it be? Was on FIOS with their modem/router combo and port forwarding worked like a charm with them.I've tried single port forwarding, port range forwarding, yada.
I am using the correct internal IP address on the machine I want to enable port forwarding on..Latest firmware is installed 1.04 or whatever (just purchased the router and updated during the Cisco Connect install on the 29th). Guess I should go find a cheaper router that actually works...
View 7 Replies
View Related
May 1, 2012
I have a E4200 with 1.0.04 firmware that I've used for a while as a router in front of a cable modem. I have upgraded the modem to a Virgin Media SuperHub. I have connected my E4200's WAN port to one of the SuperHub's LAN ports and changed the E4200's mode to Bridged Mode.I can connect to the Internet wirelessly and wired on the SuperHub, but I can only connect to the Internet via the E4200 if I'm wired to it. The wireless will connect to the E4200, it gets allocated and IP address in the correct range and the gateway is shown as the SuperHub's IP address, and I can see the E4200's management website via wireless, but I cannot connect to anything beyond the E4200.
View 9 Replies
View Related
Feb 16, 2013
I bought the EA3500 nine months ago mainly for the USB port (for a NAS). I recently replaced Comcast Cable with Verizon FIOS. So I now have the FIOS router as my main router (its' IP address is 192.168.1.1). I put the EA3500 in bridge mode to extend the (wired) network. I could get: After going in to bridge mode (with DHCP), I can not log in to the EA3500 (IP address 192.168.1.5 assigned by the FIOS router). I connect my computer directly to one of the EA3500 numbered ports (after various combinations of rebooting EA3500 and rebooting PC). It just continues to say "waiting" and never logs in. Tried choosing a static route (tried both 192.168.1.43 and 192.168.1.5 with 255.255.255.0, gateway and DNS1 = 192.168.1.1) with no luck.Since I can't log in, I cannot set up my NAS on the USB port of the EA3500 (so I haven't gotten far enough to determine if the USB port will even work in bridge mode).Thought about ensuring the latest firmware but since I can't log in I can't do that. (And after a hard reset EA3500 IP address is 192.168.1.1 which creates conflict with FIOS)
View 9 Replies
View Related
Sep 26, 2011
As I understand, the latest FW for the E4200 makes it possible to put he router into bridge mode. In this mode, I can use it as an access point. In bridge mode, should I then connect my router to the WAN port at the E4200?The other way to make the E4200 into an AP, is to disable DHCP and NAT and give the E4200 an IP address out of range for the DHCP range in my preferred router.
Choosing between this two option to make the E4200 into an AP, which is considered to be the best solution?And to be sure; using this option, then the Ethernet cable should be connected to the LAN port of the E4200? is the performance of an E4200 in AP mode the same as a dedicated AP like the WAP610N?
View 3 Replies
View Related
Aug 20, 2011
Just bought 2 e4200's! I have the first one connected to the ATT router, and I have the second one connected to the first in Bridge Mode. It works great! It knew how to configure itself to be the down-level client.
However, I noticed that the port speed is only 100 Mbps on the port that is acting as the link for the bridge. I am running brand-new CAT5e thru the house, and if I connect the cable directly to my laptop - I get 1Gbps. So I know that the cable is good.
Is there a way to change the speed of the INET port on the down-level e4200?
View 1 Replies
View Related
Jun 20, 2012
Started setting up a Linksys EA4500 Yesterday.
- Bridge Mode
- Router Address Manually specified
- Manual wifi setup
Regular access works. My smartphone obtains IP address, connects, accesses pages.Guest access loops through the "obtain IP address" step. Bridge mode might have a bug?
View 9 Replies
View Related
Dec 25, 2011
I have just received my 2 new cheap wrt54g2 routers. I already have a router with dhcp in my network, so I just need this routers to connect wired net and wireless. Is there any way to use this routers as a bridge? Earlier I used asus router, with disabled dhcp and lan cable connected to one of lan ports. But this is not comfortable, because I need to put ip address to router statically
View 6 Replies
View Related
Aug 22, 2012
I have a Wireless Router supplied by my ISP that give me both 1G Lan and N Band Wireless, so I just need to use my 4200V1 as a Storage Access Point. I have done all the Bridge Mode configurations, IP Address ad Subnet / Default Gateway, etc to the routher and can see it on my Local LAN, by it's Set name.
I can not http or Https to the Config menu in any way, so I can not establish if a Disk is connected or not. The Disk device is USB Connected to the E4200 port, but I can not acceeass any of the files that are on it.
DGW - 192.168.1.1
E4200 - 192.168.1.200
Bridge Mode
Wireless Disabled on both Bands
DHCP Disabled
Everything appears fine, but not able to bring up Advance Configuration interface .
View 2 Replies
View Related
Dec 26, 2008
I have just purchased t-mobile's at home phone service (voip) and they gave me a UTA200-TM Hiport Adaptor to connect for the service. Had Vonage (voip) for 2 years so know how it works and never had problems. This one however will only allow the phone line to stay on for about 30 seconds and then drop it. Have it connected to a modem (cable internet) and a WRT54GS Wireless Router. T-Mobile wants me to check to see if the router has bridge mode set up as they think that may be causing the phone line to drop out. How can I check that? I can not figure out the directions on the linksys site, too confusing.
View 3 Replies
View Related
Nov 5, 2012
Restarting the e4200 did not work. Resetting using the switch at the back did not resolve the issue. I was able to reset it via the 192.168.1.1 web page. After restoring my settings from backup, the issue remained the same. This was not alleviated after I updated the firmware. Plugging into one of the ports with a cat5 cable with my Mac, I was able to get an IP, yet I was not able to surf; same case with my MacBook.
Doing the 30-30-30 reboot did not fix this issue and all the while the front white light on the router went and stayed, solid.To see if I could get this to do ANY sort of meaningful internetting (is that even a word?) I put the e4200 in bridge mode and when I put the cable modem in, and all that plugs into this router works. This, of course, means that there is:
1. No Wifi signal and
2. It will not reset to factory settings.
View 1 Replies
View Related
Jan 16, 2013
I configured the EA4500 to work in bridge mode, to use it as an accespoint for an existing network (Linksys WRT610N). It gets an IP address (192.168.1.141), but does not offer a wireless network (the ethernet ports do offer network acces). When I try to access the configuration on IP address 192.168.1.141 I get the Linksys Smart Wifi page asking for the password. When I enter the password, a message "Waiting" appears and that's all. It keeps me waiting forever and I cannot access the configuration settings.I have tried to reset the router (30sec. reset button, power off 30sec, power on) but the result is the same.
View 6 Replies
View Related
Feb 7, 2012
I'm using the E4200 in Bridge mode and it's handing out IPs from our DHCP server (not acting as it's own). I have about 8 people connecting to this wirelessly to get to our network. For some reason it locked up once every week or two and I have to unplug it (can't even remote into it).
View 3 Replies
View Related
Aug 10, 2011
I have four E4200 units on my network, each with an unique IP address, in bridge mode to act as a wireless mesh across my entire building. They are all connected to my central L3 switch, via their Internet ports.
Is it possible to enable the Guest network on each unit, to create a 'Guest Wifi' mesh (providing that I allow the 192.168.33.0 network to route across my network fabric), or will this not work because each indivudual AP will be assigning IP address 192.168.33.1 as it's gateway address meaning that I would have four distinct MAC addresses within the network, each trying to claim that they are IP 192.168.33.1?
View 2 Replies
View Related
Mar 15, 2012
I have an E4200V2 with the latest .36 firmware installed.The E4200V2 is setup in Bridge Mode. THe 4200 DHCP's an IP for itself from my network infrastructure. This consists of a UBEE DOCSIS 3 (gig E output) modem on a 100 meg cable connection feeding an IP Cop Linux router/firewall and out to a gig switch, fully gig E on the network side. The wired portion of the network is absolutely bulletproof. And the older B only AP that ran well was also on this same setup.I have the E4200V2 set for N only on the 5 GHz side, and I had it set to Auto for channel selection, but manually set an unused channel currently. The 2.5 GHz side is set also manually to a locally unused channel now, and is set to mixed mode as I have B/G/N devices I need to connect to. The unused channel for both radios was detemined by scanning for AP activity using one of my Linux laptops. I have both the 5 GHz and 2.5 GHz radios set for 20/40 channel width. And I am using the recommended WPA2-Personal for security on both, with a separate SSID name for each radio.
The wireless connection for both E4200 V2 radios disconnects on fairly random but regular times and has to reconnect. This happens on both radios. There is no interference, and no network feed issues that would cause this. And the older B only Orinoco AP I replaced never had these issues. Signals are strong to all of the devices and the dropouts occur even when testing with a laptop several feet from the E4200V2. If I am streaming a video over GoogleTV or music or playing an online game, the 4200 disconnects regularly and the devices need to reconnect. This happens on both radios and to every device.
View 9 Replies
View Related
Jul 14, 2011
The latest firmware seems to support bridge mode. Does it mean the router can connect to another router wirelessly in the bridge mode?
View 6 Replies
View Related
Oct 12, 2011
Well I accidentally put the router in bridge mode. It's a e1200 or 2500 I'm not exactly sure. But I was wondering how I can get it out? I can't access the web interface at 192.168.1.1 however I can access my modem's interface at 192.168.254.254.
View 4 Replies
View Related
Jan 3, 2012
I have a Fiber to Ethernet connector from my ISP. The Ethernet cable goes to an iSP issued Zyxel router. Into this router the landline phoneservice connects to give us VoIP landline service (which is cheaper). An Ethernet cable goes from the Internet port on the E4200 to a LAN port on the Zyxel router. That works great but I had to put the E4200 into Bridge Mode to get it to connect to the Internet via the Zyxel router which I need to use the phone services my ISP provides. I bought the E4200 because I wanted to use the dualband functionally and get a 802.11N 5GHz network setup and to give me the ability to block certian websites and services which I knew Cisco/Linksys is famous for - the abillity to control your network.
Well then imagine my surprise when I could not use the Parental Control settings when the router is in Bridge Mode... This was the reason I bought this router over an Apple Airport Exreme. Is there anyway to get it to let me use the Parental Control anyway while in Bridge Mode or a better way for me to connect the router with the rest of my network?
View 3 Replies
View Related
Jul 11, 2012
Im trying to bridge my zyxel eq660r-f1 dsl modem so that i can resolve the nat issue im having in my home network. Only problem is that everytime I bridge the modem and hook my E4200 up, I cannot connect to the internet. If i connect my laptop directly to the modem, I do get internet but not through the router itself.
View 8 Replies
View Related
Sep 6, 2011
I have spent most of the weekend trying to get this router to act as a proper Access Point.
When it does work (Stay connected) speeds and latency are rotten. If I go back to Routing Mode this thing kicks butt, but I isolate all devices attached to a different subnet and trying to set up proper routes has proved imposable. Firmware 1.0.2 r 13
The online help stated to connect to the "internet interface" when in Bridge Mode DHCP Server Is not broadcasting to on the wireless or wired interfaces.
If I used the wired interface as the uplink I can broadcast the DHCP to any device on wired but again nothing to the Wireless. When I "Show Routing Table" I see two static routes pointing to the ATT router for the Wired/Wireless Interfaces.. 0.0.0.0 255.255.255.0 (my Gateway) Wired/Wireless (my Gateway) 255.255.255.0 0.0.0. Wired/Wireless
AP mode should only be working in Broadcast. By connecting the Wired Interfaces alone up to my switched network should not use the router at all. If you force all traffic to my router all traffic has to be inspected by the firewall You create a bottleneck my router interface is 10/100.
ATT 2 Wire Gateway/Router with pinholes. 10/100/1000 Non managed 24 port Switch Network. Server infrastructure serving DNS/DHCP.
I decided to buy this after reading it offered Bridge/Access Point mode instead of getting the WAP610 because I wanted to have the option to change to routing mode or AP mode. Since my ATT Uverse Router Wireless is “g” it takes forever to transfer files to and from my servers.
View 4 Replies
View Related
