I'm trying to configure my WAG200G to work in bridge mode so that it can transfer my external IP address to my ISA server.My network map is very simple,Internet -- WAG200G -- ISA Server -- LANCan
View 7 RepliesI have an ADSL Modem WAG200G Annex A, with latest firmware. I recently purchased a Linksys E2000 to upgrade my wireless to N, plus to get 4 gigabit Ethernet Ports for my NAS.
The problem is, I set WAG200G to "Bridge mode only", and from within E2000, I provided PPPoE credentials (user name and password), it does not work, no Internet connection!
Normally, with the WAG200G, PPPoE credential is set as followings (and it works)
Type: PPPoE Multiplexing: LLC Virtual Circuit: "0" for VPI (0~255) and "33" for VCI (0~65535) "Keep Alive" option
on E2000 Router, PPPoE does not have the above option for me to select. Only User Name and Password field
I tried to set my WAG200G as a wireless bridge, but I encountered some problems doing so.
First I reseted the router to factory default settings, then I put it in "bridge mode only" disabled DHCP and UPnP (this was required for the college network I want to use on it to work). Then I put the UTP cable in one of the LAN ports.
When I try to acces this network though a wire everything works fine, I can see the other devices connected to the network and I can acces the internet. When I try to use the network wirelessly, I still see the other devices on the network but I can't connect to the internet. (The acces to the internet is gained by logging in inside the browser, like with wifi hotspots)
I'm using Linksys WAG200G Wireless modem and connection mode is "Bridge Mode Only", in this mode I'm not getting the 192.168.1.1 setup console and Wifi facility.
View 3 Replies View RelatedI have been using a Linksys Wireless-G ADSL WAG200G, Annex-A Gateway Router and it has been fine, now my ISP have told me that they are modernising the network and will need a router capable of managing ADSL2/ VDSL connections, so will my router be able to do that or will I have to buy a new one? It has firmware 1.01.09?Edit: I see in the DSL Modulation menu which is set at present to "Multimode" I also have options to select ADSL2, ADSL2+, ADSL2 AnnexM, ADSL2+ AnnexM and ASDL2 AnnexL but I do not see any mention of "VDSL"
View 2 Replies View RelatedOur family has about three computers that use a wireless network that we all share. We have an old Gateway, a WCG200, that is bridged to an E2000, which was set-up ever since we required better security when someone used our connection to illegally obtain movies. We got a letter which warned us of any future violations that could cause legal action, so we looked into our wireless connection to better secure it from any other individuals outside of our household. The WCG200 is connected to the outlet in the wall via cable, and then connects from the Ethernet to the E2000. The E2000 has a stronger security setup than the WCG200, which is the advice we received from our ISP and would allow us to keep the Gateway. It provides a strong signal, but from time to time, we suffer latency or slow loading through all of our online devices, even though our connection speed displays a solid 72.0 Mbps. I've tried the Event Viewer to see any problems, and I have noticed some small things:
- WLAN AutoConfig service has successfully stopped.Wirel?
- WLAN Extensibility Module has stopped. Module Path: C:WindowsSystem32cmihvsrv64.dll
- The server {E10F6C3A-F1AE-4ADC-AA9D-2FE65525666E} did not register with DCOM within the required timeout.
- Broadcom NetLink (TM) Gigabit Ethernet: The network link is down. Check to make sure the network cable is properly connected. [This last one is strange, since I use the Wireless Network Connection with a DW1501 Wireless-N WLAN Half-Mini Card, while the Broadcom adapter is under the Local Area Connection and displayed as not connected.]
Other than that, I'm not quite sure what the recurring problem comes from. Our WCG200 has a firewall enabled and our E2000 has an SPI firewall enabled. The security mode of the E2000 is a WPA2 setup. We have disabled the wireless network of our WCG200 in order to make use of the E2000.
I have a WAG120N. I wish to use it as a modem only and not as a wireless router.I have another wireless router I want to use to handle network connectivity.I want the wag to be set to 10.10.1.1 and I want my router on 10.10.1.2What bridge mode do I set on my wag? Do I need a crossover cable?
View 1 Replies View RelatedI'v just changed my internet provider. That new one uses Annex b, my wag160n is purposed to annex a. Thats what i'v done. Turn on bridge mode turn off dhcp, set PPPoE with my login and password. And here is my problem. I cant connect by wifi with more then 1 device. I can only connect with my laptop when i'm trying to connect on my xbox it says it cannot get ip adress from router. What shoudl i change ?
View 6 Replies View RelatedI recently bought a Cisco E2500 for work, and after setting the router to Bridge Mode, I am unable to access the router web interface. I tried both the old IP address (192.168.1.1) and the IP address that I entered when I was configuring Bridge mode, but I couldn't get either to work. I have always tried resetting the switch to factory defaults and trying again to make sure I didn't type anything wrong, but to no avail. The wireless and everything works as it should, I just can't get back into the router to change any of my settings.
View 4 Replies View RelatedMy client has a DSL modem and a Belkin wired 4-port router configured to connect to it using PPPoE. Apparently there is no way to configure the E2500 such that it may be dropped in as a direct replacement for the Belkin (which would also provide wireless access) without the PPPoE login/password (from the DSL provider, Verizon).
I would like to connect the "Internet" port of the E2500 to one of the Belkin's 4 ports, in order to use the E2500 for wireless internet access without using any of the 4 wired ports but I think this creates a NAT within an existing NAT network?
To avoid that if I configure the E2500 in wired bridge mode, it becomes transparent, and I can no longer access its administration interface using the address 192.168.1.1 (since that address belongs to the Belkin). How may I, for example, change the wireless password which the E2500 is in wired bridge mode?
different ways to connect a printer to the X3000. how to connect a printer to the X3000, i.e. wirelessly, USB port, or directly via one of the LAN ports. I also checked the product information for X3000 on the CISCO website and it only makes reference of the USB port as StorageLink.
. Since then I have reconsidered and now am looking to purchase the E4200V2 to connect in bridge mode to my X3000 instead of the E1500. Correct me if I am wrong but connecting the E4200V2 to my X3000 should be the same connecting the E1500 to my X3000, i.e. bridge mode? Yes or No?And my final set of questions is rregarding what would be the best set-up for adding a storage device and printer to my network once I get the E4200V2 and set it up in bridge mode?
- Should I connect both the printer and storage device to my the E4200V2?
- Should I connect them both to my X3000, which provides my internet connection?
- Should I connect one to the X3000 and one to the E4200, if so which to which for best set-up?
We have three brand new E4200 routers, all using the most current firmware (1.0.02). They are all in bridged mode, however when I attempt to enable the guest network on each of them, the config shows it as active, but it never shows up as visiible SSID. In previous posts, I've seen people saying that I need to do a complete hard reset of the router and re-enter all the configs again to get the guest network active. Is this true? I'd hate to think that I have to hard reset and reconfigure all three of these APs, just to get the guest network enabled.
View 2 Replies View RelatedI need to configure a WAG 120 N as a bridge, so I can have my public IP as an output of an Ethernet port. I need this configuration because I have a non ADSL router managing VPNs and needs the public IP on the WAN port of this router.
View 3 Replies View RelatedMy apartment already has internet provided to all of the rooms, but I'm trying to set up my router as a wireless access point. I tried disabling DHCP on the router, but then I wasn't able to get any internet access at all. Does this device not support bridge mode?
View 5 Replies View RelatedIs it possible to configure bridge mode in asa 5505 if it is can u provide me a config.
View 1 Replies View Relateda customer got an 1552 outdoor AP in local mode and installed it at a building. It has to run as a Mesh AP (MAP). Now the AP connects one time to the WLC 5508 and started a download. After that, the AP never came back. Like we saw on the other installed 1552 RAP's, they all where in local mode.We configured all AP's to bridge mode, but the MAP could not join anymore.Is there a CLI command to change the mode on the AP itself?From the WLC it's not a problem, but for the AP CLI I cannot find sth.
View 1 Replies View RelatedI want to configure two AP WAP4410N in Bridge Mode and I don´t find the correct configuraction tips.
View 11 Replies View RelatedI am new to cisco ASA. I need to configure ASA 5520 in transparent bridge mode. [code] I need to place the new asa firewall in transparent mode. How to configure the firewall in transparent bridgmode.
View 5 Replies View RelatedI want to achieve the following setup:
So basically I have a C877 and a Cisco ASA 5505 and I want to push the public IP of the ISP to the outside interface of the ASA so the Cisco 877 will only be responsible for ADSL and PPPoA. Don't ask me why I don' t use a modem/router instead. I know that is a waste to use the C877 in this way but I want to test the setup.
Right now the config of the C877 regarding ADSL and PPPoA looks like that ( I don't have the ASA connected yet, so all the PC are connected directly to the C877 right now):
interface ATM0 no ip address load-interval 30 no atm ilmi-keepalive pvc 0/35 encapsulation aal5mux ppp dialer dialer pool-member 1
interface Dialer1 ip address x.x.x.x 255.255.255.248 ip access-group OUTSIDEACL in ip nat outside ip inspect FWRule out ip virtual-reassembly encapsulation ppp dialer pool 1 ppp authentication chap pap callin ppp chap hostname xxxxxxx ppp chap password 0 xxxxxxx ppp pap sent-username xxxxxx password 0 xxxxxxx
ip route 0.0.0.0 0.0.0.0 dialer 1
ip nat inside source route-map Nat interface Dialer1 overload
interface vlan 100 is my LAN configured with DHCP.
how I should configure the C877 to push the public IP to the ASA?
Possible using a firmware upgrade to change the wag200g from annex B to annex A?T
View 6 Replies View RelatedI have been using Linksys WAG200g as a modem&router at my home for few years already and it did a great job. Plugged it on 24hours non-stop. Default firmware.
However, in the past months WAG200g did the factory reset by itself. It happened once a month, 3 months in a row already. No body pressed the reset button nor use the web admin to reset it. It reset itself. All the SSID, IP Address, passwords, etc are reset to default.
Tried connecting my laptop...internet doesnt work. Tried doing restarts and stuff nothing seems to work.
View 1 Replies View RelatedI Have a WAG200G wireless modem but I can not activate VPN on my Phone 4 , but it is easily done by Zyxel modem.
View 4 Replies View RelatedI set the access restrictions as instructed but they refuse to work. Firmware version is :-1.01.05,have rebooted, with no success.
View 6 Replies View RelatedMy internet provider servers internet, telephone an digital cable TV to my flat.For using this, they sent me an AVM Fritz Box.It really works well..... except file transfers over LANWhen I try to copy more or less large files (above 4 GB) the Fritz Box fails, freezes or just drops all network connections...However: I hate this thing.
For my old provider, I brought my Linksys WAG200g and it really worked fine - due to this I'd like to install it the following way:
ISP -> Fritz.Box -> WAG200g -> LAN
how to update the firmware for WAG200G? I've downloaded the firmware from internet, but i don't know what to do next...
View 3 Replies View RelatedWell, I am just curious, how much hard disk does a WAG200G has? And how much memory and what processor? Is it hard to point me to a datasheet including every chip or/and component it has?
View 3 Replies View RelatedI want to connect my wag 200g to another router. My other router have ip address 192.168.2.1 and is connected to my isp and my wag 200g is 192.168.1.254. What i want is to connect my wag 200g to the other router and to share the internet connection. I want also the dhcp server on the wag 200g to assign ip address to the wireless users connected on the wag 200g with ip addresses to the network 192.168.1.0.
View 2 Replies View Relatedwhenever the phone is in use i.e. a call comes in or the phone is being used to dial out, the connection will drop. I have tried changing the microfilter on the Phone Socket, and it seemed to resolve it for a while.Should I perform a Factory Reset? I am using the latest firmware which is 1.01.06 ?
View 1 Replies View RelatedHaving the issue for over a year now, I'm wondering why there isn't a fix for the mentioned connection drops of the WAG200G? I'm on the newest firmware now (1.01.08(3)) but still every so many minutes: bam, lost connection.
View 9 Replies View Relatedwhenever the phone is in use i.e. a call comes in or the phone is being used to dial out, the connection will drop. I have tried changing the microfilter on the Phone Socket, and it seemed to resolve it for a while.
Should I perform a Factory Reset? I am using the latest firmware which is 1.01.06
We have a RV120W Wireless-N VPN Firewall and we want to configure the router in brigde mode (transparent). Because we have another Firewall, use for filtering and default gateway on the LAN. The ISP provide IP address by DHCP, so we must connect the internet connexion to the WAN interface. But How can we do for connected the RV120W to our firewall? The router mode on the RV120w allows-it to make this configuration?
View 1 Replies View RelatedWhat is the maximum allowed number of wired clients behind a workgroup bridge? In other words, is there a limit on MAC addresses?I assume 1262 AP in WGB mode is connecting to a lighweight AP (1262 or 3502), latest IOS and WLC software. I wasn't able to find the answer from Cisco documentation.
View 2 Replies View Related