Cisco Routers :: RV120W / Configure Bridge Mode For Internet Access?
Jan 1, 2013
We have a RV120W Wireless-N VPN Firewall and we want to configure the router in brigde mode (transparent). Because we have another Firewall, use for filtering and default gateway on the LAN. The ISP provide IP address by DHCP, so we must connect the internet connexion to the WAN interface. But How can we do for connected the RV120W to our firewall? The router mode on the RV120w allows-it to make this configuration?
View 1 Replies
ADVERTISEMENT
Sep 11, 2011
I am trying to configure a BT Business ADSL Router (BT2700HGV) to work in bridge mode in front of a Cisco RV120W router and cannot get this to work.I have followed numerous posts I have come across in configuring the BT router for bridged mode and this has been configured as follows:
ATM Encapsulation - Bridge LLC
DSL and ATM - VPI=0, VCI=38 (also tried VCI=35)
ATM PVC Search - Disabled
Connection Type - Direct IP (DHCP or Static)
Disable Routing - Yes
There are also some other options on the same configuration page for 'Broadband IP Network' (which I have left on DHCP) and also a 'Public IP' which has been left blank. After setting the above options this removes the LAN DHCP configuration, the PPPoA logon details and sets the internal IP address of the BT router to 192.168.1.254.
My understanding of 'Bridge' mode is that this router will now act simply as a modem and configuration details such as logon details and WAN IP address information are configured using the Cisco RV120W router?The configuration of the Cisco router is as follows:
Internet Connection Type - PPPoE
Username and Password set
Authentication Type - Auto-Negotiate (options here are PAP, CHAP, MS-CHAP and MS-CHAPv2)
Routing Mode - Router (Other option is 'Gateway (NAT))' - I have tried both options
The WAN interface on the Cisco router is connected to one of the LAN ports on the BT router. The 'Broadband' light is on the BT router but the 'Internet' light isn't. The WAN status on the Cisco router is 'Connecting'. I am sure I am missing something simple.We have been assigned a range of static IP addresses from BT so am trying to get these working too (x.x.x.24/29 - 5 usable statics), another option available (other than PPPoE) for configuring the WAN interface on the Cisco router is a 'Static IP', not sure if this is the correct option but have tried messing with it, I have tried assigning a static IP from the range given to us (.30 - the router address specified by BT) along with the subnet mask, however don't know what to put as the default gateway, would this be the peer address (but assume that would change anyway), in any case, using the 'Static IP' option does not give an option to supply the BT logon details which I assume is required?
In bridged mode, what is the peer address assigned to, the BT router or the Cisco router?Does the BT router need to be configured with a public IP address?
View 2 Replies
View Related
Jun 8, 2012
Can the rv120W be configured as a wireless bridge? We have a need to configure a vpn connection to a remote building but will need to connect the router via an existing wireless network.
View 4 Replies
View Related
Apr 4, 2012
How does one configure the router so that Internet users can access internal company websites? The only thing that appears is the Cisco router login. Also I need to configure Terminal Services and its not on the list under Service.
View 2 Replies
View Related
Aug 23, 2011
My apartment already has internet provided to all of the rooms, but I'm trying to set up my router as a wireless access point. I tried disabling DHCP on the router, but then I wasn't able to get any internet access at all. Does this device not support bridge mode?
View 5 Replies
View Related
Feb 10, 2012
I want to know if it is possible to put the cisco small business router rv120w into bridge mode so that I can connect it to a linksys e2500 access point. Is this even possible or am I wasting my time?I have 4 devices connected to the cisco router that I want to be able to bridge to the linksys e2500 which has the internet connection.
View 1 Replies
View Related
Apr 26, 2012
I need to configure a rv120w in order to make it work at the same time for data and digital tv. The fact is that the set top box for the idtv needs an IP address that will be delivered directly from the ISP. So I need to setup one LAN port that will be bridged to the WLAN connection (the stb will be connected to that lan port), and another port that will be connected to the LAN swicth so that the rest of the network has internet access. I can't see anywhere a way to create such a bridge. Quite disappointing as it's possible to do so on open source platforms such as openWRT..
View 3 Replies
View Related
Feb 23, 2012
I have setup a site-to-site VPN tunnel between 2 sites using CISCO rv120w.Everything works fine; any PC on one site can access all systems on the other site and vice-versa.The issue I have is when I start a VPN connection another site on Internet using IPSecuritas.I can initiate a VPN to site 1 and site 2; but when connected, I can only access servers that are located into the same site I'm connected to; I cannot ping the remote site.The Range of IP addresses on the internet during my tests is 192.168.11.0 (I 'm using a Mac)
-Systems with IP 192.168.1.1 and 192.168.10.1 are bridges
-Systems with IP 192.168.1.2 and 192.168.10.2 are CISCO rv120w
View 4 Replies
View Related
May 30, 2012
I bought an rv120w. Now i want to trunk 2 lan ports to an smart switch to get 200MB out of that link.
The trunk mode in there in the manual that came in the cd with the unit i bought but is not in the web console.
I have updated the IOS to 1.0.3.10 to see if th trunk mode was there but is not.
My question is,
1 is that trunking feature there in the ios?
2- If not, why is listed in hte manual that came with the unit?
3- if it is in the ios, is there a was to by pass the web console and configure this?
4- can i do i maybe backing up the config then, editing the file and restoring it?
Screenshot below is from the manual in hte cd that came with the router
View 2 Replies
View Related
Aug 1, 2011
Is it possible to configure bridge mode in asa 5505 if it is can u provide me a config.
View 1 Replies
View Related
May 26, 2013
a customer got an 1552 outdoor AP in local mode and installed it at a building. It has to run as a Mesh AP (MAP). Now the AP connects one time to the WLC 5508 and started a download. After that, the AP never came back. Like we saw on the other installed 1552 RAP's, they all where in local mode.We configured all AP's to bridge mode, but the MAP could not join anymore.Is there a CLI command to change the mode on the AP itself?From the WLC it's not a problem, but for the AP CLI I cannot find sth.
View 1 Replies
View Related
Jun 16, 2011
I want to configure two AP WAP4410N in Bridge Mode and I don´t find the correct configuraction tips.
View 11 Replies
View Related
Sep 20, 2012
I am new to cisco ASA. I need to configure ASA 5520 in transparent bridge mode. [code] I need to place the new asa firewall in transparent mode. How to configure the firewall in transparent bridgmode.
View 5 Replies
View Related
Feb 16, 2011
I want to achieve the following setup:
So basically I have a C877 and a Cisco ASA 5505 and I want to push the public IP of the ISP to the outside interface of the ASA so the Cisco 877 will only be responsible for ADSL and PPPoA. Don't ask me why I don' t use a modem/router instead. I know that is a waste to use the C877 in this way but I want to test the setup.
Right now the config of the C877 regarding ADSL and PPPoA looks like that ( I don't have the ASA connected yet, so all the PC are connected directly to the C877 right now):
interface ATM0 no ip address load-interval 30 no atm ilmi-keepalive pvc 0/35 encapsulation aal5mux ppp dialer dialer pool-member 1
interface Dialer1 ip address x.x.x.x 255.255.255.248 ip access-group OUTSIDEACL in ip nat outside ip inspect FWRule out ip virtual-reassembly encapsulation ppp dialer pool 1 ppp authentication chap pap callin ppp chap hostname xxxxxxx ppp chap password 0 xxxxxxx ppp pap sent-username xxxxxx password 0 xxxxxxx
ip route 0.0.0.0 0.0.0.0 dialer 1
ip nat inside source route-map Nat interface Dialer1 overload
interface vlan 100 is my LAN configured with DHCP.
how I should configure the C877 to push the public IP to the ASA?
View 6 Replies
View Related
Apr 21, 2007
I'm trying to configure my WAG200G to work in bridge mode so that it can transfer my external IP address to my ISA server.My network map is very simple,Internet -- WAG200G -- ISA Server -- LANCan
View 7 Replies
View Related
Jan 25, 2012
My client has a DSL modem and a Belkin wired 4-port router configured to connect to it using PPPoE. Apparently there is no way to configure the E2500 such that it may be dropped in as a direct replacement for the Belkin (which would also provide wireless access) without the PPPoE login/password (from the DSL provider, Verizon).
I would like to connect the "Internet" port of the E2500 to one of the Belkin's 4 ports, in order to use the E2500 for wireless internet access without using any of the 4 wired ports but I think this creates a NAT within an existing NAT network?
To avoid that if I configure the E2500 in wired bridge mode, it becomes transparent, and I can no longer access its administration interface using the address 192.168.1.1 (since that address belongs to the Belkin). How may I, for example, change the wireless password which the E2500 is in wired bridge mode?
View 1 Replies
View Related
Sep 7, 2012
config to setup PPPoE on the cisco 831 router to be used with a modem in bridge mode. I have tired other peoples configs found on the web but, not all the commands were available on the IOS version thats on the router. Also note that I bought this as a used router and I dont have a service contract so I am unable to download an updated IOS. The router ver is 12.3(7)T9 and the IOS is c831-k9o3sy6-mz.123-7.T9.bin. Running config below is last tried still could not connect or get ip address from isp. [code]
View 2 Replies
View Related
Mar 20, 2011
Is it possible to put the SRP 527 into Bridge mode to use it just as a modem?
View 6 Replies
View Related
Feb 8, 2012
What is the default login/pass of cisco rv120w for ssh access ?
View 1 Replies
View Related
Mar 31, 2012
I had WRT54G2 and recently switched to an RV120W. I have an Internet accessible camera system connected to my router. Before, this worked fine... there is a dns service (DynDNS.com) that is configured as part of the camera setup. I would then just enter [URL] and I would connect to the cameras. I install the new router (RV120W) and I can no longer connect to the cameras. I do not recall any configuring that I had to perform on the old router.
why the RV120W isn't letting me get to the cameras?
View 3 Replies
View Related
Dec 5, 2012
I recently bought Cisco RV120W-E V01 and insall it in my home (with firmware 1.0.4.10). I want to establish PPTP conection from my notebook (when I am not at home) and to access (through VPN tunnel) to all hosts in my LAN (with no port restrictions). I configured VPN (PPTP) users and I can establish PPTP tunnel from client to RV120W. My traffic to Internet is going through VPN tunnel to RV120W and then out on Internet, and that is fine. What is not fine is that I can not access to any host on my LAN, and that is the main reason why I configured PPTP tunnel. It is not clear to me, when I am reading admin guide, what I have to configure to allow only my tunnel traffic to reach LAN hosts.
View 2 Replies
View Related
Jun 5, 2012
I've a Cisco SRP527W, it have a LAN in 192.168.1.0 range, now I need to put in bridge mode, to be transparent with my firewall, how can I do this?
View 3 Replies
View Related
Apr 2, 2012
is it possible to share the same network segment like my LAN for mobile users? In a so called bridge mode? I got a VPN tunnel to a customer from my local network and i need to access it within the mobile access. I can not change the VPN Site to Site tunnel.
View 2 Replies
View Related
Feb 27, 2013
I have a RV120W used to provide VPN access to several industrial devices. Some of these devices are assigned IP address via DHCP in the router. One cannot do DHCP, so it has a self-determined static IP.
The VPN works well for all the devices that are assigned IP's. However, it does not allow me to connect to the device that has a static IP. I can connect to it fine when I am on the LAN or WLAN, but cannot ping it via the VPN.
View 2 Replies
View Related
Sep 4, 2011
I have a RV120W Firewall and I've created 3 Vlans. One for Internet Access Computers, One for non-Internet access, one for printers. How can I implement security to keep Internet and non-internet vlan computers from communicating with one anothers? Both computer vlans will need to communicate with printer
View 1 Replies
View Related
Jan 27, 2012
My ISP insists that in order for me to have a home network use their router/modem ("2-Wire") for internet access, I must make my own network router act as a bridge since their modem is acting as the router. I.e. she said put your router into bridge mode. I don't know how to do that and Linksys won't offer assistance.
View 6 Replies
View Related
Jul 14, 2011
We have 4 access points in my network i want configure 1 is ap mode another 3 is bridge mode Is it possible to configure in 4410 N ? if i configure bridge mode can i use single SSID&Securtiy key for all aps. how to i use these 4 access points
View 1 Replies
View Related
Apr 3, 2013
I am trying to build a bridge between two of my access points. Both the access points connected to the wireless controller. I have changed the AP mode to "Bridge" after changing the power to custom.
The access points have both rebooted - but never "joined" the controller again. I have checked on the following pdf.
[URL]
One thing I can see - if I run a ping to the last IP.. every now and again I get a single response then it drops again. Via the console on the access point I can see it's getting to the controller, getting its name then reading something that caught my eye
"
*Apr 4 11:41:24.451: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Apr 4 11:41:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 57.24.10.53 peer_port: 5246
[Code]......
View 9 Replies
View Related
Sep 14, 2012
I installed DD-WRT on my router and placed it in bridge mode, configuring it with what I thought was my Androids IP address for the gateway. I tried with the Android IP address identified through cmyip.org, 208.54.32.156, and with the one identified through ipconfig command, 192.168.43.1. Neither address was successful. Also, I am unable to access my router using the IP address that I manually assigned to it.provide some assistance on the process of bridging from an Android to a wired PC through a router, Linksys WRT54G v3,
View 1 Replies
View Related
Feb 3, 2013
I have a Cisco RV120W router with 1.0.4.10 firmware. The router drop the internet connections, freeze/timeout in admin interface randomly. How can I determine that this is the router's fault, or if it's the switch / internet access is causing it?
View 4 Replies
View Related
Dec 20, 2012
Just bought a new router and repeater for a wifi hotspot i am currently running.. I thought i was havng problems with the repeater after i change from router to a server, (and i'm now using a router in bridge mode) so the server is managing all the dhcp.. etc, Hence, the router is Running as an access point. The server which is a Hotspot Server does the rest. For some reason, repeaters, do connect to the access point apparently, but when connecting the client to the repeater (instead of access point) I can't get internet access. although i do get access to the repeater setup.and access point setup too.. or if that is the fact that repeaters must be connected to a router, not access point? should I use it as a WDS? or AP-wds? I have a Cisco Lynksys e1200 router (which i'm using as access point) and an Encore ENXWI-1AN45 3 in one range extender?
View 2 Replies
View Related
Dec 11, 2011
How do you set up a linksys routers internet configuration type to public/bridge mode? my model is WRT45g
View 1 Replies
View Related
Sep 6, 2011
I have spent most of the weekend trying to get this router to act as a proper Access Point.
When it does work (Stay connected) speeds and latency are rotten. If I go back to Routing Mode this thing kicks butt, but I isolate all devices attached to a different subnet and trying to set up proper routes has proved imposable. Firmware 1.0.2 r 13
The online help stated to connect to the "internet interface" when in Bridge Mode DHCP Server Is not broadcasting to on the wireless or wired interfaces.
If I used the wired interface as the uplink I can broadcast the DHCP to any device on wired but again nothing to the Wireless. When I "Show Routing Table" I see two static routes pointing to the ATT router for the Wired/Wireless Interfaces.. 0.0.0.0 255.255.255.0 (my Gateway) Wired/Wireless (my Gateway) 255.255.255.0 0.0.0. Wired/Wireless
AP mode should only be working in Broadcast. By connecting the Wired Interfaces alone up to my switched network should not use the router at all. If you force all traffic to my router all traffic has to be inspected by the firewall You create a bottleneck my router interface is 10/100.
ATT 2 Wire Gateway/Router with pinholes. 10/100/1000 Non managed 24 port Switch Network. Server infrastructure serving DNS/DHCP.
I decided to buy this after reading it offered Bridge/Access Point mode instead of getting the WAP610 because I wanted to have the option to change to routing mode or AP mode. Since my ATT Uverse Router Wireless is “g” it takes forever to transfer files to and from my servers.
View 4 Replies
View Related
