Cisco Switching/Routing :: Configure PPPoE On 831 Router With Modem In Bridge Mode

Sep 7, 2012

config to setup PPPoE on the cisco 831 router to be used with a modem in bridge mode. I have tired other peoples configs found on the web but, not all the commands were available on the IOS version thats on the router. Also note that I bought this as a used router and I dont have a service contract so I am unable to download an updated IOS. The router ver is 12.3(7)T9 and the IOS is c831-k9o3sy6-mz.123-7.T9.bin. Running config below is last tried still could not connect or get ip address from isp. [code]

View 2 Replies


ADVERTISEMENT

Linksys Wireless Router :: WRT120N / PPPoE - Bridge Modem And Connect To Internet

Dec 6, 2011

I recently changed my internet connection to DSL from Cable, so now I'm using PPPoE type of connection.
 
Right now my router is configured as Automatic DHCP with the modem doing the PPPoE connection. All is fine and well.
 
Since I own a PS3, and Nat Type 3 conection is really bad for my online gaming, I would like to bridge my modem and connect to the internet through my router. That way I can properly forward my ports, use QoS and effectively get a better connection on the PS3.
 
I was able to successfully bridge the modem, but the PPPoE config on the router isn't able to connect to the internet.
 
Modem and router have been reinitialized after the configurations were changed. I do have the username and passwords, and they were properly put on the router.

View 1 Replies View Related

WRT54G - Put Router / Modem In Bridge Mode And Use Different One?

Aug 29, 2011

I have an SMCD3GN (from Rogers) that is both a Modem and a Router. I also have a Linksys WRT54G router that I used to use before. The SMC is giving me a lot of problems. The connection is really bad often and my internet speed drops for no reason all of a sudden. I'm getting fed up and want my old router back.

I know it's possible to change the SMC into a modem (put it in bridge mode) and then connect my router and use the Linksys router instead of the SMC. The problem is, I don't know exactly how to set it up and would really like an explanation. I already know how to get into the SMC and Linksys settings as an admin.

View 1 Replies View Related

Cisco WAN :: 5505 PPPOE Access Via VDSL Bridge Modem?

Apr 25, 2013

I just bought a 5505 to learn from and am trying to attach my VDSL modem as a transparent bridge.It goes....

Laptop   >>> (VLAN1) Cisco 5505 (VLAN2)  >>> VDSL modem >>> internet
X.X.X.10 >>> (X.X.X.254) ------ (Y.Y.Y.254)    >>> Y.Y.Y.10        >>> A.B.C.D.
  
I'm using the ASDM, if I configure VLAN2 with the IP address of the VDSL interface I can ping the modem from the console session via Putty. If I take that off and configure up the PPPOE client I can't ping the VDSL modem, I'd expect that. If I then add in an IP address to the PPPOE client config like I assigned to VLAN2 it doesn't ping either.If I can't ping the VDSL modem I don't expect it would work but it seems I can only either give it a static address which pings but has no pppoe or give it a PPPOE config which means I can't ping the VDSL. why I can't ping the VDSL modem when the interface is set as PPPOE with an IP address?Presumably if I'm on the ASA console doing pings from there to the modem then I'm ruling out problems with the routing from the laptop (trying to isolate where the issue is)

View 3 Replies View Related

Linksys Wireless Router :: EA6500 When Connect PC Directly To Modem / Configure PPPoE Connection

Mar 8, 2013

I have rather huge connection at home. DL speed 80Mb, UL speed 3Mb.When I connect my PC directly to modem and configure PPPoE connection, I get 81Mbits/sec. When I connect my old ASMAX $30 router, I get 78 Mbit/sek. And I find it OK.But when I connect my EA6500 I get 28 MBits/sec. Same result on wire as on wireless connection. Of course If I enable prioritisation, I get even less, 12-15 Mbits/sec.I tried already even configuration with ASMAX as wired router and EA6500 connected to its LAN port. It gives me 50Mbits/sec.

View 5 Replies View Related

Linksys Wireless Router :: How To Configure E2500 In Wired Bridge Mode

Jan 25, 2012

My client has a DSL modem and a Belkin wired 4-port router configured to connect to it using PPPoE.  Apparently there is no way to configure the E2500 such that it may be dropped in as a direct replacement for the Belkin (which would also provide wireless access) without the PPPoE login/password (from the DSL provider, Verizon).
 
I would like to connect the "Internet" port of the E2500 to one of the Belkin's 4 ports, in order to use the E2500 for wireless internet access without using any of the 4 wired ports but I think this creates a NAT within an existing NAT network? 
 
To avoid that if I configure the E2500 in wired bridge mode, it becomes transparent, and I can no longer access its administration interface using the address 192.168.1.1 (since that address belongs to the Belkin).  How may I, for example, change the wireless password which the E2500 is in wired bridge mode?

View 1 Replies View Related

Linksys Wireless Router :: E4200 - DSL Modem In Bridge Mode Reports Full Speed

Dec 21, 2011

I have a d-link dsl modem that reports it's getting the full 6 meg download speed from AT&T.   I put the dsl modem in bridge mode so the E4200 will do the logon to AT&T with my credentials.   If i do a speed check using CNET internet speed test, from both a desktop (wired 1gb card) and any laptop in the house (all draft n 2.4 or 5.0), it ranges anywhere from 3 meg to 4.3 meg.   I have 6 cat-e ethernet cords everywhere.   I do have 2 switches but have tried to unplug those to see if any difference

View 1 Replies View Related

Cisco Switching/Routing :: 6513 Brought Down By Bridge Mode On NIC

Mar 29, 2012

We have a 6513 with about 8 switches in it. I installed a Intel Pro PT NIC in a Dell PE2850 and setup the Team setting which created a bridge in the network connections.
 
10 minutes later, every server connected on that 'blade' went down and rebooted.
 
This happened once before to another tech here (I didn't know at the time it would do this but after he saw it he pointed it out)

View 2 Replies View Related

TWC Modem - Enable Bridge Mode

Dec 14, 2010

I have a TWC wideband modem and service. I know that they will enable bridge mode if I ask them. My questions are. After they enable it whats my setup? Do I just run a cable from their modem into a new router that I then set up on my own? Is it that simple?

View 2 Replies View Related

Cisco Routers :: Put The SRP 527 Into Bridge Mode To Use It Just As A Modem?

Mar 20, 2011

Is it possible to put the SRP 527 into Bridge mode to use it just as a modem?

View 6 Replies View Related

Cisco Firewall :: Possible To Configure Bridge Mode In ASA5505

Aug 1, 2011

Is it possible to configure bridge mode in asa 5505 if it is can u provide me a config.

View 1 Replies View Related

Cisco Wireless :: Configure A 1552 AP Over CLI To Bridge Mode

May 26, 2013

a customer got an 1552 outdoor AP in local mode and installed it at a building. It has to run as a Mesh AP (MAP). Now the AP connects one time to the WLC 5508 and started a download. After that, the AP never came back. Like we saw on the other installed 1552 RAP's, they all where in local mode.We configured all AP's to bridge mode, but the MAP could not join anymore.Is there a CLI command to change the mode on the AP itself?From the WLC it's not a problem, but for the AP CLI I cannot find sth.

View 1 Replies View Related

Cisco Wireless :: Configure Two AP WAP4410N In Bridge Mode?

Jun 16, 2011

I want to configure two AP WAP4410N  in Bridge Mode and I don´t find the correct configuraction tips.

View 11 Replies View Related

D-Link DIR-655 :: Modem Running In Bridge Mode

Jan 15, 2013

 I currently have frontier dsl internet and am using the isp provided modem/router combo and a DIR-655. I have the modem running in bridge mode and the 655 set to PPPoe connection, MTU at 1492. I confirmed the MTU setting on the isp modem/router before bridging it. The question i have is if the router MTU is set to 1492 does everything on the LAN side of the router run at 1492 or does it run at 1500 while the router breaks the packets up? Everything works fine but my pc's all use vista and i'm not sure where to check the mtu settings at and all my game consoles are set to mtu automatic so i can't really see what they're running at either.

View 7 Replies View Related

D-Link DIR-601 :: Configure In Bridge Mode As An Access Point?

Aug 23, 2011

My apartment already has internet provided to all of the rooms, but I'm trying to set up my router as a wireless access point. I tried disabling DHCP on the router, but then I wasn't able to get any internet access at all. Does this device not support bridge mode?

View 5 Replies View Related

Cisco Firewall :: Configure ASA 5520 In Transparent Bridge Mode

Sep 20, 2012

I am new to cisco ASA. I need to configure ASA 5520 in transparent bridge mode. [code] I need to place the new asa firewall in transparent mode. How to configure the firewall in transparent bridgmode.

View 5 Replies View Related

Cisco WAN :: ASA 5505 - Configure C877 In Half-bridge Mode?

Feb 16, 2011

I want to achieve the following setup:
  
So basically I have a C877 and a Cisco ASA 5505 and I want to push the public IP of the ISP to the outside interface of the ASA so the Cisco 877 will only be responsible for ADSL and PPPoA. Don't ask me why I don' t use a modem/router instead. I know that is a waste to use the C877 in this way but I want to test the setup.
 
Right now the config of the C877 regarding ADSL and PPPoA looks like that ( I don't have the ASA connected yet, so all the PC are connected directly to the C877 right now):
 
interface ATM0 no ip address load-interval 30 no atm ilmi-keepalive pvc 0/35   encapsulation aal5mux ppp dialer  dialer pool-member 1
 
interface Dialer1 ip address x.x.x.x 255.255.255.248 ip access-group OUTSIDEACL in ip nat outside ip inspect FWRule out ip virtual-reassembly encapsulation ppp dialer pool 1 ppp authentication chap pap callin ppp chap hostname xxxxxxx ppp chap password 0 xxxxxxx ppp pap sent-username xxxxxx password 0 xxxxxxx
 
ip route 0.0.0.0 0.0.0.0 dialer 1
 
ip nat inside source route-map Nat interface Dialer1 overload
 
interface vlan 100 is my LAN configured with DHCP.
 
how I should configure the C877 to push the public IP to the ASA?

View 6 Replies View Related

Cisco WAN :: 2821 - Configure Router To Use 2 ADSL Lines With Dialer And Modem In RFC2684 Mode?

Mar 9, 2011

I want to configure my router to use 2 ADSL lines each with a dialer and a modem in RFC2684 mode. I have a 2821 (IOS 12.4) with an HWIC-4ESW.
 
My network topology is like this :

ADSL Modem 1 (RFC2684) --
(Fa0/0/0)
Router -- (Gi0/1) MyLAN
(Fa0/0/1)
ADSL Modem 2 (RFC2684) --/
 
1. I configure my DSL Modem in RFC 2684. The first use 172.16.0.2/29 and the second 172.16.0.3/29. I connect this devices to Fa0/0/0 and Fa0/0/1.
 
2. I configure Vlan1 to use the network configured on my modem :

interface Vlan1
ip address 172.16.0.1 255.255.255.248
 
3. I try to ping my devices :

#ping 172.16.0.2
 Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.0.3, timeout is 2 seconds:
!!!!!

[code]....

View 3 Replies View Related

Linksys Cable / DSL :: How To Configure WAG200G To Work In Bridge Mode

Apr 21, 2007

I'm trying to configure my WAG200G to work in bridge mode so that it can transfer my external IP address to my ISA server.My network map is very simple,Internet -- WAG200G -- ISA Server -- LANCan

View 7 Replies View Related

Cisco Routers :: RV120W / Configure Bridge Mode For Internet Access?

Jan 1, 2013

We have a RV120W Wireless-N VPN Firewall and we want to configure the router in brigde mode (transparent). Because we have another Firewall, use for filtering and default gateway on the LAN. The ISP provide IP address by DHCP, so we must connect the internet connexion to the WAN interface. But How can we do for connected the RV120W to our firewall? The router mode on the RV120w allows-it to make this configuration?

View 1 Replies View Related

PPPoE Bridge In Router And Giving Firewall A Public IP?

Jan 5, 2013

I have 2 public ip, 1.1.1.1 anda 1.1.1.2. I'm connected to the ISP using PPPoE. I also have a router and a firewall. I want to assign 1.1.1.1 to router and 1.1.1.2 to the firewall. I do not want to NAT 2 times (one in router and one in firewall)That's why i want to bridge Fa0/0 and Fa0/1.Could this be done in Cisco router? I've done this command but it's not working as i want. I'm using bridge irb and bridge-group.

View 6 Replies View Related

Configure Tplink Modem On Repeater Mode In Order To Repeat Signal From (Huawei)?

Dec 4, 2011

That's y topology:

(TPLINK) /////////////// (Huawei)--->(internet)
...................wirless................cable

I want to configure my tplink modem on a repeater mode in order to repeat the signal from (Huawei) ...

View 1 Replies View Related

Linksys Wireless Router :: WRT54GS Factory Defaults / Resetting Connection Type From PPPoE To Bridge

Jan 17, 2012

I'm having a very difficult time getting my WRT54GS to work with my Westell 6100 modem. I've been bouncing around gathering info, and what I've learned is that the goofy way CenturyLink tech support told me to hook up my old wired router (modem line into outgoing (LAN) router port) is because the Westell 6100 is a "smart modem/router". Therefore, when I run the Linksys setup CD, it sees the modem as a router, and won't properly configure. I've also learned that the Westell modem can be "dumbed down" into simply a modem by putting it into "bridge mode", which is where I'm at right now - trying to get it reset to factory defaults and resetting the connection type from PPPoE to Bridge. In the meantime, I also reset the WRT54GS to factory defaults, and now I've got another problem: the router will not allow me to set up encryption. The default setting is "Disabled", and when I click the down arrow and try to make any selection at all (preferred selection is WPA2 Personal), it reverts to Disabled. I've also tried to change the router's IP address to 192.168.2.1 (and alternately to 192.168.1.253), so it won't conflict with the modem's IP, and it freezes up every time I try.

View 2 Replies View Related

Cisco WAN :: Configure Router 1801 With PPPOE

Jun 10, 2012

 when I'm trying to configure my router 1801 with PPPOE  I have the message below "% PPPoE config from vpdn-group is converted to pppoe-profile based config.% Continue PPPoE configuration under 'bba-group pppoe global'.

View 3 Replies View Related

Cisco WAN :: Configure 1941 Router For PPPOE With Dynamic IP?

Dec 18, 2010

how to configure the Cisco 1941 router for PPPOE with dynamic IP

View 10 Replies View Related

Linksys WRT54G Router / Configure A Repeater For A PPPoE Connection?

May 3, 2011

I am using a PPPoE connection using a linksys WRT54G router (working perfectly) and am now trying to set up an Edimax EW-7206APg to extend my wireless connection range. I followed the instructions given on the Edimax manual, and while my devices (iPad, laptop) got connected to the new repeater network, I could not access the Internet from it. I may be wrong, but the instructions on the Edimax manual seemed to be for a DHCP connection. Is there anything different I need to do to configure the Edimax repeater on a PPPoE connection?My router IP ("Local IP address") shows 10.10.0.1 instead of the "192.168.1.1" that all the documentation online seems to suggest.

View 6 Replies View Related

Linksys Wireless Router :: Configure Pppoe On WRT120N It Say It's Connected But Cannot Access Wan

Aug 11, 2010

I have configure pppoe on my WRT120N it say it's connected but cannot access wan side of the router.

View 5 Replies View Related

Linksys Wireless Router :: WRT54G2 V1 - Access PPPoE Modem With Wired Ethernet?

Oct 13, 2011

I am using the WRT54G2 connected to a cable modem that requires a PPPoE login.  I followed the Service Providers instructions and cloned the modems MAC address to the WRT54G and setup the PPPoE user id and password.  I can then plug my PC into one of the Ethernet connections on the back of the WRT54G and everything works as expected.  First I connect to the WRT54G2 and then I open a PPPoE connection in my network settings and it logs into the service provider and everything works as expected.  But when I connect to the WRT5G2 wirelessly I connect to the AP fine.  When I open the same PPPoE connection to the service provider it fails, the message says I have the wrong userid or password or that the protocol is not supported.  Of course I know the userid and password is correct because it works when connected with Ethernet cable.  I have tried disabling the security on the wireless network but that did not seem to work.The modem is a HomePNA HCNA Voice Endpoint.I am at the latest firmware 1.0.04.

View 7 Replies View Related

TP-Link 3G/3.75G Router :: TL-MR3220 - How To Set Bridge Mode

Dec 25, 2012

Region : Italy
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.12.20 Build 120705 Rel.39030n Beta
ISP :

I'm facing problem to properly set BRIDGE mode (WDS Bridging). I had a router connected to ADSL line with following setting:

IP 192.168.1.1
Security setting - WPA2/TKIP
DHCP on

The wi-fi coverage is not good in all the floor so I'm trying to extend coverage using a TL-MR3220. I did follow the instruction in this video [url]....

View 3 Replies View Related

Linksys Wireless Router :: Using E4200 In Bridge Mode?

May 1, 2012

I have a E4200 with 1.0.04 firmware that I've used for a while as a router in front of a cable modem. I have upgraded the modem to a Virgin Media SuperHub. I have connected my E4200's WAN port to one of the SuperHub's LAN ports and changed the E4200's mode to Bridged Mode.I can connect to the Internet wirelessly and wired on the SuperHub, but I can only connect to the Internet via the E4200 if I'm wired to it. The wireless will connect to the E4200, it gets allocated and IP address in the correct range and the gateway is shown as the SuperHub's IP address, and I can see the E4200's management website via wireless, but I cannot connect to anything beyond the E4200.

View 9 Replies View Related

Linksys Wireless Router :: Using EA3500 In Bridge Mode?

Feb 16, 2013

I bought the EA3500 nine months ago mainly for the USB port (for a NAS). I recently replaced Comcast Cable with Verizon FIOS. So I now have the FIOS router as my main router (its' IP address is 192.168.1.1). I put the EA3500 in bridge mode to extend the (wired) network. I could get: After going in to bridge mode (with DHCP), I can not log in to the EA3500 (IP address 192.168.1.5 assigned by the FIOS router). I connect my computer directly to one of  the EA3500 numbered ports (after various combinations of rebooting EA3500 and rebooting PC). It just continues to say "waiting" and never logs in. Tried choosing a static route (tried both 192.168.1.43 and 192.168.1.5 with 255.255.255.0, gateway and DNS1 = 192.168.1.1) with no luck.Since I can't log in, I cannot set up my NAS on the USB port of the EA3500 (so I haven't gotten far enough to determine if the USB port will even work in bridge mode).Thought about ensuring the latest firmware but since I can't log in I can't do that. (And after a hard reset EA3500 IP address is 192.168.1.1 which creates conflict with FIOS)

View 9 Replies View Related

Linksys Wireless Router :: E4200 Possible To Put It Into Bridge Mode

Sep 26, 2011

As I understand, the latest FW for the E4200 makes it possible to put he router into bridge mode. In this mode, I can use it as an access point. In bridge mode, should I then connect my router to the WAN port at the E4200?The other way to make the E4200 into an AP, is to disable DHCP and NAT and give the E4200 an IP address out of range for the DHCP range in my preferred router.

Choosing between this two option to make the E4200 into an AP, which is considered to be the best solution?And to be sure; using this option, then the Ethernet cable should be connected to the LAN port of the E4200? is the performance of an E4200 in AP mode the same as a dedicated AP like the WAP610N?

View 3 Replies View Related

Linksys Wireless Router :: E4200 In Bridge Mode

Aug 20, 2011

Just bought 2 e4200's!  I have the first one connected to the ATT router, and I have the second one connected to the first in Bridge Mode.  It works great! It knew how to configure itself to be the down-level client.
 
However, I noticed that the port speed is only 100 Mbps on the port that is acting as the link for the bridge.  I am running brand-new CAT5e thru the house, and if I connect the cable directly to my laptop - I get 1Gbps. So I know that the cable is good.
 
Is there a way to change the speed of the INET port on the down-level e4200? 

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved