Linksys WRT54G Router / Configure A Repeater For A PPPoE Connection?
May 3, 2011
I am using a PPPoE connection using a linksys WRT54G router (working perfectly) and am now trying to set up an Edimax EW-7206APg to extend my wireless connection range. I followed the instructions given on the Edimax manual, and while my devices (iPad, laptop) got connected to the new repeater network, I could not access the Internet from it. I may be wrong, but the instructions on the Edimax manual seemed to be for a DHCP connection. Is there anything different I need to do to configure the Edimax repeater on a PPPoE connection?My router IP ("Local IP address") shows 10.10.0.1 instead of the "192.168.1.1" that all the documentation online seems to suggest.
View 6 Replies
ADVERTISEMENT
Jan 2, 2013
Is it possible to configure the WRT54G as a repeater signal of the WRT120N?
View 1 Replies
View Related
May 3, 2011
I am using a PPPoE connection on a linksys WRT54G router and trying to set up an Edimax EW-7206APg to extend my wireless connection range.I followed the instructions given on the Edimax manual, but that seems to be for a DHCP connection. Is there anything different I need to do to configure the Edimax repeater on a PPPoE connectionMy router IP ("Local IP address") shows 10.10.0.1 instead of the "192.168.1.1" that all the documentation online seems to suggest. What am I doing wrong?
View 2 Replies
View Related
Mar 8, 2013
I have rather huge connection at home. DL speed 80Mb, UL speed 3Mb.When I connect my PC directly to modem and configure PPPoE connection, I get 81Mbits/sec. When I connect my old ASMAX $30 router, I get 78 Mbit/sek. And I find it OK.But when I connect my EA6500 I get 28 MBits/sec. Same result on wire as on wireless connection. Of course If I enable prioritisation, I get even less, 12-15 Mbits/sec.I tried already even configuration with ASMAX as wired router and EA6500 connected to its LAN port. It gives me 50Mbits/sec.
View 5 Replies
View Related
Jan 9, 2011
When it comes to configuring my new Linksys Cisco WRT120N router to my PPPoE connection. I've visited 192.168.1.1 but I'm not sure what to do next. So, I've got a PPPoE connection, static IP address, Linksys Cisco WRT120N router and a terrible ISP.
How to configure my new router so that I can start using the wireless for Internet access at home.
View 3 Replies
View Related
Dec 21, 2012
Every night I turn everything off via power strip, including the router. Before I turn off the router, my roku connection is good.In the morning, the roku will work for about 20 minutes, then disconnects, and then I'm unable to find the router.I'll then need to reset my router's settings (I have the WRT54GS), and then uplug, and replug the router.It's important that I unplug the router every night.Is there a way to configure the settings so I don't have to reconfigure the settings every morning?
View 4 Replies
View Related
Jul 27, 2011
I have a linksys wrt54g v2 router I want to convert to a repeater. I looked up instructions buteveryone says after all is done I have to connect my main router to the new configured rrepeater. Is there.a way I can do this without connectingthem together via cable. My house is seperate from the main house and running cable is not logical I have signal at my house just need better signal
View 1 Replies
View Related
Nov 30, 2011
is it any possibility to set my router WRT54G V2.2 as a wireless repeater? and does any manual for this exist?
View 3 Replies
View Related
Aug 11, 2010
I have configure pppoe on my WRT120N it say it's connected but cannot access wan side of the router.
View 5 Replies
View Related
Mar 27, 2012
I'm trying to configure an 887VA for a pppoe ADSL2+ connection with no luck.I know the ISP requires pppoe (LLC), and the pvc is 8/35.
The CD light is on, and the line is up, but the 887 just won't connect
View 3 Replies
View Related
Oct 20, 2012
I would like to use my new EA6500 as the base station and another wireless router with Wireless Repeating Function as a repeater. Is the EA6500 capable of that?? I have not found any documentation on that subject.
View 6 Replies
View Related
Feb 24, 2012
I recently purchased a Linksys E1200 to replace my Linksys WRT54G. I'd like to utilize the WRT54G as a repeater. Is this possible, or do I need to buy a "repeater"? how to configure/set up the WRT54G repeater?
View 3 Replies
View Related
Dec 28, 2012
Is it possible to configure a E2500 as router and WAP54G as a repeater? I used to have a WRT54GS as router but it has broken and now I bought a E2500 to replace it.
View 2 Replies
View Related
Jun 22, 2010
I'm very dissatisfied with the range and signal strength of my new WRT610N dual band router compared to the WAP54G Access Point I used before.Can I configure the Access Point as a repeater for the 2.4 GHz band on the WRT610N if I use the WRT610N as a Wireless G router rather than wireless N?
View 5 Replies
View Related
Sep 27, 2012
My WRT54G Linksys router works with wifi and local connection but it wont let me configure to change it to PPpoe nor wont let me enable a wireless connection, so it's open to the public how do i get it to open it resetting it and holding the button on the router for 30 secs.
View 1 Replies
View Related
Jul 22, 2008
I have WRTG54G with 4ports and a internet port, i have a zoom adsl modemfor DSL i wants to share DSL connection with internet port on WRTG54G but i d'nt know how to do this
View 5 Replies
View Related
Nov 29, 2012
I recently buyed a Linksys EA6500 wireless router. I accessed [URL] to access the settings interface of the router. Went to "Connectivity Internet Settings" and chose type of the internet connection as PPPoE. Entered the username and password, clicked ok.
No internet access.
View 9 Replies
View Related
Mar 6, 2012
I want to share PC internet (PPPOE connection) on my linksys wireless router (E3000)Problem : When i directly connect internet wire in router, pppoe connection frequently gets disconnected. So what i wanted was to share my pc internet on router.I have two lan card on windows 7 installed PC, 1st lan card is connected to internet cable and i can access internet on pc, second lancard is connected to wireless router. So basically what i want is to share pc internet ( PPPOE ) on wireless router through DHCP connection type.
View 1 Replies
View Related
Jul 8, 2011
I've downloaded the driver for a tenda usb adapter. What else do I need to do to connect to the WRT54G network? I'm currently connected via an ethernet cable. Running Windows/7.
View 1 Replies
View Related
Dec 26, 2011
I recently set up a wrt54g router that I got used from a friend. I pressed the 'reset' button on the back, configured it for my computer according to the instructions on the website, and everything worked fine for a couple of days. Then I lost connectivity, tried powercycling my modem, but had to reset and reconfigure the router again. Worked fine again for a couple of days, then the problem repeated itself, so I reset and reconfigured again.
View 1 Replies
View Related
Jan 17, 2013
Used an E4200 version 1 to terminate PPPoE on a really high speed connection? By that I'm talking say 400Mb or higher.
View 9 Replies
View Related
Jan 17, 2012
I'm having a very difficult time getting my WRT54GS to work with my Westell 6100 modem. I've been bouncing around gathering info, and what I've learned is that the goofy way CenturyLink tech support told me to hook up my old wired router (modem line into outgoing (LAN) router port) is because the Westell 6100 is a "smart modem/router". Therefore, when I run the Linksys setup CD, it sees the modem as a router, and won't properly configure. I've also learned that the Westell modem can be "dumbed down" into simply a modem by putting it into "bridge mode", which is where I'm at right now - trying to get it reset to factory defaults and resetting the connection type from PPPoE to Bridge. In the meantime, I also reset the WRT54GS to factory defaults, and now I've got another problem: the router will not allow me to set up encryption. The default setting is "Disabled", and when I click the down arrow and try to make any selection at all (preferred selection is WPA2 Personal), it reverts to Disabled. I've also tried to change the router's IP address to 192.168.2.1 (and alternately to 192.168.1.253), so it won't conflict with the modem's IP, and it freezes up every time I try.
View 2 Replies
View Related
Mar 20, 2012
I am in a situation where I share internet access with roommates. We have a Gateway which is conected to the provider and which delivers ethernet and WiFi signal.
In order to isolate myself from my roomates and to protect my network connection, both wired and WiFi, I would like to plug in the Ethernet cable I get from the Gateway to my router, and then configure my router's firewall and WiFi enctryption to maximize my safety.
However, I am having some problems. I have already configured the router as "router" and not "Gateway" and I am trying to assign it an IP address different from the default one, which is the one the gateway has, and a ranger of DHCP IP's, also different from those of the Gateway. In other words, 192.1681.N.1 for the router and start from there.
View 9 Replies
View Related
Jun 10, 2012
when I'm trying to configure my router 1801 with PPPOE I have the message below "% PPPoE config from vpdn-group is converted to pppoe-profile based config.% Continue PPPoE configuration under 'bba-group pppoe global'.
View 3 Replies
View Related
Nov 20, 2011
I have two DIR-615 devices, I want use first device for main AP and DHCP server and PPPoE . And use second device for Repeater.
How to work WPS and Push button on this device.
View 6 Replies
View Related
Dec 18, 2010
how to configure the Cisco 1941 router for PPPOE with dynamic IP
View 10 Replies
View Related
May 14, 2012
I have here a canyon wireless router. do you know where I can find online a tutorial or manual on how to configure a wireless router so that it acts as a repeater?
View 3 Replies
View Related
Sep 7, 2012
config to setup PPPoE on the cisco 831 router to be used with a modem in bridge mode. I have tired other peoples configs found on the web but, not all the commands were available on the IOS version thats on the router. Also note that I bought this as a used router and I dont have a service contract so I am unable to download an updated IOS. The router ver is 12.3(7)T9 and the IOS is c831-k9o3sy6-mz.123-7.T9.bin. Running config below is last tried still could not connect or get ip address from isp. [code]
View 2 Replies
View Related
Jan 12, 2012
I'm trying to set up my sons I pod touch to my router i have the wrt54g v6 and it won't connect?
View 7 Replies
View Related
Feb 19, 2013
Situation: I have one Internet connection and I have need of two networks. One filtered with OpenDNS and the other unfiltered. I have a Speedstream DSL router provided by ISP for connecting to Internet. I have two WRT54G's and would like to utilize them to form two networks. The Speedstream is a router with a gateway address of 192.168.1.254.
From that Speedstream (only one network plug) I would like to go to a 5port switch. From that switch, I would like to configure the two WRT's to be two different networks (one using OpenDNS settings for filtering) with one having a 192.168.1.x address scheme and the other (no Internet filtering) having a 192.168.10.x scheme. Both would have DHCP enabled for their networks and the Speedstream would have DHCP disabled. There is not a need (at this point) to have the networks communicate.
View 1 Replies
View Related
Jan 20, 2012
Ive had a WRT54G v5 for awhile now. And just recently I went out of town and had turn off my router. When coming back and turning everything back on for some reason both wired and wireless components both have a connection then it loses the connection for awhile and comes back on. Ive power cycled both the router and modem. Called my provider and they said it was my router after doing some diagnostic tests. I tried to update the firmware and ive tried to restore to factory settings. Still it has a connection then it loses it.. Ive noticed on the modem when its not working that only the SENT light is flashing. (modem has power,received,sent, cable,pc). It is on AUTO DHCP and gets a ip and everything.
View 1 Replies
View Related
Mar 1, 2012
I can connect to the internet just fine if I run my modem straight to my computer. If I try to run it through my router, however, I can't get a connection. The internet light on the router does not light up and shows no signs of connection. The DHCP renewal doesn't do anything, either. I have power cycled many, many times and reset the router to factory settings as well. I have tried cloning the mac address to match the computer and done all that I can (as far as my knowledge reaches). The tech support 'warranty' is also outdated, so there are no other options except for paying a ridiculous amount of money to talk to somebody.I just got a new modem yesterday and that is when it stopped working through the router. This problem occurs with two different routers (both of which worked previously) so I don't think anything is faulty.The modem is an ARRIS TM602G and the router is a Linksys WRT54G v.3
==================
MODEM (WITHOUT ROUTER)
==================
Host Name . . . . . . . . . . . . : Steez-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
[code]....
View 3 Replies
View Related
Mar 1, 2012
I can connect to the internet just fine if I run my modem straight to my computer. If I try to run it through my router, however, I can't get a connection. The internet light on the router does not light up and shows no signs of connection. The DHCP renewal doesn't do anything, either. I have tried multiple 'solutions' and am completely stumped.I have power cycled many, many times and reset the router to factory settings as well.I have tried cloning the mac address to match the computer and done all that I can (as far as my knowledge reaches). The tech support 'warranty' is also outdated, so there are no other options except for paying a ridiculous amount of money to talk to somebody.
View 1 Replies
View Related
