I have WRTG54G with 4ports and a internet port, i have a zoom adsl modemfor DSL i wants to share DSL connection with internet port on WRTG54G but i d'nt know how to do this
View 5 RepliesI've downloaded the driver for a tenda usb adapter. What else do I need to do to connect to the WRT54G network? I'm currently connected via an ethernet cable. Running Windows/7.
View 1 Replies View RelatedJust had Verizon FIOS  service installed. It comes with an actiontec modem. I would like to remove the actiontec modem and connect directly to my Linksys RT31P2 which is cascaded to my Linksys WRT54G. I have tried just about every router setup config; all with no success. How to be able to connect the FIOS directly to a linksys router.
View 3 Replies View RelatedI am trying to get wireless internet set up again and have run into a big issue. Previous wireless router was also a WRT54G and she had problems. I gave her my old one that I was no longer using, but it was still working with no problems.
Â
The problem that I am having is that we are unable to get internet through the wireless router. We are able to get the desktop connected to the internet when we plug it directly into the DSL modem, but when we plug the wireless modem into the DSL modem and the desktop into the wireless modem, then we don't get any internet connection at all.
Â
I had her do a factory reset on modem so that we were starting fresh. I have also tried unplugging both modems and then pluggin in the DSL and then Wireless modem, with no change. We have the ability to get into wireless settings page, but I'm not sure what in there to change that would make any difference on this one.
Â
I know that this problem isn't actually a wireless problem, but it has to be related to the modem. We haven't even been able to get to the wireless part of the set up and we are already running into problems.
Is it possible to configure the WRT54G as a repeater signal of the WRT120N?
View 1 Replies View RelatedI recently set up a wrt54g router that I got used from a friend. I pressed the 'reset' button on the back, configured it for my computer according to the instructions on the website, and everything worked fine for a couple of days. Then I lost connectivity, tried powercycling my modem, but had to reset and reconfigure the router again. Worked fine again for a couple of days, then the problem repeated itself, so I reset and reconfigured again.Â
View 1 Replies View RelatedI am at my wits end.Comcast just changed my old RCA cable modem for an Arris Telephony modem.(I had Comcast phone service added)The tech that did the install said the wireless G network was all up and running. (My 3 other computers and printer) Well lo and behold the network does not work at all. I only get internet through my wired computer and cannot access my router through 192.168.1.1 anymore.I tried powering down the router and modem by holding the reset for 30 seconds and unplugging them.
View 9 Replies View RelatedEvery night I turn everything off via power strip, including the router. Before I turn off the router, my roku connection is good.In the morning, the roku will work for about 20 minutes, then disconnects, and then I'm unable to find the router.I'll then need to reset my router's settings (I have the WRT54GS), and then uplug, and replug the router.It's important that I unplug the router every night.Is there a way to configure the settings so I don't have to reconfigure the settings every morning?
View 4 Replies View RelatedI am recieving error 619 (port for connection was closed) when trying to connect over my wireless connection. If I disconnect the WRT54G and hard wire to the cable modem I can VPN in without a problem. I have enabled IPSec / PPTP / L2TP on the VPN security tab and have reset the wireless modem.
View 4 Replies View RelatedI am in a situation where I share internet access with roommates. We have a Gateway which is conected to the provider and which delivers ethernet and WiFi signal.
Â
In order to isolate myself from my roomates and to protect my network connection, both wired and WiFi, I would like to plug in the Ethernet cable I get from the Gateway to my router, and then configure my router's firewall and WiFi enctryption to maximize my safety.
Â
However, I am having some problems. I have already configured the router as "router" and not "Gateway" and I am trying to assign it an IP address different from the default one, which is the one the gateway has, and a ranger of DHCP IP's, also different from those of the Gateway. In other words, 192.1681.N.1 for the router and start from there.
Setting up my wrt120n ROUTER Â for remote view.this is becos i dont have a DSL cable modem, what i have is a 3G Â usb modem.
View 1 Replies View RelatedMy WRT54G Linksys router works with wifi and local connection but it wont let me configure to change it to PPpoe nor wont let me enable a wireless connection, so it's open to the public how do i get it to open it resetting it and holding the button on the router for 30 secs.
View 1 Replies View RelatedI can connect to the internet just fine if I run my modem straight to my computer. If I try to run it through my router, however, I can't get a connection. The internet light on the router does not light up and shows no signs of connection. The DHCP renewal doesn't do anything, either. I have power cycled many, many times and reset the router to factory settings as well. I have tried cloning the mac address to match the computer and done all that I can (as far as my knowledge reaches). The tech support 'warranty' is also outdated, so there are no other options except for paying a ridiculous amount of money to talk to somebody.I just got a new modem yesterday and that is when it stopped working through the router. This problem occurs with two different routers (both of which worked previously) so I don't think anything is faulty.The modem is an ARRIS TM602G and the router is a Linksys WRT54G v.3
==================
MODEM (WITHOUT ROUTER)
==================
Host Name . . . . . . . . . . . . : Steez-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
[code]....
I can connect to the internet just fine if I run my modem straight to my computer. If I try to run it through my router, however, I can't get a connection. The internet light on the router does not light up and shows no signs of connection. The DHCP renewal doesn't do anything, either. I have tried multiple 'solutions' and am completely stumped.I have power cycled many, many times and reset the router to factory settings as well.I have tried cloning the mac address to match the computer and done all that I can (as far as my knowledge reaches). The tech support 'warranty' is also outdated, so there are no other options except for paying a ridiculous amount of money to talk to somebody.
View 1 Replies View RelatedI am using a PPPoE connection using a linksys WRT54G router (working perfectly) and am now trying to set up an Edimax EW-7206APg to extend my wireless connection range. I followed the instructions given on the Edimax manual, and while my devices (iPad, laptop) got connected to the new repeater network, I could not access the Internet from it. I may be wrong, but the instructions on the Edimax manual seemed to be for a DHCP connection. Is there anything different I need to do to configure the Edimax repeater on a PPPoE connection?My router IP ("Local IP address") shows 10.10.0.1 instead of the "192.168.1.1" that all the documentation online seems to suggest.
View 6 Replies View RelatedI have rather huge connection at home. DL speed 80Mb, UL speed 3Mb.When I connect my PC directly to modem and configure PPPoE connection, I get 81Mbits/sec. When I connect my old ASMAX $30 router, I get 78 Mbit/sek. And I find it OK.But when I connect my EA6500 I get 28 MBits/sec. Same result on wire as on wireless connection. Of course If I enable prioritisation, I get even less, 12-15 Mbits/sec.I tried already even configuration with ASMAX as wired router and EA6500 connected to its LAN port. It gives me 50Mbits/sec.
View 5 Replies View RelatedI just ordered the Linksys WAG120N modem/ router and need configuring the same on the BSNL network. Any Document or link about his Installation and configuration.
View 3 Replies View RelatedI don´t really have the RJ45 cable, how to configure it as an access point wirelessly? I mean,just by entering the main menu with the default ip address.
View 1 Replies View RelatedWhen I hook up the Westell modem to my Linksys router WRT54G it wont work?
View 1 Replies View RelatedI have an SMCD3GN (from Rogers) that is both a Modem and a Router. I also have a Linksys WRT54G router that I used to use before. The SMC is giving me a lot of problems. The connection is really bad often and my internet speed drops for no reason all of a sudden. I'm getting fed up and want my old router back.
I know it's possible to change the SMC into a modem (put it in bridge mode) and then connect my router and use the Linksys router instead of the SMC. The problem is, I don't know exactly how to set it up and would really like an explanation. I already know how to get into the SMC and Linksys settings as an admin.
I have WAG120N and is working fine, but has very poor wifi range. I recently purchased EA 6500. how to setup my WAG120N as a modem only and shift all routing to the EA6500
View 2 Replies View RelatedI'm looking to upgrade my WRT54G as I have had NO luck in getting my Galaxy Tab to connect through it so far (can connect and get an IP address but can't get out to the web) and have had intermittent problems with my Blu-ray lately. Â I am looking for something with the best affordable range, live 3 floors down from the current one and get about 3/4 signal strength so there's not much interference it seems. Â I watch a lot of online content through Hulu, Netflix, and LMB games and share with 2 other people.I am looking at the E series, probably the E1200, 1500 or 1550 as they seem to meet my needs. Â Any users have any advice about the ease of install and use of either of these? Â Or would it be better to get a gateway as we are considering going from DSL to U-verse service, twice the speed for $2/month more
View 6 Replies View Relatedi got this wireless router (linksys version WRT54G) from my aunt but she can't find the disc for it. is there a way to use it without buying anything (this is mainly for my wii), if so how?
View 2 Replies View RelatedI have an old wireless router lying behind me and I want to use that old router as a switch. That old router is a knock-off,no-name router brand called "Gigafast" and the model number is WF19-CAPR. There are also variants to that router name as well.The router that I currently have is a Linksys WRT54G wireless-G router. I'm planning to upgrade the wireless router in favor of Wireless-N in the near future.I want to know how can I use that particular Gigafast router as a switch and I want to link that router up to my WRT54G router. The scenario goes as follows:
Cable internet connection ----> WRT54G router ---> Gigafast router (as a switch)
The IP address for the WRT54G router is 192.168.1.1, while the Gigafast router is 192.168.1.254. I may know by now that I have to disable DHCP on the gigafast router and I have to change an IP address to something that is "not in range" with the WRT54G router, am I right?I want to expand the number of ports, so I can connect with future devices such as a VoIP ATA adapter, a laptop and possibly an entertainment box (i.e. Apple TV or Boxee box)
I have lost the start-up cd for my router, where to find a downloadable one so i can hook up my router.
View 1 Replies View Relatedhave one router WRT54G with firmware version v2.02.7, Feb. 27, 2004, and I'm trying to use this router to get my PS3 connected to the internet, but in the PS3 appears that I'm using NAT Type 3 and to enable some online features in my PS3 I must change it to NAT Type 2 (from the router configuration), I tried everything that I found (put my PS3 in DMZ zone, enabling TCP/UDP ports, enabling/disabling UPnP, disabling Media Server Connections in my PS3, etc.) and nothing works,
View 3 Replies View RelatedOur office has 2 connections to the internet. Each connection comes into our building through a Linksys WRT54G router. I like to connect the routers together through their ethernet ports so that we can share resources such as printers and etc. Should I config each router such that they are actually on the same network? For example:Router 1:Router IP 192.168.1.1DHCP serves 192.168.1.100-150Router 2:Router IP 192.168.1.2DHCP serves 192.168.151-200
View 2 Replies View RelatedI can not find the CD for my WRT54g router. Is there any place to download the setup info?
View 9 Replies View RelatedI have a WRT54G wireless router that I haven't used in years because my old cable provider supplied me with a router. I recently switched cable providers & they don't provide a wireless routers. I would like to use my WRT54G router, but I don't have the cd. I figured it wasn't a problem because I can just do a manual setup using the ip address 192.168.1.1. I receive the pop up window to enter the user name & password. I follow the instructions & just type in the password field the word admin & l left the user name blank but it doesn't work.Â
View 4 Replies View RelatedI have a few devices at my home that connect wirelessly to the internet via wrt54g. I want to connect to the internet via VPN. I would like to find out if it is possible to connect WRT54G router to the VPN via PPTP or L2TP? The VPN company provided me with PPTP and L2TP credentials. I can access vpn via OpenVPN on computers but I would like my TV connect to the internet also via VPN.
View 5 Replies View RelatedMy 'network' looks like this:
Â
CABLE MODEM ===> WRT54G
WRT54G Port1 ===> PC
Â
PC is running Windows/XP sp3 with all updates installed. It has no wireless adapter.WRT54G model number sticker shows ver.2. I don't think the firmware has ever been upgraded.This used to work. What has changed? The laptop that used to connect wireless is dead. I now have a 2nd PC that sits on the same table as the old PC. It has no wireless adapter at this point, but eventually either it, or the old computer, will be getting its internet connection wireless-ly, as the computers will be physically in separate rooms. I can't see how these changes would affect the operation of the router.
I have a WRT54G router that's worked for a very long time. I had WEP security set up and it worked fine until recently. About a week ago my three year old son managed to reset the router (I'm still not sure how). When I go onto the web-based setup page I am unable to change the wireless security setting. I select an option from the drop down menu but then the page reloads and nothing has changed.
View 1 Replies View RelatedWRT54G v6 router suddenly cuts out several times each day, using it with wired connection on two computers. No problem when direct wired to the modem. Is this router failing? How to fix it?
View 4 Replies View Related