Linksys Wireless Router :: Arris Cable Modem Not Working With WRT54G

Mar 7, 2007

I am at my wits end.Comcast just changed my old RCA cable modem for an Arris Telephony modem.(I had Comcast phone service added)The tech that did the install said the wireless G network was all up and running. (My 3 other computers and printer) Well lo and behold the network does not work at all. I only get internet through my wired computer and cannot access my router through 192.168.1.1 anymore.I tried powering down the router and modem by holding the reset for 30 seconds and unplugging them.

View 9 Replies


ADVERTISEMENT

Arris TM402P / 110 Cable Modem Randomly Stops Working

Aug 17, 2012

I am trying to figure out whats wrong with my parents apple airport router. Its connected into an Arris TM402P/110 cable modem. It randomly stops working, the network is there and shows up fine but you cant connect to it. It might work for a day or 2 and then just stops. I am trying to figure out if there is a configuration issue or the airport hardware is just failing. I am not sure where to start troubleshooting. The event log for the modem isnt much help, the following message shows up occasionally:

No Ranging Response received - T3 time-out

Whats interesting is my mom plugged her desktop right into the cable modem and then after plugging it back into the airport the wireless was working again. Is it possible there is a DHCP issue? If the hardware is failing what would be a good replacement for the airport?

View 2 Replies View Related

Linksys Wireless Router :: Can't Get Internet To WRT54G Using Arris

Nov 23, 2007

I just switched from DSL to Cable and now i can't get internet to the Linksys router. I can connect to it from a wireless laptop but just not get on the internet I've read other posts about doing the "clone mac" address and doing the power cycle but still cannot get the Linksys to respond. I enabled the WRT54G to clone the mac address and have spent about 10 hours in two days trying to get this to work and looking online, etc....

View 7 Replies View Related

Linksys Wireless Router :: Disconnect WRT54G And Hard Wire To Cable Modem

Feb 5, 2013

I am recieving error 619 (port for connection was closed) when trying to connect over my wireless connection.  If I disconnect the WRT54G and hard wire to the cable modem I can VPN in without a problem. I have enabled IPSec / PPTP / L2TP on the VPN security tab and have reset the wireless modem.

View 4 Replies View Related

Home Network :: ARRIS TM822 - Bridging Cable Broadband Modem To Router

Feb 18, 2013

i have an ARRIS TM822 cable modem provided by comcast, in addition i have a linksys e3000 wireless router. what i am trying to accomplish is to bridge the cable modem over to the router. i messaged comcast about this issue and i have attempted what they told me to do, but im not getting any where.

View 1 Replies View Related

Linksys Wireless Router :: WRT54GS With Mac OS 10.6.8 And RCN Cable Modem Not Working?

Sep 27, 2011

I have a Linksys WRT54GS, version 6 with Mac OS X (version 10.6.8) hooked up to a Scientific Atlantic cable modem, with RCN as the ISP.
 
Recently, RCN had some network issues, and so I had to power down and reset my modem. The modem is working fine now -- no problems at all when the Mac is connected direclty to the modem.
 
The router's network is OK in that I can connect the Mac wirelessly to the network, but I can't connect to the internet through the router (through neither the wireless or wired connection).
 
I have downloaded the latest firmware update for the router, following the Linksys site instructions.
 
I did call Linksys tech support on the advice of RCN, and they said that the router does appear to be working (power, WLAN, and Internet lights are on), but they would be charging me nearly the cost of a new router to fix the problem.

View 1 Replies View Related

Linksys Wireless Router :: E1000 / Arris TM502G Modem - Extremely Slow Network Speed

Aug 6, 2011

I am having a problem with my newly purchased Linksys E1000 router, I am having terribly slow network speeds while on that network.
 
Here are my network speeds with The e1000: (wireless) And here are the speeds with my old wrt54g: (Wireless) Here are the results directly hooked up to the modem: (wired)
 
I've tried setting the MTU to 1500, did a RMA with Linksys to see if it was a hardware problem, did a firmware update to the e1000, disabled DHCP and SPI, reseted my router and my modem....none of those things have worked
 
My ISP is comcast and I have a Arris TM502G modem

View 4 Replies View Related

Linksys Cable / DSL :: BEFCMU10 Need To Install And Get Cable Modem Working

Mar 24, 2011

I inherited a BEFCMU10 v.3 cable modem from my boss who switched to FiOS and I would like to use this with my Comcast connection.All I received from him is the cable modem and power adapter, what do I need to install and get this cable modem working? My router is WRT-54G.

View 2 Replies View Related

Linksys Cable / DSL :: Working With WAG320N Only As Modem ADSL?

May 7, 2012

i have Linksys WAG320N and Draytek Vigor 2850. My main router is Vigor, wchich support 2 WANs. First WAN is my VDSL connection (plug direct into Vigor) and second WAN i want ADSL connection. Can I work with WAG320N only as ADSL modem?

View 1 Replies View Related

Linksys Wireless Router :: How To Configure WRT54G With DSL Modem

Jul 22, 2008

I have WRTG54G with 4ports and a internet port, i have a zoom adsl modemfor DSL i wants to share DSL connection with internet port on WRTG54G but i d'nt know how to do this

View 5 Replies View Related

Linksys Wireless Router :: WRT54G FIOS And Actiontec Modem

Dec 29, 2006

Just had Verizon FIOS  service installed.  It comes with an actiontec modem.  I would like to remove the actiontec modem and connect directly to my Linksys RT31P2 which is cascaded to my Linksys WRT54G.  I have tried just about every router setup config; all with no success.  How to be able to connect the FIOS directly to a linksys router.

View 3 Replies View Related

Linksys Wireless Router :: Internet Access From DSL Modem But Not From WRT54G

Dec 25, 2011

I am trying to get wireless internet set up again and have run into a big issue.  Previous wireless router was also a WRT54G and she had problems.  I gave her my old one that I was no longer using, but it was still working with no problems.
 
The problem that I am having is that we are unable to get internet through the wireless router.  We are able to get the desktop connected to the internet when we plug it directly into the DSL modem, but when we plug the wireless modem into the DSL modem and the desktop into the wireless modem, then we don't get any internet connection at all.
 
I had her do a factory reset on modem so that we were starting fresh.  I have also tried unplugging both modems and then pluggin in the DSL and then Wireless modem, with no change.  We have the ability to get into wireless settings page, but I'm not sure what in there to change that would make any difference on this one.
 
I know that this problem isn't actually a wireless problem, but it has to be related to the modem.  We haven't even been able to get to the wireless part of the set up and we are already running into problems.

View 7 Replies View Related

Linksys Wireless Router :: WRT54G Antenna Extending Cable?

Feb 22, 2012

We have the Cisco WRT54G wifi router in many offices in this building. This router has two antennas. These antenna are screw into the back of the router unit. The antenna is male and router side is female of the connector. what are these connectors (some type of RF connectors)? How can we get extension cables for these to move the antenna from one fix location to another point?

View 4 Replies View Related

Wireless Arris Modem Won't Connect Via Ethernet

Nov 22, 2012

I got a new modem from the cable company Arris TG862G. This is a wireless modem and I had them set everything up on their end which is now after 2 hours with them on the phone working fine. The problem I'm having is somewhere in my computer is my guess and their guys didn't know which way was up so i gave up on them fixing my issue. So here I am. I have a custom built computer that is using a Gigabyte mobo and has been working fine with the on board Ethernet card before now. I used to have the desktop plugged into an Arris modem via a Belkin router and this set up worked fine. I also took the current modem and plugged it into the Belkin N600 router and then to my computer and to my complete bewilderment it worked fine. I wanted to get rid of the router so I could see if I could get faster download speeds (That initial issue being on speed tests I get 50mb/s and on actual downloads I would only get 5mb/s).

I got it to work (I have no idea how) for about 20 minuets. When I restarted the computer it stopped working. I am now back to square one which is the desktop not even recognizing that there is a cord plugged in. I know the cord is fine and the ports are fine as well that isn't the issue. My laptop connected just fine to the Ethernet cord with no issue. I have uninstalled the Belkin software to see if that was the issue and no change. Everything wireless works just fine, it is just this Ethernet connection that is FUBARed, and again ONLY with the desktop.I am running Windows 7 ultimate. I am about to QQ and just deal with the 5mb/s downlods because that's not terrible but I got greedy.I was messing with the Ethernet wire some and it started picking up the router but never tried to connect to the internet, I'm going to try other wires but I don't think that's the issue.

OK so another update ladies and gents: my desktop has been on for about 40 minuets now and it is connected to the modem. I have done nothing to it that would cause this and it just randomly happened. Short of never turning my computer off again which would be hell on my power bill what can I do to fix this problem? On speedtest.net I'm only getting 30.48 Mb/s and as I said earlier I should be getting around 50mb/s (which is what I get on on the wireless laptop). I just restarted it and it wouldn't connect to the modem again.

View 6 Replies View Related

Linksys Wireless Router :: WRT54g On Mac PowerPC G5 Not Working?

Sep 22, 2011

Running Comcast Business Class in my restaurant. I have a Mac Pro PowerPC G5 tower running OSX: 10.5.8. The Comcast guy hooked everything up along with the WRT54g i found in the basement (previous owner). Everything worked well, he programed the router through his internet pad; never touched my Mac.  All of a sudden my power outlet in which my modem and router are connected reset themselves. I reset them back on, however, my router Never worked again. My mac is directly connected to my modem, not router. I have it hooked up on LAN #4 (light turns on), however, after the outlet reset, the router wont even show up on my Modem's LAN. I cant open it open it on my browser, 192.168.0.1, or 1.1. I try the 30-30-30 reset, nothing. While looking for my own remedy, i think i downloaded the new firmware to my mac, nothing happened.

View 1 Replies View Related

Linksys Wireless Router :: WRT54G Is Not Working On Laptop

Apr 1, 2012

Linksys WRT54G wireless router is not working on my laptop. It is telling me this statement: ”The settings saved on this computer for the network do not match the requirements of the network.”

View 1 Replies View Related

Linksys Wireless Router :: WRT54g Seems To Have Quit Working?

Feb 7, 2012

I have tried everything I know.  My router is about 4 years old, so it may be time for a new one, but it has been working great, then it just stopped.

View 2 Replies View Related

Linksys Wireless Router :: WRT54g V3 Wi-Fi Stopped Working?

Feb 2, 2012

Last night, my wireless router suddenly stopped working. I no longer saw my router listed in my available wireless networks, and neither could my girlfriend from her computer. I unplugged the router to see if one of the available networks had disappeared in case my router had somehow been reset, and nothing changed so my computer isnt even seeing my router. Right now, I am wired through the router so I know the router works, but the wireless part doesnt for some reason. I was looking up stuff in the FAQ, and think the firmware is corrupted since the LEDs are all blinking. I was trying to update my firmware following the instructions I found using tftp.exe, however it failed. One problem is that I can't set up a static IP address since I need to access the web-based utility to check my DNS server but I cannot access the web-based utility anymore (maybe cause of the corrupted firmware?). On a related note, there is someone else in my building using a linksys with the default network name of linksys. I had changed my network's name and security-protected it, though that is all likely gone now since I tried to reset the router. My question is what will the network name of my router be if I saw it since "linksys" is already taken. or will there just be two of them?

View 1 Replies View Related

Linksys Wireless Router :: WRT54G Just Stopped Working?

Oct 19, 2007

I have WRT54G connected to a cable modem for internet service. Came home at lunch yesterday and all was working fine. Came home after work last night and couldn't connect to the internet. Called Charter cable this morning and their troubleshooting showed I can connect to the internet fine if I bypass the router, so the issue must be with the router (and of course not their problem...). How do I trouble shoot this? I've tried powering down the router and releasing and renewing IP addresses but it hasn't worked.

View 9 Replies View Related

Linksys Wireless Router :: WRT54G - Password Not Working?

Apr 24, 2011

I have  a Lynksys WRT54G wireless router.  It works just fine until I try to put a password on it.  I go through the basic steps, it talkes all my information and tells me everything is good.  I try to sign on the internet and it tells me my password is invalid....and YES Im sure its the right password I entered.  I went to http://192.168.1.1/wireless.htm and did all the necessary instructions, and still, it doesn't work. I can change my network name and it works.  As long as I leave it unprotected, everything works fine, but when I add the password, it tells me its invalid.  I even used 123456 so as to make sure it was the right one.

View 5 Replies View Related

Change Arris-TM502G Modem When Installing A Dual-Band Router?

Jun 14, 2011

Do I need to change myArris-TM502G router when changing to a Linksys E4200 Dual-Band modem

View 2 Replies View Related

D-link Dir-655 :: Arris Docsys3 Modem From Comcast Which Has A Built In Wifi Router

Aug 17, 2012

I have an ARRIS Docsys3 modem from Comcast which has a built in WiFi router. I also have a DIR-655. The Modem is in my office and I have a 100' Ethernet cable running through my attic to my front room where the dir-655 is located.

I use the DIR for WiFi as well I have it connected to my TV and Xbox.I use the ARRIS Modem for WiFi as well I have it connected to another Xbox and a Desktop computer.I want to have everything on 1 network, Dir-655 uses IP address 192.168.0.1-100 and the ARRIS uses ranges 10.0.0.1-100. I want to be able to connect to the dir-655 and have the IP for that connection join up with the 10.0.0... network so that I will be able to transfer files freely throughout the network.

I want everything on one network. Right now when I connect a laptop to the DIR-655, I can not access the printer that is connected to the Desktop on the ARRIS modem. I have to connect to the ARRIS modems WiFi to then use the printer on the desktop.Likewise, I want to use the media extender on the Xbox connected to the DIR-655 with the Desktop connected the the ARRIS modem, but I can not because of the to different networks.

View 5 Replies View Related

Linksys Wireless Router :: WRT54G - Ports Aren't Working?

Mar 24, 2013

I am running a Linksys Wireless G 2.4 GHz Broadband Router Model WRT54G.  I am unable to open any ports.  I upgraded to the latest firmware yesterday but still am unable to open any ports.  I even turned off my Symantec Internet Security Suite Firewall but still am unable to open any ports.

View 1 Replies View Related

Linksys Wireless Router :: WRT54G Not Working - Lights Blinking

Jul 17, 2011

I went online with a tech real quick before I found I beyond complimentary tech support. They say my router is working like a switch. I cannot get any wireless access and to the three direct connections to the router only one is working. The lights are constantly blinking, with the power light blinking every so often

View 1 Replies View Related

Linksys Wireless Router :: WRT54G Suddenly Stopped Working?

Jul 25, 2011

I have the Linksys WRT54G And it was working fine for years! Then today my computer shut down and when I turned it back on there was a connection but my computer was not responding to any commands. The icon shows full connectivity excellent connection. When I try to go to a web page it shows Connection Error and cannot get to any web pages.I am able to get on other wireless connections from neighbors but not mine. I have gone thru different directions on here and I am not technical and don't understand what is being said. I try to go to 192.168.1.1 and it asks for a password which I don't have. I have tried everything such as password and admin and get nothing.I am able to get my ip address and default gateway address and don't know the next step.

View 1 Replies View Related

Linksys Wireless Router :: WRT54G - Not Working After Firmware Update?

Nov 1, 2011

I have wirless router WRT54G ver.2. and I had firmware 2.0 So I downloaded new firmware From Here and did exactly as in instruction.
 
After update went successful I unplaged my router for 30 seconds but it's not working. I mean it's flashes and everything but can't access it and it is not broadcasting. and whats most interesting, reset buttom is not working
 
Want can I do? can I access it with some other way and reinstall firmware?

View 8 Replies View Related

Linksys Wireless Router :: WRT54G - Getting Connection And Proper Working?

Sep 8, 2012

I have 2 laptops in my home, I had no problem getting one to connect to the internet. The second one I'm having trouble connecting, I am wireless, I didn't have a problem at my old house with another laptop connecting to the internet with this router. I'm trying to save myself some money by not going through my wireless company, and end up having to get their router, which I already have their modem.

View 1 Replies View Related

Linksys Wireless Router :: WRT54G Wired Connection Stopped Working?

Jun 24, 2012

I have the WRT54G router for years and use it to provide both a wireless network for our home computers and a wired network for by internet phone that connects me to my office phone system and for my work computer and printer. Last week, the wired network stopped working. I checked the wiring and plugged my wire into all four of the ports in the back of the router with no success.  I followed the troubleshooting procedure that I found and changed the MTU setting.  I tried to update the firmware but the screen seemed to lock up and I was unable to complete the task.

View 9 Replies View Related

Linksys Wireless Router :: Internet Connection No Longer Working With WRT54G?

Sep 28, 2011

I have had a WRT54G V3 router working successfully for a number of years now with a couple wireless PCs through a cable modem with Comcast as my ISP.  All of a sudden yesterday, neither PC could access the internet.  No changes had been made to the router.
 
I contacted Comcast and they of course had me hard-wire one of my PCs into the cable modem.  That worked and I was able to access the internet.  However, when I tried to put the router back in place (in either a wired or wireless fashion), I could not access the internet.
 
I've tried following the online Linksys troubleshooting document ion.  The lights that should be lit on the router are lit.  I can access the router setup web page which shows the settings still intact.  I've tried going through the power sequencing to no avail.  Comcast says my router is the culprit of my problem, but I don't know why it would all of a sudden stop working.  My wireless printer still works so it detects a signal and my PC shows it's connected, but no internet access is possible.
 
What do I need to do?  Are there any other diagnostic tools available?  I'm out-of-warranty. 

View 4 Replies View Related

Linksys Cable / DSL :: Can't Get A New IP From ISP When Cable Modem EPC3925 Is Set To Router Mode

Mar 23, 2012

I can't get a new IP from my ISP when my Cable modem router(EPC3925) is set to router mode, i have tried factory restore, unplugged etc..but still no luck. It changes each time i reset it when i set it to bridged only mode but then i won't be able to connect other devices to it since it doesn't uses DHCP in bridged only mode. It changes back to the IP i had when i set it to router mode. I don't want to change my router settings to bridged only because it would disconnect the other devices in my house. Why my ISP assigns the same IP address when it's set to router mode but assigns different IPs when it's set to bridged only, how is this possible ?

View 1 Replies View Related

Linksys Wireless Router :: WRT54G - Websites / Wireless Device Stop Working?

Aug 12, 2008

wrt54g v1.1 After setting up the wireless router, I can use the internet on the pc as well as a wireless device. However after putting my pc in standby mode then back on, I can no longer connect to either. I have to restore factory defaults each time and re-enter all passwords and settings.

View 9 Replies View Related

Linksys Wireless Router :: WRT54g V3 Wireless Stopped Working?

Mar 3, 2008

Last night, my wireless router suddenly stopped working. I no longer saw my router listed in my available wireless networks, and neither could my girlfriend from her computer. I unplugged the router to see if one of the available networks had disappeared in case my router had somehow been reset, and nothing changed so my computer isnt even seeing my router. Right now, I am wired through the router so I know the router works, but the wireless part doesnt for some reason. I was looking up stuff in the FAQ, and think the firmware is corrupted since the LEDs are all blinking. I was trying to update my firmware following the instructions I found using tftp.exe, however it failed. One problem is that I can't set up a static IP address since I need to access the web-based utility to check my DNS server but I cannot access the web-based utility anymore (maybe cause of the corrupted firmware?). On a related note, there is someone else in my building using a linksys with the default network name of linksys. I had changed my network's name and security-protected it, though that is all likely gone now since I tried to reset the router. My question is what will the network name of my router be if I saw it since "linksys" is already taken. or will there just be two of them?

View 3 Replies View Related

Linksys Wireless Router :: E2500 Paired With ARRIS TM402P-110

Nov 26, 2012

i have rented a Flordia condo that has a ARRIS Modem model TM402P-110 that is available for my use to connect my laptop via an Ethernet hard wired connection. I understand that this is also a telephony modem that provides the phone service to the condo. The service provider for both the internet and phone servcice is Brightouse.
 
Will I have any issues connecting my Linksys E2500 router to this modem should I want to use my laptop wirelessly as well as my other wireless devices.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved