Linksys Cable / DSL :: BEFCMU10 Need To Install And Get Cable Modem Working

Mar 24, 2011

I inherited a BEFCMU10 v.3 cable modem from my boss who switched to FiOS and I would like to use this with my Comcast connection.All I received from him is the cable modem and power adapter, what do I need to install and get this cable modem working? My router is WRT-54G.

View 2 Replies


ADVERTISEMENT

Linksys Cable / DSL :: Befcmu10 V4 - Can't Login To Modem

Jul 7, 2008

I have Linksys Befcmu10 v4. I need to port forward and I cannot login. I have tried admin/password and all those combinations. I tried factory restore by pressing the thing in the back and still can't access the page

View 6 Replies View Related

Linksys Cable / DSL :: BEFCMU10 Goes Offline Then Back On

Nov 19, 2007

I have a BEFCMU10 v1 that has been misbehaving recently. It will go off line losing contact with the router and the Internet. It will stay off line for 8 to 10 minutes and then comeback on its own. If I cycle the power it will come up pretty quickly. Here is a log of a recent episode without power interruption.; [URL] Is there a solution or is it time for a new modem?

View 9 Replies View Related

Linksys Cable / DSL :: BEFCMU10 - Cannot Get Faster Internet Speed

Jan 15, 2007

I have a BEFCMU10 version 2.0 cable modem. My provider Insight Broadband has recently boosted their internet speeds. But I have found out that if my modem is not DOCSIS 2.0 compliant, I cannot get the faster speeds. How do I know if it is DOCSIS 1.1 or DOCSIS 2.0 compliant? I hope I don't have to replace the modem as it has given me absolutely no trouble since I have had it.

View 9 Replies View Related

Linksys Cable / DSL :: Working With WAG320N Only As Modem ADSL?

May 7, 2012

i have Linksys WAG320N and Draytek Vigor 2850. My main router is Vigor, wchich support 2 WANs. First WAN is my VDSL connection (plug direct into Vigor) and second WAN i want ADSL connection. Can I work with WAG320N only as ADSL modem?

View 1 Replies View Related

Linksys Wireless Router :: WRT54GS With Mac OS 10.6.8 And RCN Cable Modem Not Working?

Sep 27, 2011

I have a Linksys WRT54GS, version 6 with Mac OS X (version 10.6.8) hooked up to a Scientific Atlantic cable modem, with RCN as the ISP.
 
Recently, RCN had some network issues, and so I had to power down and reset my modem. The modem is working fine now -- no problems at all when the Mac is connected direclty to the modem.
 
The router's network is OK in that I can connect the Mac wirelessly to the network, but I can't connect to the internet through the router (through neither the wireless or wired connection).
 
I have downloaded the latest firmware update for the router, following the Linksys site instructions.
 
I did call Linksys tech support on the advice of RCN, and they said that the router does appear to be working (power, WLAN, and Internet lights are on), but they would be charging me nearly the cost of a new router to fix the problem.

View 1 Replies View Related

Linksys Cable / DSL :: Atlanta 2100 - When Installing Driver To Use Usb Cable Modem Does Not Recognize It

Dec 13, 2012

I have a modem Scientific Atlanta 2100. I just installed windows 8 pro 64bit and when installing the driver to use the usb cable modem does not recognize it and simply not installed. I wonder if it is possible to use my usb cable modem or simply incompatible with my windows 8 64bit pro.

View 3 Replies View Related

Linksys Cable / Dsl :: Cable Modem Dpc3825 - Hook Up To Smart Apps Wifi?

Apr 23, 2013

With this modem, can you hook up to the Linksys Smart Apps WiFi?

View 2 Replies View Related

Linksys Cable / DSL :: Can't Get A New IP From ISP When Cable Modem EPC3925 Is Set To Router Mode

Mar 23, 2012

I can't get a new IP from my ISP when my Cable modem router(EPC3925) is set to router mode, i have tried factory restore, unplugged etc..but still no luck. It changes each time i reset it when i set it to bridged only mode but then i won't be able to connect other devices to it since it doesn't uses DHCP in bridged only mode. It changes back to the IP i had when i set it to router mode. I don't want to change my router settings to bridged only because it would disconnect the other devices in my house. Why my ISP assigns the same IP address when it's set to router mode but assigns different IPs when it's set to bridged only, how is this possible ?

View 1 Replies View Related

Linksys Wireless Router :: Arris Cable Modem Not Working With WRT54G

Mar 7, 2007

I am at my wits end.Comcast just changed my old RCA cable modem for an Arris Telephony modem.(I had Comcast phone service added)The tech that did the install said the wireless G network was all up and running. (My 3 other computers and printer) Well lo and behold the network does not work at all. I only get internet through my wired computer and cannot access my router through 192.168.1.1 anymore.I tried powering down the router and modem by holding the reset for 30 seconds and unplugging them.

View 9 Replies View Related

Linksys Cable / DSL :: WAG320N And Cable Modem Connection?

Jun 4, 2010

some reference material about configuring my WAG320N to use my cable modem via Ethernet port 1. I've seen it mentioned that's its possible, however I've been unable to sort it out myself.
 
And before you ask, I've brought the DSL router as I'm moving in the next 12 months and my new base will not have access to cable internet and I'll be reverting back to DSL.

View 8 Replies View Related

RCA DCM315 Modem / 100MBps Charter Cable Install?

Jan 4, 2012

I have charter cable coming tomorrow to install cable television and internet. I am using my own modem and router instead of renting one because they dont have any available to meet the install date?Should I just rent one from them and wait or should I just buy a different cable modem. I will be getting the Ultra cable package from charter that has speeds up to 100Mbps download and 5Mbps upload. I would say it is going to run around 60. I have a RCA DCM315 modem and a Linksys WRT54G v6 router with DD-WRT firmware. max up and down speed for the RCA DCM315 modem.

View 1 Replies View Related

Routers / Switches :: Install Surfboard Extreme Wireless Cable Modem And Gigabit Router

Jan 13, 2013

My computer is not wireless so I have needed a wireless router from Time Warner. Directions tell me to connect to my computer. Will that solve the fact that my computer is not built in wireless?

View 2 Replies View Related

Linksys Cable / DSL :: WAG120N Won't Install

Mar 31, 2011

Just bought this WAG120N and using the CD Setup it gets as far as Install Gateway then displays its not connected properly. Checked everything it says to check.Im swapping from an ordinary adsl modem but i unplugged all of that and the WAG120N shows steady Power , 1 ethernet number lit and flashing ok,  Wireless is lit and DSL is also also lit.   Rebooted a few times too.

View 1 Replies View Related

Arris TM402P / 110 Cable Modem Randomly Stops Working

Aug 17, 2012

I am trying to figure out whats wrong with my parents apple airport router. Its connected into an Arris TM402P/110 cable modem. It randomly stops working, the network is there and shows up fine but you cant connect to it. It might work for a day or 2 and then just stops. I am trying to figure out if there is a configuration issue or the airport hardware is just failing. I am not sure where to start troubleshooting. The event log for the modem isnt much help, the following message shows up occasionally:

No Ranging Response received - T3 time-out

Whats interesting is my mom plugged her desktop right into the cable modem and then after plugging it back into the airport the wireless was working again. Is it possible there is a DHCP issue? If the hardware is failing what would be a good replacement for the airport?

View 2 Replies View Related

Linksys Cable / Dsl :: How To Install Wifi Antenna On Wag54g2

May 23, 2011

Let's say, an antenna like that Should I open the modem and therein there could be a slot for it to be plugged in? Because on the back side of the modem none of the slots will suit such plug.

View 2 Replies View Related

Linksys Cable / DSL :: WAG200G / WAP54G Or WGA54G - Unable To Install Device?

Mar 7, 2011

I have a LAN device (an SBS radar decoder). It is configurable with its own IP etc etc.I am not able to install this device where my router (a Speedport W 920V) currently is.So, can I use any of the above devices, perhaps as a bridge on my current wlan network, to allow me to plug in this LAN device so I can access it anywhere in my house on the wlan?

View 1 Replies View Related

Linksys Cable / DSL :: WAG320n Use As Modem Only?

Jul 17, 2011

I have a WAG320n and I wish to use it as a modem only so that I can use an Airport Extreme as my wireless router. how to configure the WAG320n so that it can be used in this configuration?

View 1 Replies View Related

Linksys Cable / DSL :: E1550 Cannot Connect Via Dsl Modem

Oct 2, 2011

Have an existing befsr41 / westell b90-210015 connection that has been working for years... replaced the befsr41 with a e1550 and cannot connect to the internet. Tried to connect to the modem directly to see how to put into 'bridge mode' but cannot find the right ip address.

View 1 Replies View Related

Linksys Cable / DSL :: How To Configure WAG120N As A Modem

Apr 18, 2013

I have WAG120N and is working fine, but has very poor wifi range. I recently purchased EA 6500. how to setup my WAG120N as a modem only and shift all routing to the EA6500

View 2 Replies View Related

Linksys Cable / DSL :: Hookup ATT DSL Modem With E1200?

Apr 22, 2013

I presently have ATT DSL Motorola modem (Model 2210-02-1022) with (1) DSL Green plug, and (2) Ethernet-Yellow in the back of my modem.I have reset the E1200 Router, and tried multiple ways of getting the Wi-Fi to work.  This Linksys E1200 belonged to my neighbor, but he recently passed away, and left me all his computer devices.In the Wall phone jack, I have a DSL noise filter as part as a two female plug,

1) for the Green DSL on Modem, and the other

2) to my phone handset. The way I usually plug this in BEFORE this router was this: The green DSL plug from Modem - into phone jack DSL Filter, and the Yellow ETHERNET cord from Router to the back of Computer. I powered on computer, plugged in all cords, except for E1200 power cord, disabled antivirus/security software,  I then inserted the Cisco Connect CD and waited , and waited, but it said I was not connected to the Internet.  ERROR CODE# 82BD0304. I'm using win7 64 Pro.  before i called ATT, I wanted to know if there is an easier way to conect the right cords to the right plugs.

View 1 Replies View Related

Linksys Cable / DSL :: Can't Seem To Setup WAG120N Modem

Nov 27, 2011

I can't seem to setup my WAG120N modem.I kept on getting the error "your ethernet cable does not appear to be connected properly" even though I have connected all the cables correctly. I can access the modem through the browser via 192.168.1.1 though.I thought the setup is supposed to be simple but I have wasted few hours.

View 1 Replies View Related

Linksys Cable / DSL :: X3000 Log Is Not Working?

Oct 1, 2012

Log enabled using [URL] , config saved, modem power cycled...... no in and out log after internet use. 

View 1 Replies View Related

Linksys Cable / DSL :: WCG200G Wireless Resets The Modem?

Apr 27, 2012

WCG200G ver.2  resets everytime i use wireless
 
Firmware Version: 2.0.3.6.12-0608

View 8 Replies View Related

Linksys Cable / DSL :: How To Configure WAG120N Modem / Router

Jun 25, 2012

I just ordered the Linksys WAG120N modem/ router and need configuring the same on the BSNL network. Any Document or link about his Installation and configuration.

View 3 Replies View Related

Linksys Cable / DSL :: X1000 Modem Router Crashes?

Apr 15, 2013

I have just bought an X1000 box, it seems to be randomly locking up and the only way around the issue is to reboot.  I have also noticed it can't seem to handle streaming video either.
 
My ADSL has been checked and all is OK and if I don't stream video generally things seem OK for a couple of days.  If I run a continual ping to the unit you can see that now and again the request times out but then some times comes back and other times I need to reboot again.  The log file seems to show very little either.

View 1 Replies View Related

Linksys Cable / DSL :: X3000 Used As A Router Behind A VDSL Modem

Nov 10, 2012

I desperately try to set up the X3000 as a router behind a vDSL modem. When I choose connection through Ethernet and then PPPoE, it never keep the credentials after reboot in spite of having saved the data before.

View 6 Replies View Related

Linksys Cable / DSL :: Updating X3000 Modem Router

Jul 8, 2012

I recently purchased two x3000 devices.Both shipped with the 1.0.01 firmware installed.Upgraded one device in one location to the 1.0.03.001 release without issue.A day later i'm not trying from a second location to perform the same action.I've downloaded the FW_X3000_1.0.03.001.bin firmware from the Cisco downloads for the device and receive a pop up 'The image file is incorrect'.I've downloaded hte image twice and it appears to be correct in size. I'm following the same process that worked without issue the day previously.

View 3 Replies View Related

Linksys Cable / DSL :: WAG200G - Slow Down A Modem Router?

Mar 23, 2011

Is there a way through settings (I have a Linksys WAG200G modem/router) to slow the internet speed (much like shaping)?

View 2 Replies View Related

Linksys Cable / Dsl :: X1000 Modem Does Not Allow Connection To Wifi?

Mar 13, 2013

I recently bought an x1000 modem/router and found that after 2/3 days of staing active and properly functioning, it does not allow me to login to wifi connection with none of my devices (tried iPhone, iPad and 2 windows pc).Firmware version is v1.0.00 build 018 Sep 04, 2012

View 4 Replies View Related

Linksys Cable / DSL :: See DSL Path Mode On WAG54G2 Modem

Nov 7, 2011

How can I see "DSL Path Mode" on my WAG54G2 modem, How do i know,the line FAST PATH or INTERLEAVE ?

View 1 Replies View Related

Linksys Cable / DSL :: WAG35G To Act As Modem Passing Through A Static IP?

Feb 27, 2011

I currently have a WAG354G configured with a static IP address acting as a DHCP server. Wireless is off, and instead I have an Apple Airport Extreme basestation in bridge mode to which my client machines connect wirelessly.
 
Instead I want to pass through the static IP address to the Apple basestation, and use this as my DHCP server.
 
Ultimately I want the Apple basestation to pass the static IP address through to my home server, and also supply DHCP addresses to other clients.

View 5 Replies View Related

Linksys Cable / DSL :: Cisco Modem DPC3825 Won't Recognize It

Mar 27, 2012

I recently upgraded, through my ISP, my high-speed modem to the DPC3825 model modem/router. But when I try to connect to the DLink switch, the modem freezes, and doesn't recognize it.  My previous setup was modem, to my DLink router (DIR 615), to my switch. With my new setup, I just bypassed the DLink router, because my new modem includes router capability.Is there some compatibility issue between the new modem and the DLink switch?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved