Linksys Cable / DSL :: Hookup ATT DSL Modem With E1200?
Apr 22, 2013
I presently have ATT DSL Motorola modem (Model 2210-02-1022) with (1) DSL Green plug, and (2) Ethernet-Yellow in the back of my modem.I have reset the E1200 Router, and tried multiple ways of getting the Wi-Fi to work. This Linksys E1200 belonged to my neighbor, but he recently passed away, and left me all his computer devices.In the Wall phone jack, I have a DSL noise filter as part as a two female plug,
1) for the Green DSL on Modem, and the other
2) to my phone handset. The way I usually plug this in BEFORE this router was this: The green DSL plug from Modem - into phone jack DSL Filter, and the Yellow ETHERNET cord from Router to the back of Computer. I powered on computer, plugged in all cords, except for E1200 power cord, disabled antivirus/security software, I then inserted the Cisco Connect CD and waited , and waited, but it said I was not connected to the Internet. ERROR CODE# 82BD0304. I'm using win7 64 Pro. before i called ATT, I wanted to know if there is an easier way to conect the right cords to the right plugs.
View 1 Replies
ADVERTISEMENT
Apr 9, 2013
Reset to factory defaults. DHCP turned on. Status page shows black for router IP, gateway, and DNS addresses. Powered router+cable modem on/off multiple times already. I also have another wifi router (WRT120N) and it works fine.
Pretty simple connection. Just a ethernet cable between the cable modem and E1200 internet port (Cable modem <---> E1200)
View 2 Replies
View Related
Nov 8, 2011
Have high speed cable and find that the wireless speeds using Speedtest.net are faster than when hooking directly into the E4200. Do I have something set incorrectly?
View 3 Replies
View Related
Apr 10, 2011
I have been trying for days to get a HP Photosmart Plus B209a wireless printer to work with my D-Link DIR-655.Going through the HP setup cd for I get to the section where it wants to hookup a usb cable to get router settings and finds my network and then I put in the password. Then after looking for a bit it says it can't find the printer.Looking at the wireless status page it says the ip address is 0.0.0.0.Reading on HP's website it says that you must have the router set to broadcast the SSID, I believe mine is set to hide. How would I go about changing it to broadcast AND would it mess up all my other settings changing it to Broadcast, meaning will I have to reconfigure the other computers again? Do I use the set up wizard to edit things or is that for first time set up ?
View 5 Replies
View Related
Apr 29, 2013
I have a Linksys E1200 modem and I am only getting less than 1.0 mbps download speeds. When connected via ethernet cable to the router, my download speed is > 50 mbps.
View 2 Replies
View Related
Oct 24, 2011
Internet went out for 3 days straight and calling frontier about 20 times they finally gave us a new model 7500 modem to replace the previous. The linksys e1200 router which had worked perfectly fine before the new modem has decided to not allow me to connect online. Sometimes it says im connected to internet but web browser does not connect, sometimes it says no internet access. I have no idea what i am doing so im not sure if it is a modem or router issue. I have done full reboots of both and powered on correctly. plugging in the modem into ports 1-3 do not light up the modems ports lights, only port 4 seems to light up when plugged in however computers light up all the ports when hard wired to E1 - E4.i also downloaded the latest firmware update for the linksys e1200 router.All fire walls are shut off and no WEP ( we live in middle of nowhere so a key is not needed )
View 7 Replies
View Related
Nov 28, 2011
I set up an E1200 about two weeks ago to replace our old DI-524 because our net speeds were getting throttled (the old router wouldn't support anything higher than 10mbps). The same day, we started getting modem resets (We have an SB6120). This never happened on the old router but it's constantly happening with this new one. It'll happen multiple times a day. I called Cox Tech Support and they pushed an upgrade onto the modem but it still reset. I don't think it's the router, since I don't understand why it would force the modem to reset, but this never happened before I installed it. The firmware is updated to the latest version on the Cisco site (1.0.02).
View 5 Replies
View Related
Mar 6, 2012
My parents are using a speedtouch 546 modem for their wired internet connection, but they would like wireles in their home. I therefore bought them a linksys e1200, and tried to get their wireless internet working.
I connected the e1200 to the speedtouch via kabel, used the cisco software to install the wifi network, and so far so good. The laptop has no problem connecting to the e1200, but no internet connection, whatever I do.
There seems to be a signal comming into the back of the e1200, since the led on both the speedtouch and the e1200 are responding, indicating that the two are sharing some information.
Looking for information on the net, I came onto 3 possible solutions.
One is cloning the MAC adress of the to the speedtouch connected wired computer to the e1200. The second has something to do with interfering IP adress ranges. The third was uninstalling the cisco software, reconnecting and resetting the modem. Let windows find the hardware and just install the e1200 drivers.
View 2 Replies
View Related
Dec 2, 2012
I purchased the E1200 Linksys Wireless Router on 11/26/12. The router worked fine until today. Without reason, the router stopped reading the internet cable/the port on the router stopped detecting the signal from the cable connected to the modem. I can plug the cable from the modem directly into a laptop and the laptop picks up the signal (using it to write this). I swapped out several DSL cables to confirm it wasn't a cable issue and it does not make a difference. I tried rebooting the router, resetting the router, and yet nothing works.
View 4 Replies
View Related
Jun 24, 2012
I have a new Linksys E2100 that was working well with an old Verizon modem. Then recently that modem gave up the ghost and I was issued another one (Westel Model 6100G). I have no problems with internet connectivity when connecting directly from my harddrive to the Verizon modem. I am also not having trouble connecting to the Linksys routher as I am able to see my wireless connection with no problem. However, when I try to set up the connnection with the E2100 in the loop (yes, it's connected correctly) I no longer have internet access.I tried de-installing and re-installing the Linksys software (thinking maybe there was some new configuration that would be auto-detected with a new set-up), but this didn't work. I suspect that if the problem is with my Linksys router and not with my Verizon modem that there might be something that could be done to reconfigure something manually but I do not know enough about connections and wireless systems to trust myself not to mess something up.
View 1 Replies
View Related
Jun 24, 2012
I have a new Linksys E2100 that was working well with an old Verizon modem. Then recently that modem gave up the ghost and I was issued another one (Westel Model 6100G). I have no problems with internet connectivity when connecting directly from my harddrive to the Verizon modem. I am also not having trouble connecting to the Linksys routher as I am able to see my wireless connection with no problem. However, when I try to set up the connnection with the E2100 in the loop (yes, it's connected correctly) I no longer have internet access.
I tried de-installing and re-installing the Linksys software (thinking maybe there was some new configuration that would be auto-detected with a new set-up), but this didn't work. I suspect that if the problem is with my Linksys router and not with my Verizon modem that there might be something that could be done to reconfigure something manually but I do not know enough about connections and wireless systems to trust myself not to mess something up.
At this point I'm assuming it's a Linksys issue since I know that my Verizon modem can connect me to the internet, so works properly. Is there some known incompatibility with this Linksys model and the Westell 6100G modem?
View 2 Replies
View Related
Jan 7, 2012
My son tried to "speed up" our connection by unplugging modem&router. now can't get both talking to each other. Tried numerous steps! Bought Router 8/11/11, so NO Support from Cisco(only 90 days-POOR!). Website useless. Modem works fine with PC wired in.
View 3 Replies
View Related
Dec 13, 2012
I have a modem Scientific Atlanta 2100. I just installed windows 8 pro 64bit and when installing the driver to use the usb cable modem does not recognize it and simply not installed. I wonder if it is possible to use my usb cable modem or simply incompatible with my windows 8 64bit pro.
View 3 Replies
View Related
Apr 23, 2013
With this modem, can you hook up to the Linksys Smart Apps WiFi?
View 2 Replies
View Related
Aug 14, 2012
The wireless router, which is a linksys E1200 is completely new. I setup the entire wireless and there was no problems on that front.The problem is the wireless connection. Even when I am within a few inches of the router, I couldn't even load a youtube video properly. It buffers every 2 seconds. But when I plug the cable into my computer, it works completely fine. The signal strength is excellent all the time.
I tried using inSSIDer to look for the number of connections within my area for the one with the least inteference and found that I'm already on the good one, or actually, all of them looked more or less the same. But I tried changing anyways from 1 to 6 to 11, and none of them made a difference.I then tried changing my Wireless Security to WPA2 Personal. Then I tried changing the Wireless Network Mode to Wireless-G Only instead of Mixed and the wireless speed increased.
View 5 Replies
View Related
Mar 24, 2011
I inherited a BEFCMU10 v.3 cable modem from my boss who switched to FiOS and I would like to use this with my Comcast connection.All I received from him is the cable modem and power adapter, what do I need to install and get this cable modem working? My router is WRT-54G.
View 2 Replies
View Related
Mar 23, 2012
I can't get a new IP from my ISP when my Cable modem router(EPC3925) is set to router mode, i have tried factory restore, unplugged etc..but still no luck. It changes each time i reset it when i set it to bridged only mode but then i won't be able to connect other devices to it since it doesn't uses DHCP in bridged only mode. It changes back to the IP i had when i set it to router mode. I don't want to change my router settings to bridged only because it would disconnect the other devices in my house. Why my ISP assigns the same IP address when it's set to router mode but assigns different IPs when it's set to bridged only, how is this possible ?
View 1 Replies
View Related
Jun 4, 2010
some reference material about configuring my WAG320N to use my cable modem via Ethernet port 1. I've seen it mentioned that's its possible, however I've been unable to sort it out myself.
And before you ask, I've brought the DSL router as I'm moving in the next 12 months and my new base will not have access to cable internet and I'll be reverting back to DSL.
View 8 Replies
View Related
Jun 27, 2012
I have a wireless modem/router combo right now provided to me by Centrylink, its the Q1000. I am trying to hook up a 2nd router to our network to extend range and allow extra ethernet connections points. The new (2nd) Router is a Linksys E1200. I have been told by multiple sources it should be possible to hook the Linksy's router to the modem/router, but I am still not sure how to. All of the directions I have read involve disconnecting the old router (in my case, the Q1000) and then connecting the new router (E1200) in order to configure it. But I am not sure how to do this with out the internet access provided by the old router. how to cascade like this while using a modem/router
View 6 Replies
View Related
Jul 17, 2011
I have a WAG320n and I wish to use it as a modem only so that I can use an Airport Extreme as my wireless router. how to configure the WAG320n so that it can be used in this configuration?
View 1 Replies
View Related
Oct 2, 2011
Have an existing befsr41 / westell b90-210015 connection that has been working for years... replaced the befsr41 with a e1550 and cannot connect to the internet. Tried to connect to the modem directly to see how to put into 'bridge mode' but cannot find the right ip address.
View 1 Replies
View Related
Apr 18, 2013
I have WAG120N and is working fine, but has very poor wifi range. I recently purchased EA 6500. how to setup my WAG120N as a modem only and shift all routing to the EA6500
View 2 Replies
View Related
Jul 7, 2008
I have Linksys Befcmu10 v4. I need to port forward and I cannot login. I have tried admin/password and all those combinations. I tried factory restore by pressing the thing in the back and still can't access the page
View 6 Replies
View Related
Nov 27, 2011
I can't seem to setup my WAG120N modem.I kept on getting the error "your ethernet cable does not appear to be connected properly" even though I have connected all the cables correctly. I can access the modem through the browser via 192.168.1.1 though.I thought the setup is supposed to be simple but I have wasted few hours.
View 1 Replies
View Related
Apr 27, 2012
WCG200G ver.2 resets everytime i use wireless
Firmware Version: 2.0.3.6.12-0608
View 8 Replies
View Related
Jun 25, 2012
I just ordered the Linksys WAG120N modem/ router and need configuring the same on the BSNL network. Any Document or link about his Installation and configuration.
View 3 Replies
View Related
Apr 15, 2013
I have just bought an X1000 box, it seems to be randomly locking up and the only way around the issue is to reboot. I have also noticed it can't seem to handle streaming video either.
My ADSL has been checked and all is OK and if I don't stream video generally things seem OK for a couple of days. If I run a continual ping to the unit you can see that now and again the request times out but then some times comes back and other times I need to reboot again. The log file seems to show very little either.
View 1 Replies
View Related
Nov 10, 2012
I desperately try to set up the X3000 as a router behind a vDSL modem. When I choose connection through Ethernet and then PPPoE, it never keep the credentials after reboot in spite of having saved the data before.
View 6 Replies
View Related
Jul 8, 2012
I recently purchased two x3000 devices.Both shipped with the 1.0.01 firmware installed.Upgraded one device in one location to the 1.0.03.001 release without issue.A day later i'm not trying from a second location to perform the same action.I've downloaded the FW_X3000_1.0.03.001.bin firmware from the Cisco downloads for the device and receive a pop up 'The image file is incorrect'.I've downloaded hte image twice and it appears to be correct in size. I'm following the same process that worked without issue the day previously.
View 3 Replies
View Related
May 7, 2012
i have Linksys WAG320N and Draytek Vigor 2850. My main router is Vigor, wchich support 2 WANs. First WAN is my VDSL connection (plug direct into Vigor) and second WAN i want ADSL connection. Can I work with WAG320N only as ADSL modem?
View 1 Replies
View Related
Mar 23, 2011
Is there a way through settings (I have a Linksys WAG200G modem/router) to slow the internet speed (much like shaping)?
View 2 Replies
View Related
Mar 13, 2013
I recently bought an x1000 modem/router and found that after 2/3 days of staing active and properly functioning, it does not allow me to login to wifi connection with none of my devices (tried iPhone, iPad and 2 windows pc).Firmware version is v1.0.00 build 018 Sep 04, 2012
View 4 Replies
View Related
Nov 7, 2011
How can I see "DSL Path Mode" on my WAG54G2 modem, How do i know,the line FAST PATH or INTERLEAVE ?
View 1 Replies
View Related