Linksys Wireless Router :: E1200 Causing Modem To Reset?
Nov 28, 2011
I set up an E1200 about two weeks ago to replace our old DI-524 because our net speeds were getting throttled (the old router wouldn't support anything higher than 10mbps). The same day, we started getting modem resets (We have an SB6120). This never happened on the old router but it's constantly happening with this new one. It'll happen multiple times a day. I called Cox Tech Support and they pushed an upgrade onto the modem but it still reset. I don't think it's the router, since I don't understand why it would force the modem to reset, but this never happened before I installed it. The firmware is updated to the latest version on the Cisco site (1.0.02).
View 5 Replies
ADVERTISEMENT
Jul 6, 2011
My new HP Touchpad 32 GB is causing my E4200 to reset. I can duplicate the issue by simply access the HP App Catalogue. I upgraded the firmware from 1.01 to 1.03 build 13 and the issue still exists.
View 1 Replies
View Related
Mar 29, 2012
I have an E1550 less than 1 year old. Lately, I have been losing internet on the AT&T modem. I called AT&T but as part of their diagnostics, I have to plug the modem directly into the PC. I have loaded the latest firmware to the E1550.Lose Internet but wireless connectivity to router exists.Internet light on modem is out (modem is connected to router)Unplug modem and leave off plug in, internet light is still out.Unplug router, plug router back in - no internet connection but do have wireless connectivity to router.Take cable from modem to router and plug directly into PC internet light comes on in modem and I have internet from PC.Take cable from PC and plug back into router .I have internet via wireless.What I can't figure out is what could be happening in router that would impact modem internet connection. I have replicated this at least 3 times. Yes, the modem is a bit old, but since plugging it directly into the PC works, I'm thinking it has to be the router and I cannot figure out why unless there's some sort of electrical thing going on in the router.
View 4 Replies
View Related
Oct 20, 2012
I am trying to setup two wireless routers in my network. I purchased a E1200 N router and an older G Linksys router upstairs.When I got the N router I set it up a stand alone router and it worked great for a week or so. I then wanted to try to get both routers going to I changed the IP address on E1200 to 192.168.2.1....the router rebooted and then could not login. I am not able to get any internet conntion anymore. When I type 192.168.2.1 it goes to page can not be displayed, 192.168.1.1 same thing. Ipconfig shows some address auto address that I did not put in and i am also not connected to a modem. I cant log into the router at all.So reset: I held down the button for 30 seconds...let go and it blinks and then goes solid but does not reset. Unplugged router for 5 minutes tried again. Cant get into 192.168.1.1..will not prompt for anything. I have tried to reset this router about 10 times and can not get into the default login at all.
View 1 Replies
View Related
Jul 29, 2012
since last nite my router E1200 has been having speed up and down problems.first it goes to 150mb/s then back down to 1 for a few minutes, usualy its stuck at 72mb/s which is a far cry from its rated 300mbps but qi'd rahter have that than 1-2mbps.i'd be happy with 150mbps but that only lasts 5mins then goes down to 1-2mbps and i have to reset my connection.
View 9 Replies
View Related
Jan 19, 2013
I have an E1200 and if a device - such as my tablet or laptop - is left unused for a period of time - say for 4 or 5 hours - they won't reconnect to the router unless I do a power cycle/reset on the router.
View 5 Replies
View Related
Mar 6, 2012
My parents are using a speedtouch 546 modem for their wired internet connection, but they would like wireles in their home. I therefore bought them a linksys e1200, and tried to get their wireless internet working.
I connected the e1200 to the speedtouch via kabel, used the cisco software to install the wifi network, and so far so good. The laptop has no problem connecting to the e1200, but no internet connection, whatever I do.
There seems to be a signal comming into the back of the e1200, since the led on both the speedtouch and the e1200 are responding, indicating that the two are sharing some information.
Looking for information on the net, I came onto 3 possible solutions.
One is cloning the MAC adress of the to the speedtouch connected wired computer to the e1200. The second has something to do with interfering IP adress ranges. The third was uninstalling the cisco software, reconnecting and resetting the modem. Let windows find the hardware and just install the e1200 drivers.
View 2 Replies
View Related
Aug 31, 2011
If my computer has been sitting for a while without using the internet and i open my browser the dsl and internet lights on my router shut off for about 15 seconds and no one in my house has internet and then it turns back on. this ONLY happens when it has been sitting for a while with the browser closed and my computer is the only one that makes it do it. also i don't have my computer set to sleep after a certain time, my monitor turns off after 5 minutes and that's it. i have a siemens gigaset se567 and my isp is telus.
View 1 Replies
View Related
Jun 24, 2012
I have a new Linksys E2100 that was working well with an old Verizon modem. Then recently that modem gave up the ghost and I was issued another one (Westel Model 6100G). I have no problems with internet connectivity when connecting directly from my harddrive to the Verizon modem. I am also not having trouble connecting to the Linksys routher as I am able to see my wireless connection with no problem. However, when I try to set up the connnection with the E2100 in the loop (yes, it's connected correctly) I no longer have internet access.I tried de-installing and re-installing the Linksys software (thinking maybe there was some new configuration that would be auto-detected with a new set-up), but this didn't work. I suspect that if the problem is with my Linksys router and not with my Verizon modem that there might be something that could be done to reconfigure something manually but I do not know enough about connections and wireless systems to trust myself not to mess something up.
View 1 Replies
View Related
Apr 9, 2013
Reset to factory defaults. DHCP turned on. Status page shows black for router IP, gateway, and DNS addresses. Powered router+cable modem on/off multiple times already. I also have another wifi router (WRT120N) and it works fine.
Pretty simple connection. Just a ethernet cable between the cable modem and E1200 internet port (Cable modem <---> E1200)
View 2 Replies
View Related
Jun 24, 2012
I have a new Linksys E2100 that was working well with an old Verizon modem. Then recently that modem gave up the ghost and I was issued another one (Westel Model 6100G). I have no problems with internet connectivity when connecting directly from my harddrive to the Verizon modem. I am also not having trouble connecting to the Linksys routher as I am able to see my wireless connection with no problem. However, when I try to set up the connnection with the E2100 in the loop (yes, it's connected correctly) I no longer have internet access.
I tried de-installing and re-installing the Linksys software (thinking maybe there was some new configuration that would be auto-detected with a new set-up), but this didn't work. I suspect that if the problem is with my Linksys router and not with my Verizon modem that there might be something that could be done to reconfigure something manually but I do not know enough about connections and wireless systems to trust myself not to mess something up.
At this point I'm assuming it's a Linksys issue since I know that my Verizon modem can connect me to the internet, so works properly. Is there some known incompatibility with this Linksys model and the Westell 6100G modem?
View 2 Replies
View Related
Jan 7, 2012
My son tried to "speed up" our connection by unplugging modem&router. now can't get both talking to each other. Tried numerous steps! Bought Router 8/11/11, so NO Support from Cisco(only 90 days-POOR!). Website useless. Modem works fine with PC wired in.
View 3 Replies
View Related
Jun 27, 2012
I have a wireless modem/router combo right now provided to me by Centrylink, its the Q1000. I am trying to hook up a 2nd router to our network to extend range and allow extra ethernet connections points. The new (2nd) Router is a Linksys E1200. I have been told by multiple sources it should be possible to hook the Linksy's router to the modem/router, but I am still not sure how to. All of the directions I have read involve disconnecting the old router (in my case, the Q1000) and then connecting the new router (E1200) in order to configure it. But I am not sure how to do this with out the internet access provided by the old router. how to cascade like this while using a modem/router
View 6 Replies
View Related
Oct 24, 2011
Internet went out for 3 days straight and calling frontier about 20 times they finally gave us a new model 7500 modem to replace the previous. The linksys e1200 router which had worked perfectly fine before the new modem has decided to not allow me to connect online. Sometimes it says im connected to internet but web browser does not connect, sometimes it says no internet access. I have no idea what i am doing so im not sure if it is a modem or router issue. I have done full reboots of both and powered on correctly. plugging in the modem into ports 1-3 do not light up the modems ports lights, only port 4 seems to light up when plugged in however computers light up all the ports when hard wired to E1 - E4.i also downloaded the latest firmware update for the linksys e1200 router.All fire walls are shut off and no WEP ( we live in middle of nowhere so a key is not needed )
View 7 Replies
View Related
Nov 12, 2011
My wireless was working but would load some pages super slow and others just fine. I reset my modem and router and now I can wireless connect to the router but get no connection. If I plug my computer directly to the modem I can connect the internet just fine. But if I hook up my router and connect it to my pc through a cable it can't connect just like the wireless.I have a linksys WRT54GSv1 Comcast is my ISP I ran Xirrus connection test and it said DNS Lookup Failure then No IP Availible.This is an ipconfg /all result
Code:
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:Users**********>ipconfig /all
[code]....
View 3 Replies
View Related
Oct 28, 2011
Basically, my issue stems from the latest Boxee firmware from 2 weeks ago, that since then, its been causing my DIR 655 to reset itself, thereby disabling my whole home internet. It eventually turns back on again after a while, but the process doesn't stop.Basically, my DIR 655 is connected, hard wired to my boxee. I also have a NAS 323 hard wired to my router. I've had this setup on my boxee, reading all my movies/shows from my NAS without any issues for the past 10 months. Then the firmware from 2 weeks ago on the boxee started to cause my router to reset. I thought it was a hardware router failure, so I bought another of the same model to try that out, same thing happened though. When I rolled back my boxee firmware to the previous version, it no longer causes my router to reset.Now, besides me trying to figure out how to correctly block the boxee from updating on the router. Is there anything I can do on the router to tell it to prevent it from letting the boxee forcing it to reset? I'm on High Speed DSL. My internet provider modem is acting as a bridge to my DIR 655. Its been working fine for the past 10 months.
I've also done the following:Ensure DNS IP addresses are being filled in under Setup/Internet/Manual? You can find thse under Status/Device Info/Wan section. Turned off ALL QoS Turned off Advanced DNS Services if you have this option under Setup/Internet/Manual.Turned on DNS Relay under Setup/Networking.Setup DHCP reserved IP addresses for all devices on my router.Ensure devices are set to auto obtain an IP address.I have Set Firewall settings to Endpoint Independent for TCP and UDP..
Basically, I've put my boxee back to my previous firmware, and this doesn't cause my router to reset and disable my internet. But I don't get how/why a firmware update can trigger my router to do this?
View 6 Replies
View Related
Oct 4, 2012
The first part, is this even possible? Modem to switch.
Second part, e1200 router plugged into switch, handles DHCP for the switch.
Plug gigabit computers into the switch, non gigabit/wireless devices into the e1200 router.
If e1200 can't handle DHCP for the switch, could I configure a DHCP linux server directly to the switch?
I don't want to limit my network to my e1200 speeds when I have a gigabit capable modem and a gigabit capable switch.
View 1 Replies
View Related
Jul 25, 2011
Since recently replacing my home router with a Linksys E2500, I have been getting Blue Screen of Death (BSOD) with my Company's VPN (AT&T). It only happens when I am running wireless with my E2500. If I am hooked up to my E2500 through a ethernet cable it doesn't happen. I have updated the BIOS on my Lenovo Thinkpad T410 and ensured all of my drivers are up to date. I am 99.9% sure the problem is caused by my Linksys E2500 because I have used my laptop on other wireless routes at work and school and never get this problem. I am also ensured that my E2500 has the current firmware installed and upgraded my Company's VPN to the most current level to no avail.
I am getting DRIVER_IRQL_NOT_LESS_OR_EQUAL Blue Screen of Death in agnfilt.sys.
View 9 Replies
View Related
Jun 30, 2011
For some reason, I have been trying to use QOS for several network related jobs (VPN, streaming). It would seem that when QOS is enabled and the appropriate ports are set which a high priority, the speed of my connection drops to a crawl. When I disable QOS, I'm flying again. I have confirmed ports, and protocol types (TCP or UDP) and nothing seems to work.
View 2 Replies
View Related
Oct 18, 2011
I just bought a Samsung BD-D5300 Blu-ray player that allows a bunch of networking options including wireless and wired. I was using the wired option when I came across some conflicts with my network using a Linksys WRT350N v1. The Samsung conflicted with the Linksys's DHCP server. The blu-ray player turns off automatically when inactive. It was causing conflicts with my iPad 2, MacBook Pro and Motorola Atrix android phone whenever it got assigned an IP address. When I reset the router and my cable modem, it wasn't assigned an address for awhile, which fixed things, but as soon as it got an address again, it was caused conflicts by being seen as a LAN by my router. When it wasn't receiving an address, it got the automatic private IP address of 169.x.x.x. When I removed the connection with my router, the conflicts disappeared and my computers were able to access my wifi again.
View 1 Replies
View Related
Apr 22, 2013
I presently have ATT DSL Motorola modem (Model 2210-02-1022) with (1) DSL Green plug, and (2) Ethernet-Yellow in the back of my modem.I have reset the E1200 Router, and tried multiple ways of getting the Wi-Fi to work. This Linksys E1200 belonged to my neighbor, but he recently passed away, and left me all his computer devices.In the Wall phone jack, I have a DSL noise filter as part as a two female plug,
1) for the Green DSL on Modem, and the other
2) to my phone handset. The way I usually plug this in BEFORE this router was this: The green DSL plug from Modem - into phone jack DSL Filter, and the Yellow ETHERNET cord from Router to the back of Computer. I powered on computer, plugged in all cords, except for E1200 power cord, disabled antivirus/security software, I then inserted the Cisco Connect CD and waited , and waited, but it said I was not connected to the Internet. ERROR CODE# 82BD0304. I'm using win7 64 Pro. before i called ATT, I wanted to know if there is an easier way to conect the right cords to the right plugs.
View 1 Replies
View Related
Jun 19, 2012
I've had an E4200v1 in use as my home's main router for about 3 mos. And while many others have reported disconnect problems (I think), I myself have never seen any. My router and its N & G wifi networks have been rock solid. Until yesterday that is.Now all of a sudden, most of my family is complaining about wifi disconnects, slow speeds, etc. (My primary PC is hard-wired so I don't see any problems whatsoever... the problem apears to be wifi-only)And the Apple devices (OSX & IOS) seem to have the most severe problems. But Windows devices have also seen problems, just not as critical.Also, it's worth noting that I've been running 1.0.04 the whole time, without any problems... it seemed relatively stable to me. That is until yesterday.
I've bounced the router, I've disabled/re-enabled Wireless G network. I've switched mode from "mixed" to "G-only" back to "mixed". I've changed the channel width back to the default of Auto (I had been using 20Mhz), which increased my throughput (as measured by Qcheck) so I'm leaving it "Auto".
View 9 Replies
View Related
Feb 4, 2012
I work from home on a Lenovo Laptop. I connect to my work network, and ultimately to a midrange ISeries. For the past year I've had no major problems with my Netgear Linksys WRT54G. I switched to a Netgear N300 last weekend because my husband's desktop was having a lot of issues. His connection is much better now.I'm able to connect to the internet with no problem, and I can access my company network & email pretty well. But, when I log on the ISeries it slows to way less than a crawl. According to my netwok icon, the connection is anywhere from 104 to 130 MBPS at any given time. But it freezes up so badly that it takes about 20 - 30 seconds just to type each letter, or to go from one window to another, or just to move the cursor down one line. It's infuriating. Every once in awhile if I disconnect and reconnect it works almost normally for awhile, but eventually slows down almost to a stop again. I actually worked for about 90 minutes the other day with no problem before it started acting up again. When I put the old G router back it works fine again. My laptop has an Intel(R) Centrino(R) Advanced-N 620 wireless adaptor. As long as I don't connect to the iseries, I have good speed and no issues with the internet or work intranet.
View 1 Replies
View Related
Apr 29, 2013
I have a Linksys E1200 modem and I am only getting less than 1.0 mbps download speeds. When connected via ethernet cable to the router, my download speed is > 50 mbps.
View 2 Replies
View Related
Mar 28, 2013
I'm thinking of purchasing a Cisco Linksys EA6500. I need a router that can one monitor bandwidth used by device. Keep exceeding our ISP's network bandwidth allocation, need to identify the devices that are causing this high usage and be able to do so from the router. Does the EA6500's standard software support this, is their router software one can obtain for the unit that does this or is there another home router option that can perform this function?
View 6 Replies
View Related
Feb 18, 2012
Yesterday I had to move the computer desk to paint the wall behind it,which included unplugging the router and modem.There are four computers in the house,three on wireless, and after I hooked everything back up the pc in my room and the hardwired one reconnected to the router and internet just fine.My brother's pc and my laptop though can't seem to connect, they attempt to connect but just say they can't connect.
I work at the Staples Easy Tech center and the resident tech there told me to do an IP flush or some such thing, but my google fuu is weak and this "ipconfig /release" and "ipconfig /renew" refuse to do anything without a connection to the network.I proceeded to hardwire my laptop and even then it says no internet connection and doesn't recognize the network. I already power-cycled the router.Maybe power-cycle the modem?Reset mac addresses?
View 14 Replies
View Related
Aug 3, 2012
I had some issues with network and I thought that reseting the modem might work. So I did it, I pushed the reset button thingy, but now I can't connect wireless. There is no network offered in "Wireless network connections", like the reset deleted it. What can I do about this?
View 2 Replies
View Related
Dec 22, 2012
I have 3 Wireless Devices connected to my Router which is a Ipad, Ipod Touch & laptop.I have 2 hard Wired conneted to my Router which is a ps3 and a Desktop. How can i have great speeds and reliable connection on all of them.
View 9 Replies
View Related
Jun 5, 2012
I have opened my NAT for xbox using Port Triggering , but I cannot open my NAT for the PC because it uses no ports!I cannot host a match using any MMO game , and I cannot host any MW3/Black Ops matches too!
View 7 Replies
View Related
Aug 12, 2012
Setting up new E1200 wireless router. Used the CD to setup network. It set up two networks: 1 secured and one unsecured guest network. Ican connect wirelessly to guest network no problem but it will not connect to the secured network using the correct security key (password).
View 9 Replies
View Related
May 1, 2013
I purchased E1200 and have a problem. I have static external IP but router configured to get IP automatically (reservation from ISP). When some one at home using internet I can commetc to the router using remote management. But when everybody out and no internet users at home I cannot connect to the router. I checked with other router from linksys (old one WAG45G or something like this) and it was the same. But it works great whith TP-Link routers.
View 4 Replies
View Related
Nov 7, 2011
I have a Panasonic Visio tv, I have a LINKsys E1200 that is connected to my Cable Internet. I have successfully connected the wireless to my laptop and have a guest network that has been tested and works as well. I bought a Sharp Blu Ray player that has wireless capability connected to the TV with HDMI cable and the LAN adapter is in the player. When I had the Blu Ray downstairs I had it connected to the LINKsys thru an ethernet cable and didn't use the adapter, but I wanted to take it upstairs and use it on that TV. CANNOT establish an internet connection?
View 2 Replies
View Related
Jan 4, 2012
Is it possible to use a Linksys E1200 as a repeater? If so, how do I set it up?
View 3 Replies
View Related
