Can't Connect To Internet / Router After Modem Reset?
Feb 18, 2012
Yesterday I had to move the computer desk to paint the wall behind it,which included unplugging the router and modem.There are four computers in the house,three on wireless, and after I hooked everything back up the pc in my room and the hardwired one reconnected to the router and internet just fine.My brother's pc and my laptop though can't seem to connect, they attempt to connect but just say they can't connect.
I work at the Staples Easy Tech center and the resident tech there told me to do an IP flush or some such thing, but my google fuu is weak and this "ipconfig /release" and "ipconfig /renew" refuse to do anything without a connection to the network.I proceeded to hardwire my laptop and even then it says no internet connection and doesn't recognize the network. I already power-cycled the router.Maybe power-cycle the modem?Reset mac addresses?
I have reset the modem but after resetting it I can't go for internet anymore with computer or wifi . And after that I notice that my wifi is not under any security which is free for all.can I know how to fix this problem ?the main problem is mostly that can't go internet after reset it
i was having issues with one of my devices after a power outage. all my other devices worked (laptops, xbox, iphones, etc)i thought doing a reset on the router would get the odd device working again but all it did was mess up my internet. i don't have the key or cd any longer from when i set it up.
For several years I was connected to the internet via a USB modem (with TalkTalk being my ISP), however, after purchasing a laptop with Wi-Fi for my partner's daughter, decided it was time to get a router so we could all use the internet.I purchased a Netgear N150 Wireless ADSL2+ Modem Router, model DGN1000, connected (via ethernet as the desktop has no wireless receiver) and installed it as per instructions supplied.However since that point I have been unable to connect to the internet on my desktop through the router. Wireless devices (several laptops, iPhones and games consoles) have no issues whatsoever in connecting and using the internet.
At first the desktop kept saying that I had "limited or no connectivity" which I eventually sorted out, there was some kind of issue with my IP address, but I can't remember what now. Now I when I try to load any website, Internet explorer tells me it couldn't load the page due to .... Google Chrome is more specific and tells me that the DNS lookup failed. I have tried updating the ethernet controller driver, using the 'flushdns' command, and after discovering many other people on TalkTalk tech forums having similar DNS issues, tried using DNS addresses that were suggested by both their support staff and members of the public (i.e. Google's DNS 8.8.8.8), and still nothing. If I reconnect my USB modem I can connect to the internet no problem, but I'd prefer to only have one modem on the go.I am running a HP Pavilion with Win XP (SP2), and all the laptops that have connected wirelessly (including the one I'm using now) are running Vista.
Last night Comcast reset our modem (from afar) so we could get a free movie to work. After that, we got the movie but my wireless internet now does not work. I can connect when attached to the cable modem but when I plug into the router I don't have access to internet.The router is plugged in and all lights are working (it acts normally otherwise). Also, our landline phone (which is in the bundle of the cable connection) does not work either.Comcast is willing to look at the phone but refuses to get involved in the wireless thing.What the heck is wrong?
I can connect to the Internet when my laptop's connected directly to the modem but not through my wireless router. My laptop can connect to the router, but then I have no Internet access. (I've tried resetting my router and modem.[CODE]
My wireless was working but would load some pages super slow and others just fine. I reset my modem and router and now I can wireless connect to the router but get no connection. If I plug my computer directly to the modem I can connect the internet just fine. But if I hook up my router and connect it to my pc through a cable it can't connect just like the wireless.I have a linksys WRT54GSv1 Comcast is my ISP I ran Xirrus connection test and it said DNS Lookup Failure then No IP Availible.This is an ipconfg /all result
Code: Microsoft Windows [Version 6.1.7600] Copyright (c) 2009 Microsoft Corporation. All rights reserved. C:Users**********>ipconfig /all
I set up an E1200 about two weeks ago to replace our old DI-524 because our net speeds were getting throttled (the old router wouldn't support anything higher than 10mbps). The same day, we started getting modem resets (We have an SB6120). This never happened on the old router but it's constantly happening with this new one. It'll happen multiple times a day. I called Cox Tech Support and they pushed an upgrade onto the modem but it still reset. I don't think it's the router, since I don't understand why it would force the modem to reset, but this never happened before I installed it. The firmware is updated to the latest version on the Cisco site (1.0.02).
I'm having trouble connecting my 02 dongle to the internet using my router. My router is a TP-LINK MR3420 and my 02 modem device is E1752. I checked to see if the modem is compatible and it says it is. I went through the configuration that was given to me with the router and I tried using you tube but nothing. Do i need to get a static I.P address off my Internet provider? If I plug my 02 usb dongle directly into my computer it works perfectly and I got the router to work using a ethernet cable and plugging it into the WAN port at the back of the router but I would prefer to let it connect through the 3g port. I get a connection at 40% and 100 bytes are sent and some are received but the connection drops. Is it a problem with the connection? I will upload a image.
Cannot connect to Internet. Have a Netgear DGN2000 modem-router. Using XP Pro, AT+T ISP.Get to 'admin','password' page and sometimes get to Setup wizard but never able to finish it.AT+T checked line and said it was OK. Took all filters off phone lines and only have phone jack with router hooked up to it, so no interference is there. Just have DSL, 'dry loop'.Lights on router are (Green)Power,(Green) Port, (Green)Wireless,and (Green)blinking DSL, (RED) Internet light. When I leave router on these are the lights. Must turn router off so I can use Netgear unsecured network for internet on a wireless laptop running Vista.
I reset my Hybrid modem router's settings back to factory settings cause the disconnects were pissing me off.After a while, It disconnected. I tried reconnecting, but now it's only showing "No Internet access."
So I recently just built a new pc for gaming, I can't seem to connect to the internet through my router or directly through my modem. I have connected directly on my laptop and it works and through router and it works.
Sometimes my wifi signal will randomly drop and I cannot browse the Internet. The network still appears on my computer and I can connect to it, however Internet pages will not load. This lasts for hours, sometimes days. If I unplug the modem from the router and connect directly to the modem via Ethernet, everything works fine! I have tried unplugging everything for 1 minute then plugging it back in and it does nothing.
I've decided to set up a home network - my first attempt at setting up a network, but have run into a problem;I've bought a Linksys HRT54GL routers and connected it to a Cisco EPC2325 modem. I run the setup wizard and everything is going well until the router tries connecting to the internet when a pop-up appears telling me that it can't connect to the internet and that i should try turning my modem off and on again.
Tried numerous times but no Internet connection between Directv hr23-700 and Netgear DSL 7550 modem/router. Is connected to home network, but no Internet.
I recently changed my internet connection to DSL from Cable, so now I'm using PPPoE type of connection.
Right now my router is configured as Automatic DHCP with the modem doing the PPPoE connection. All is fine and well.
Since I own a PS3, and Nat Type 3 conection is really bad for my online gaming, I would like to bridge my modem and connect to the internet through my router. That way I can properly forward my ports, use QoS and effectively get a better connection on the PS3.
I was able to successfully bridge the modem, but the PPPoE config on the router isn't able to connect to the internet.
Modem and router have been reinitialized after the configurations were changed. I do have the username and passwords, and they were properly put on the router.
I am with Virgin media and have a home lab (2611 routers, 3550 switches, 2950s etc) which i usually just use for testing things on and practicing.
Now I tried to connect it to the internet and got some weird things happening.
I got NAT and DHCP client all setup correctly on the router (or so I think!) along with DNS settings but I still can't get Internet access.
My network is all setup right so that through using OSPF the router is the gateway (0.0.0.0 route) for all devices. Doing a traceroute confirms this.
Yet I never get any further than the router? I see IP nat translations ticking up as I send more requests but never get a webpage or a reply from any of the machines in my network.
HOWEVER... The router itself does get some replies from Google.co.uk and bbc.co.uk but doesn't seem to want to give anything else on the "inside" a response?
Here is a dump of config:
version 12.4 service timestamps debug datetime msec service timestamps log datetime msec
I wanted my latptop to be reset so I could give it to a friend. Everything worked fine before I ran the OS disk. Now I try to connec to the internet and it wont work. The message "this computer does not have a wireless network adapter installed and configured" popped up. So I tried to plug in a an ethernet cable and it still wont let me connect to the internet! In my device manager bar under other devices a network controller is there with a yellow excplanation point. So I was going to go to the dell link provided in another forum and update the drivers, but I cant do that if I cant connect to the internet at all! My laptop is a dell inspiron 1545.
My Motorola SBG901 Modem/Router combo has stopped connecting to the internet. I have done all the troubleshooting with Comcast and with Motorola and it is out of warranty, so I will have to purchase a new one.In the mean time, I wanted to use it only as a wireless router connected to my Scientific Atlanta DPC2100R2 modem. Is there anyway to do this? Is there a way to disable the modem in the SBG901? Simply connecting with the ethernet cords has not worked. I connected the DPC2100 to the SBG901 via ethernet cord. My computer was able to pick up a wireless connection but there is no cable connection.
I have a cable modem installed to my property but want to use my modem/router to go wireless. The proble is my cable modem output is a RJ45 and the router input is RJ11.
I am in the process of opening an internet cafe. I dont know exactly what a pc server does on the network... or do I really need one? Is the switch/hub sufficent to connect all pcs to the moderm to connect to the internet?
I had some issues with network and I thought that reseting the modem might work. So I did it, I pushed the reset button thingy, but now I can't connect wireless. There is no network offered in "Wireless network connections", like the reset deleted it. What can I do about this?
I've been having this problem the past 2 days. around 7-7:30pm my motorola sbg6580 will reboot itself every 15m or so the rest of the night.I've checked all my line they are in good condition, I've done the whole pull out all the cords let it sit for 1 minute, I've factory reset it.called the cableone tech support and it even reset while i was on the phone with him. I have a tech coming out tuesday but if it's something i can troubleshoot and fix now i'd rather have that.
Every time I switch on one of our laptops it will not connect, once the router is restarted it works fine. We have 4 other devices which happily connect to the wireless connection first time.
We recently upgraded to higher speed internet and were to "reset" our modem, which is PCI Soft Data Fax Modem With SmartCP.How does one "reset" their modem?
I need to reset my DLink wireless modem all over again, can't get it to recognise the router, so thought that it would need to reset to factory defaut, how can I do this. Tried just hitting reset on the router,but nothing is happening.
I have an acer aspire 5315, windows vista,32 bit operating system.I recently got a new modem/router (it's apparently 2in1 from rogers) and I cannot connect to the internet. When I attempt to connect i can only connect to the "local" connection. Everyone else in my family can connect via wireless and I can only connect if i use an ethernet cable which is directly connected to my laptop.When i typed in ipconfig/all on the command prompt this is what pops up :
Microsoft Windows [Version 6.0.6002] Copyright (c) 2006 Microsoft Corporation. All rights reserved. C:Windowssystem32>ipconfig/all
when i pluggled in my ethernet cable, it started to disconnect from internet after a few seconds.In a desperate attempt i pressed the small reset switch on the modem but as from then i could not connect to internet at all. Could reset have changed some settings?Do you think the problem could be just the isp blocking me for some reason?
my problem is that my old modem is connection to the internet i got a new one few days ago DLINK 2750 u ,it wont connect the adsl light is stable every thing is ok , the password and the username are correct . it wont connect at all i rest tried again and again and again.
