I have an E1200 and if a device - such as my tablet or laptop - is left unused for a period of time - say for 4 or 5 hours - they won't reconnect to the router unless I do a power cycle/reset on the router.
View 5 RepliesWe have a Model WRT54GLWireless-G router. At least once a day it loses it's internet connection. All computers that are wired to the switch that is connected to it lose their internet as well as any wireless devices. I have to manually power-cycle the router to get internet back.
View 9 Replies View RelatedI have installed my new E4200 and it works beautifully. I have several wirelss adapters and a few wired connections through powerline adapters. I also have a second VPN router attached to the 4200.I can see the wireless connected devices with the associated IP addresses. If I plug a laptop directly into the Cisco, I can of course see it.However, I can see none of the devices attatched to the powerline devices? I have a securty cam connected via the powerline and want to know the IP address. I checked with cisco technical support via chat and they said it is impossible. I have used 2 previous routers with the same configuration and can see all devices.
View 1 Replies View RelatedI am trying to setup two wireless routers in my network. I purchased a E1200 N router and an older G Linksys router upstairs.When I got the N router I set it up a stand alone router and it worked great for a week or so. I then wanted to try to get both routers going to I changed the IP address on E1200 to 192.168.2.1....the router rebooted and then could not login. I am not able to get any internet conntion anymore. When I type 192.168.2.1 it goes to page can not be displayed, 192.168.1.1 same thing. Ipconfig shows some address auto address that I did not put in and i am also not connected to a modem. I cant log into the router at all.So reset: I held down the button for 30 seconds...let go and it blinks and then goes solid but does not reset. Unplugged router for 5 minutes tried again. Cant get into 192.168.1.1..will not prompt for anything. I have tried to reset this router about 10 times and can not get into the default login at all.
View 1 Replies View RelatedIt seems there's no way to reboot this device from the browser interface. You have to actually go and recycle the power by physically pressing the button.Plus, to setup Port Forwarding you have to reboot the modem.This is a major problem because it means you have to be on the premises to change things like the port forwarding. You setup it up, but have to reboot for it to take effect.
View 1 Replies View RelatedI set up an E1200 about two weeks ago to replace our old DI-524 because our net speeds were getting throttled (the old router wouldn't support anything higher than 10mbps). The same day, we started getting modem resets (We have an SB6120). This never happened on the old router but it's constantly happening with this new one. It'll happen multiple times a day. I called Cox Tech Support and they pushed an upgrade onto the modem but it still reset. I don't think it's the router, since I don't understand why it would force the modem to reset, but this never happened before I installed it. The firmware is updated to the latest version on the Cisco site (1.0.02).
View 5 Replies View Relatedsince last nite my router E1200 has been having speed up and down problems.first it goes to 150mb/s then back down to 1 for a few minutes, usualy its stuck at 72mb/s which is a far cry from its rated 300mbps but qi'd rahter have that than 1-2mbps.i'd be happy with 150mbps but that only lasts 5mins then goes down to 1-2mbps and i have to reset my connection.
View 9 Replies View Relatedrecently bought a new Linksys EA3500 that is connected to my SB5120 cable modem. For two weeks it's been running smoothly but when my cable modem is in need of a power cycle.I power cycle both the router and modem but my connection is lost. it's after countless hours of messing with the two I'll get the connection back but I'm afraid it'll lose connection again, that and I fear I may have enabled bad options.
View 10 Replies View RelatedI have the E1200 and since I installed this router, the wireless download speed on my iPad and iPhone has been only around 4 to 5 Mbps when my other wireless devices could get to 7 Mbps and ethernet gives close to 10 (my ISP gives 10 Mbps max).I know many people experience slow download and normally disabling the WMM would solve the issue. But this doesn't work for me and I've made sure i'm on the latest firmware.
View 5 Replies View RelatedI have a Cisco 1841 Router with ADVANCE IPSERVICE IOS .The said router does not safe config, even after saving the config? As soon as the power cycled all the config will be lost? what can be done to correct this ?
View 1 Replies View RelatedI was trying to do a hard reset and power went off. Since then if i plug in electricity in my router all lights lit once, then all turn off.
View 4 Replies View RelatedI have a E1200 router and it's pretty good however I've noticed that there are 12 devices connected to my router when infact there should only be 4 devices connected. I would like to see all the devices that are connected and disconnect the ones that don't belong
View 1 Replies View RelatedI have the following equipment
1 x AIR-WLC-2106-K9 (IOS = 6.0.199.4)
4 x AIR-LAP1131G-E-K9 (IOS = 12.4(21a)JHB1)
All configued ok with 2 SSID's associated to 2 VLANS all operates as expected.However every few 2 to 12 hours the WLC crashes, locks up.Unabale to contact via telnet or browser, will not respond to ping.The LAPs remain up but the WLANS go off air etcOnly a physical restart of the WLC will bring it back.
I'm having a little issue with some Cisco Aironet1242ag WAP's. I receive a call at least twice a month stating that some of the WAP's are not giving out internet connection. What I always do is go to my patch panel and disconnect those WAP's not working and connect them back again so they can power cycle. These WAP's are connected to a Cisco3750g. Once the WAP's boot up, the users can connect to the WAP and connect to the internet.
I don't know if these WAP's are filling up with some information that causes the access points to not connect to the WAN.
Our wireless network has started to drop out periodically. If we pull power and restore, the network immediately comes back up on all our our devices. We have the WRT54G, and we have 2 PCs, 2 Macs, and 3 iPhones, and a wired home phone. Normally there are not this many devices connected, but with everyone home for Thanksgiving and all these devices on the network we have started to see this issue.
Are there simply more devices than the router can handle? Is one of the devices crashing the network for everyone? What typically will cause something like this?
We have some 1242 LAPs in a two 5508 controller setup working fine. All LAP are configured to obtain address from DHCP. After first join we usually change some configs like HOSTNAME, AP GROUP, PRIMARY AND SECONDARY WLC. After a software restart or a complete power off/power on the LAPs joins the primary controller and all configuration still there. We now add a 1142 LAP and is does not retain the configuration after a power off/power on cycle, but after a software restart there is no problem. The only way to retain the config is setting the AP with a static IP address.
We use WLC 7.0.116 and we see no errors in the LAP console.
I've just bought a pair of WAP121 for testing and validation. I've set it up properly (user/password, IP, management vlan, NTP, SNMP, 802.1x, etc). So far, so good, everything worked as expected. I've downloaded the configuration to my PC, and also saved it to startup-config. I've powered off the unit, went for a coffee, and powered it back. All my settings were lost.
Tried to restore settings from the file downloaded to my PC, but no luck. After reboot, it was factory clean, no trace from settings in the backup file. I've set it up again by hand, power cycled it, and the **** thing reloaded to default settings.
Faulty unit, I thought, so I opened the other one I have, and repeated the whole thing, but same results. Test were made using the power adapter supplied but also tried with a catalyst 2960 with PoE.
I have access controls setup on my DIR-825 which work fine until there is a power outage and my router comes back up.I am using Automatic Time Configuration and have the NTP server set to ntp1 [URL]When the router comes back up I checked to make sure the NTP server option is still enabled, and it is, however the current time is totally wrong.To fix this I had to go to the pull-down, select 'ntp1.dlink.com' and then save the settings. After this the time is correct again.This is as bad as not having the Automatic Time Configuration option at all, since I can't guarantee that the power won't go out. I do not have a UPS hooked up to back up the router, nor do I see why I should need one if the Automatic Time Configuration actually worked.know if there is a way of making the Automatic Time Configuration reliable so the time on my router is automatically corrected when the power comes back up?
View 3 Replies View RelatedI've setted the unit in BRIDGE MODE, and attached on it 3 LAN devices, 1 PC Desktop, 1 NAS WDBE and 1 HP printer ... OK all config process was right and all my units talk togheter via AP Netgear DNG2000, and so i can use for instance the printer with my laptop too connected in WI-FI N. Now usually, In the night I turn off all my devices (DAP included), and when in the morning I need only the printer used by my laptop, obviously I turn on ROUTER - BRIDGE - PRINTER - LAPTOP but NOT the DESKTOP ... and so the DAP can't reconnect automatically to the router (both the lights AP/BRIDGE are on and fixed) ... I turn on the PC and the BRIDGE reconnect to the world .... BUT I DON'T WANT turn on everytime the desktop !
1) all gears has fixed IPs
2) DHCP server deactivated on the AP main router (DNG2000)
3) no WPS used, only WPA2-PSK (AES) personal keys on all gears
once that DAP-1522 is connected to the router .... all work fine (also when I turn off the DESKTOP).so the workaround is never turn-off the DAP ? I can't believe ... and who will save the energy planet
Cisco 2800, 12.4(23b) router has two VPN tunnels to other Cisco devices.
Authentication uses certificates from a PKI CA server. Under normal circumstances all works fine, both crypto sessions up.
After a power cycle (having first saved configs) however, the crypto sessions are stuck in DOWN-NEGOTIATING.
The certificate on the router still looks valid.
The only way to get the sessions back up is to renew the certificate, which seems strange as the existing one appeared to be still valid.
When our DSL modem drops its connection, even momentarily, the RV220W requires a power cycle before the computers on the LAN can browse again. When I connect to the router, the WAN Information displays the word Connecting, rather than Connected.
We have a DSL modem connected to the router, the router connected to an ethernet switch, and our small business pc's connected to the switch.
Firmware on the router is 1.0.4.17
Setting up new E1200 wireless router. Used the CD to setup network. It set up two networks: 1 secured and one unsecured guest network. Ican connect wirelessly to guest network no problem but it will not connect to the secured network using the correct security key (password).
View 9 Replies View RelatedI have a Panasonic Visio tv, I have a LINKsys E1200 that is connected to my Cable Internet. I have successfully connected the wireless to my laptop and have a guest network that has been tested and works as well. I bought a Sharp Blu Ray player that has wireless capability connected to the TV with HDMI cable and the LAN adapter is in the player. When I had the Blu Ray downstairs I had it connected to the LINKsys thru an ethernet cable and didn't use the adapter, but I wanted to take it upstairs and use it on that TV. CANNOT establish an internet connection?
View 2 Replies View RelatedI replaced my broken modem with a new Motorola 3360 as recommended by my ISP. The new modem works fine connected directly to my PC. When connecting the modem to the Cisco E1200 router, the same one I had with the older modem, the E1200 says I'm not connected to the PC. I've triple checked the wired connections from the modem to the router and then to the PC. I've swapped out cables and verified that they all work when used directly from the modem to the PC. I'm thinking some settings from the old Westell modem are messing with the connectivity of the new E1200 router.
View 2 Replies View RelatedI just installed an E1200 router and used the CD to take care of the software work. I Cannot connect to it by WiFi. I still have to use a cable connection.
View 4 Replies View RelatedIn one area of the home is a century link pk 5000 modem that connect to the internet. In another area of the home is the computer that has an e1200. Is it possible to connect the computer to the internet, wirelessly, from the e1200 to the pk5000? How is this accomplished?
I know the settings for the pk5000 and would "input" them into the e1200 if I friggen knew where to do this.
We have just installed the E1200 wireless router. We are able to access the internet from our home computers, however we cannot get the IPAD connected. When we try to find our wireless network to connect to it doesn't display yet our we can still see our neighbors wireless networks.
View 1 Replies View RelatedI just bough Linksys E1200, downloaded setup software, ran it, all setup went fine, no errors, but at the end I got the screen saying that can establish internet connection.The steps are totally simple. Did exactly as instructed.'Modem, connected to a PC directly give internet no problem.Modem, connected to the router, and router connected to PC - no internet.And... It's all wired at this moment, all connected with network cable.
View 9 Replies View RelatedI received the Linksys E1200 today and I installed it according to the instructions but at the end of the installation it showed the message "No internet connection." I restarted the router + modem but that didn't work at all
View 4 Replies View RelatedWhen I first set up my router, I used the same user name and pw as I had for my old router and my iPhone connect just fine. I decided to use the guest network after one of my sons friends was sitting outside one morning using my network. I told the friend the pw for the guest and changed the pw for my network and created an key on a thumb drive. Now I cannot connect my iphone. When I try to use guest is seems to work ok, but I want to use my network. I chose my network on my iphone and it simply says unable to connect. That is the only info/choice I am given.
View 1 Replies View RelatedI can connect to the wireless network, but cannot connect to the internet. The guest can connect but not the main user.E1200..Win7SP1.
View 1 Replies View RelatedLinksys E1200. I cannot connect to the Internet through my primary connection, but I can still connect through the guest connection. I think I know what happened, but I don’t know how to fix it. A connect / disconnect key on my keyboard is located right next to the mute sound key. I wanted to mute my sound, and when it didn’t mute I pressed the key a couple more times before I realized I was pressing the wrong key. So I’m guessing I probably messed up some settings. But I don’t know if on the computer, router, or both. Per the documentation I thought I might be able to fix it with Cisco Connect, but it wasn’t installed on my computer. There were only 3 Cisco modules installed.. EAP-FAST module, LEAP module, and PEAP module. I managed to find Cisco Connect on the website and downloaded it, but still couldn’t fix the problem.
View 2 Replies View RelatedI just upgraded my router from an old wireless54G to an E1200.The wireless device I have on my Sony Viao PCG GRT-240G laptop is LAN-Express AS IEEE 802.11g miniPCI Adapter
-Initially I couldn't connect at all with this machine (however the other two newer laptops could) so I contacted the Linksys tech and he advised I should upgrade my laptop driver
-After much research about this I found a common fix was to upgraded drivers from the 2004 sony driver to atheros_wifi_9.2.0.480 drivers.
-After I did the upgrade I can connect to the router on the guest account and use the internet
However, on the Main account I can connect to the router but I have no internet connectionGoogle chrome gives error belowThe server at [url]... can't be found, because the DNS lookup failed. DNS is the network service that translates a website's name to its Internet address. This error is most often caused by having no connection to the Internet or a misconfigured network. It can also be caused by an unresponsive DNS server or a firewall preventing Google Chrome from accessing the network.How can I use one part of the network but not the other part? Shouldn't both the guest & main accounts use DNS lookup?