D-Link DAP-1522 :: Didn't Reconnect Auto After Power Cycle
Jan 20, 2011
I've setted the unit in BRIDGE MODE, and attached on it 3 LAN devices, 1 PC Desktop, 1 NAS WDBE and 1 HP printer ... OK all config process was right and all my units talk togheter via AP Netgear DNG2000, and so i can use for instance the printer with my laptop too connected in WI-FI N. Now usually, In the night I turn off all my devices (DAP included), and when in the morning I need only the printer used by my laptop, obviously I turn on ROUTER - BRIDGE - PRINTER - LAPTOP but NOT the DESKTOP ... and so the DAP can't reconnect automatically to the router (both the lights AP/BRIDGE are on and fixed) ... I turn on the PC and the BRIDGE reconnect to the world .... BUT I DON'T WANT turn on everytime the desktop !
1) all gears has fixed IPs
2) DHCP server deactivated on the AP main router (DNG2000)
3) no WPS used, only WPA2-PSK (AES) personal keys on all gears
once that DAP-1522 is connected to the router .... all work fine (also when I turn off the DESKTOP).so the workaround is never turn-off the DAP ? I can't believe ... and who will save the energy planet
View 2 Replies
ADVERTISEMENT
Nov 27, 2011
I have access controls setup on my DIR-825 which work fine until there is a power outage and my router comes back up.I am using Automatic Time Configuration and have the NTP server set to ntp1 [URL]When the router comes back up I checked to make sure the NTP server option is still enabled, and it is, however the current time is totally wrong.To fix this I had to go to the pull-down, select 'ntp1.dlink.com' and then save the settings. After this the time is correct again.This is as bad as not having the Automatic Time Configuration option at all, since I can't guarantee that the power won't go out. I do not have a UPS hooked up to back up the router, nor do I see why I should need one if the Automatic Time Configuration actually worked.know if there is a way of making the Automatic Time Configuration reliable so the time on my router is automatically corrected when the power comes back up?
View 3 Replies
View Related
Dec 9, 2009
I successfully linked a DIR-655 (A4, FW:1.21) via WPS.
I then updated the DAP-1522 to FW:1.21 from 1.1.
Things looked great. I then moved it upstairs to my home theater.
Plugged it in and got a blinking power light. Completely unresponsive to either linkage or 192.168.0.50.
I have followed everyone advice listed either here or in Amazons reviews. And from my own experience with similar electronics the flashing power LED is indicative of a "brick".
I have initiated a replacement shipment from amazon. Just wanted to see if anyone had seen this before.
View 3 Replies
View Related
May 6, 2013
I am working with a small off that has a 5505 acting as a basic firewall. Behind it are off-the-shelf unmanaged switches. Two users have to work with an outside vendor and are having issues. They have a Sonicwall remote VPN client on each of their desktops and use this to connect to the vendor. They then RDP into VMWare-based Windows 7 desktops at the vendor's site to do their work. Randomly throughout the day (6-10 times per day) while they are actively working the RDP session will disconnect. It will auto-reconnect after a few seconds. The VPN log on the clients never show any issues. I believe this is an RDP problem because while the RDP session is disconnecting, their VPN client is not (it is set to NOT auto-reconnect if it gets disconnected so that I will know for sure if it gets disconnected). I don't see anything in the ASA's logs about denying connections involving their PCs and the remote VPN peer IP.
View 7 Replies
View Related
Jun 13, 2012
recently bought a new Linksys EA3500 that is connected to my SB5120 cable modem. For two weeks it's been running smoothly but when my cable modem is in need of a power cycle.I power cycle both the router and modem but my connection is lost. it's after countless hours of messing with the two I'll get the connection back but I'm afraid it'll lose connection again, that and I fear I may have enabled bad options.
View 10 Replies
View Related
Aug 1, 2011
It seems there's no way to reboot this device from the browser interface. You have to actually go and recycle the power by physically pressing the button.Plus, to setup Port Forwarding you have to reboot the modem.This is a major problem because it means you have to be on the premises to change things like the port forwarding. You setup it up, but have to reboot for it to take effect.
View 1 Replies
View Related
Apr 17, 2011
I have the following equipment
1 x AIR-WLC-2106-K9 (IOS = 6.0.199.4)
4 x AIR-LAP1131G-E-K9 (IOS = 12.4(21a)JHB1)
All configued ok with 2 SSID's associated to 2 VLANS all operates as expected.However every few 2 to 12 hours the WLC crashes, locks up.Unabale to contact via telnet or browser, will not respond to ping.The LAPs remain up but the WLANS go off air etcOnly a physical restart of the WLC will bring it back.
View 14 Replies
View Related
Nov 14, 2012
I'm having a little issue with some Cisco Aironet1242ag WAP's. I receive a call at least twice a month stating that some of the WAP's are not giving out internet connection. What I always do is go to my patch panel and disconnect those WAP's not working and connect them back again so they can power cycle. These WAP's are connected to a Cisco3750g. Once the WAP's boot up, the users can connect to the WAP and connect to the internet.
I don't know if these WAP's are filling up with some information that causes the access points to not connect to the WAN.
View 7 Replies
View Related
Jan 24, 2013
I have a Cisco 1841 Router with ADVANCE IPSERVICE IOS .The said router does not safe config, even after saving the config? As soon as the power cycled all the config will be lost? what can be done to correct this ?
View 1 Replies
View Related
Apr 15, 2013
Cisco 2800, 12.4(23b) router has two VPN tunnels to other Cisco devices.
Authentication uses certificates from a PKI CA server. Under normal circumstances all works fine, both crypto sessions up.
After a power cycle (having first saved configs) however, the crypto sessions are stuck in DOWN-NEGOTIATING.
The certificate on the router still looks valid.
The only way to get the sessions back up is to renew the certificate, which seems strange as the existing one appeared to be still valid.
View 5 Replies
View Related
Aug 27, 2012
We have some 1242 LAPs in a two 5508 controller setup working fine. All LAP are configured to obtain address from DHCP. After first join we usually change some configs like HOSTNAME, AP GROUP, PRIMARY AND SECONDARY WLC. After a software restart or a complete power off/power on the LAPs joins the primary controller and all configuration still there. We now add a 1142 LAP and is does not retain the configuration after a power off/power on cycle, but after a software restart there is no problem. The only way to retain the config is setting the AP with a static IP address.
We use WLC 7.0.116 and we see no errors in the LAP console.
View 1 Replies
View Related
Jun 11, 2012
I've just bought a pair of WAP121 for testing and validation. I've set it up properly (user/password, IP, management vlan, NTP, SNMP, 802.1x, etc). So far, so good, everything worked as expected. I've downloaded the configuration to my PC, and also saved it to startup-config. I've powered off the unit, went for a coffee, and powered it back. All my settings were lost.
Tried to restore settings from the file downloaded to my PC, but no luck. After reboot, it was factory clean, no trace from settings in the backup file. I've set it up again by hand, power cycled it, and the **** thing reloaded to default settings.
Faulty unit, I thought, so I opened the other one I have, and repeated the whole thing, but same results. Test were made using the power adapter supplied but also tried with a catalyst 2960 with PoE.
View 3 Replies
View Related
Dec 9, 2012
When our DSL modem drops its connection, even momentarily, the RV220W requires a power cycle before the computers on the LAN can browse again. When I connect to the router, the WAN Information displays the word Connecting, rather than Connected.
We have a DSL modem connected to the router, the router connected to an ethernet switch, and our small business pc's connected to the switch.
Firmware on the router is 1.0.4.17
View 4 Replies
View Related
Jan 19, 2013
I have an E1200 and if a device - such as my tablet or laptop - is left unused for a period of time - say for 4 or 5 hours - they won't reconnect to the router unless I do a power cycle/reset on the router.
View 5 Replies
View Related
Aug 15, 2012
We have a Model WRT54GLWireless-G router. At least once a day it loses it's internet connection. All computers that are wired to the switch that is connected to it lose their internet as well as any wireless devices. I have to manually power-cycle the router to get internet back.
View 9 Replies
View Related
Dec 6, 2012
i have router 7200 , one of its power supply stops working , but lms 4.2 doesn't notify me?
View 6 Replies
View Related
May 23, 2009
My Linksys WRT150N recently gave up on me and started to give me weird issues and started to disconnect (all the ports including wired & wireless) anywhere from 3 to infinite number of times per day and my only solution was to remove the power chord and connect it. I tried all possible ways possible including resetting the router, stopping SSID broadcast, removing the encryption, etc, but non worked. As the router was out of warranty my only option was to take it to the dealers where they told me it would take 3 weeks to fix and God knows how much they would have charged me. But after flashing the firmware with the dd-wrt it has been almost 24 hours without a single problem and now I have the cool option of seeing who is connected to the router, etc. This is a MUST for every Linksys owner.
1. Reset the router using 30-30-30 and waited for 2 minutes for things to come back 2 normal
2. Flashed the router with "dd-wrt.v24_mini_generic.bin"
3. Reset again using 30-30-30 and wait again4. Flashed the router with " dd-wrt.v24_std_generic.bin"5.
View 3 Replies
View Related
May 13, 2010
I'm facing the following doubt regarding the AC Power Connector on the 1522 AP.We are powering up the AP through PoE, so the AC Power Connector is not used.BUT,do i have to seal/protect the connector or leave it as is?
View 3 Replies
View Related
May 28, 2011
I have recently purchased six quantities of DIR-655 for my home use. When I registered them these six product, at the end of each registration, I got the message that I will get an email confirming the registration.I didn't get any email. I have checked my email span box and filter too.
View 6 Replies
View Related
Aug 14, 2012
I have deployed 2 x Cisco 1522 mesh access point and configured both as root ap. On top of that, I have also customized the power setting for the 802.11a/n signal to value 5. However, I discovered that whenever the mesh APs reboot, the power of 802.11a/n signal to will be reset to value 1.
Thus, I would like to ask is this a norm behaviour or I have mis-configured some setting?
View 9 Replies
View Related
Feb 20, 2013
A few months ago we upgraded our warehouse from 1242 APs to 3502E APs. We changed 16 units, all in the same building. When we came in the next day we found out that they were all on channel 1 at their lowest power level. The WLC was set for auto negotiate for power and channel but for some reason it did not work. We had successfully changed they rest of the factory with the auto feature enabled but for some reason, the warehouse did not work properly. All APs have the same IOS and are they same model. We have WiSMs mounted in a 6509 chassis as our WLC.
View 1 Replies
View Related
Dec 1, 2011
We have a WLC 4402 controlling 40+ LWAPs. Is there a way to keep Tx power level assignment dynamic, but set the time of day it does it? I'd like to minimize user impact. (Firmware v. is 7.0.116.0)
View 2 Replies
View Related
May 27, 2011
I am purchasing a new DIR 600. It pings properly, but didn't access internet. I am using HP Desktop and ORTEL broadband connection.
View 1 Replies
View Related
Jun 21, 2011
ISP Virgin Media who ship DLINKS without any assistance for custom options, I seem to be having no end of trouble trying to get my DLINK615 and Xbox to play fair.In order to allow me to play my Xbox without any technical problems, or problems with other players I had to open up a few ports, been there resolved that. But, I only want to open them on one IP I want to always be assigned to the Xbox360. This IP being 192.168.0.100
I added that into the DHCP Reservation list, only to find that the Xbox failed to reconnect after being turned off and back on, I believe this is a problem with the DLINK Router, unless I am very badly mistaken.
View 14 Replies
View Related
Jun 14, 2011
I log onto other wireless networks the first time by inputting their passwords. My iphone then always automatically reconnects wirelessly to them without have to input the password again. The phone can be asleep for a few minutes or I can be gone for a month. The phone always automatically remembers & reconnects to these networks.However, it doesn't work that way with my d-link system @ home. Everytime the phone sleeps and I wake it up, the wireless connection is lost. There is no automatic reconnection. I have to input the password each time in order to re-establish the wireless link. My printer and laptop seem to stay connected. d-link settings I need to change in order to get my iphone to automatically connect all the time?
View 7 Replies
View Related
Nov 17, 2012
Region : Italy
Model : TD-W8968
Hardware Version : V1
I have a problem with my new td-w8968 router.The problem is that i can't use the reconnect function in the program jdownloader.The script is created with jd but it doesn't work!!!
View 1 Replies
View Related
Mar 10, 2013
My D-Link DAP-1522 wireless bridge is connected through a single cat5 cable from the LAN port on my PC to the 1st LAN port on the D-link unit. At the moment, it is in bridge mode, with the blue power indicator on, the orange wireless connection light flashing, and the 1st LAN port connection periodically wavering indicating that it is communicating with my PC. When I attempt to configure the DAP-1522 via my internet browser, (IP 192.168.0.50) I get an error saying that the requested webpage does not exist.
View 6 Replies
View Related
Sep 30, 2011
I recently had a networking guy set up a VPN for me, but for it to work properly he had to change all my IP addresses to 192.168.10.xx from 192.168.0.xx. My DAP-1522 (in bridge mode) continued to work but I am unable to log on to it, I think because it's address is 192.168.0.0. I have run into some other issues which makes me think I may need to upgrade the DAP-1522 firmware and/or assign it an address beginning with 192.168.10.xx, however I can't log on to the bridge. (Nor do I know how to change or possible reassign the DAP-1522's address through my router, a DIR-615).
View 5 Replies
View Related
Apr 26, 2011
My problem is two-fold:
1. the DAP-1522 will not connect to the 5GHz network of the DIR-815. Although, this doesn't surprise me as none of my 5GHz-capable devices see it, other than intermittently and at low signal. It is most likely an issue with the 815's 5GHz radio/network.
2. OTOH, the 1522 does appear to connect to the 815's 2.4GHz network just fine. However, there is no Internet access for any of the devices connected to the 1522's ports.
I know the 1522 can work correctly on 2.4GHz, as it previously did fine with my prior 2Wire router from AT&T. (I've just switched to Comcast, using the DIR-815 connected to their SMC modem.)
Also, I know the router and modem work fine (at least with 2.4GHz), as all of my wireless devices connect easily and with screaming bandwidth to the router and Internet.
View 4 Replies
View Related
Mar 12, 2012
I have a WIN XP desktop which I successfully connected to the 1522 AP - as evidence of the GUI to program it. I have the 1522 set to Bridge Mode via the switch on the unit. The 1522 has hardware version B1 and Firmware version 2.000. I joined my wireless network successfully as evidence of the Status page showing it's successfully connected and bridged to my network. I then disabled my USB wifi NIC in hopes of using my hardwired connection to the 1522 to get on the internet.
Wireless Radio : Enabled
Bridge State : Connected
MAC Address : fc:75:xxxxxx
802.11 Mode : Mixed 802.11a, 802.11g and 802.11n
Band Width : 40
Channel : 6
Network Name
(SSID) : cleveland
Wi-Fi Protected Setup : Enabled
Security : WPA2-PSK
View 3 Replies
View Related
Dec 7, 2011
I have dap-1522 version A Browser IE8 with lestest updates.
I downloaded the DAP1522_FW_1.31zip went I try to upload via the 1522 admin error not correct file.
I try three different way to download it, could the file be bad on dlinks web site?
View 4 Replies
View Related
Aug 27, 2010
I have just discovered after three weeks of testing that DAP-1522 wireless bridges are not compatible with all the new Pioneer AVR's that support internet radio and Iphone control. Anytime a DAP-1522 is powered on and on the same subnet mask as a Pioneer receiver it will cause the Pioneer to loose it's connection every 30 minutes. The receiver is then not able to connect unless it is powered off and on again. The DAP-1522 will cause this even if the Pioneer is hardwired to a router and nothing is plugged into the DAP-1522. This affects all new models of Pioneer receivers including the Elite line like I have.
I have tested this with 3 differnet Pioneer receivers and 2 DAP-1522's and always got the same results no matter what the settings were and with the 1522 in AP or bridge mode. Other Pioneer receiver owners experiencing constant disconnect problems on another forum have now also confirmed they have DAP-1522's.....and they are also pissed after spending countless hours troubleshooting.
I talked to Dlink support today and they will not admit to a problem so I can't wait to contact Pioneer tech support on Monday to let them know I have found the reason they are seeing returns on their new receivers (some cost as much as $7K) since many of the new owners like myself are exchanging them thinking they got a bad one. I'm sure Pioneer will test this immediately and force a Dlink fix or turn it over to the FCC.At this point I just wish I could get my money back since I have also already confirmed that a netgear bridge works just fine. Come to think of it, I know Dlink has a new refund policy, but I will check with my state district attorney to see if they can legally keep my money even if the product doesn't work. I don't see anything on the outside of the box with this policy so therfore I wasn't given fair warning of the policy before purchase and would not be expected to know it since it is not industry standard. Let the games begin.
View 14 Replies
View Related
Mar 14, 2012
I just purchased a DAP-1522. The sticker on the bottom says it's a version B1, with firmware 2.0.In the web interface, it says: "Firmware Version : 1.21 , Fri 26 Jun 2009"I downloaded the 2.01 firmware from the D-Link site and when I try to upload it, it says it's not an image file.
View 11 Replies
View Related
