D-Link DAP-1522 :: DIR 655 - Blinking Power Light
Dec 9, 2009
I successfully linked a DIR-655 (A4, FW:1.21) via WPS.
I then updated the DAP-1522 to FW:1.21 from 1.1.
Things looked great. I then moved it upstairs to my home theater.
Plugged it in and got a blinking power light. Completely unresponsive to either linkage or 192.168.0.50.
I have followed everyone advice listed either here or in Amazons reviews. And from my own experience with similar electronics the flashing power LED is indicative of a "brick".
I have initiated a replacement shipment from amazon. Just wanted to see if anyone had seen this before.
View 3 Replies
ADVERTISEMENT
Aug 21, 2012
I have a Thomson TG784 router and i have a problem with it. once i turn on my rouet, and no cables are plugged in, except the power one, the two lights start blinking. The Power and the Ethernet ligh blinking. Once i connect my Ethernet cable and my DSL cable, the light are still blinking with no changes... What should i do?
View 1 Replies
View Related
Oct 29, 2011
the power light on my wrt54g v2.2 router keeps blinking and it wont connect to the internet when connected
View 3 Replies
View Related
Jul 4, 2006
My Wireless-G WRT54G router has a blinking power light and the startup software says "Unable to connect to the Router! Check that the Router has been connected to the computer, and that your Ethernet adapter is working." I tried uploading the firmware but I can't get to the router page to update. Is there a known problem or solution here or am I just going to have to find the router page?
View 9 Replies
View Related
May 11, 2009
So I recently upgraded from a WRT54GS to a WRT160N v2, all was well and good for about 3 days. Then I would lose my internet connection every 5 minutes or so, it would fix itself by the time I could open up command prompt and start pinging to pin point the problem. I decided I would update the firmware to see if that would fix the issue. Since doing that the power light has been blinking non stop. I've tried restoring it to factory defaults by holding the reset button for 30seconds, turning it off for 2 minutes and back on. That little blue light just keeps flashing. I can't even access the router setting page using 192.168.1.1. My OS is Windows xp x64 sp2, and I have DSL.
View 9 Replies
View Related
Oct 29, 2011
I need fixing my router. I updated the firmware and it said the upload has failed ever since then:
-the router doesn't work
-blinking power light
-DMZ light doesn't turn on
-can't access 192.168.1.1
My router is a WRT54G v5
View 9 Replies
View Related
Feb 3, 2012
the power light on my wrt54g v2.2 router keeps blinking and it wont connect to the internet when connected, what should i do?
View 1 Replies
View Related
Feb 20, 2012
No download available and none available via Linksys Live Chat or FTP and having spent the best part of the week trying to find relevant firmware on other forums I decided to come here to get answers to the following questions, hopefully from version 1.0 experienced owners or not.
#1. Can the firmware of version 2.0 and 3.0 be reduced to flash version 1.0?
#2. When diagnosing the blinking power light issue by connecting directly to the router and the network card using "ping -t 192.168.1.xxx" which network address do I use, 192.168.1.1 or 192.168.1.2 to 2xx?
I get a reply using 192.168.1.1 but I'm not sure that works when using the TFTP Utility if it's the wrong address on my Laptop to ping?
View 7 Replies
View Related
Feb 21, 2012
I have a Linksys WRT54GS vers 7.2 Router on an iMac OS X Leopard. The other day I was in the middle of downloading an upgrade for the router when Firefox gave me this message: "Firefox can't find the server". I was no longer able to access the internet, and the router's green power light was left flashing. It flashed for over 24 hours. I tried unplugging the router and shutting down the computer, then plugging in the router and turning on the computer. (I don't have a modem.) The light was still flashing. I tried pressing the logo button for 5 seconds. Still flashing. Tried pressing the reset button in the back. Still flashing. 'I can't get on the internet or into the router. Linksys live chat gave me a link to "Upgrading the router’s firmware using the TFTP utility", which involves a download, but I can't download anything because I can't access the internet.
View 8 Replies
View Related
Mar 24, 2011
I've seen related to flashing power lights on the router involve fixes via firmware upgrades off a PC.I'm on an iMac os 10.6.7. The WRT54 used to work as a wireless modem a couple of years ago. Tonight, it doesn't. power light blinks. Can't access any webpage interface for the thing. Reset, power down, computer restart, cable modem turn off don't change anything. Is there anything that can be done other than tossing the linksys? If that is the only option, are there wireless routers more suitable for a Mac?
View 4 Replies
View Related
Aug 15, 2011
If I conact from the modem to the pc I have internet so it must be the router. The power light is blinking along with all the port lights. Power light is blinking one time slow 2 fast. Have tried holding the reset button for 30 seconds and unpluging for 30 seconds. Can not go to the ip address it times out. New firmware is not avalible.
View 9 Replies
View Related
Feb 19, 2011
Unable to stop the power light from blinking on a BEFSR41 tried updating the firmware.I have tried resetting the router using the rest button, for 3 seconds, 10 seconds, and 30 seconds, nothing works.Tried running the setup disk, but it does not see the router. Is there a repair tool that I can download?
View 4 Replies
View Related
Apr 22, 2009
My wireless router is WRT54GC ver2.0. When I plug the power cable, all the LED light blinking including the power LED light. I try to find the firmware in the website, but here only have the version 1.0.
View 9 Replies
View Related
Nov 8, 2012
I have a Linksys E2500 and recently the power led light on the back of the router started blinking. The router itself seems to be working fine. I can access the router and the router seems to be assigning the IP addresses fine. I did look up the issue on the knowledge base and tried all the solutions but the light is still blinking. Not sure what to do anymore.
View 5 Replies
View Related
Jan 28, 2011
I have had a Dlink dir 615 for some time now and always had a few issues, but nothing a reboot of the router couldn't solve. This time the problem is persisting, though. The wireless signal keeps blinking and on my laptop it says No internet connection. I've rebooted the router, restored the router, rebooted the modem, and nothing seems to work.
View 1 Replies
View Related
Jan 21, 2011
I recently switched from a DSL ISP (Earthlink, Zyxel modem configured as a bridge, pppoE connect) to a cable ISP (Comcast, Arris cable modem, dhcp connect). Basically PC --> DIR615-->Cable modem-->Internets. With the old DSL the Internet activity LED (green, looks triangular) on the DIR615 blinked only when internet activity occurred. With the new Comcast connection it blinks non-stop about 5 times a second! Even if the PC is turned off it blinks. It stops blinking if I disconnect the ethernet cable between router and modem. The connection itself is fine, but if the DIR615 is doing something it should not be doing it might slow the connection down a bit, (or burn something out prematurely?)FYI, the Arris cable modem does not seem to be a router. It takes a cable connection from outside and provides a single ethernet cable and 2 (voice) telephone cables to the house.
View 1 Replies
View Related
Oct 19, 2011
So I just noticed on my Cable modem the link light is blinking orange, per Motorola if its blinking orange - Computer is connected via a 10 mbps or 100 mbps Ethernet port.
On the Linksys E4200 status page it says
Internet Port Speed:
Internet 10/100 mbps
Local Port Speed Port 1 - 1Gbps
Maybe I just noticed this with this router, but I'm pretty sure this didn't start happening until I updated to 1.0.03.
Previously the link light was blue indicating a 1Gbps connection.
View 4 Replies
View Related
May 10, 2013
Region : India
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : S/N: 12B79605315
ISP : BSNL Data One
I had Purchased a brand new TP-Link WifI Modem Router TD-W8961ND with S/N : 12CB5200872 from [URL] and it got delivered few days back. When I am trying to connect it to the internet the modem is not getting connected nor configured. The Power button light, ADSL Light and internet light are continuously blinking and nothing is getting steady. The modem is appearing to be a damaged piece of modem and it is very unfortunate that we have got a modem from flipkart in an unserviceable condition. It came with a warranty of 03 years and I wanted a replacement so that I can use the modem for connecting internet.
View 1 Replies
View Related
Jul 11, 2012
I came home after a few days vacation to find all the lights blinking on my router. I have tried unplugging and rebooting. Same result. I then bypassed the router and have internet on my main computer so I know it is a router issue. I use the router for my laptop and cell phone. Do I need to figure out how to do a master reset or is the router toast?
View 1 Replies
View Related
Jan 20, 2011
I've setted the unit in BRIDGE MODE, and attached on it 3 LAN devices, 1 PC Desktop, 1 NAS WDBE and 1 HP printer ... OK all config process was right and all my units talk togheter via AP Netgear DNG2000, and so i can use for instance the printer with my laptop too connected in WI-FI N. Now usually, In the night I turn off all my devices (DAP included), and when in the morning I need only the printer used by my laptop, obviously I turn on ROUTER - BRIDGE - PRINTER - LAPTOP but NOT the DESKTOP ... and so the DAP can't reconnect automatically to the router (both the lights AP/BRIDGE are on and fixed) ... I turn on the PC and the BRIDGE reconnect to the world .... BUT I DON'T WANT turn on everytime the desktop !
1) all gears has fixed IPs
2) DHCP server deactivated on the AP main router (DNG2000)
3) no WPS used, only WPA2-PSK (AES) personal keys on all gears
once that DAP-1522 is connected to the router .... all work fine (also when I turn off the DESKTOP).so the workaround is never turn-off the DAP ? I can't believe ... and who will save the energy planet
View 2 Replies
View Related
Apr 15, 2011
1 =if its a rev 1c on the sticker that makes it DIR-615_REVC I am assuming
2= suddenly it shut down today yellow power lite , i cycled and nothing i reset then got a request to do a firmware update! I shut it down for a hour cycled and after a few minutes green power lite all my settings were still in place?I would think a reset would wipe this out.Its only 2 years old and would be surprised if its dieing.
View 2 Replies
View Related
Mar 24, 2013
I have a DIR-615 H/W ver C1.Suddenly everything stopped working. The D-Link light is green and the power light is amber, no other light is up (LAN or Internet).I've try to do a reset, no effect.Can't connect to the router even with a LAN cable (LAN lights stays dead with a working cable and computer plug-in).
View 3 Replies
View Related
Dec 23, 2012
I have a DIR-615 v e3 router
Did a bad dd-wrt flash and now all it does:
-no power light
-solid green lights: WAN-L1-L2-L3-L4
tried to go to recovery mode (power on while holding reset switch).....does not work.my search on the internet revealed, that after bad flash, power light still comes on, maybe as orange, maybe blinking, or just blinks once
View 1 Replies
View Related
Mar 11, 2012
I reseted my router because I couldn't go in the login so now eveything is green except the earth looking thing next.the power it is orange Cause I really need my internet
View 1 Replies
View Related
Dec 18, 2011
My Dir-615 stopped working some weeks ago and I switched to another router until I had time to look at it. Tonight I checked the ps voltage and it read exactly +5v but just for a test I tried another 5v ps (which tested a little higher) and it worked. The ps that works reads about link +7vdc. Before this the power light came on with the occasional blink but I could't connect.
View 5 Replies
View Related
Jun 11, 2011
The modem is sure working and so as the Ethernet cable since I am using it with another computer. I already had the driver updated but still it's not working. I actually suddenly heard noise in my computer before this happened. OS Windows 7.
View 7 Replies
View Related
Jun 14, 2012
HandPunch 3000 Time & Access Device, no Communication over the Ethernet, on the Ethernet Card the red light flashes for 1sec then red & Green for 1sec.
View 1 Replies
View Related
Oct 26, 2012
The send light is steadily blinking. Yesterday I disconnected the cable into my main cable box connected to my tv, so I could move it into a new tv stand I bought, and ever since then I get no Internet connection (tv cable works fine.) I cant see how that made my Internet go out, but maybe it did. I checked connections on both ends and all cables are tightly secured.Here is a log of my modem, I found out how to get it through this site.[CODE]
View 5 Replies
View Related
Jan 24, 2011
black screen with small line in left corner blinking
View 1 Replies
View Related
Mar 27, 2013
My Cisco WAG32ON internet light in blinking red
View 1 Replies
View Related
Sep 18, 2011
my DSL light is blinking at evening around 6:30 evening every day.
View 1 Replies
View Related
Apr 30, 2011
the router is functional, however the green light has never blinked like it is now.
View 1 Replies
View Related
Feb 21, 2012
Network port: Yellow light blinking and orange light not showing
View 1 Replies
View Related
