1 =if its a rev 1c on the sticker that makes it DIR-615_REVC I am assuming
2= suddenly it shut down today yellow power lite , i cycled and nothing i reset then got a request to do a firmware update! I shut it down for a hour cycled and after a few minutes green power lite all my settings were still in place?I would think a reset would wipe this out.Its only 2 years old and would be surprised if its dieing.
I recently (Jan 2011) bought a new DLink DIR-600 Router for my home use. It was working excellent for last two months and suddenly last Monday all hell broke loose. I have a WiMax connect and have a POE box. I plugged in the cable from POE box into my router and it used to work fine. But now, the globe indicator on the router box is not turning green. It remains yellow. When I remove the POE cable from router and plug it directly to my laptop, it works fine.
View 2 Replies View RelatedMy internet light flashes at times yellow.Some times i lose internet connection .I have never had this problem with my linksys router.
View 3 Replies View RelatedHave noticed this in almost a regular pattern. About every 3 seconds the internet light whick is blue most of the time will ocassionally flash white then maybe yellow. Does not appear to interupt internet access yet last only a second (at the longest),so don't know if I would notice. Am connected to DSL modem and see no change it its indicator lights,(traffic, collision, lan), when it occurs on the DIR-655. Have three PC's and a network (LAN) printer as well as wireless enabled. BTW is does not matter if wireless is active. What do the different colors mean ?? Blue = Connected White = Yellow =
View 3 Replies View RelatedI have a DIR-615 H/W ver C1.Suddenly everything stopped working. The D-Link light is green and the power light is amber, no other light is up (LAN or Internet).I've try to do a reset, no effect.Can't connect to the router even with a LAN cable (LAN lights stays dead with a working cable and computer plug-in).
View 3 Replies View RelatedI have a DIR-615 v e3 router
Did a bad dd-wrt flash and now all it does:
-no power light
-solid green lights: WAN-L1-L2-L3-L4
tried to go to recovery mode (power on while holding reset switch).....does not work.my search on the internet revealed, that after bad flash, power light still comes on, maybe as orange, maybe blinking, or just blinks once
I successfully linked a DIR-655 (A4, FW:1.21) via WPS.
I then updated the DAP-1522 to FW:1.21 from 1.1.
Things looked great. I then moved it upstairs to my home theater.
Plugged it in and got a blinking power light. Completely unresponsive to either linkage or 192.168.0.50.
I have followed everyone advice listed either here or in Amazons reviews. And from my own experience with similar electronics the flashing power LED is indicative of a "brick".
I have initiated a replacement shipment from amazon. Just wanted to see if anyone had seen this before.
I reseted my router because I couldn't go in the login so now eveything is green except the earth looking thing next.the power it is orange Cause I really need my internet
View 1 Replies View RelatedMy Dir-615 stopped working some weeks ago and I switched to another router until I had time to look at it. Tonight I checked the ps voltage and it read exactly +5v but just for a test I tried another 5v ps (which tested a little higher) and it worked. The ps that works reads about link +7vdc. Before this the power light came on with the occasional blink but I could't connect.
View 5 Replies View Relatedim wondering if it still have issue on shareport. cause last time i updated my 655 to 2.07 it has issue with the shareport.
View 1 Replies View RelatedI have Cisco 3560 switch in my network . from there we are distributing connection to our broadband customer in difference area. one location side port are getting glow yellow after every interval which result network goes down. when i replug the port its getting OK.
View 1 Replies View RelatedDoes a ASA5505 have a limited lifetime warranty? I have a ASA that is not covered on a SmartNet contract, as far as I know of, it is not owned by my company. It has a yellow status light, and will not boot. Will cisco replace it?
View 1 Replies View RelatedI have a router with the specs in the subject area. I have a weird problem with my DIR-655 router when saving "daylight savings time." Now, the time is correctly set and one week later, the time reverts back to non-daylight savings time.I am currently syncing my router's time with an ntp server (Cornell in NY). Is this a known bug? I definitely don't want to update my firmware as I like its performance. This is the only issue I want fixed.
View 1 Replies View RelatedNetwork port: Yellow light blinking and orange light not showing
View 1 Replies View RelatedSo, I messed around with my router a little too much and just want to restore it back to the original firmware now. I have a WRT54GS v7 Linksys router and tried to follow this guide to flash the firmware to something a little more useful. After step 7 of that guide, I can't ping my router, can't access the GUI, and have no idea what my router's IP is. If I assign each computer plugged into the router an IP like 192.168.1.2 I can ping them, so the router is still functioning somewhat. I'm plugged into my modem right now to get on the Internet.
Right now, my power light is off, my DMZ light is off, my WLAN light is off, but the other lights turn on if I plug a cord into its port (plug a computer into port 1, port 1's light comes on). When I do an ipconfig /all i get this. I doubt the web interface still works, but if I could at least get the router's IP, couldn't I use tftp and put the firmware on that way?
My WAG120N power light is always red whenever plugged in. I can't access the configuration page. My adapter works fine and the Reset button doesn't work. I can't find any troubleshoot for the "red power light" problem in user manual !
View 3 Replies View Relatedmy LAN card is not responding but it only receives light from the power source?how can i make it work?
View 1 Replies View RelatedIve recently tried to update the firmware and everything went as instructed, then the power and LAN light went out. Now I have the indicator lights for the computer and modem, but thats is. No internet or SSID broadcast. I cannot log into or ping the unit, and have tried the hard reset many times, with no effect.
View 8 Replies View RelatedI have a Thomson TG784 router and i have a problem with it. once i turn on my rouet, and no cables are plugged in, except the power one, the two lights start blinking. The Power and the Ethernet ligh blinking. Once i connect my Ethernet cable and my DSL cable, the light are still blinking with no changes... What should i do?
View 1 Replies View Relatedthe power light on my wrt54g v2.2 router keeps blinking and it wont connect to the internet when connected
View 3 Replies View RelatedMy Linksys X2000 still working but only red power light on (at nomal there are 3 white light on).
View 3 Replies View RelatedMy Wireless-G WRT54G router has a blinking power light and the startup software says "Unable to connect to the Router! Check that the Router has been connected to the computer, and that your Ethernet adapter is working." I tried uploading the firmware but I can't get to the router page to update. Is there a known problem or solution here or am I just going to have to find the router page?
View 9 Replies View RelatedSo I recently upgraded from a WRT54GS to a WRT160N v2, all was well and good for about 3 days. Then I would lose my internet connection every 5 minutes or so, it would fix itself by the time I could open up command prompt and start pinging to pin point the problem. I decided I would update the firmware to see if that would fix the issue. Since doing that the power light has been blinking non stop. I've tried restoring it to factory defaults by holding the reset button for 30seconds, turning it off for 2 minutes and back on. That little blue light just keeps flashing. I can't even access the router setting page using 192.168.1.1. My OS is Windows xp x64 sp2, and I have DSL.
View 9 Replies View RelatedMy router was working fine until today. I figured it out when I tried to get on the internet and it wouldn't let me. I hooked up the ethernet directly from my modem to my computer and then my internet worked fine.
View 4 Replies View RelatedI need fixing my router. I updated the firmware and it said the upload has failed ever since then:
-the router doesn't work
-blinking power light
-DMZ light doesn't turn on
-can't access 192.168.1.1
My router is a WRT54G v5
We have a Cisco SRP 527W router that was not showing up on the LAN. so we tried a Factory Default reset but it seems to be dead.
The power light is flashing constantly,the 4 LAN light are constantly on,the DSL Data light comes on for 1 sec when device is powered up.
i have tried connecting directly to a PC, the NIC reports as network cable unplugged.i have tried the (power on device, hold down reset button, power of after 30 sec, power on after 5 sec, release reset button after 5 sec) but still "network cable unplugged".
the firmware flash utility will not find the NIC the device is connected to.the router is less than a year old, is there a fix or is it a warranty replacement ?
the power light on my wrt54g v2.2 router keeps blinking and it wont connect to the internet when connected, what should i do?
View 1 Replies View RelatedNo download available and none available via Linksys Live Chat or FTP and having spent the best part of the week trying to find relevant firmware on other forums I decided to come here to get answers to the following questions, hopefully from version 1.0 experienced owners or not.
#1. Can the firmware of version 2.0 and 3.0 be reduced to flash version 1.0?
#2. When diagnosing the blinking power light issue by connecting directly to the router and the network card using "ping -t 192.168.1.xxx" which network address do I use, 192.168.1.1 or 192.168.1.2 to 2xx?
I get a reply using 192.168.1.1 but I'm not sure that works when using the TFTP Utility if it's the wrong address on my Laptop to ping?
I have WRT 120 N which has apparently stopped working. When I turn it on, only the power led turns on without blinking, no other light flashes. My computer can't detect the router signals since the signal light is off. Neither does my modem show that the router is connected to it through the ethernet cable. My ethernet cable is working fine, since it is working directly with the computer.
View 6 Replies View RelatedI have a Linksys WRT54GS vers 7.2 Router on an iMac OS X Leopard. The other day I was in the middle of downloading an upgrade for the router when Firefox gave me this message: "Firefox can't find the server". I was no longer able to access the internet, and the router's green power light was left flashing. It flashed for over 24 hours. I tried unplugging the router and shutting down the computer, then plugging in the router and turning on the computer. (I don't have a modem.) The light was still flashing. I tried pressing the logo button for 5 seconds. Still flashing. Tried pressing the reset button in the back. Still flashing. 'I can't get on the internet or into the router. Linksys live chat gave me a link to "Upgrading the router’s firmware using the TFTP utility", which involves a download, but I can't download anything because I can't access the internet.
View 8 Replies View RelatedI've seen related to flashing power lights on the router involve fixes via firmware upgrades off a PC.I'm on an iMac os 10.6.7. The WRT54 used to work as a wireless modem a couple of years ago. Tonight, it doesn't. power light blinks. Can't access any webpage interface for the thing. Reset, power down, computer restart, cable modem turn off don't change anything. Is there anything that can be done other than tossing the linksys? If that is the only option, are there wireless routers more suitable for a Mac?
View 4 Replies View Relatedi have Linksys WRT610N V2 now i got problem the power light flashing still keep cannot use but wifi and wan and lan no light but 1 light power only still keep power flashing blinking no stable now i using adsl modem direct connected i using linksys am300 adsl modem
View 1 Replies View RelatedIf I conact from the modem to the pc I have internet so it must be the router. The power light is blinking along with all the port lights. Power light is blinking one time slow 2 fast. Have tried holding the reset button for 30 seconds and unpluging for 30 seconds. Can not go to the ip address it times out. New firmware is not avalible.
View 9 Replies View Related
