Cisco Firewall :: ASA 5505 Yellow Status Light

Nov 27, 2011

Does a ASA5505 have a limited lifetime warranty?  I have a ASA that is not covered on a SmartNet contract, as far as I know of, it is not owned by my company.  It has a yellow status light, and will not boot.  Will cisco replace it?

View 1 Replies


ADVERTISEMENT

Cisco Firewall :: Solid Amber Status Light On ASA 5505?

Apr 14, 2010

I have a Problem with a ASA 5505 when i power on the ASA  the Power LED change to green and the Status light to solid amber. There is no Console output or anything else.

View 9 Replies View Related

Cisco Firewall :: Solid Amber Status Light On ASA 5505 Under SmartNet

Oct 14, 2011

I have an ASA 5505 with status light solid amber color. It is under SmartNet.I'd like to know Cisco will replaced this device with new ASA5505 or upgrade one?

View 2 Replies View Related

D-Link DIR-600 :: Globe Light Is Yellow

Mar 21, 2011

I recently (Jan 2011) bought a new DLink DIR-600 Router for my home use. It was working excellent for last two months and suddenly last Monday all hell broke loose. I have a WiMax connect and have a POE box. I plugged in the cable from POE box into my router and it used to work fine. But now, the globe indicator on the router box is not turning green. It remains yellow. When I remove the POE cable from router and plug it directly to my laptop, it works fine.

View 2 Replies View Related

Cisco :: L3 Ssitchport Light Glow Yellow?

Oct 11, 2012

I have Cisco 3560 switch in my network . from there we are distributing connection to our broadband customer in difference area. one location side port are getting glow yellow after every interval which result network goes down. when i replug the port its getting OK.

View 1 Replies View Related

Cisco Wireless :: 1131AG LWAP Status Led Yellow And Other Blinking Green?

Apr 10, 2013

I have a problem with three AIR-LAP1131AG-E-K9  that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).The SSID broadcast is enabled.On the switch the interface is up and there is traffic going in and out of the LAP.I tired power reset and factory reset for the APs but the problem remains the same.

View 2 Replies View Related

D-Link DIR-615 :: Revision Id / Yellow Power Light

Apr 15, 2011

1 =if its a rev 1c  on the sticker that makes it DIR-615_REVC  I am assuming

2= suddenly it shut down today yellow power lite , i cycled and nothing i reset then got a request to do a firmware update! I shut it down for a hour cycled and after a few minutes green power lite all my settings were still in place?I would think a reset would wipe this out.Its only 2 years old and would be surprised if its dieing.

View 2 Replies View Related

D-Link DIR-655 :: Internet Blue Light Flashes Yellow

Apr 3, 2011

My internet light flashes at times yellow.Some times i lose internet connection .I have never had this problem with my linksys router.

View 3 Replies View Related

Cisco Firewall :: Way To Check Hardware Status Of ASA 5505?

Nov 22, 2012

Is there a way to check the hardware status of an ASA 5505 ? I am thinking of a command or a script to execute.

View 3 Replies View Related

Network Port - Yellow Light Blinking And Orange Not Showing

Feb 21, 2012

Network port: Yellow light blinking and orange light not showing

View 1 Replies View Related

D-Link DIR-655 :: Internet Light Flashes White Or / And Yellow Intermittently

Apr 11, 2011

Have noticed this in almost a regular pattern. About every 3 seconds the internet light whick is blue most of the time will ocassionally flash white then maybe yellow. Does not appear to interupt internet access yet last only a second (at the longest),so don't know if I would notice. Am connected to DSL modem and see no change it its indicator lights,(traffic, collision, lan), when it occurs on the DIR-655. Have three PC's and a network (LAN)  printer as well as wireless enabled. BTW is does not matter if wireless is active. What do the different colors mean ??   Blue = Connected  White =   Yellow =   

View 3 Replies View Related

D-Link DIR-655 :: Internet Status Light Blinks Very Rapidly

May 11, 2013

I have an older rev a DIR-655 that has served me well. Today I finally upgraded my ISP to cable (from a slower DLS connection) to get reasonable speed/price All is working very well but unlike my old DSL modem the internet status light on the DIR-655 blinks very rapidly all the time instead of when traffic is passed.The new modem is a Motorola SB6141,I am running the latest firmware 1.35NA I went through a complete re-setup to see if that would calm the light but no dice there. (the settings arrived at were basically the same for the old Sprint modem) ,Is there something I am missing or is it time to retire the old DIR-655 for something more current.

View 5 Replies View Related

Cisco Wireless :: 1130 Showing Status Light Flashing Orange

May 7, 2012

I have a question, I have an ap (cisco 1130)  that began to get the status light flashing orange and light Ethernet and radio are off.I did a factory reset and it was ok ... past 3 days the problem has happened again.I changed the ap with a new but the situation remained.I tested the wiring and everything is ok.the switch port is set up correctly.

View 11 Replies View Related

Cisco Wireless :: 1524SB - Have Root AP Whose Status Light Showing Solid Red

Jun 30, 2011

We have a root AP whose status light is showing solid red.  We power cycled it and it still shows solid red.  According to the Cisco documentation, this indicates a firmware failure.  Unfortunately, we did not get Smartnet with this access points and instead opted for the limited lifetime warranty.
 
My question is: is there any way to fix the firmware via console?  Whether it be through xmodem or what not.  I ran debugs on the controller and can confirm that the AP is not communcating with the controller.
 
It is also weird that the mesh APs that were previously connected to this root AP show a solid red on their status lights and green for their RF LEDs.  Shouldn't the status LED be flashing green-amber-red?

View 1 Replies View Related

Linksys Wireless Router :: Status Light On EA6500 Won't Stop Blinking

May 9, 2013

I cannot get access into my router because it doesn't seem to have a gateway IP address, although it is assigning my computer an IP address.  

View 1 Replies View Related

Cisco Firewall :: 5520 ASA To Monitor The Ha Status

Apr 15, 2012

We have a Cisco ASA 5520 in HA (Active - Standby). We monitor the CPU,Memory Utilization and Active Session via SNMP polling.And SNMP trap for linkup ,linkdown and Cold start.Our requirement is to monitor the HA status and whenever there is a change in the HA - Failover we have to get a snmp trap.What are the configuration need to be done on the cisco asa.

View 3 Replies View Related

Linksys Wireless Router :: Internet Light On E3000 Doesn't Light Up?

Jul 22, 2011

 I previously asked if I should be concerned that the Internet light on my Linksys E3000 router doesn't light up when I have Internet access. Well recently I had to do a reset and I noticed that during the reset it does in fact light up, but it doesn't come on when the router is done with the reset!

View 1 Replies View Related

Cisco Firewall :: Can't Access PIX 535 Console (in Failover Standby Status)

Jun 14, 2011

we have two pix535 one is ur other is FO license.
 
once a time i found can't access FO pix535 console, i'm sure console cable is ok. when i unplug failover serial cable from FO pix535, i can access pix 535 console.

View 3 Replies View Related

Cisco WAN :: Light Up Every Port Light On 3750g?

Mar 2, 2011

I am trying to light up every port light on a 3750g.  There is not anything plugged into them and I would like to know (just for fun) is there a way to make every port light 1 - 48 turn on using a command?

View 3 Replies View Related

Cisco Routers :: RVS4000 - Switch Status Of IPS Function / Firewall Rules Don't Work

May 3, 2012

I have problem with RVS4000 fw 1.3.3.5. When you switch the status of IPS function (turn on or turn off), firewall rules don´t work from that moment until you restart the router!

View 2 Replies View Related

Cisco Firewall :: Monitoring ASA 5505 Firewall Active / Standby Pair Using SNMP?

Sep 7, 2011

How I can actively monitor the interfaces and overall status of 2 x ASA 5500s in an Active/Standby configuration?
 
I can setup monitoring of the interfaces on the Active member but I'm not sure how to manage the Standby member?

View 1 Replies View Related

Cisco Firewall :: IOS Firewall Versus ASA (5505 / 5510) For Smaller Clients (less Than 50)?

Apr 24, 2012

We were having a discussion of ios firewall vs. asa for smaller clients(less than 50). On using ios firewall(zbf or cbac)and an asa 5505/5510.  One of the arguments brought up on using ios firewall on the router is that a router will do an ip sla failover.  I have configured a number of isr's for this and i know it works good. 

View 1 Replies View Related

Cisco Firewall :: Failover ASA 5505 - Setup Second Inside Interface On Firewall?

Feb 19, 2012

I have a Cisco ASA 5505 in our office. We are currently using Interface 0 for outside and 1 for inside. We only have 1 Vlan in our environment. We have two three switches behind the firewall. Today the uplink to Interface 1, to the firewall, on the switch went bad. I want to setup a second inside interface on the firewall and configure it as failover incase this happens again. I want to attach it to the other switch. Can I do this? If so, what do I need to do? would it only be a passive/standby interface?

View 1 Replies View Related

Cisco Firewall :: Setting Up ASA 5505 To Be Used As Firewall Between BT Internet And 3560 LAN Switch?

Aug 23, 2011

setting up an ASA 5505 to be used as a firewall between a BT internet router(BTNet service) and a Cisco 3560 Lan switch. BT have presented me with a cisco 3800 series router with the following details:

Network Address   Network Mask  BTnet NTE Router LAN Address
      
There are 2 Gigethernet ports on the back of the router port Ge0/0 is connected to the BT NTE and the status light is flashing green. Int ge0/1 is connected into port int e0/1 of the ASA but i am unable to get any connection.

View 21 Replies View Related

Cisco Firewall :: Upgrade From 5505 To 5520 On Network - ASA Firewall Throughput

Feb 27, 2013

I'd like to see some REAL LIFE comparisons of ASA firewall throughput (a bit like this one for ISR G2 Routers - [URL].
 
The reason I ask is that I recently upgraded a firewall from an ASA5505 to an ASA5520 on a small network where the only outside connectivity was a single 10meg Internet circuit with an IPSEC VPN (not landed on the firewall but on a router) to another site.
 
When I swapped out the firewall the users noticed a big improvement. The firewall is not doing anything out of the ordinary - no IPS or VPN, just standard state full inspection.

View 5 Replies View Related

Cisco Firewall :: 5505 - Setting Transparent Firewall Ip Address?

Dec 22, 2011

Trying to set up a asa 5505 in transparent firewall mode. I cannot set the management ip address:
 
ciscoasa> enable
Password:
ciscoasa# config term

[Code].....

View 7 Replies View Related

Cisco Firewall :: ASA 5505 Creating Interface Vlan In Firewall

May 3, 2011

I have been working with ASA 5510,20,40,80 but not with 5505 this vlan and its interfaces are quite confusing.Just want to know how it works and its connectivity to Cisco Switch.Do i have to put the interface of the switch in the same vlan as i am creating the interface vlan in firewall ?Now the switch port connecting to this Eth1 interface should also be in the same vlan ? i.e vlan3 ?? or it will be in trunk ? The default configuration shows the eth0 with no access vlan and interface eth1 with access vlan 2... does it mean the eth0 is in vlan1 ? (Nativ Vlan ) ???

View 4 Replies View Related

Cisco Firewall :: ASA 5505 Firewall To Filter HTTPS Websites?

May 28, 2012

I have a cisco asa 5505 firewall. Is it possible to block secure websites in it like [URL]? I have already tried regular expression filtering but it filters only http traffic.

View 4 Replies View Related

Cisco Firewall :: ASA 5505 - Can't Reach FTP Site While Inside Firewall?

Feb 26, 2011

I am trying to configure our ASA 5505 so that our users can access our ftp site using [URL] while inside the firewall. Our ftp site is setup so that you can reach it by either browsing to the above url or by browsing to ftp://99.23.119.78 but we are unable to access our ftp site from either route while inside the firewall. We can access our ftp site using the internal ip address of 192.168.1.3.
 
Here is our current confguration:
 
Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasaenable password qVQaNBP31RadYDLM encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0 !interface Vlan2nameif ATTsecurity-level 0pppoe client vpdn group ATTip address pppoe setroute !interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!ftp mode passiveobject-group service DM_INLINE_TCP_1 tcpport-object eq ftpport-object eq ftp-dataport-object eq wwwaccess-list ATT_access_in extended permit tcp any host 99.23.119.78 object-group DM_INLINE_TCP_1 access-list ATT_access_in extended permit tcp any interface ATT eq ftp access-list ATT_access_in extended permit tcp any interface ATT eq ftp-data access-list ATT_access_in extended permit tcp any interface ATT eq www access-list 100 extended permit tcp any interface ATT eq ftp

[code]....

View 6 Replies View Related

Cisco Firewall :: 5505 PAT With Single Public IP And Several Servers Behind Firewall

Nov 21, 2012

New to the ASA 5505 8.4 software version, but here is what I'm trying to do:
 
-Single static public IP:  16.2.3.4
-Need to PAT several ports to three separate servers behind firewall
-One server houses email, pptp server, ftp server and web services: 10.1.20.91
-One server houses drac management (port 445): 10.1.20.92
-One server is the IP phone server using a range of ports: 10.1.20.156
 
Basically, need to PAT the ports associated with each server to the respective servers behind the ASA 5505.  Is anything missing from this config? Do I need to include a global policy for PPTP and SMTP? [code]

View 11 Replies View Related

Cisco Firewall :: ASA 5505 Transparent Firewall With Web Sense Integration

Apr 27, 2011

I'm integrating a Cisco ASA5505 with a Websense proxy. I have a configuration setup where we have four routers which are used for Internet access. There are two VLAN's - Guest and Private. What I would like to achieve is making the use of available bandwidth by load distribution via GLBP, and filtering users web traffic. Two routers will be used for a GLBP group in one VLAN, and the other two routers will be used for GLBP in another VLAN.The users are connected to a Cisco 2960 switch and are in their respective VLAN's. I'm planning a 802.1q trunk to a Cisco ASA from the 2960 switch, carrying both VLAN's.What I would like to know is if there is a CSC module (or similar) which has Websense installed on it, and if it is possible to setup the ASA5505 in transparent mode to filter the traffic in this way? Hopefully this would allow multiple users to take advantage of the additional bandwidth, and not be restricted by using a traditional proxy setup which where all web traffic would be originating from a single MAC address.

View 1 Replies View Related

Cisco Firewall :: 5505 ASA Trunk Port In Firewall

Apr 30, 2012

I have an issue with my firewall,each time i configured a trunk port in the firewall and connect a sw 2960S with a trunk port also, all the interfaces in the Firewall go down ( virutal intertaces, inside, outside , dmz) , also another switch 3750 that is connected to another port in the firewall( access port only) it start to a new negotiation of spanning tree.What could be causing this problem? the firewall didnt sedn bdpdu i think the IOS of the firewall its a 8.2

View 3 Replies View Related

Cisco Firewall :: 5505 Firewall Between HQ And Remote Site

Jun 12, 2012

we are planning on connecting a new aquired company to ours soon?We will connect the remote site to the HQ via a D3. I've been told we will need to have a firewall between them and us for a time. I was thinking of terminating the D3 connection at the remote site of 80 users. Can I use the asr as a firewall as well, to protect the HQ from the Remote site - or should I use a seperate appliance?I was thinking of a asa5505 but, am concerned with bandwidth limitations of the box?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved