Cisco Wireless :: 1131AG LWAP Status Led Yellow And Other Blinking Green?
Apr 10, 2013
I have a problem with three AIR-LAP1131AG-E-K9 that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).The SSID broadcast is enabled.On the switch the interface is up and there is traffic going in and out of the LAP.I tired power reset and factory reset for the APs but the problem remains the same.
View 2 Replies
ADVERTISEMENT
Feb 16, 2010
I have a Cisco 2106 WLC, and a 1131ag Access Point. The 802.11a/g Radio "Operational Status" = DOWN. All other Radios are UP. I'm wondering if this is normal behavior as no clients are connecting to it over the 802.11a/g Radio.
View 8 Replies
View Related
Feb 15, 2012
I'm having a strange issue with an 1142 AP. I have a 5508 WLC at my corporate HQ and have AP's in many locations, connected by MPLS WAN. I have one site where the 1142 is blinking green and doesn't associate with the WLC. I have tried a different switch port with the AP (didn't work) and I know that the switch port is good because I have a 1252 that works just fine at this remote location.The really weird part is that the AP is blinking green, but the switch port shows that it is not connected and the green port light on the 3560 switch is not lit. I have verified wiring in the closet, but unfortunately the 1142 AP is hanging 40ft high in a shop and I don't have access to it.Is it possible that there's a bad rj-45 termination that is allowing PoE to the AP, but no data?
View 14 Replies
View Related
May 28, 2013
I'm installing the first out of 10 Aironet AP's with an inline injector. The lights on the Aironet and alernating blue, green, red. I know the error code is for DHCP, but when I plug it in I see the AP on my DHCP server and it does pull an IP address. I can ping the ip address, but I cannot access it through my browser.
I have tried deleting the entry out of the DHCP and power it back on again. I have also tried another unit with the same results. I don't have a RJ-45 to serial cable.
View 10 Replies
View Related
May 20, 2013
3602I constantly shows a fast blinking green light, watching the boot up I see the following:
Loading "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA"...uncompress: Unknown mzip segment type: 2
Error loading "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA"
View 7 Replies
View Related
Mar 17, 2011
The DCS-930L setup information refers to a steady green LED, but mine is irregularly blinking. Is this the normal, indicating connection working?
View 3 Replies
View Related
Apr 30, 2011
the router is functional, however the green light has never blinked like it is now.
View 1 Replies
View Related
Jul 11, 2011
I am replacing an old Catalyst 3550 (that has 2 Gig ports) with a 3750 (that has 4)- I used the exact same configuration in the new switch. When I plugged in the new 3750, the trunk ports started blinking from green to amber. I dont know why this is occuring- it SEEMS to be fine, but we havent thrown a whole bunch of traffic over it.
View 4 Replies
View Related
May 9, 2013
I cannot get access into my router because it doesn't seem to have a gateway IP address, although it is assigning my computer an IP address.
View 1 Replies
View Related
Feb 21, 2012
Network port: Yellow light blinking and orange light not showing
View 1 Replies
View Related
Nov 27, 2011
Does a ASA5505 have a limited lifetime warranty? I have a ASA that is not covered on a SmartNet contract, as far as I know of, it is not owned by my company. It has a yellow status light, and will not boot. Will cisco replace it?
View 1 Replies
View Related
Dec 16, 2012
I have a 1 month old SG200-26P - the green status LED is blinking constantly (> 30 minutes), I cannot access the webGUI, nor is it responding to ping. I have tried resetting via holding reset for > 10 seconds with no effect, the status/activity LEDs are still illuminating against all connected ports, excluding any of the PoE ports which are running a couple of cisco IP phones. I've tried accessing the device via both the static IP I configured, and the default IP.
I have disconnected all ports, then powered on the device, but same results...Do I have a dead switch? Anything I can do other than return for warranty claim which is going to be last resort due holiday period and leaving the customer offline for extended period...
View 9 Replies
View Related
Mar 18, 2009
I have a 1 month old SG200-26P - the green status LED is blinking constantly (> 30 minutes), I cannot access the webGUI, nor is it responding to ping. I have tried resetting via holding reset for > 10 seconds with no effect, the status/activity LEDs are still illuminating against all connected ports, excluding any of the PoE ports which are running a couple of cisco IP phones. I've tried accessing the device via both the static IP I configured, and the default IP.
I have disconnected all ports, then powered on the device, but same results...
Do I have a dead switch? Anything I can do other than return for warranty claim which is going to be last resort due holiday period and leaving the customer offline for extended period.
View 10 Replies
View Related
Feb 12, 2013
I can not fix the problem with the router. I power it up, all is GREEN, then it blinks RED, then GREEN, and finally RED. The router is terminally not connected to the Internet. How can I check if the router is BAD. I have done all the troubleshooting, examples:
connected ethernet directly to computer - no problems
attempted to fix problems via belkin software
changed channels on modem
updated firmware
etc, etc
View 1 Replies
View Related
May 20, 2012
We're in the process of upgrading our Wireless AP's from autonomus to LWAP. We're doing the upgrades remotely (we have 100's of sites to do, and it's not possible to be there to console on to each one), using a local computer to upgrade them to LWAP's with the Cisco Upgrade Tool.Having some inconsistent bugs pop up though from time to time.The most common one is that it basically buggers up the IP address after applying the recovery firmware image. It's supposed to keep the IP it had according to the IPFile.txt (for example 172.25.25.4), but it does something very weird... it keeps the last two octets (so 25.4 from the e.g) but replaces the first two octets with a 192.168 address. So the final address in this example after the UpgradeTool has done its work, is 192.168.25.4 - which is compeltely wrong.
This causes it to be unable to talk to the WLC (obviously, with bogus IP information it will struggle), and gives us big problems in that it wont ever come up unless someone can console to the AP and fix it. We can usually resolve the issue by munging about on the switch - switching the port it's connected to between access and trunk and doing some shut/noshut cycles seems to do the trick mostly.
View 9 Replies
View Related
May 15, 2012
i have out of box 20 AP 1100 LWAP...and cisco 22XX WLC......i need few information
1- what is option 43 in DHCP once i take the AP out of box shd i config static IP for managment
2- How LWAP register to WLC?
View 1 Replies
View Related
Dec 5, 2012
I have WLC 2504 with 7.2.103.0 software version , & 2 different LWAP 1262n & 1231G with "c1200-rcvk9w8-mx.124-21a.JA" Image.The 1262n is joined to the to the controller and working fine but the 1231G it can't join the controller , the controller says "Join request received from an unsupported AP" !!i will attaches the logs for this AP.
View 3 Replies
View Related
Aug 18, 2011
I have an AIR-AP1242AG-E-K9 which had c1240-k9w8-mx.124-21a.JA loaded, I followed the link below and upgraded with Cisco’s upgrade tool to c1240-rcvk9w8-mx with no problems at all, after the upgrade I could then see the LWAP on the 4402 controller and had it working a treat.Now the problems begin, I brought it into the office where we have 5508 controllers, plug in the LWAP into our management switch and boot it up I get an IP assigned from the DHCP server and the AP goes into discovery mode but never finds the controller.I have logged the boot process but this does not give much away, our other 1100 series AP’s boot fine,
[URL]
Console Boot Log.
Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
[code]....
And that is where she sits and does nothing more, I have noticed the DNS problems but the other 1100 series LWAP’s boot up after show that same issue.
View 2 Replies
View Related
Jun 20, 2011
Is it possible to Change IOS of 1252 LWAP AP to Autonomous AP? I have seen some documents for changing Autonomous AP to LWAP and change back procedures.
View 4 Replies
View Related
May 7, 2012
I have a 1121 autonomous AP which I switched to the lightweight mode by copying the LWAPP ios to its flash and issuing the command boot system flash IOS_file_Name. After that I was unable to associate the AP to my wireless controller because it was continiously rebooting. Unfortunately this AP does not have a console port so I can access the debug and see what is happening. And I was not able to switch it back to the autonmous mode becaus the AP won't accept the Autonomous mode IOS anymore.
View 2 Replies
View Related
Feb 27, 2012
I can configure two APs as a bridge with one as an AP with RMW enabled, and the other in WGB mode. I have three VLAN, each configured on both APs with their own SSID. Each switch (cisco switches) port is in trucking with only the three vlan allowed. The APs are associating with each other but not passing VLAN traffic.
View 8 Replies
View Related
Jun 9, 2010
On autonomous AP's one can disable the bright status LED using the "led ....." command. But how can I disable the LED on a LAP-1131AG? The AP hangs in a bedroom so the light is quite annoying.
View 3 Replies
View Related
May 31, 2012
My AP 1131AG is not light weight mode and not able to boot. I have captured logs from consle port it stuck up after following error:
Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
[Code].....
View 3 Replies
View Related
Jun 5, 2011
IOS of my LAP 1131AG is corrupted. It is giving error messages while booting and asks for boot image.
View 2 Replies
View Related
Apr 4, 2011
I would like to convert some 1142N LAP to Autonomous. Is there a way to do ?
I have noticed a new image : c1140-k9w7-tar.124-25d.JA.tar
I don't see a way to replace the image in flash ?
View 1 Replies
View Related
Apr 29, 2012
I have an environment of Cisco 5508 Wireless Controller and 1142N Access Points. I have a problem with the ratio of concentration of clients connecting to Access points in floors.
Recently I have been turning off 802.11a on the access points and I am seeing increase in client count in a few of acces points.What is the maximum client count supported by these access points and how do i ensure they are distributed evenly on access points?
View 4 Replies
View Related
Mar 5, 2013
I have a 3502 AP that I am attempting to set back to factory default including clearing the username and password. It is going to work off of 4400 controllers. I have read numerous documents no how to clear the config and password but so far nothing has worked. I can get it into ap: mode but not sure what to enter here. When I do a dir there doesnt seem to be any files. It will pull an IP address via the local router but cannot communicate with WLC.
View 28 Replies
View Related
Mar 5, 2013
I am installing a small wireless network (for the firs time). The WLAN is connected to a router/firewall and consists of a Cisco 2960-C Series 8-Port Compact Ethernet Switch, a Cisco Aironet 2500 Series Wireless LAN Controller for Lightweight Access Points and a Cisco Aironet 1140 Series g/n Lightweight Access Points (five AP if I get it to work).
My problem is that when a client connects to the access point it does not get an IP-address.
In the WLC DHCP proxy is enabled and Internal DHCP server is used.
The scope is from 192.168.104.65 - 192.168.104.99
The WLC IP is 192.168.104.60
The DHCP server is given as 192.168.104.60
When starting the system I can see the the AP have the IP 192.168.104.66 so it seems the DHCP gives out IP-addresses. I can ping the AP.
When a client connects to the APit is asked for the security key and the client can be seen in the WLC monitor section. The client never gets an IP-address; in the WLC monitor 0.0.0.0 is shown.
View 4 Replies
View Related
Mar 11, 2013
I am running big wireless network, with 20no of 5500 with 7.0.116.0 version. I have more than 20,000 AP's. If i add some config in primary controller or do some changes or reboot all the AP's are moving to backup controller. this doesn’t have any problem, but many AP's which moved to backup controller are losing VLAN mapping. This happens every time. Primary --> backup, backup --> primary. Both controllers have same vern...same config etc..
AP model: AIR-LAP1252AG-A-K9
Controler model: AIR-CT5508-K9
View 15 Replies
View Related
Apr 2, 2013
My customer has an 1131AG AP, andhas Problems with joining to the controller. I did a debug and have the following output. The WLC (5508) shows the AP with Primary SW version as 3.0.51.0. this Release does not showup in any compat matrix! It seems to start downloading the software. after a while it stops with the bolded output, twice the same Bytecount!?
*spamApTask0: Apr 03 09:55:59.998: 68:ef:bd:94:e7:9c 5179392 Bytes Transferred to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.097: 68:ef:bd:94:e7:9c Received LWAPP
[Code].....
View 22 Replies
View Related
Feb 14, 2013
I have succeeded in turning the AP from autonomous into LWAPP mode with the Ugrade tool. The AP has been loaded with c1130-rcvk9w8-tar.124-10b.jda due to the upgrade tool version 3.4,After reboot, the AP appears on the vwlc (YES!) however as you can see in APvwlc.jpg the AP now have version 3.0.51.0.I need the AP to be loaded with version 7.3.101.0 with FlexConnect mode.
View 24 Replies
View Related
Jul 27, 2012
I have a dozen clients on an 1131AG and they cannot ping each other. I get a reply but it says destination host unreachable.
View 4 Replies
View Related
Jul 25, 2012
We have six 1131AG WAP's, lightweight, managed through a 2514 controller. We have a Windows 2008R2SP1 domain. Wireless users can connect to the network, and log on to the domain without any apparent 'issues'. They can access domain resources. However, they cannot browse the domain in Network Neighborhood. Interestingly, they can map a drive to shares on the servers, so long as they manually type in the path. This occurs with desktops running Windows 7 Pro, 32 and 64 bit; XP Pro SP1, 32 and 64 bit; ditto for laptops. The wireless NICs vary as to manufacturer, but do include Trendnet, Intel Centrino, and Intel Pro 100/1000. If I connect any of these machines via by wire, they can access all domain resources and browse the domain in Network Neighborhood in the usual manner.
View 3 Replies
View Related
