Cisco Wireless :: 1131AG APs As Bridges?

Feb 27, 2012

I can configure two APs as a bridge with one as an AP with RMW  enabled, and the other in WGB mode. I have three VLAN, each configured on both APs with their own SSID. Each switch (cisco switches) port is in trucking with only the three vlan allowed. The APs are associating with each other but not passing VLAN traffic.

View 8 Replies


ADVERTISEMENT

Cisco Wireless :: Aironet 1260 As Bridges?

Feb 2, 2012

Is it possible to create a wireless site to site link using 1260 access points as bridges (like the 1300 series)?
 
Also if so, can you use 11n channel bonding on the bridge link?
 
I need to link 2 buildings together wirelessly approximately 70 metres apart.  There is direct line of sight between them.

View 10 Replies View Related

Cisco Wireless :: Disable Led On 1131AG While Associated With WLC

Jun 9, 2010

On autonomous AP's one can disable the bright status LED using the "led ....." command. But how can I disable the LED on a LAP-1131AG? The AP hangs in a bedroom so the light is quite annoying.

View 3 Replies View Related

Cisco Wireless :: 1131AG AP Not Able To Boot

May 31, 2012

My AP 1131AG is not light weight mode and not able to boot. I have captured logs from consle port it stuck up after following error:
 
 Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories

[Code].....

View 3 Replies View Related

Cisco Wireless :: IOS Of LAP 1131AG Is Corrupted

Jun 5, 2011

IOS of my LAP 1131AG is corrupted. It is giving error messages while booting and asks for boot image.

View 2 Replies View Related

Cisco Wireless :: 1300 Multiple VLANs Between The Bridges

Feb 20, 2008

I have two Cisco 1300's acting as bridges only.  I have created an infrastructure ssid on VLAN 2 and assigned this to the radio.  I am carrying multiple VLANs between the bridges (using subinterfaces on the fastethernet and radio ports).I have enabled WPA-PSK, but how do I check that this is being used between the bridges? Also - I have a switch connected at each end of the bridge.  When I make VTP changes, the remote switch does not pick these up - is this because VTP goes over VLAN1 regardless of the Native VLAN (2 in my case)? Do I have to carry VLAN1 over the bridge to get VTP working, or is there an alternative solution?

View 7 Replies View Related

Cisco Wireless :: BR1410A-E-K9 Adding Two More Bridges EtherChannel

Jan 13, 2013

Two facilites are connected via wireless bridge(AIR-BR1410A-E-K9).we wanted to add wireless bridge at each facility to increase the bandwidth.So we will have two wireless bridge at each facility connected wirelessly. and we wanted to achieve it by doing some kind of etherchannel in the switches at each location.

View 4 Replies View Related

Cisco Wireless :: 1310 Bridges Keep Losing Connection?

Nov 28, 2010

I have two 1310 bridges...one set as root and the other as non-root.For some reason they keep losing connection.  When I reboot the non-root bridge, link is established.Both bridges have an antenna connected with the right connector and they have the setting antenna transmit right antenna receive right
 
logs from root bridge
Nov 29 13:52:53.311: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:52:53.311: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station XXXX.XXXX.XXXX Reason: Previous authentication no longer validNov 29 13:52:53.568: %DOT11-6-ASSOC: Interface Dot11Radio0, Station Test XXX.XXXX.XXXX Reassociated KEY_MGMT[WPAv2 PSK]Nov 29 13:55:16.260: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:55:16.260: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station XXXX.XXXX.XXXX Reason: Previous authentication no longer validNov 29 13:55:16.550: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the clientNov 29 13:55:16.550: Client XXXX.XXXX.XXXX failed: reached maximum retries
 
logs from non-root Nov 29 2010 13:52:55: %DOT11-4-UPLINK_DOWN: Interface Dot11Radio0, parent lost: Received deauthenticate (2) not validNov 29 2010 13:52:55: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down The signal strength is around -84dBm Cisco IOS Software on both bridges is: C1310 Software (C1310-K9W7-M), Version 12.4(10b)JA1, RELEASE SOFTWARE (fc2)

View 12 Replies View Related

Cisco Wireless :: AIR-BR1410A-E-K9 Adding Two More Bridges / EtherChannel

Dec 3, 2012

Two facilities are connected via wireless bridge(AIR-BR1410A-E-K9).we wanted to add wireless bridge at each facility to increase the bandwidth.So we will have two wireless bridge at each facility connected wirelessly.and we wanted to achieve it by doing some kind of etherchannel in the switches at each location..

View 7 Replies View Related

Cisco Wireless :: 1410 Bridges Link Fail?

Jun 22, 2011

I have a point to point link of 9.27 km using 1410 bridges and AIR-ANT58G28SDA-N antennas as per the documentation that would be an easy to deploy link and it should work at 54 Mbps, eventhough it drops the link, it's so slow and the power measurments indicate -70 dbm (aprox) right under the antenna which is at 9 m height.
 
This is not the first time I have troubles with 1410 bridges, the other two times I had to change them for 1310 bridges. I wonder if it has to do with some configuration tunning like, external antena gain, link distance or anything else? By the wat this is ocurring in México don't know if that might be worth of taking into consideration in order to deploy a 1410 link.

View 3 Replies View Related

Cisco Wireless :: 1131AG Not Joining To Controller (7.4.100)

Apr 2, 2013

My customer has an 1131AG AP, andhas Problems with joining to the controller. I did a debug and have the following output. The WLC (5508) shows the AP with  Primary SW version as 3.0.51.0. this Release does not showup in any compat matrix! It seems to start downloading the software. after a while it stops with the bolded output, twice the same Bytecount!?
 
*spamApTask0: Apr 03 09:55:59.998: 68:ef:bd:94:e7:9c 5179392 Bytes Transferred to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.097: 68:ef:bd:94:e7:9c Received LWAPP

[Code].....

View 22 Replies View Related

Cisco Wireless :: AP 1131AG Cannot Upgrade From Version 3.0 To 7.3

Feb 14, 2013

I have succeeded in turning the AP from autonomous into LWAPP mode with the Ugrade tool. The AP has been loaded with c1130-rcvk9w8-tar.124-10b.jda due to the upgrade tool version 3.4,After reboot, the AP appears on the vwlc (YES!) however as you can see in APvwlc.jpg the AP now have version 3.0.51.0.I need the AP to be loaded with version 7.3.101.0 with FlexConnect mode.

View 24 Replies View Related

Cisco Wireless :: Clients On 1131AG Cannot Talk To Each Other

Jul 27, 2012

I have a dozen clients on an 1131AG and they cannot ping each other.  I get a reply but it says destination host unreachable.

View 4 Replies View Related

Cisco Wireless :: 1131AG Can't Browse Domain

Jul 25, 2012

We have six 1131AG WAP's, lightweight, managed through a 2514 controller.  We have a Windows 2008R2SP1 domain. Wireless users can connect to the network, and log on to the domain without any apparent 'issues'. They can access domain resources. However, they cannot browse the domain in Network Neighborhood. Interestingly, they can map a drive to shares on the servers, so long as they manually type in the path. This occurs with desktops running Windows 7 Pro, 32 and 64 bit; XP Pro SP1, 32 and 64 bit; ditto for laptops. The wireless NICs vary as to manufacturer, but do include Trendnet, Intel Centrino, and Intel Pro 100/1000. If I connect any of these machines via by wire, they can access all domain resources and browse the domain in Network Neighborhood in the usual manner.

View 3 Replies View Related

Cisco Wireless :: Activate WAP4410N And AP-1131AG?

Mar 16, 2011

I have WAP4410N and AP-1131AG for the school lab's Access point. First, WAP4410N doesn't make connection to wired network.
 
There's no DHCP server in our school and uses below :
 
192.168.x.x ip address
255.255.0.0 Subnet
192.168.1.254 Gateway
210.220.16.7 DNS address.
 
So I seted these settings on the configuration page, but when I connect to the WAP4410N wireless, I can't connect to the internet. Problem reporter in Windows 7says there's IP adress problem on the access point. ...but the ip address is correct. I did everything on the manual ....
  
Second, AP-1131AG. I entered with console cable and changed the ip address. And I enabled wireless radio(default:disabled) but I cannot find SSID with wlan. I added SSID on SECURITY-SSID manager. It says 'interface on' on 802.11a/g, but it is the same. I can't find SSID. other labtops can't, too.. tried using vlan. FAILED....

View 5 Replies View Related

Cisco Wireless :: Combining 1310 Bridges With 5508 Controller

Jul 10, 2012

I have 2 campuses.  I have my 5508 wireless controller working beautifully on my main campus using LDAP.  (YAY!!)  Now for my problem.  My remote campus has 1310 bridges.  I was able to successfully upgrade one of them to work with the controller, however, I can't get the other two bridges to talk to the one that I upgraded and I can't get them to upgrade, it indicates that they need to be the root.  I have several small buildings on that remote campus, than need that remote bridging in order to be able to have network access. 

View 7 Replies View Related

Cisco Wireless :: 1300 Series Bridges Load Balancing

Apr 6, 2008

Is it possible to configure two 1300 series bridges at one location, each handling a bridge link to another location to BOTH backup and load balance for each other should one of them fail?

View 5 Replies View Related

Cisco Wireless :: 1131Ag Showing Operating Status Down

Feb 16, 2010

I have a Cisco 2106 WLC, and a 1131ag Access Point.  The 802.11a/g Radio "Operational Status" = DOWN.  All other Radios are UP.  I'm wondering if this is normal behavior as no clients are connecting to it over the 802.11a/g Radio.

View 8 Replies View Related

Cisco Wireless :: 1131AG Series AP Supported By WLC 4400?

Jan 21, 2013

I am planning to buy new AP for my existing setup. we are using 1131AG series AP, we need to go for new one with n supported with external antenna.
 
Current software version on controller is : 7.0.235.3

View 8 Replies View Related

Cisco Wireless :: WLC AIR-WLC2106-K9 With 2 X Aironet 1131ag Not Appearing

Oct 3, 2012

we have the WLC and 2 x Aironet AP's that is powers over PoE. The other day is was reloaded and since then the AP points are Blinking Red, according the the Aironet manaul this means some sort of boot error? They are also not appearing on the WLC from the GUI or CLI running a show ap summary. Interesting though I can see them via CDP, however they are not picking up IP's as they are listed as 0.0.0.0. After checking with colleagues I was told these were set statically.
 
Is it possible that the points not having IP addresses is a sign of a corrupt boot environent? I would have though they would not have appeared in CDP if they were corrupt?
 
I did not set this up in the first place so a little puzzled at the moment? Nothing has changed on the config bar using a different NTP server on the network?

View 1 Replies View Related

Cisco Wireless :: 1131AG - How To Disable Syslog Counter

Oct 24, 2012

I can't figure out how to disable the syslog counter on my 1131AG WAP.  See the below example log, the counter (number 3614) is right next to the hostname and increments with every syslog message:
 
Oct 25 07:31:10 airhead 3614: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   7c61.93a4.8332 Associated KEY_MGMT[WPAv2 PSK]
  
I've tried both of the following commands, neither one removes the counter:
 
no service sequence-numbers
no logging count
Version Info:
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.4(10b)JDA, RELEASE SOFTWARE (fc1)
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(8)JEA, RELEASE SOFTWARE (fc2)
  
how to rid the syslog counter

View 1 Replies View Related

Cisco Wireless :: 1131AG AP With 5508 Controller Lighting?

Jun 5, 2013

I had deployed Fifty 1131AG AP with Cisco 5508 Controller, the problem is some APs giving a orange ligth and some of them didn't flashing "there Led is Off"

View 8 Replies View Related

Cisco Wireless :: 1131AG And Radio Reset Code 46?

Apr 24, 2012

I have a problem with one of our 1131AG AP,  B/G radio go down:
 
show controller dot11Radio 0:
(...)
Last radio reset code: 46
Radio resets - total:2946 retries:0 failed:0
Reset Stats: Start Cnt: 2742, Recovery: Cnt 33, Last Ret: 20, Fails: 0, Recvry Status: Stalled NO, In Prog NO
Code/Count: 37/00025 46/02851 51/00005 54/00030
Code/Count: 62/00001 67/00001 71/00033
 
Although I was not able to find any information about this reset code in Cisco documents. What is the reset code 46?What can i do?

View 7 Replies View Related

Linksys Wireless Router :: Can E1200 Be Bridges Wirelessly

Sep 26, 2012

Can the e1200 be bridges wirelessly? Or does it have to hardwired?

View 7 Replies View Related

Wireless Bridges To Pair Up With Netgear WNDR 3700?

Oct 13, 2011

I bought this wireless router about a year+ ago, and it's just great. It's attached to the cable modem "downstairs" and right now it supports 2 smartphones wirelessly plus an ancient wired cable to an "upstairs" home office.

I'd like to improve overall performance with a wireless bridge to a gigabit hub in the upstairs office. I'd also like to add a second wireless bridge so I can stream movies to a box that would be attached to my TV, which does not have built-in wireless access.

Trendnet seems to have some interesting wireless bridges, but in the past I had a Trendnet wireless router with really, reallly bad software.

View 10 Replies View Related

Cisco Wireless :: Results From Dot11 Link Test On 1400 Bridges?

Sep 11, 2012

Just did a dot11 radio link test on a point to multipoint 1400 series bridges. how to read the results of the test?

View 9 Replies View Related

Cisco WAN :: Find Out IP Address Of Aironet 1131ag Wireless Router?

May 30, 2011

How do I find out the IP address of a aironet 1131ag wireless router?

View 1 Replies View Related

Cisco Wireless :: Ap 1131AG Can't Access Device In Autonomous Mode

Nov 1, 2011

I have several AP's of 1131 AG used in autonomous mode. Recently one of them stops responding: i was not able to access web management or ping its NIC. I've tried with reseting device to default but no success, even more when i plug ethernet cable to AP port nothing happens even NIC led's are not blinking at all.

On CLI console i am seeing repeated constantly such entries:

*Mar  1 05:19:04.086: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Mar  1 05:19:05.086: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up

[Code].....
 
( i have new firmware but how to upload it without this interface running ? )

View 16 Replies View Related

Cisco Wireless :: How To Configure Hotspot On 1131ag Autonomous System

Jan 13, 2013

I have configured my AP with MBSSID and it does work fine. now I need to take it to the next level and introduce the 2nd ssid to be my home guest network for friends and family that are visiting.  What else should I include on this configuration to allow for a hot spot where the user logons and must authenticate themselves via a secure web browser before going out to the internet. Next question would be how to increase the security of the device and the AP.
 
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec

[Code].....

View 5 Replies View Related

Cisco Wireless :: 1131AG LWAP Status Led Yellow And Other Blinking Green?

Apr 10, 2013

I have a problem with three AIR-LAP1131AG-E-K9  that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).The SSID broadcast is enabled.On the switch the interface is up and there is traffic going in and out of the LAP.I tired power reset and factory reset for the APs but the problem remains the same.

View 2 Replies View Related

Cisco Wireless :: Multiple Aironet 1131AG Access Points And Same SSID?

Dec 22, 2009

We have multiple Cisco Aironet 1131AG devices, all wired on one Cisco L2 switch(2560)  who is connected to L3 switch (3550). We assigned one VLAN for access point in L3 switch who acts as vtp server (L2 switch is vtp client). All ap's will have static ip address and all will have same SSID and no security and they will be using multiple channels (ex. 1,6,11).  They will operate in 3 floor building for roaming wireless client. We won't using any wireless controller.

How to configure APs-all the same with different ip's, can we use L3 switch to create dhcp server for access points VLAN (pool for clients, and the rest for static ip for ap's)?

View 2 Replies View Related

Belkin Routers :: N300 Wireless Bridges Be Connected To Same Access Point

Nov 21, 2012

Can 2 N300 wireless bridges be connected to the same wireless access point ?

View 1 Replies View Related

Linksys Wireless Router :: E4200 And WET610N No Changes To Bridges Before Firmware Update

Feb 6, 2012

Okay so I have been using my E4200 router and WET610N bridges for a while now without any issues really until yesterday when I updated the firmware on the 4200 now none of my WET610N's (I have 2) can connect via wireless at all. At first I thought it was a a wireless issue but I have other devices that connect up just fine via wireless.I've made no changes to the router or the bridges before the firmware update.
 
If I hook the bridge directly to the router I can access it and configure it, but looking at the "Status" page, I see the bridge try and connect wirelessly but is quickly disconnected.  Range isn't an issue as in my testing the bridge was 2 feet from the router.I've update the bridges to the latest firmware and have verified a 100 times that the settings on both my router and the bridges are set correctly (when the bridges are hooked up via network card).

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved