Cisco Wireless :: Activate WAP4410N And AP-1131AG?
Mar 16, 2011
I have WAP4410N and AP-1131AG for the school lab's Access point. First, WAP4410N doesn't make connection to wired network.
There's no DHCP server in our school and uses below :
192.168.x.x ip address
255.255.0.0 Subnet
192.168.1.254 Gateway
210.220.16.7 DNS address.
So I seted these settings on the configuration page, but when I connect to the WAP4410N wireless, I can't connect to the internet. Problem reporter in Windows 7says there's IP adress problem on the access point. ...but the ip address is correct. I did everything on the manual ....
Second, AP-1131AG. I entered with console cable and changed the ip address. And I enabled wireless radio(default:disabled) but I cannot find SSID with wlan. I added SSID on SECURITY-SSID manager. It says 'interface on' on 802.11a/g, but it is the same. I can't find SSID. other labtops can't, too.. tried using vlan. FAILED....
View 5 Replies
ADVERTISEMENT
Apr 30, 2011
I have the following equipment:
Cisco 871W router
2x WAP 4410N APs running 2.0.3.3
I currently have 1 AP connected to the router via copper. The AP to AP link is over 802.11. I have attached a diagram reflecting the current topology.
The AP-to-AP link will come up utilizing B/G/N mixed mode; however, the connection is basically unusable. About 30% of the traffic is dropped, while the packets that do make it have a consistently volatile latency, anywhere from 15 to 1500 ms. I have had success using G-only and B/G mixed. The link is stable (I have had the best results with B/G). The problem is, I didn't buy the 2nd 4410N to run the G protocol. I would like to connect the APs running either B/G/N (hopefully negotiating to N) or N only. I am wondering if there is a certain configuration I can utilize (perhaps using WDS repeater or bridge versus Wireless Client/Repeater?), or a firmware upgrade set for release that can make this happen for me.
View 1 Replies
View Related
Feb 27, 2012
I can configure two APs as a bridge with one as an AP with RMW enabled, and the other in WGB mode. I have three VLAN, each configured on both APs with their own SSID. Each switch (cisco switches) port is in trucking with only the three vlan allowed. The APs are associating with each other but not passing VLAN traffic.
View 8 Replies
View Related
Jun 9, 2010
On autonomous AP's one can disable the bright status LED using the "led ....." command. But how can I disable the LED on a LAP-1131AG? The AP hangs in a bedroom so the light is quite annoying.
View 3 Replies
View Related
May 31, 2012
My AP 1131AG is not light weight mode and not able to boot. I have captured logs from consle port it stuck up after following error:
Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
[Code].....
View 3 Replies
View Related
Jun 5, 2011
IOS of my LAP 1131AG is corrupted. It is giving error messages while booting and asks for boot image.
View 2 Replies
View Related
Apr 2, 2013
My customer has an 1131AG AP, andhas Problems with joining to the controller. I did a debug and have the following output. The WLC (5508) shows the AP with Primary SW version as 3.0.51.0. this Release does not showup in any compat matrix! It seems to start downloading the software. after a while it stops with the bolded output, twice the same Bytecount!?
*spamApTask0: Apr 03 09:55:59.998: 68:ef:bd:94:e7:9c 5179392 Bytes Transferred to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.097: 68:ef:bd:94:e7:9c Received LWAPP
[Code].....
View 22 Replies
View Related
Feb 14, 2013
I have succeeded in turning the AP from autonomous into LWAPP mode with the Ugrade tool. The AP has been loaded with c1130-rcvk9w8-tar.124-10b.jda due to the upgrade tool version 3.4,After reboot, the AP appears on the vwlc (YES!) however as you can see in APvwlc.jpg the AP now have version 3.0.51.0.I need the AP to be loaded with version 7.3.101.0 with FlexConnect mode.
View 24 Replies
View Related
Jul 27, 2012
I have a dozen clients on an 1131AG and they cannot ping each other. I get a reply but it says destination host unreachable.
View 4 Replies
View Related
Jul 25, 2012
We have six 1131AG WAP's, lightweight, managed through a 2514 controller. We have a Windows 2008R2SP1 domain. Wireless users can connect to the network, and log on to the domain without any apparent 'issues'. They can access domain resources. However, they cannot browse the domain in Network Neighborhood. Interestingly, they can map a drive to shares on the servers, so long as they manually type in the path. This occurs with desktops running Windows 7 Pro, 32 and 64 bit; XP Pro SP1, 32 and 64 bit; ditto for laptops. The wireless NICs vary as to manufacturer, but do include Trendnet, Intel Centrino, and Intel Pro 100/1000. If I connect any of these machines via by wire, they can access all domain resources and browse the domain in Network Neighborhood in the usual manner.
View 3 Replies
View Related
Feb 16, 2010
I have a Cisco 2106 WLC, and a 1131ag Access Point. The 802.11a/g Radio "Operational Status" = DOWN. All other Radios are UP. I'm wondering if this is normal behavior as no clients are connecting to it over the 802.11a/g Radio.
View 8 Replies
View Related
Jan 21, 2013
I am planning to buy new AP for my existing setup. we are using 1131AG series AP, we need to go for new one with n supported with external antenna.
Current software version on controller is : 7.0.235.3
View 8 Replies
View Related
Oct 3, 2012
we have the WLC and 2 x Aironet AP's that is powers over PoE. The other day is was reloaded and since then the AP points are Blinking Red, according the the Aironet manaul this means some sort of boot error? They are also not appearing on the WLC from the GUI or CLI running a show ap summary. Interesting though I can see them via CDP, however they are not picking up IP's as they are listed as 0.0.0.0. After checking with colleagues I was told these were set statically.
Is it possible that the points not having IP addresses is a sign of a corrupt boot environent? I would have though they would not have appeared in CDP if they were corrupt?
I did not set this up in the first place so a little puzzled at the moment? Nothing has changed on the config bar using a different NTP server on the network?
View 1 Replies
View Related
Oct 24, 2012
I can't figure out how to disable the syslog counter on my 1131AG WAP. See the below example log, the counter (number 3614) is right next to the hostname and increments with every syslog message:
Oct 25 07:31:10 airhead 3614: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 7c61.93a4.8332 Associated KEY_MGMT[WPAv2 PSK]
I've tried both of the following commands, neither one removes the counter:
no service sequence-numbers
no logging count
Version Info:
Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.4(10b)JDA, RELEASE SOFTWARE (fc1)
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(8)JEA, RELEASE SOFTWARE (fc2)
how to rid the syslog counter
View 1 Replies
View Related
Jun 5, 2013
I had deployed Fifty 1131AG AP with Cisco 5508 Controller, the problem is some APs giving a orange ligth and some of them didn't flashing "there Led is Off"
View 8 Replies
View Related
Apr 24, 2012
I have a problem with one of our 1131AG AP, B/G radio go down:
show controller dot11Radio 0:
(...)
Last radio reset code: 46
Radio resets - total:2946 retries:0 failed:0
Reset Stats: Start Cnt: 2742, Recovery: Cnt 33, Last Ret: 20, Fails: 0, Recvry Status: Stalled NO, In Prog NO
Code/Count: 37/00025 46/02851 51/00005 54/00030
Code/Count: 62/00001 67/00001 71/00033
Although I was not able to find any information about this reset code in Cisco documents. What is the reset code 46?What can i do?
View 7 Replies
View Related
May 30, 2011
How do I find out the IP address of a aironet 1131ag wireless router?
View 1 Replies
View Related
Nov 1, 2011
I have several AP's of 1131 AG used in autonomous mode. Recently one of them stops responding: i was not able to access web management or ping its NIC. I've tried with reseting device to default but no success, even more when i plug ethernet cable to AP port nothing happens even NIC led's are not blinking at all.
On CLI console i am seeing repeated constantly such entries:
*Mar 1 05:19:04.086: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Mar 1 05:19:05.086: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
[Code].....
( i have new firmware but how to upload it without this interface running ? )
View 16 Replies
View Related
Jan 13, 2013
I have configured my AP with MBSSID and it does work fine. now I need to take it to the next level and introduce the 2nd ssid to be my home guest network for friends and family that are visiting. What else should I include on this configuration to allow for a hot spot where the user logons and must authenticate themselves via a secure web browser before going out to the internet. Next question would be how to increase the security of the device and the AP.
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[Code].....
View 5 Replies
View Related
Apr 10, 2013
I have a problem with three AIR-LAP1131AG-E-K9 that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).The SSID broadcast is enabled.On the switch the interface is up and there is traffic going in and out of the LAP.I tired power reset and factory reset for the APs but the problem remains the same.
View 2 Replies
View Related
Dec 22, 2009
We have multiple Cisco Aironet 1131AG devices, all wired on one Cisco L2 switch(2560) who is connected to L3 switch (3550). We assigned one VLAN for access point in L3 switch who acts as vtp server (L2 switch is vtp client). All ap's will have static ip address and all will have same SSID and no security and they will be using multiple channels (ex. 1,6,11). They will operate in 3 floor building for roaming wireless client. We won't using any wireless controller.
How to configure APs-all the same with different ip's, can we use L3 switch to create dhcp server for access points VLAN (pool for clients, and the rest for static ip for ap's)?
View 2 Replies
View Related
Sep 9, 2012
Im using 1131AG AP.Locally switched WLAN don't have problem.Authentication used: open/wpa-psk/wpa2-psk.Pinging the IP Address of the vWLC dynamic interface (WLAN-SSID Mapping) is ok, but with the gateway failed.
View 12 Replies
View Related
Jan 11, 2012
One of my customers asked me to configure a WLC 2106 and 2 LAP 1131AG (lightweight) for corporate/guest Wifi. Basically they want to implement a good wifi connection for internal use and a guest one with different QoS. The two lans should both have dhcp but they must bet kept segregated so that none from the Guest wifi can access corporate resources.
Since i've never configured a WLC from scrath i lightly supposed it would be quite straigh forward as routers and switches from Cisco.Unfortunately i was totally wrong.
I've downloaded the "Cisco Wireless LAN ControllerConfiguration Guide" (Soft.Release 6.0 June 2009) and after i red it i made up this workflow
for the configurations:
1) Configure Controller: (via serial)
- Set Management Interface parameters (IP- SM - Def GW - Dhcp server IP)
- Set Ap-Manager Interface parameters
- Virtual Interface parameters
- Set Admin Credentials
- Dhcp Configuration (internal and/or external)
2) Ap registration on the controller
- Configure vlan with dhcp request redirection to the dhcp server
3) Configure Wlan following customer's requests.
- Configure Wlan Auth for Corporate/Guest Wifi
- Configure QoS for both Wlans
Unfortunately i'm experiencing issue while trying joining the AP to the WLC.It appers that the IT guy of my customer tried to configure one of the Ap.In that Ap's flash i find files referring to a "mesh" configuration like: [code]
View 11 Replies
View Related
Jul 12, 2012
I have initially configured 2504 controller with necessary parameters. & we have LAP1131AG access Points. we have connected 2 Nos. of access points in network. we are getting Both AP connected with controller,Whenver i am trying to connect with this wireless network though SSID( currently, open authentication), laptop's not connecting with it. it shown error that " Windows was unable to connect to SSIDname "
View 4 Replies
View Related
Jun 27, 2011
A while back my faithful old IBM ThinkPad became very slow under the weight of too many applications and updates so I replaced it. Now I have decided I would like to revive it mainly as a games machine for my young grandson, so I wiped everything off it and reinstalled Windows XP Home Editon (it previously had XP Pro). It used to access the net via a wireless LAN card (IEEE802.11b/g) and this worked fine. I am now having difficulty reinstalling this device. I thought XP would just pick it up but it doesn't. I tried downloading a driver onto a memory stick using my new laptop but that doesn't work either.
View 8 Replies
View Related
Nov 9, 2011
I have two Wireless LAN Controllers 2504 and 8 APs 3502e. The WLCs are running software version 7.0.116.0. The problem is that I don't have the mesh option to configure indoor mesh inside the controller. In chapter 9 of Wireless LAN Controller Configuration Guide, Release 7.0.116.0 says that I have to go to Wireless Menu and select the AP. When I am inside the AP general page, the guide says I have to go to the Mesh tab, but that tab doesn't appear in the controller GUI. Do I have to use another image in the controller? Or do you have to use an special mesh code or something like that? Because in the download page of the controller it only appears the 7.0.116.0, two more new versions but there is nothing about mesh image.
View 5 Replies
View Related
Nov 16, 2011
i cant activate the hard Wireless N 1030.The interface activate many seconds and desactivate im self .
View 1 Replies
View Related
Sep 27, 2012
I recently installed 2 wlc 5508 with the latest software 7.3.101.0. I am not able to activate the Internal DHPC Server. The following message appears: "Error in setting dhcp scop leasetime".
View 5 Replies
View Related
Oct 7, 2011
I've just bought a L655D-S5164 and installed Windows 7 64. I get the wireless to work but the indicator light remains red (should be blue) and i can't activate/deactivate the wireless via Fn+F8. The wireless card is a RTL8188CE.
View 1 Replies
View Related
Mar 28, 2011
Mine is Inspiron N5030 Laptop(New). When i try to install Blue tooth driver it asks me "Activate Bluetooth Using Wireless Switch" . I tried to press f2 & fn+f2. But no changes. I went to BIOS and Everything was enabled and proper.
View 18 Replies
View Related
Dec 13, 2011
I have a Dell Inspiration - 1525 Laptop. I can't activate wireless network. I have seen a button in right side of computer, but problem is when I turn on the button the Bluetooth will be turn on and wireless not connected. How can I Connect Wireless net in my computer?
View 1 Replies
View Related
Mar 16, 2013
I wanto delete the Evalution License and i want to activate the permanent license. find the attached snapshot of License.
View 7 Replies
View Related
Sep 15, 2011
I have just recently bought a Dell inspiron m5030 and after downloading the driver for bluetooth from DELL website and trying to install it a window saying Activate Bluetooth using Wireless Switch is shown. I pressed Fn+F2 but nothing happened.
View 8 Replies
View Related
