Cisco Wireless :: Laptop Is Not Connecting With 2504 Controller Based 1131AG Access?

Jul 12, 2012

I have initially configured  2504 controller with necessary parameters. & we have LAP1131AG access Points.   we have connected 2 Nos. of access points in network.  we are getting Both AP connected with controller,Whenver i am trying to connect with this wireless network though SSID( currently, open authentication),  laptop's not connecting with it. it shown error that " Windows was unable to connect to SSIDname "

View 4 Replies


ADVERTISEMENT

Cisco Wireless :: WLC 2504 - Setup Guest Access On The Controller

Jun 4, 2012

I have setup guest access on the controller and this is not working at the moment. DHCP server setup on the controller for the Guest users. You are able to connect (get ip address from controller) and the browser gets redirected to 1.1.1.1 but then page can not be displayed instead of the login page.

View 10 Replies View Related

Cisco Wireless :: 2504 Controller Can Support 1552E Access Point?

Jul 27, 2012

Question about cisco 2504 wireless controller, is it support cisco 1552E outdoor access point? If NO provide me the correct series/model.

View 9 Replies View Related

Cisco Wireless :: 2504 Controller With 3 Aironet 1142 Access Points

Mar 16, 2013

I have installed/setup a cisco 2504 wireless controller and 3 aironet 1142 access points using the basic config on a windows sbs 2008 domain, the problem is that the clients that are connected to the 2504 aint getting the there ip addr from the AD but from the wireless controller, and there cant reach the clients on wifi from the clients that are connected to lan, is there anyway that i cant change this so that a client on lan can see the client on wlan and vice versa.

View 5 Replies View Related

Cisco Wireless :: 1131AG Not Joining To Controller (7.4.100)

Apr 2, 2013

My customer has an 1131AG AP, andhas Problems with joining to the controller. I did a debug and have the following output. The WLC (5508) shows the AP with  Primary SW version as 3.0.51.0. this Release does not showup in any compat matrix! It seems to start downloading the software. after a while it stops with the bolded output, twice the same Bytecount!?
 
*spamApTask0: Apr 03 09:55:59.998: 68:ef:bd:94:e7:9c 5179392 Bytes Transferred to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.097: 68:ef:bd:94:e7:9c Received LWAPP

[Code].....

View 22 Replies View Related

Cisco Wireless :: Setup 2504 WLAN Controller And 1142N Access Point?

Jun 13, 2013

We are planning to setup a new WLAN using Cisco 2504 WLAN Controller and 1142N Access Point. Is it possible to create individual user accounts for the users those who all are connecting to this WLAN Network by using the 2504 WLAN Controller ?

View 1 Replies View Related

Cisco Wireless :: 1131AG AP With 5508 Controller Lighting?

Jun 5, 2013

I had deployed Fifty 1131AG AP with Cisco 5508 Controller, the problem is some APs giving a orange ligth and some of them didn't flashing "there Led is Off"

View 8 Replies View Related

Cisco Wireless :: Manually Add Access Point To 2504 Wireless Controller

Sep 18, 2012

We have a 2504 Wireless Controller and it works great!We currently have 6 Access Points (Aironet 1252) connected.We just added the sixth one a few weeks ago and with a properly configured and fully functioning Wireless Controller, it was super easy.Now, I have been assigned to add another Access Point, but at a remote site.The plan is to have up to three or more APs at this remote location and we want them to talk back to the Wireless Controller.We have plenty of licences on our current Wireless Controller.Do do not want to spend the funds for another Wireless Controller and more licenses.
 
1. How does one manually add a Aironet 1252 to the 2504 Wireless Controller
 
2. If the AP is on a different subnet than the Wireless Controller, how does one get it registered?
 
3. The best for last: Can a Aironet 1252 talk to a 2504 Wireless Controller over a WAN link?

View 3 Replies View Related

Cisco Wireless :: 5500 / Controller Versus Cloud-based (Controller)

Mar 31, 2013

We are trying to navigate the waters in choosing between a in-house, controller-based, wireless network solution or a cloud-based solution. We have been presented with the usual suspects in cloud-based (Aerohive, Meracki, etc) and with Cisco (5500) and Aruba on the other side. We are a multi-campus organization with approx. 200 APs.Any hard reasons why go with a controller-based vs. cloud-based solution? If we must keep the conversation limited to Cisco, why go Meracki over Cisco's WLC solutions or vise versa?

View 1 Replies View Related

Cisco :: 2504 - Access Point Not Joining Correct Controller

Apr 4, 2013

I am trying to setup a 2504 Wireless Controller with a few  AIR-AP1262N-E-K9 Access Points. But i'm having trouble getting the access points to connect to the controller.The controller and AP's are setup at a local network at one of my customers. They are part of a quite large organization and are therefore connected to some of their other divisions in different contries via MPLS. The DHCP and DNS servers are therefore on a different subnet.I have confirmed that the Access Points do get a correct IP from the DHCP server and that i am able to ping from the controller to the AP. When looking at the controller it does not receive any join requests from the AP's. I have setup a console connection to the controller and 1 AP, so i can view debug information.Most guides mention that you can run different LWAPP commands from the CLI on the AP like show lwapp for example. But i am not able to run any of these LWAPP commands on my AP.

View 8 Replies View Related

Cisco Wireless :: WLC 2504 Authentication Based On AD / LDAP

May 17, 2012

What are the possibilities for configuring a WLC to authenticate WLAN users based on their Active Directory user account?
 
Is this possible by setting up local EAP on the WLC?
 
I’ am looking for a solution where there are no changes to the Domain Controller involved and also no setting op IAS/RADIUS.
 
WLC:2504

View 8 Replies View Related

Cisco Wireless :: 2504 -configure MAC Authentication With Certificate Based

Jan 8, 2013

I have cisco 2504 WLAN controller with 7.4 IOS. My query is can I configure the MAC authentication with certificate based. And without using any external servers like Radius, ACS and LDAP.
 
May I know, If there is a option on WLC…

View 4 Replies View Related

Cisco Wireless :: Adding A Second 2504 AP Controller

Aug 2, 2012

I currently have a single 2504 Controller managing 50 AP's.  I am adding a Second 2504 AP Controller with 15 Lic to manage an additional 10 AP's.  My current 2504 has each port configured for my four subnets that and it is managing AP's in 4 buildings.  Should I configure the new 2504 the same way so that it can see all four sites?  All so if the main 2504 goes down can the second 2504 take over even thou we will be out of lic?

View 7 Replies View Related

Cisco Wireless :: Upgrade Controller 2504 From 7.0 To 7.4?

Jun 16, 2013

upgrade on the wireless controller 2504  from 7.0 to 7.4 is direct upgrade.My customer  faced problem by upgrading the software 7.0 to 7.4 directly and the image hang.how should proceed recover the image 7.4/

View 7 Replies View Related

Cisco Wireless :: 2504 Controller - Can AP Be Set With Static Channels

Nov 11, 2012

We have a Cisco 2504 controller and approximately 35 AP's. Some of the AP's are located directly above each other (on another floor). When I run a basic annalyzer, it appears that there is some adjacent AP traffic, the controller has some of the close AP's with the same channel, so there is some RF interferance. The AP's currently are all setup for "G" and majority of the AP's are 1200 series, most of them are 1242's. Should and can the AP's be set with static channels so that there is no adjacent signals? If so where in the controller can that be done?

View 3 Replies View Related

Cisco Wireless :: 3602 AP Cannot Join 2504 Controller

Oct 16, 2012

This is a new setup and has not worked yet. I have multiple 3602 APs and one 2504 Controller. I thought initially I could plug-in an AP into one of two POE Ports on the 2504. During debug mode I see that it has low power, was suprised that the 2504 switch can't fully power the AP? Is this correct?Anyways I have another POE switch that I am using with ample power. The configuration for my wireless is that it will be completely segmented off of my internal network as this is for guest access. So DNS servers are external so I cannot create host entries for the AP to discover the controller. With that being said I believe that is just one way for the discovery process to happen. I have my controller management interface and DHCP scope on the controller on the same subnet plugged into the same POE switch. The AP does seem to get a DHCP address and I can ping the controller from the AP. I cannot get any further then that. I will not join the controller and the radios get disabled. I get messages such as "discovery response from MWAR is rejected. I will post a debug log of the AP and its bootup process. This is new equipment so I would assume the firmware is somewhat up-to-date and the 3602 AP is somewhat the latest model.

View 3 Replies View Related

Cisco Wireless :: 2504 Controller - Best Way To Have Internet Only Wi-Fi Network

Nov 29, 2012

Our current way of configuration for this is standalone ap's with multiple ssid's. The main network ssid's are on the 10.0.0.0 networks. The internet only ssid is on the 192.168.1.0 network. ( this is a wireless network only,no wired) They all get there dhcp address from a layer 3 switch. To prevent the wireless 192.168.1.0 intenet only network from getting to the 10.0.0.0 networks, we just put a simple source & destination deny acl on the in vlan interface of the 192.168.1.0 network on the layer 3 switch.Now that we are impementing a Cisco 2504 controller, the management and ap manger are both on the 10.0.0.0 network.( both on port 1 with dynamic ap manager enabled)  I can setup as many ssid's on the 10.0.0.0 network and they all work fine. But when I setup the 192.168.1.0 internet only ssid it will not connect. I'm assuming that its because the 192.168.1.0 network or anyone trying to connect and use that network has to go through the controller located on the 10.0.0.0 network. I'm thinking that the acl on the vlan interafce is the problem.So, if I'm correct, what is the best way to setup a separate internet only network through the private networks?

View 7 Replies View Related

Cisco Wireless :: Does 2504 Controller Support CAD Or JPG Drawings

Jun 11, 2013

Does the 2504 Wireless Controller support cad or jpg drawings? I have not been able to find in any of the menus.

View 1 Replies View Related

Cisco Wireless :: Enabling Netflow On A 2504 Controller?

Feb 28, 2013

I just completed setting up a AIR-CT2504-K9 controller with 9 APs with RADIUS on the private WLAN and an open guest WLAN; I want to enable netflow exports to a collector, but see no place in the GUI to do this and no obvious CLI commands.

View 1 Replies View Related

Cisco Wireless :: 2504 Controller Association Latency

May 21, 2013

-WLC 2504
-AP1602
-SW  7.4.100.0
 
We have 22 x AP1602.5 of them show up in the WLC with Controller Association Latency of around 1 minute and 10 seconds.The other 17 all have latency around 10 seconds.
 
1. What are possibile causes for high value of association latency?

2. Could high-value association latency be an indication of badly working wifi for data traffic?

View 1 Replies View Related

Cisco Wireless :: 2504 Controller - How To Generate Graphs

May 19, 2013

I'm supporting a 2504 wireless controller with 3 aps in a health clinic.  I'm interested in generating some useful information for the owners of the device such as radio utilization (It'd be really nice if there were some graphs). how I can generate these graphs without SNMP monitoring or something like Cisco Prime Infrastructure?

View 4 Replies View Related

Cisco Wireless :: Migration 2106 To 2504 Controller?

Jan 6, 2013

I have a question to migrate a customer from a 2106 controller to a 2504 controller. Can I use the configuration file with both controllers having the same version?
 
Or is there another way not having to do it again manually? The old configuration is OK, only the hardware is end of sale.

View 19 Replies View Related

Cisco Wireless :: Not Able To Get DHCP IP Via 2504 WLAN Controller

Jan 7, 2013

I have a Cisco Wlan Controller 2504 with 1042N AP (3-nos) every thing was working fine from past 2 months. Now i am getting a issue with clients which are connected to the wireless AP, they are not able to get an dhcp IP address from the 2960 Switch (DHCP Server). The clients are getting IP address as 0.0.0.0. [code]

View 36 Replies View Related

Cisco Wireless :: WLC 2504 - Setup Guest Wi-Fi On Controller?

Jun 4, 2012

I have setup guest access on the controller and this is not working at the moment.
 
DHCP server setup on the controller for the Guest users.
 
You are able to connect (get ip address from controller) and the browser gets redirected to 1.1.1.1 but then page can not be displayed instead of the login page.

View 2 Replies View Related

Cisco Wireless :: 2504 Controller Crash After Upgrade Through Web GUI To 7.2

Dec 16, 2012

Any online 2504 controller crash after upgrade to the point where even console port does not put anything out? Perfectly working 2504 running 7.0.116 ran upgrade through web GUI to 7.2. GUI showed perfect transfer, save etc... Asked for save before reboot. Select yes. Controller reboot and now it sits with following status lights:Power-greenSYS - amber blinkingALM - amber solidNothing out of console.

View 8 Replies View Related

Cisco Wireless :: Can't Register AP 1231 On 2504 WLC Controller

Apr 28, 2013

WLC shows the next error.
 
AP with  MAC 00:1e:13:10:40:59 (AIR-AP1231G-E-K9    ) is unknown.
 
I updated the AP to lightweighd firmware using upgrade tool. But upgrade tool generate the csv files empty so I had no idea about Hash key, so I resetted the APs to default values.
 
WLC still doesn't register them.
 
How Can I register the APs? The version of the WLC is 7.3.101.0

View 4 Replies View Related

Cisco Wireless :: 2504 - 1042 AP Registration With Controller

Jul 21, 2012

I ordered controller 2504 and will arrive soon. I want to know that after configure the initial setup of 2504 (i.e. AP manager , Management IPs etc) and defining the DHCP for AP. Will the 1042 lightweight AP will register with the controller automatically or i need to manually define the AP (MAC address) on WLC. and also whether the Option 43 and 60 are correctly defined?
 
Management Interface: 10.10.22.15
AP Manager Int: 10.10.22.16 
ip dhcp pool WLAN103
network 10.10.3.0 255.255.255.0
[code]...

View 4 Replies View Related

Cisco Wireless :: Ap 1131AG Can't Access Device In Autonomous Mode

Nov 1, 2011

I have several AP's of 1131 AG used in autonomous mode. Recently one of them stops responding: i was not able to access web management or ping its NIC. I've tried with reseting device to default but no success, even more when i plug ethernet cable to AP port nothing happens even NIC led's are not blinking at all.

On CLI console i am seeing repeated constantly such entries:

*Mar  1 05:19:04.086: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Mar  1 05:19:05.086: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up

[Code].....
 
( i have new firmware but how to upload it without this interface running ? )

View 16 Replies View Related

Cisco Wireless :: Auth Methods 2504 Controller / 2600 AP

Jan 24, 2013

I have a 2504 controller and 2 2602 access points.  I have managed to get them connected ok to the controller.  Now I'm in the home stretch here trying to figure out how to authenticate clients to active directory 2003.I have followed a really good guide on setting up the windows 2003 CA server and have got my certificates installed ok on the controller.It looks as though I have to install the client certificate on each client laptop??    Is there a method other than client certificates with active directory?

View 26 Replies View Related

Cisco Wireless :: DHCP With Anchor Controller With 2504 And 5508

Nov 7, 2012

All controllers are in version 7.2.111.3.C1 is a 5508, it is ou anchor controller.C2 is a 5508, it is a big site controller.C3 is a 2504, it is a small site controller. C2 and C3 are in the same mobility group than C1 (and all is up up in mobilty managment). When "DHCP Addr. Assignment" is enable on C1 : Clients on C2 received their IP address by our external DHCP server via C1 and the guest tunneling betwenn C1 and C2 and all is working fine. Clients on C3 don't received their IP address by our external DHCP server via C1 and the guest tunneling betwenn C1 and C3, so nothing work.

View 4 Replies View Related

Cisco Wireless :: Migrating WLAN Controller 2125 To 2504

May 29, 2012

I will migrate a Cisco WLAN Controller 2125 to 2504,So I have one question?I need to make all configuration into the new Wlan Controller or I can migrate with one tool or something else?

View 15 Replies View Related

Cisco Wireless :: Configuration Between Controller 2504 And Windows 2008?

Nov 25, 2012

I am actually working in configuring a wireless controller 2504 integrated a windows 2008 server as radius server for authenticating the network users registered in a windows active directory database. The Radius server is a Windows 2008 Server with the rol of Network Policy Server.
 
I have been following a pair of documents in Internet, but it doesn't work yet.
 
Which authentication method should i use?...the Windows 2008 NPS doesn't work wtih LEAP, should i use PEAP or there is an another recomendation to authenticate the windows active directory users?
 
configuration tested working between a cisco wireless controller and Windows 2008 NPS as Radius Server for authenticating the windows network users.

View 11 Replies View Related

Cisco Wireless :: WCS 7.0172 Template Support For 2504 Controller?

Jun 11, 2013

I attempted to assign a User Roles template to a## 2504 controller and if failed with message stating controller version not supported. My current WCS version is 7.0172, if I upgrade to the lastest version will that resolve the template issue?

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved