I have setup guest access on the controller and this is not working at the moment. DHCP server setup on the controller for the Guest users. You are able to connect (get ip address from controller) and the browser gets redirected to 1.1.1.1 but then page can not be displayed instead of the login page.
View 10 RepliesI have setup guest access on the controller and this is not working at the moment.
DHCP server setup on the controller for the Guest users.
You are able to connect (get ip address from controller) and the browser gets redirected to 1.1.1.1 but then page can not be displayed instead of the login page.
We are planning to setup a new WLAN using Cisco 2504 WLAN Controller and 1142N Access Point. Is it possible to create individual user accounts for the users those who all are connecting to this WLAN Network by using the 2504 WLAN Controller ?
View 1 Replies View RelatedWe are deploying 3600 AP's with a 2504 and would like to create multiple SSID's that are mapped to unique VLANs so we can control the traffic at the Firewall. We have the 2504 up and running with AP's but there appears to be no where in the 2504 controller Web GUI to configure a VLAN mapping to an SSID. Any pointers to documentation on how to configure?
View 1 Replies View RelatedI have 2 APs, Cisco Aironet 1040, and 2504 WLC.Is it possible to configure guest access (Guest SSID/VLAN and Corporative SSID/VLAN) without dedicated guest WLC in DMZ?
View 4 Replies View RelatedI would like to setup a 2504 to have one Guest WLAN and one Staff WLAN with a controller port for each WLAN connected to different devices.
I would prefer to connect the WLC Guest port to an ASA 5510 and the WLC Staff port to an internal 2960S switch. Will this work? I haven't setup a 2500 series controller previously.
Question about cisco 2504 wireless controller, is it support cisco 1552E outdoor access point? If NO provide me the correct series/model.
View 9 Replies View RelatedI have installed/setup a cisco 2504 wireless controller and 3 aironet 1142 access points using the basic config on a windows sbs 2008 domain, the problem is that the clients that are connected to the 2504 aint getting the there ip addr from the AD but from the wireless controller, and there cant reach the clients on wifi from the clients that are connected to lan, is there anyway that i cant change this so that a client on lan can see the client on wlan and vice versa.
View 5 Replies View RelatedI have initially configured 2504 controller with necessary parameters. & we have LAP1131AG access Points. we have connected 2 Nos. of access points in network. we are getting Both AP connected with controller,Whenver i am trying to connect with this wireless network though SSID( currently, open authentication), laptop's not connecting with it. it shown error that " Windows was unable to connect to SSIDname "
View 4 Replies View Relatedwe have 4408 controller purely for guest access and with local authentication..basically the guest access is free but needs an acc on the WLC on logon. when the user uses credentials to logon, after a while it gets disconencted and the user needs to reauthenticate. this happens every few mins. is there an option on the WLC to extend the session?
View 4 Replies View RelatedWe have a 2504 Wireless Controller and it works great!We currently have 6 Access Points (Aironet 1252) connected.We just added the sixth one a few weeks ago and with a properly configured and fully functioning Wireless Controller, it was super easy.Now, I have been assigned to add another Access Point, but at a remote site.The plan is to have up to three or more APs at this remote location and we want them to talk back to the Wireless Controller.We have plenty of licences on our current Wireless Controller.Do do not want to spend the funds for another Wireless Controller and more licenses.
1. How does one manually add a Aironet 1252 to the 2504 Wireless Controller
2. If the AP is on a different subnet than the Wireless Controller, how does one get it registered?
3. The best for last: Can a Aironet 1252 talk to a 2504 Wireless Controller over a WAN link?
I am trying to setup a 2504 Wireless Controller with a few AIR-AP1262N-E-K9 Access Points. But i'm having trouble getting the access points to connect to the controller.The controller and AP's are setup at a local network at one of my customers. They are part of a quite large organization and are therefore connected to some of their other divisions in different contries via MPLS. The DHCP and DNS servers are therefore on a different subnet.I have confirmed that the Access Points do get a correct IP from the DHCP server and that i am able to ping from the controller to the AP. When looking at the controller it does not receive any join requests from the AP's. I have setup a console connection to the controller and 1 AP, so i can view debug information.Most guides mention that you can run different LWAPP commands from the CLI on the AP like show lwapp for example. But i am not able to run any of these LWAPP commands on my AP.
View 8 Replies View RelatedI know that the 3600 series APs are not supported on the 4404 WLC. However, would the following scenario be supported? I would like to use the 4404 (software rel. 7.0) as a guest anchor with a 5508 (software release 7.2) as the foreign controller supporting series 3600 APs. I ask because the APs do not need to join the guest anchor.
View 7 Replies View RelatedI am running a /24 network in Active Directory with my ASA acting as gateway and firewall. Standard interfaces (Ethernet 0/0 as outside, Ethernet 0/1 as inside)
As of now I have no VLans set up, but I need to setup wireless Internet access for guests... I need directions on how to setup a Vlan with its on DHCP for these aguests... I can then make sure that my APs can be pointed to the same VLAN... I am not familiar with CLI, have generally used ASDM. I am currently running ASDM 6.3(1) on an ASA with version 8.3(1).
This is something I need to do quickly as we are expecting 20-40 "guests" shortly, and I don't want them to use our internal DHCP server addresses.
I have a requirement to set up a guest SSID for contractor so that they can use the internet while in the office.
Security say that all traffic on this SSID should be isolated and directed straight to the firewall, with no chance of contamination into the company network infrastructure.
With the 5508, my understanding is using the setting up a guest account functionality built in will achieve this, but all traffic would end up at the wireless controller. How do I then put a direct forward for all traffic to the firewall which will only affect the guest traffic?
Can I set up a guest wifi connection on my Cisco WLC 2504 if I already have WLANs set up inside my corporate network? I want to use port 4 and connect it directly to my ISP so that it is outside of the corporate network. I set up an interface with a valid IP from the ISP and created a "Contractor" WLAN to use that interface.
View 6 Replies View RelatedCant we create a guest user login with more than 30 days lifetime? In the lifetime field we can enter maximum 99 but it only allows up to 30
View 5 Replies View RelatedI recently got my Cisco wireless system working a few days ago and am back with a guest network. Our wireless system includes one 2504 controller and 2 2602i access points. So, I want a wireless guest network completely isolated from the LAN.
Here is what I have done.
I have created a new internal network and assigned 192.168.2.1 to an unused port on the firewall and 2.2 to a new controller interface with vlan 10. I can ping both 2.1 and 2.2 from the firewall and the controller. Basic network connectivity is working. The DHCP server is setup on this same firewall and configured only for this port. This address is referenced in the controllers interface.
A new w lan was setup and enabled. The proper interface group was selected on the w lan. I have left the default layer2 security.
As far as AAA servers tab in this wlan, this is where I am a little confused. I wish to just have a single log in for this guest network. I wasn't sure what to do so I went over to the Security tab and created a "local net users" account. I do not know how to reference the use of this under wlan, security, aaa servers. Should I check the box that says "local eap authentication"?? If so, I don't have a profile name in the drop down. What I'm looking for is the username/password to be stored locally on the controller itself since there will be only 1 account.
Under wlan, advanced tab, I do not have "Allow AAA override" checked. Should I?
Lastly, when I try to connect the client, it is not pulling a dhcp address. I wasn't sure if authentication was required before dhcp or the other way around so I'm not sure what to trouble shoot first, authentication or dhcp.
I have a cisco wlc 2504 is deploying authentication services to guest users toward a portal web customized and configured. I need to install my certificate verisign (certificate.cer) in to cisco wlc because my users don't like the page no trusted (The wlc is showing me ''There is a problem with this website's security certificate'') when they are trying to access to ssid to users guests.
View 2 Replies View RelatedIs it possible to allow certain websites to bypass the web authentication pages, so that they do not need to authenticate to get to our own website, but do have to if they wish to go anywhere else?Looking at a 5508 model at the moment
View 4 Replies View RelatedI recently setup a 2504 WLC that has two primary WLANs (internal and guest) which get their IP addresses from a central DHCP server using the local router's broadcast forwarding. Things seem to be working well for the internal wlan, but clients on the guest wlan don't seem to be getting IP addresses. If I give the client a static IP they are able to communicate across the wlan okay.
It is worth noting that I am using LAG between the controller and router and this guest wlan is really just a regular wlan (with PSK) that has an access-list applied to force it to the internet only. The access-list should be allowing dhcp requests through, but in any case, I removed the access-list and it made no difference.
Here is a debug client for a machine connected to the guest vlan (vlan 33). The internal wlan is on the 10.10.10.0/24 network (same as wired and same that the AP's are connected to) and the guest wlan is 10.33.0.0/16. I don't understand why I am seeing the dhcp request come from the internal vlan/ wlan first and it gets an IP address on this network. I then see a request on the guest wlan/vlan at which point it appears to get a valid IP address on the guest network (10.33.0.0), but the client never sees this. [code]
My customer need creates some separately web portal for some SSID (Guest and Staff), 01 web portal for Guest and 01 Web portal for Staff. Can WLC2504 can support this features ?
View 2 Replies View RelatedMy customer has multiple sites, each with a 2504 WLC.A data center with a 5508 in the DMZ acting as Anchor for the remote sites.ACS 5.x and NCS Prime.All guest users will egress to the internet via a Vlan in the DMZ.Authentication is currently web-auth on the Anchor, but will move to NCS once that is fully deployed.
Is it possible to put a printer in each site for Guest WLAN users to use?
I currently have a single 2504 Controller managing 50 AP's. I am adding a Second 2504 AP Controller with 15 Lic to manage an additional 10 AP's. My current 2504 has each port configured for my four subnets that and it is managing AP's in 4 buildings. Should I configure the new 2504 the same way so that it can see all four sites? All so if the main 2504 goes down can the second 2504 take over even thou we will be out of lic?
View 7 Replies View Relatedupgrade on the wireless controller 2504 from 7.0 to 7.4 is direct upgrade.My customer faced problem by upgrading the software 7.0 to 7.4 directly and the image hang.how should proceed recover the image 7.4/
View 7 Replies View RelatedI have registered here to clarify some things about VLAN's. There are so many (different) names and mentions that i found tat my vision gets blurry looking through all the info.I have a setup at a client where the Guest WiFi access needs to be separated from the normal LAN where all the normal devices are attached to. The guests are not allowed to reach the IP camera's and printer etc. etc. . I am trying to visualize how the traffic should flow but the Tagged, Untagged, PVID, Trunks and other names that i found make it difficult for me to see how it works together.
View 8 Replies View RelatedWe have a Cisco 2504 controller and approximately 35 AP's. Some of the AP's are located directly above each other (on another floor). When I run a basic annalyzer, it appears that there is some adjacent AP traffic, the controller has some of the close AP's with the same channel, so there is some RF interferance. The AP's currently are all setup for "G" and majority of the AP's are 1200 series, most of them are 1242's. Should and can the AP's be set with static channels so that there is no adjacent signals? If so where in the controller can that be done?
View 3 Replies View RelatedThis is a new setup and has not worked yet. I have multiple 3602 APs and one 2504 Controller. I thought initially I could plug-in an AP into one of two POE Ports on the 2504. During debug mode I see that it has low power, was suprised that the 2504 switch can't fully power the AP? Is this correct?Anyways I have another POE switch that I am using with ample power. The configuration for my wireless is that it will be completely segmented off of my internal network as this is for guest access. So DNS servers are external so I cannot create host entries for the AP to discover the controller. With that being said I believe that is just one way for the discovery process to happen. I have my controller management interface and DHCP scope on the controller on the same subnet plugged into the same POE switch. The AP does seem to get a DHCP address and I can ping the controller from the AP. I cannot get any further then that. I will not join the controller and the radios get disabled. I get messages such as "discovery response from MWAR is rejected. I will post a debug log of the AP and its bootup process. This is new equipment so I would assume the firmware is somewhat up-to-date and the 3602 AP is somewhat the latest model.
View 3 Replies View RelatedOur current way of configuration for this is standalone ap's with multiple ssid's. The main network ssid's are on the 10.0.0.0 networks. The internet only ssid is on the 192.168.1.0 network. ( this is a wireless network only,no wired) They all get there dhcp address from a layer 3 switch. To prevent the wireless 192.168.1.0 intenet only network from getting to the 10.0.0.0 networks, we just put a simple source & destination deny acl on the in vlan interface of the 192.168.1.0 network on the layer 3 switch.Now that we are impementing a Cisco 2504 controller, the management and ap manger are both on the 10.0.0.0 network.( both on port 1 with dynamic ap manager enabled) I can setup as many ssid's on the 10.0.0.0 network and they all work fine. But when I setup the 192.168.1.0 internet only ssid it will not connect. I'm assuming that its because the 192.168.1.0 network or anyone trying to connect and use that network has to go through the controller located on the 10.0.0.0 network. I'm thinking that the acl on the vlan interafce is the problem.So, if I'm correct, what is the best way to setup a separate internet only network through the private networks?
View 7 Replies View RelatedDoes the 2504 Wireless Controller support cad or jpg drawings? I have not been able to find in any of the menus.
View 1 Replies View RelatedI just completed setting up a AIR-CT2504-K9 controller with 9 APs with RADIUS on the private WLAN and an open guest WLAN; I want to enable netflow exports to a collector, but see no place in the GUI to do this and no obvious CLI commands.
View 1 Replies View Related-WLC 2504
-AP1602
-SW 7.4.100.0
We have 22 x AP1602.5 of them show up in the WLC with Controller Association Latency of around 1 minute and 10 seconds.The other 17 all have latency around 10 seconds.
1. What are possibile causes for high value of association latency?
2. Could high-value association latency be an indication of badly working wifi for data traffic?
I'm supporting a 2504 wireless controller with 3 aps in a health clinic. I'm interested in generating some useful information for the owners of the device such as radio utilization (It'd be really nice if there were some graphs). how I can generate these graphs without SNMP monitoring or something like Cisco Prime Infrastructure?
View 4 Replies View Related