We are deploying 3600 AP's with a 2504 and would like to create multiple SSID's that are mapped to unique VLANs so we can control the traffic at the Firewall. We have the 2504 up and running with AP's but there appears to be no where in the 2504 controller Web GUI to configure a VLAN mapping to an SSID. Any pointers to documentation on how to configure?
View 1 RepliesMy customer need creates some separately web portal for some SSID (Guest and Staff), 01 web portal for Guest and 01 Web portal for Staff. Can WLC2504 can support this features ?
View 2 Replies View RelatedI would like to setup a 2504 to have one Guest WLAN and one Staff WLAN with a controller port for each WLAN connected to different devices.
I would prefer to connect the WLC Guest port to an ASA 5510 and the WLC Staff port to an internal 2960S switch. Will this work? I haven't setup a 2500 series controller previously.
I have setup guest access on the controller and this is not working at the moment.
DHCP server setup on the controller for the Guest users.
You are able to connect (get ip address from controller) and the browser gets redirected to 1.1.1.1 but then page can not be displayed instead of the login page.
I have setup guest access on the controller and this is not working at the moment. DHCP server setup on the controller for the Guest users. You are able to connect (get ip address from controller) and the browser gets redirected to 1.1.1.1 but then page can not be displayed instead of the login page.
View 10 Replies View RelatedCan I configure Multiple SSID (Guest/Corporative) on Cisco Aironet 3600i AP via Cisco 2504 Wireless controller?
View 1 Replies View Relatedi have two 5508 ver 7.3.0, one is the primary and one is the guest controller. mobility is up and running. i have an exising guest ssid working with wpa2-psk and web authentication and its working fine but i require a second guest ssid that only uses a wpa2-psk for ipod/ipads as i cant use passive client on primary controller. i presently have the one vlan range and dhcp setup on the guest controller to give addressing to either ssid. i know you can have multiple ssid setup on the guest controller but in other sites i have only had one guest connection comming from the primary controller, just a primary controller on each sites was only creating one link to the same guest controler.
View 3 Replies View RelatedWe have been deploying 3502 APs remotely to locations with full T1s that backhaul to where I sit at HQ. Both the foreign and anchor controller are here at my location.
I am seeking to rate limit per user the bandwidth each client will get on the guest internet ssid. As you know this traffic is encapsulated in capwap between the AP and the controller so I cant use a standard ACL on the switch or router.
We are trying to keep the guest internet access usage in check on the T1 at any given site so the other ssid's & local lan traffic is not overly competing for the bandwidth.
I found the place to edit the default profiles in the controller but the documentation really isnt clear on best practices.
So I put it to you my fellow wireless engineers to suggest how you are implementing bandwidth management on your wireless guest internet.
Oh and here is my hardware & software levels.
5508wlc - forgeign
4402wlc - anchor
Software Version7.0.230.0
i have cisco wlc 2504 connected with cisco 3600 ap,now the customer required n bandwidth speed ,but in wlc am not able to enable n bandwidth for ssid.in radio policy of ssid also n bandwidth is not showing,only this bandwidth showing a/g,g,b/g, and all?
View 8 Replies View RelatedI know that the 3600 series APs are not supported on the 4404 WLC. However, would the following scenario be supported? I would like to use the 4404 (software rel. 7.0) as a guest anchor with a 5508 (software release 7.2) as the foreign controller supporting series 3600 APs. I ask because the APs do not need to join the guest anchor.
View 7 Replies View RelatedCustomer is interested in deploying the 3600 AP's but will not be able to replace all his 1231's, any chance there is a release between 7.0.220.0 and 7.1.91.0 that will support both AP's?
View 6 Replies View RelatedWe have an MPLS (layer 3) network 4 offices and a Data center. We are planning to install about 10 Access Points(3600 series) per office and have a controller(5508 series) in the Data center.
Questions:
1- Is this design possible, in other words, just one controller centralizing all Access point traffic in one controller in the Data center?
2- We would like to accomplish this in two phases:
A- install access points without controller handling authentication thru Microsoft IAS servers (current configuration with 1200 series)
B- Deploy wireless Controller in Data center and start migrating orphan AP to Controllers one office at a time.
I am working on my CCENT after getting my A+. I have an old 3600 router and I am following CBT Nuggets to configure it. CBT Nuggets seems to have an IOS that supports VLAN and IP Addresses and it looks like mine only goes up to Token Ring so it doesn't mirror the instruction. I know it's an old router but is there a software release (like the 12.4 maybe?) that would allow me to follow the CBT Nuggets more accurately so that I can set the switch up for IP Addresses and VLAN instead of limiting me to token ring?
View 1 Replies View RelatedIt,a possible configure 2 ssid with wlc 2504 and lap 1042n? It,s possible configure 2 ssid with support 802.11n?
View 1 Replies View RelatedCan I set up a guest wifi connection on my Cisco WLC 2504 if I already have WLANs set up inside my corporate network? I want to use port 4 and connect it directly to my ISP so that it is outside of the corporate network. I set up an interface with a valid IP from the ISP and created a "Contractor" WLAN to use that interface.
View 6 Replies View RelatedCant we create a guest user login with more than 30 days lifetime? In the lifetime field we can enter maximum 99 but it only allows up to 30
View 5 Replies View RelatedI recently got my Cisco wireless system working a few days ago and am back with a guest network. Our wireless system includes one 2504 controller and 2 2602i access points. So, I want a wireless guest network completely isolated from the LAN.
Here is what I have done.
I have created a new internal network and assigned 192.168.2.1 to an unused port on the firewall and 2.2 to a new controller interface with vlan 10. I can ping both 2.1 and 2.2 from the firewall and the controller. Basic network connectivity is working. The DHCP server is setup on this same firewall and configured only for this port. This address is referenced in the controllers interface.
A new w lan was setup and enabled. The proper interface group was selected on the w lan. I have left the default layer2 security.
As far as AAA servers tab in this wlan, this is where I am a little confused. I wish to just have a single log in for this guest network. I wasn't sure what to do so I went over to the Security tab and created a "local net users" account. I do not know how to reference the use of this under wlan, security, aaa servers. Should I check the box that says "local eap authentication"?? If so, I don't have a profile name in the drop down. What I'm looking for is the username/password to be stored locally on the controller itself since there will be only 1 account.
Under wlan, advanced tab, I do not have "Allow AAA override" checked. Should I?
Lastly, when I try to connect the client, it is not pulling a dhcp address. I wasn't sure if authentication was required before dhcp or the other way around so I'm not sure what to trouble shoot first, authentication or dhcp.
I have 2 APs, Cisco Aironet 1040, and 2504 WLC.Is it possible to configure guest access (Guest SSID/VLAN and Corporative SSID/VLAN) without dedicated guest WLC in DMZ?
View 4 Replies View RelatedI have a cisco wlc 2504 is deploying authentication services to guest users toward a portal web customized and configured. I need to install my certificate verisign (certificate.cer) in to cisco wlc because my users don't like the page no trusted (The wlc is showing me ''There is a problem with this website's security certificate'') when they are trying to access to ssid to users guests.
View 2 Replies View RelatedI've been searching high and low and although I've found many results of people having this same exact problem there doesn't seem to be a fix, or at least no one was kind enough to post one. I have many vlans but the 3 in question are 10, 20, 30.
-10 is for my laptops and desktops with an ip range of 192.168.10.10 - 192.168.10.50.
-20 is my home automation network with an orange of 192.168.20.20 - 192.168.20.150
-30 is my guest network with a orange of 192.168.30.84 - 192.168.30.89
I have a dell powerconnect configured with vlans as my core switch. I trunked a port on the switch assigning 3 vlans (10,20,30) and connected it to port 1 on the wrvs4400N. On the wrvs4400 I trunked port 1 tagging vlan 10,20,30. For some reason vlan 1 is untagged on port 1 and I don't know why. I also have a router connected to the powerconnect. Of the 3 vlans I mentioned vlan 10 and vlan 30 are the only ones with interfaces on the router. Vlan 20 is an internal network with a separate router and until I figure this out that router is physically turned off. Also the router currently turned on has no routes configured to connect my vlans. Currently there is no configured way to jump vlans.
No matter what ssid I connect to I get a dhcp response from vlan 10. all my test indicates that I'm actually on vlan 10. I get internet and I can hit all devices on vlan 10. If I connect to ssid guest and change my ip address to match vlan 30 I can not ping the gateway for vlan 30 and I have no internet access. Some times I get something different. Sometimes I get an ip address from vlan 1 on the powerconnect. If I renew my ip address then I'll grab one from vlan 10 but I should be getting one from 30 or none at all for vlan 20. The absolute crazy part is my droid sometimes gets a 192.168.4.x ip address. I don't have a 192.168.4.x network or dhcp scope anywhere on my network! If I physically plug into a port on the power connect I get to the correct network 10 out of 10 times. If I configure vlans on the other 3 ports on the wrvs4400 and physically plug in, I get to the correct network 10 out of 10 times. I've reset to factory a few times and I've been all inside and out of the wrvs4400. I have no clue what could be wrong with this thing.
I am tasked with configuring a 2504 wireless controller. Is it possible to assign an SSID to an interface that has dynamic ap management enabled?
Scenario:
Location1:
1) 10.0.0.0/24
2)192.168.0.0/24 DMZ
Location 2:
1) 10.0.5.0
Both locations are routable using network 1 at each location. However, I need to configure several access points and send them to location 2. These access points will communicate with the controller at location 1 on network 1. Two SSIDs will need to be on network 1 at location 1. The other SSID will be on Network 2 at location 1. This network is not routable.
I recently setup a 2504 WLC that has two primary WLANs (internal and guest) which get their IP addresses from a central DHCP server using the local router's broadcast forwarding. Things seem to be working well for the internal wlan, but clients on the guest wlan don't seem to be getting IP addresses. If I give the client a static IP they are able to communicate across the wlan okay.
It is worth noting that I am using LAG between the controller and router and this guest wlan is really just a regular wlan (with PSK) that has an access-list applied to force it to the internet only. The access-list should be allowing dhcp requests through, but in any case, I removed the access-list and it made no difference.
Here is a debug client for a machine connected to the guest vlan (vlan 33). The internal wlan is on the 10.10.10.0/24 network (same as wired and same that the AP's are connected to) and the guest wlan is 10.33.0.0/16. I don't understand why I am seeing the dhcp request come from the internal vlan/ wlan first and it gets an IP address on this network. I then see a request on the guest wlan/vlan at which point it appears to get a valid IP address on the guest network (10.33.0.0), but the client never sees this. [code]
My customer has multiple sites, each with a 2504 WLC.A data center with a 5508 in the DMZ acting as Anchor for the remote sites.ACS 5.x and NCS Prime.All guest users will egress to the internet via a Vlan in the DMZ.Authentication is currently web-auth on the Anchor, but will move to NCS once that is fully deployed.
Is it possible to put a printer in each site for Guest WLAN users to use?
Setup a WAP321 with the new 1.0.1.10 firmware. Setup 2 SSIDS:
WIRELESS (vlan:1)
GUEST (vlan:99)
The wap is plugged directly into a port on my router so I configured the port and additional vlan99 port. I have a DHCP scope assigned on the router to both the port and port.99 interfaces.clients on WIRELESS have no problem and work correctly, however when a client joins guest...a packet capture on the router port shows that a dhcp request is being received for the same MAC on both untagged and tagged 99 interfaces....thus it appears the WAP is not handling the vlans properly
16:07:10.566932 PortA, IN: IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from 84:c9:b2:78:fc:31, length 331
16:07:10.566947 PortA.99, IN: IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from 84:c9:b2:78:fc:31, length 331
I have two 1142n LWP ap converted into standalone, as client doesn't have any controller there. They just want to extend their network via wireless.
L3 switch (trunk port gig 1/48) -----> connected to AP1
L3 switch (trunk port 2/48) -----------> connected to AP2
client is looking for 3 vlans on the floor ( users might multiple vlans might associated same AP ). They have a dedicated DHCP/DNS server and he will be configuring 3 vlans on L3 switch with correct ip helper address on SVI interfaces.
I'm i allowed to created 3 SSID's on 1142n standalone AP ?
What would the various optiosn to achieve this requirement ? Is there any simplest way to achieve this ? Do i need to go for 802.1x ? I remember client told their users are authenticating by using AD for wired network. This is their first request for wireless environment
I currently have a single 2504 Controller managing 50 AP's. I am adding a Second 2504 AP Controller with 15 Lic to manage an additional 10 AP's. My current 2504 has each port configured for my four subnets that and it is managing AP's in 4 buildings. Should I configure the new 2504 the same way so that it can see all four sites? All so if the main 2504 goes down can the second 2504 take over even thou we will be out of lic?
View 7 Replies View Relatedupgrade on the wireless controller 2504 from 7.0 to 7.4 is direct upgrade.My customer faced problem by upgrading the software 7.0 to 7.4 directly and the image hang.how should proceed recover the image 7.4/
View 7 Replies View Relatedhow to setup a separate SSID for guests (without a password).
Basically, we have one SSID now called Mnet which has a WPA2 password. For guests coming in i want Mnet Guests where people can connect without needing a password. They should be able to use internet but not connect to LAN devices, how to accomplish this with this WAP321?
I am setting up a guest WLAN network on our existing 1242 AP's using a seperate VLAN. On most wireless devices which are on the company network/VLAN's, I have used WEP authentication with hex keys, and no broadcast. Obviously this cannot be the same for a guest internet connection.We want to have the VLAN/SSID in guest mode (which i have configured) for broadcasting, and then once someone selects the SSID on their laptop or smart phone, they are just prompted to authenticate with a standard alphanumeric password (example "guestwifi") instead of a 40 or 128 bit key.
I have searched all over and tried multiple things in the CLI on AP1, but can't seem to get anywhere.
Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies View RelatedWe have a Cisco 2504 controller and approximately 35 AP's. Some of the AP's are located directly above each other (on another floor). When I run a basic annalyzer, it appears that there is some adjacent AP traffic, the controller has some of the close AP's with the same channel, so there is some RF interferance. The AP's currently are all setup for "G" and majority of the AP's are 1200 series, most of them are 1242's. Should and can the AP's be set with static channels so that there is no adjacent signals? If so where in the controller can that be done?
View 3 Replies View RelatedThis is a new setup and has not worked yet. I have multiple 3602 APs and one 2504 Controller. I thought initially I could plug-in an AP into one of two POE Ports on the 2504. During debug mode I see that it has low power, was suprised that the 2504 switch can't fully power the AP? Is this correct?Anyways I have another POE switch that I am using with ample power. The configuration for my wireless is that it will be completely segmented off of my internal network as this is for guest access. So DNS servers are external so I cannot create host entries for the AP to discover the controller. With that being said I believe that is just one way for the discovery process to happen. I have my controller management interface and DHCP scope on the controller on the same subnet plugged into the same POE switch. The AP does seem to get a DHCP address and I can ping the controller from the AP. I cannot get any further then that. I will not join the controller and the radios get disabled. I get messages such as "discovery response from MWAR is rejected. I will post a debug log of the AP and its bootup process. This is new equipment so I would assume the firmware is somewhat up-to-date and the 3602 AP is somewhat the latest model.
View 3 Replies View RelatedOur current way of configuration for this is standalone ap's with multiple ssid's. The main network ssid's are on the 10.0.0.0 networks. The internet only ssid is on the 192.168.1.0 network. ( this is a wireless network only,no wired) They all get there dhcp address from a layer 3 switch. To prevent the wireless 192.168.1.0 intenet only network from getting to the 10.0.0.0 networks, we just put a simple source & destination deny acl on the in vlan interface of the 192.168.1.0 network on the layer 3 switch.Now that we are impementing a Cisco 2504 controller, the management and ap manger are both on the 10.0.0.0 network.( both on port 1 with dynamic ap manager enabled) I can setup as many ssid's on the 10.0.0.0 network and they all work fine. But when I setup the 192.168.1.0 internet only ssid it will not connect. I'm assuming that its because the 192.168.1.0 network or anyone trying to connect and use that network has to go through the controller located on the 10.0.0.0 network. I'm thinking that the acl on the vlan interafce is the problem.So, if I'm correct, what is the best way to setup a separate internet only network through the private networks?
View 7 Replies View Related