Cisco Wireless :: 2504 / Assign SSID To Interface That Has Dynamic AP Management Enabled?
Jan 3, 2012
I am tasked with configuring a 2504 wireless controller. Is it possible to assign an SSID to an interface that has dynamic ap management enabled?
Scenario:
Location1:
1) 10.0.0.0/24
2)192.168.0.0/24 DMZ
Location 2:
1) 10.0.5.0
Both locations are routable using network 1 at each location. However, I need to configure several access points and send them to location 2. These access points will communicate with the controller at location 1 on network 1. Two SSIDs will need to be on network 1 at location 1. The other SSID will be on Network 2 at location 1. This network is not routable.
View 32 Replies
ADVERTISEMENT
Aug 26, 2012
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
View 4 Replies
View Related
May 10, 2012
We are installing a 2504 with management on VLAN2. The management port is on interface 1 which is attached to a layer 3 3750. From other VLANs in the network we cannot manage the 2504 controller with the web manager. We are running the latest code, 7.2.103.0, since we are using 3600 APs. We have a TAC case open, but spent 3 hrs with them and they can't figure out the problem. TAC did some debugging and saw that the 2504 is ARPing for the address of the PC on the other VLAN instead of sending the packet to its default gateway. How to get success with the management interface on a VLAN and managing the controller from another VLAN?
View 2 Replies
View Related
May 29, 2012
Is it possible to assign IP addresses to remote site WIFI users from local DHCP server and forward all other traffic to 2504 WLC?
[WIFI Users] >--------<AP (DHCP server) >------ VPN ---------< WLC
View 1 Replies
View Related
Apr 29, 2013
I have a small motel and I provide net access to guests via the E3000 2.4Ghz band. There is no problem here. I also have set up the 5Ghz band for employee access. The networks are designated Bates Guest for the 2.4 Ghz network and Bates Private for the 5 Ghz network (yeah, believe it or not it really is the Bates Motel). As I said, the guest network is operating just fine. The private network on the other hand is giving me fits. The remote devices are not seeing the private network and, yes, the SSID is enabled. I can see and use it with my iPad no problem but my iPod does not. None of the remote users can see the private network. BTW I admin the router/network from a Win 7 desktop setup. Whats bugging me is how one of my two remote devices sees and uses the 5 Ghz network and other one does not.
View 9 Replies
View Related
Feb 29, 2012
It seems like the 4-ports switch in the 2504 can only one port can be used for management VLAN at a time ? I need all 4 ports to be untagged in the managment VLAN.
View 7 Replies
View Related
Sep 25, 2012
is it possible to Manage the 2504 Controller over a separate Interface. Exmaple: Port 1 is used as controller management interface (untagged) - AP's are connected to the same VLAN Port 1 is used for Guest Traffic (VLAN 3 tagged) Port 2 should be used to manage the WLAN Controller from the internal LAN. (tested with untagged, tagged, same issue)
with this Setup it is possible to ping the Port 2 IP-Address from the internal LAN but if you try to connect to the controller, the Browser shows "Site not reachable".
I also enabled "Management via Wireless" but without success. I also tried to add the "management" VLAN as tagged on the management Interface with the same effect, the controller is not manageable from the internal LAN. On 5508 WLAN Controller i have an similar setup, but with LAG Port enabled. There this works.
The only interface were i can manage the WLAN controller is from the management Interface.
View 1 Replies
View Related
Nov 3, 2012
It,a possible configure 2 ssid with wlc 2504 and lap 1042n? It,s possible configure 2 ssid with support 802.11n?
View 1 Replies
View Related
Jan 17, 2013
My customer need creates some separately web portal for some SSID (Guest and Staff), 01 web portal for Guest and 01 Web portal for Staff. Can WLC2504 can support this features ?
View 2 Replies
View Related
Apr 3, 2012
Can I configure Multiple SSID (Guest/Corporative) on Cisco Aironet 3600i AP via Cisco 2504 Wireless controller?
View 1 Replies
View Related
May 2, 2012
We are deploying 3600 AP's with a 2504 and would like to create multiple SSID's that are mapped to unique VLANs so we can control the traffic at the Firewall. We have the 2504 up and running with AP's but there appears to be no where in the 2504 controller Web GUI to configure a VLAN mapping to an SSID. Any pointers to documentation on how to configure?
View 1 Replies
View Related
Jul 29, 2012
Is it possible to use a 2504 wifi controller to manage compatible AP's across different subnets ?
View 2 Replies
View Related
Nov 7, 2012
How do i get the 12.4 code to assign a dhcp address to my ethernet interface from my server? I deleted the default config on the 1141 and searching has not turned up anything useful.
View 1 Replies
View Related
Jan 8, 2013
I'm getting familiar with an existing, working wireless installation that uses a 2504 controller (recently upgraded to 7.3.101.0).
From the documentation, it looks like there should be a "AP-manager" interface by default (static). There is not one.
Configuring the Management Interface (GUI) #
Step 1 Choose Controller > Interfaces to open the Interfaces page.
###
Figure 3-3 Interfaces Page
#
According to that document, there are 4 Static interfaces. On the one I'm working on, there are only two: "management" and "virtual." (There are also a couple of "Dynamic" interfaces that have been set up.)From reading the documentation, it sounds like there should be an AP-manager interface, and that this would have been there by default.
It also sounds like an AP-manager interface is needed:Information About the AP-Manager Interface ## A controller has one or more AP-manager interfaces, which are used for all Layer 3 communications between the controller and lightweight access points after the access points have joined the controller. The AP-manager IP address is used as the tunnel source for CAPWAP packets from the controller to the access point and as the destination for CAPWAP packets from the access point to the controller.
Question 1: If I do not have an AP-Manager interface, are the APs connecting at L2? Is there some way to tell on these controllers whether APs are connecting at L2 or at L3 using udp?
Question 2: Is it not the case that one AP-manager interface should be there by default? (I see in the docs that more than one can be created, but in that case I expect that the additional interface(s) would show in the list as "Dynamic" and not "Static.")
A bit of background: The customer network is largely one flat network now, and I'm planning on subnetting it, and routing from the closets up. I want to make sure what may need to be changed in this wireless setup before proceeding. (The main wireless users are also getting IP addresses on the same flat network, at this point. That obviously will change so that they are on their own subnet.)
View 5 Replies
View Related
Nov 28, 2012
I have a client with a WLC 2504 that wants to route "guest" users through a gateway appliance "radiusgateway.com" and all others through the network. It appears to me this would require the use of two fa ports on the WLC. One directly connected to the radiusgateway (which is connected to a switchport) and the other fa interface connected directly to a switchport bypassing the proxy server.
My issue is, "how do you segment the ssid traffic via the WLC". The interfaces cia the gui aren't that intelligent, there's an enable and logging drop down. Via the command line, I didn't see any methods of routing traffic.
View 1 Replies
View Related
Feb 24, 2013
I am using Cisco WLC 2504 for provisioning Wireless Connectivity over my Wired Environment. Have deployed 4 Access Points spanning my entire campus as per Customer Requirements. Created 10 SSIDs for Different Networks. Would like to know if there is any possibility of Broadcasting say a particular SSID XYZ on only two or 3 Access Points and keep broadcast disabled on Others.
integrating the authentication on these SSIDs using Active Directory Domain Credentials.
View 5 Replies
View Related
Aug 10, 2012
Having setup several WLC4402's in the past, I am posed with a new implementation that I have never tried before. I will be setting up a new 5508 that will ONLY be used for remote access-points in H-REAP mode. It is going into a data center and there will be no local LWAPP's.Is it still required to setup a dynamic interface on a network that will essentially only have the controller IP? Or can I serve all the AP's out of the single, untagged management interface (which I believe is also the old ap-manager interface now?)
View 2 Replies
View Related
Aug 1, 2010
I'm setting up a new 5508. I've used the config from a 4402, have successfully connected to the Service port to manage the device, but for some reason cannot connect to the Management interface. In this case, port 1.
The service port is connected to a Catalyst switch and grabbed an ip address (10.2.x.x subnet) no problem. I can access the 5508 via https using the SP. However, port 1 is connected to the same Catalyst switch, but on a different vlan (subnet 10.20.x.x). Both ends show that the interfaces are up, I can ping the interface from any other host on the network, but when I try to manage the device via https I cannot connect. We are using WCS and I cannot add the device from the WCS. About all I can do is ping that interface.
View 6 Replies
View Related
Jan 16, 2013
After I've upgraded software to the v7.3 and applied AP-SSO it made imposible to access the controller's gui via Service-port. So we tried to access it by management-port, but there is some problem too. It is not working from another subnets. But default gateway on management vlan is set correctly and I even tried to turn of all acl's on switch. WLC is only accessible from the same network. But at the same time wlc is replying on ping fine.All other protocols cannot connect to the controller.
View 3 Replies
View Related
Oct 19, 2011
I have got a 3502 setup and functioning in Office Extend mode. I have found one issue though. I have to set the checkbox on the my Management Interface to Enable NAT Address and put the external address in the box. Once this occurs no internal APs can join the controller.
Need setting this up with a single controller behind a router and not having to set the NAT Address for the Management interface? Should I setup a second interface on the controller to be for external management?
View 9 Replies
View Related
May 6, 2013
I have 2 x 5508 Wireless Controllers, 1 mgmt port on each as standard. I noticied something different between these controllers running the same code.I can bound a physical port to the mgmt interface on one controller but not the other (both interfaces are untagged)see below, this config appears on one controller but not the other? Is this something to do with the initial setup? How can I add Phyiscal information to the other controller mgmt interface, I cannot delete the mgmt interface. Physical InformationPort Number Backup Port Active Port Enable Dynamic AP Management?
View 2 Replies
View Related
Nov 1, 2010
I have a client with an AP541n, most recent firmware installed. When he logs into the management interface (via IP using Google Chrome browser), it will work for a few minutes and then just disappear. If he attempts to reload the page he gets a message similar to a website being down (page cannot be displayed). The idle timeout has been extended to 4 hours, but this can happen at any point while logged into the interface.
View 1 Replies
View Related
Mar 28, 2012
I've just reset our WISM2 in the test lab back to factory default as I needed to reconfigure the 6500 and the WISM2 itself. Bearing in mind I had it working before.I've just renamed and re-addressed some of the vlans so things flow better and make it easier to add more WISM2s in the future.Now I've run through the initial configuration and it's rebooted ok and show WISM status is showing Oper-Up and there's a port channel 407 been created as I would expect. However, I am unable to get to the management interface via GUI or SSH. In fact from the 6500 I can't even ping the management interface (but I can the service port).The Vlans have been changed in the 6500 config so it knows the native-vlan and service vlan etc and all the vlans are up/up.
View 17 Replies
View Related
Feb 24, 2013
I have a cisco wlan controller (2100) running software 7.0.235.0. I have the internal private wlan running off of port 1 and that is working fine with an internal dhcp server.Is it possible to setup another ssid (guest) and have the interface directly linked to a static ip on the WAN and also use the built in cisco internal dhcp server?
View 4 Replies
View Related
Mar 24, 2013
I wish to assign a MAC ACL to a layer 2 interface on an 887VA router but cannot seem to see how to do this.
View 2 Replies
View Related
Oct 16, 2011
I have a question regarding mlppp and bonding mpls T1 circuits. For the longest time we have been able to get by on one T1 circuit coming into our 3845 router. Well this T1 has now become congested and they are wanting to add bandwidth to this T1. We connect to the phone company via an MPLS T1 currently. So now it appears as though we are going to purchase another MPLS T1 circuit and bond the two T1's together. The way our network is currently set up, we utilize the same AS number on all of our remote routers regardless of location. Keep in mind I don't have any sort of mlppp set up at this moment, so unfortunately I can't post any configs. I'm just questioning the design portion and how to go about doing this.
Here is where my dilemma begins........
For every MPLS circuit we order on the remote end, we specifiy an IP for the remote router itself and one for the provider to assign to their equipment (the bgp neighbor statements). Now granted i'm no BGP extraordinaire, not even a novice really, but I don't understand how I am going to bring two T1 circuits into the same router (basically with 2 pairs of IP's). In order to bond the two T1's together, i'll need to create a multilink interface and assign an IP to that, but yet I still have 2 SETS of ip addresses. And if that isn't enough of a dilemma, I also need to spedify a neighbor statement in order for my AS to bind to the adjacent provider AS, but yet I have two IP addresses for that as well.
View 2 Replies
View Related
Apr 19, 2012
I have a cisco 878 router and I can’t assign ip address to it’s fast Ethernet interface. When I assign ip address give me this message: “you can not assign ip address to layer 2 interface”.
But I can not understand why give me this alert when I use a layer3 device?!
View 3 Replies
View Related
Oct 26, 2012
I have ASA 5505 with base license. I created 3rd vlan on it.it was created. but i am unable to assign IP to it. i assign ip address it takes it. But when i do sh int ip brief it does not show any ip.
Code...
View 7 Replies
View Related
Oct 13, 2011
How do i tell my firewall to start listen also on another outside ipadress assigned by my ISP? I have it used on other firewall right now. So my steps would be shutting down ip address assignment off old firewall interface. Assign that ip address to ASA5510 outside interface and configure NAT.
View 13 Replies
View Related
Jul 25, 2012
I need to configure a Cisco 2911. I need to give an interface in this module (VWIC3 - 4MFT-T1/E1) an IP address. My question is, how to assign an IP to an interface in this module.
My purpose is to get connectivity via T1 line to another router.
View 16 Replies
View Related
Feb 6, 2013
I am trying to harden my Nexus box and I am not able to ACL assigment command. Following are the commands I am trying to add.
interface cmp-mgmt module 5
Ip access-group NETWORK_MANAGEMENT_ACCESS in
View 1 Replies
View Related
Dec 13, 2011
I am trying to assign static ip address on vlan 1 interface , the model no of switch is SG300 & the firmware version is 1.1.2.0 .But whenever I type the IP address & press enter , a question is popped up asking for confirmation (switch0d851f(config-if)#ip address 1.1.1.1 255.0.0.0.
Please ensure that the port through which the device is managed has the proper settings and is a member of the new management interface.Would you like to apply this new configuration? (Y/N)[N] N )
View 3 Replies
View Related
Jun 29, 2012
I am getting this error on my PIX 535 with 8.0.4 code. The error is Error : OSPF/RIP cannot be enabled on failover interface, I am getting this error while trying to enable RIP on the firewall. The context is single mode and failover is enabled. When I am disabling the failover the Firewall is accepting the RIP configurations.
View 2 Replies
View Related
