Is it possible to assign IP addresses to remote site WIFI users from local DHCP server and forward all other traffic to 2504 WLC?
[WIFI Users] >--------<AP (DHCP server) >------ VPN ---------< WLC
I imagine I can use the framed-ip-address attribute to assign ip-addresses but there seem to be support for static ip addresses only?A bit of a drag when we're talking 200+ nodes.
View 1 Replies View RelatedI upgraded my SG500 switch firmware to 1.3.0.59, since there is a new functionality DHCP server v.4 well I must say I came accross the issue I cannot solve. DHCP server assign dynamic address - no hassles. troubles start with static IP hosts.I defined a couple of hosts with static address within the correct subnet. I tried with hardware address and client identifiers. no luck. my switch does not assign the IP address I assigned to the suitable mac address. to define it I use both CLI & Web.
ip dhcp pool host HP-Elliteaddress 10.10.11.7 255.255.255.0 client-identifier 01:d8:d3:85:cf:09:72client-name HP-Ellitedefault-router 10.10.11.1exit
ip dhcp pool host VAIO-Zaddress 10.10.14.108 255.255.255.0 hardware-address 54:53:ed:1c:a1:46
default-router 10.10.14.1exit
The 1130ag was the LAP model but I upgraded it to run in autonomous mode. My understanding is that it cannot assign IP addresses but I just want that confirmed. It is not connected to a WLC nor a server that can do DHCP.
View 5 Replies View RelatedI have a request to establish a site to site VPN with a customer. While collecting the information I give them our local network subnet which is a private subnet (192.168.5.0). They asked me if I could give them a public address instead. They can not work with the 192.168.5 subnet. Is this possible?
My side of the VPN is an ASA 5505 running 8.2(2). The other side i believe is a Checkpoint.
we have two ASA 5510s one in 8.4(4) and one in 8.2(5) in a site-to-site VPN setup. All internal traffic is working smoothly.Site/Subnet A: 192.160.0.0 - local (8.4(4)) Site/Subnet B: 192.260.0.0 - remote (8.2(5)) VPN Users: 192.160.40.0 - assigned by ASA When you VPN into the network, all traffic hits Site A, and everything on subnet A is accessible.
Site B however, is completely inaccessible for VPN users. All machines on subnet B, the firewall itself, etc... is not reachable by ping or otherwise.There are also some weird NAT rules that I am not happy with that were created after I upgraded Site A ASA to 8.4
Site A internal: 192.160.x.x External: 55.55.555.201(main)/202(mail)
Site B (over site-to-site) is 192.260.x.x External: 66.66.666.54(all)
I pretty much just have the basic NAT rules for VPN, Email, Internet and the site-to-site.What do I need to add for the VPN to be able to access the site-to-site network?
Here is my NAT config:
nat (inside,Outside) source static DOMAIN_LOCAL DOMAIN_LOCAL destination static VPN_Network VPN_Network no-proxy-arp route-lookup
nat (inside,Outside) source static DOMAIN_LOCAL DOMAIN_LOCAL destination static DOMAIN_REMOTE DOMAIN_REMOTE no-proxy-arp route-lookup
!
object network DMZ_Network
nat (DMZ,Outside) dynamic interface
object network DOMAIN_LOCAL
[code]....
I have a PIX 515E that I want to use to as a border between my internet connection and my Cisco AIR1131AG. I have configured the PIX to have the outside interface as a dhcp client which gets its dynamic IP address from the cable modem. the AP is connected to the E1 inside interface. Now I could see the E1 interface from the arp table from the AP but I cannot ping it. From the firewall I don't see the ARP table from the firewall. and i cannot ping the AP. what is wrong with the configuration? side note, i am able to connect to the AIR1131AG from my laptop I was not able to retrieve an IP address.
FW1 - CONFIGURATION
interface Ethernet0 description uplink towards the techsavvy modem speed 100 nameif outside security-level 0 ip address dhcp setroute !interface Ethernet1 description >>> WIFI LAN ACCESS <<< nameif inside security-level 100 ip address 10.0.0.1 255.255.255.0
[Code].....
Remote-access users aren't able to reach our remote network through a site-to-site VPN tunnel between two ASA 5505's.
I've seen several threads about that here, I've run through the walkthrough at [URL] I've taken a stab at setting split tunnelling and nat exemption, but it seems I'm still missing something. Remote-access users can reach the main site, but not the remote site.
Remote-access (vpn-houston) uses 192.168.69.0/24.
The main site (houston) uses 10.0.0.0/24
The remote site (lugoff) uses 10.0.1.0/24
We have a site-site and remote vpn configured in same interface in ASA 5520 ( software version 8.3 ). When Remote vpn users try to connect to computers located on the distant end of site-site VPN, their request failed. I tried No-Nat between remote vpn private IP to the remote site private IP, also stated the same in Split tunneling. I cant find even the tracert, ping also timed out.
View 7 Replies View RelatedI setup RA-VPN under local asa 5510 IP pool (192.168.127.0/24) and all was working fine. I got internet and local network access.
Then i have 5 site to site VPN working fine but when im traying to access to those L2L VPNs from the remote acces client im not able to do that. So after that i decided to obtain IP addresses from my DHCP server so i can obtain IPs from my local network (172.17.16.0/16) and then access normally to the VPN site to site. But the surprise was that the VPN cisco client is getting local IP address (172.17.16.222) perfectly but im not able to access even to my local network.
I have the same-security-traffic permit inter-interface same-security-traffic permit intra-interface enable.
I have a 2504 WLC and 1042 ap's. Everything worked great in my test enviroment (of course). Now when I want to deploy the wireless, the ap's are not getting and ip for the windows dhcp server.
I have option 43 configured in dhcp, sub option 241>ip address of the controller
I have my A record in dns, cisco-capwap-controller.
*Mar 1 00:03:17.050: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Not in Bound state.
*Mar 1 00:03:27.050: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:27.054: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:03:37.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:47.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:57.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:04:07.054: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
Not in Bound state.
How do i get the 12.4 code to assign a dhcp address to my ethernet interface from my server? I deleted the default config on the 1141 and searching has not turned up anything useful.
View 1 Replies View RelatedI have a Cisco 2911 router configured with a couple of VPN tunnels . The issue that I am having is that I cannot access the servers (WEB,EMIL) thru the tunnel . After looking around found out that adding a route-map to my static NAT rule will fix the issue . Once I do that I am able to access the serves thru the VPN but my local machines lose internet access .So I have to delete the access list The issue seems to be with the Access list 110 permit ip [code]
View 5 Replies View RelatedWe have a 5508 controller in main site.Which has two ports connected to local network.Management VLAN 500 is untagged and mapped to Port 1.All other interfaces are including 501 to 507 are mapped to Port 2.We have a SSID that is mapped to VLAN 501 interface , which successfully can be joined in main site.We connect an AP to remote site ;We have a remote site VLAN 115 which can be reached from main site.We connect an AP to access vlan 115 port on the remote site , we had described option 43 , so AP can successfully finds controller in local mode.
AP gets ip from VLAN 115 , can setup connection / ping controller successfully.There is a wide area connection between remote and main site.No trunk setup , the whole remote site is vlan 115.However when the client is trying to connect the test SSID , client cant get connected nor get ip address.Local switching is disabled.For this setup , client comes to AP as a requested , AP tunnels traffic to controller from vlan 500 , controller lets the client get into wired platform from VLAN 501.
setup a DHCP server on a WLC 2504. I'll try to resume my configuration:
I have 2 networks: inside users (vlan 1) and external users (vlan)
My controller uses the port 1 to connect to the switch, which has a trunk with WLC.
I have two routers, one using vlan 1 (192.168.3.0/24) and one using vlan 10 (200.X.X.X). All ports to these routers are access ports on their respective vlans.
I have 2 SSID, one for inside, other to outside. Inside is working very well.
To the outside I created a DHCP escope and already set the IP of the management interface 192.168.3.119.
Managemente interface (vlan 1 inside): 192.168.3.119/24
Outside interface (vlan 10): 200.X.X.195 - Default gateway 200.X.X.X.193
I alredy checked the DHCP Proxy in Advanced option.
See the output of the debug client:
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
[Code].....
I have an out of the box configured RV220W and was wondering if it supports local DNS resoltuion for DHCP addresses it issues. I have a few reservations and a custon search domain configured ('local') but it will not resolve a name fromt the terminal using the search domain (see below):
It resolves freenas but not freenas.local.
macbookair:~ brantwinter$ dig freenas
; <<>> DiG 9.8.1-P1 <<>> freenas
;; global options: +cmd
[Code]...
I currently have DCHP server set up on my new 1141N. Everything works great, but I wanted to know if it were possible to make the DHCP server only hand out ip addresses on the wireless connection? Currently the AP is giving out ip addresses from the pool to wired and wireless pc's.
View 3 Replies View RelatedI have a RVS4000 router with DHCP enabled and in router mode.
The LAN is 192.168.2.x. The RVS4000 static IP address is 192.168.2.8
The router is not the RVS4000 and is at 192.168.2.1
The RVS4000 dhcp is assigning it's clients a default gateway of 192.168.2.8 instead of what I want 192.168.2.1. How can I get the RVS4000's DHCP server to assign another IP address other than its own as the default gateway to its DHCP clients?
I have configured vpn filtering on all my l2l vpns. I have restricted access from remote to local resources only to specified ports. It works perfectly.But I want to have also full access from local to remote networks (but still preserve restricted access from remote to local). As I now VPN Filter works bi-directional with a single ACL. So is there some way to open all traffic from local to remote and still restrict remote to local traffic? ASA 5520 8.4(3)
View 4 Replies View RelatedSince the number of computers are expanding at my home, I want to reduce Wireless Connectivity and increase Ethernet connection between computers. I will be running a Server that supports 10 TB Storage.Will a Custom PC be better or should I use a NAS connected to a web server?
I currently use a Linksys WRT160n router that supports only 4 ethernet connections.Now I need at least 40 Ethernet connections. Will a Switch do? Also I will be running Asterisk to support Telephones.
My web server will not function globally. Only in LAN.And also, the web server will have a 250gb Wikipedia Dump that will deploy 10 times; and also a lot of video from KhanAcademy for knowledge base.I am looking for something powerful which will be quiet and have less downtime.I have checked out Newegg, eRacks, and many other websites. But I am confused with what to consider buying.
A Local Web Server or a custom built PC for 10tb hard drive suppoty.Router that can provide wired connection to about 40 users.A Terminal so I can monitor the bandwidth usage.
i have 5508 WLC and 1242 LAP . i 5508 connects to core switch and LAP connects to access switch, and there is L3 link from core swtich to access switch , so i have to use HREAP to let my WLC to control my APs.in my access switch i set ip helper-address to my WLC in the client vlam, then all the wireless clients cannot get ip address from the WLC.but if i set ip helper-address to another DHCP server , the wireless clients can get ip address .so i dont know why WLC cannot be the DHCP server of the wireless client?
View 3 Replies View RelatedI have a LAN with about 200 computers (192.168.10.0/24) with a DHCP Server on Windows server 2003.The problem is that my company have acquired 100 others computers that I have connected on this network.Some computer does not get IP address from the DHCP server. When I investigated the log of the DHCP server, I realized that the DHCP server was out of addresses.
View 2 Replies View RelatedWe have a Cisco 5505 ASA fireawll at a remote site. I can get the firewall to issue the IP addresses to the pc's, Is there a way for the pc's to get their IP addresses directly from our DHCP server?
View 3 Replies View RelatedI used to use a CentOS self-made server for intranet for my little office, but I bouth few days ago a Cisco 861 router to replace the linux box.
1. I have 2 public IP classes from my ISP. 1 class is limitted to 80mbit upload, the other to 30mbit upload. So I need some sort of DNAT to be able to know exactly which intranet computer uses big internet and which one limitted internet.
2. I need DHCP server and with static IP addresses (one computer must always have the same IP address, etc).. i have my needs for this.
3. Also I need external access to some servers inside (web, ftp, etc) [code]
So far so good, all looks simple and I can achieve this in 2 hours on a centos linux box (correct routes, ip forwarding enabled and few iptables rules for NAT/SNAT/DNAT).
But on this brand new Centos router well, i'm not even successful in pinging the outside world, nor the inside world I'm tired of reading the forums, the documentation..i want (at first) a simple scenario: vlan+dhcp, fa4 with 1 public ip address and ACCESS to the real world. I wasn't able to achieve not even that much. [code]
I have a Motorola Surfboard Modem connected to a Netgear 24-port switch. I bought the WAP4410N to provide wireless connectivity from the switch.
All my PC's can get perfect connectivity via the switch but none of my wireless devices can connect at all.
Sometimes I can get 1 PC to connect but what's strange is I can view my networked folders and such but cannot access the internet.
I've upgraded the firmware to the latest May-2012. IPv4 and IPv6 are both set to automatic.
When i connect VPN in server site then I can't use my Local Internet connection?
View 1 Replies View RelatedSetting up a stand-alone WDS/PXE server.Current we have helper addresses setup to forward the DHCP requests from the different VLAN's to the DHCP server. The WDS/PXE server we are setting up is on its server. How do we craft the helper addresses so DHCP requests go to the proper server hosting DHCP and PXE requests go the WDS server?
Everything I seen on Microsoft Technet, lists using Helper Address as the recommended way, but assume both services are on the same server. Our helper address is as follows on each VLAN interface in router: ip helper-address X.X.X..This is a Cisco 3750.
I am tasked with configuring a 2504 wireless controller. Is it possible to assign an SSID to an interface that has dynamic ap management enabled?
Scenario:
Location1:
1) 10.0.0.0/24
2)192.168.0.0/24 DMZ
Location 2:
1) 10.0.5.0
Both locations are routable using network 1 at each location. However, I need to configure several access points and send them to location 2. These access points will communicate with the controller at location 1 on network 1. Two SSIDs will need to be on network 1 at location 1. The other SSID will be on Network 2 at location 1. This network is not routable.
We have 2 nexus 7010 switches configured with HSRP in the network. For all the vlans core1 is Master and Core2 is standby. In the current setup we have external dhcp server and dhcp relay is configured for all the vlans on Master and standby switch. The setup is running the IOS 5.2
Activity Done: During the Maintainacne activity, we isolated core1 switch in the network by disabling the vpc/keepalive and all the uplinks from access switch. The core2 switch was master for all the vlans.
Issue observed: It has been observed that new users were not getting ip address from the dhcp server. The ethereal capture showed that dhcp server was not getting the dhcp requests from the core2 switch. We disabled the dhcp feature in core2 and enabled again with dhcp relay again configured on vlan interfaces .even after doing this no change was observed in behaviour. Finally we got core1 back in network by enabling all the links.
Observation: The moment VPC link came up between the core switches, users started getting ip's from dhcp. Then we started enabling all the uplinks on core1.Core1 again become master for all the vlans and users continued getting ip’s. Network running fine.
Further Testing
1. For one of the vlan, core 2 switch has been made primary and for new users checked the dhcp functionality and it was working fine. The aim was to identify if anything wrong on core 2 related to dhcp relay
2.Again we changed the priority for this vlan and made core1 master for the same. This time we disabled this vlan on core1 and tried new user with core 2 became master and dhcp functionality worked fine for new user. Actually in this case we have simulated the same behaviour when we observed the issue with only difference of VPC was not available during the issue time as core 1 was isolated form network
Inputs needed.
Is there any known behaviour for dhcp functionality when VPC is unavailable? If we see the test scenario2 (wherein core1 was master for the vlan and we disable this vlan on core 1 and core 2 was able to relay dhcp requests for new users in this vlan.) it was actually same as scenario we observed during issue time..
I ran into a very interesting problem that occurred today and I'm trying to figure out why it happened. If it was one ASA 5505 that just required the reboot, then I'd have just chalked it up to a glitch, but when we built a new AD/ DNS server on the main network at the main site and changed the 3 Remote site ASAs to point to the new DNS server in the DHCPD options, none of them could ping any local host names to the DNS server at the main site they were now pointing too, but external host names { URL} all translated and pinged fine.
From a laptop on one of the remote sites, we could ping the new AD/DNS server(192.168.0.3) and the old AD/DNS server(192.168.0.2) and everything else at the main site, and telnet to port 53 showed successful across the Easy VPN from the Remote site to the new server at the main site. When wire shark was added to the new DNS server at the main site, the DNS request and replies for {URL}, for example, came and worked fine, but any requests for local resources never made it to the server from the remote sites.
A reboot of one of the Remote Site ASA's corrected the issue. Then I rebooted the other two remote site ASAs, and now DNS was working fine for everybody. I had also tried clearing the ARP cache on the ASAs before resorting to rebooting them. I also tried rebooting the laptop thinking the local DNS cache needed cleared before resorting to rebooting the ASAs. I'm struggling to understand why external, public host names made it through and resolved from the remote sites to the new server at the main site, but anything local failed before even reaching the new server(The new DNS server could resolve requests made by computers at the main site, but the remote sites that traverse the Easy VPN from the ASAs failed). The new AD/DNS server is the only server configured for DNS for all remote site computers.
Is any of this making sense? I'm wondering if clearing the x late or local host tables would have corrected it without having to reboot. I'm just trying to grasp the understanding here and figure out what happened.
Haveing issue with DHCP server handing out IP addresses to client connected to VLAN5 interface.ISP Router>Firewall -(WatchGuard Drop-in mode) I have several 3750 switches and one acting as a L3 switch. The L3 is configured as follow: [code]
If I connect a laptop to int fa1/0/10 I DO NOT get an IP address from the 10.100.0.8 scope. If I connect to another interface within the VLAN 1, I get an address from the 10.100.0.0 range.
I am configuring remote access vpn on ASA5505.Everything is working fine so far, except when the client got connected, it still used the local DNS server provided by the ISP. How do I force the client to use the DNS server configured on ASA?
View 7 Replies View RelatedMy ISP recently started offering dual stack IPv6. After changing IPv6 from manual tunnel to automatic, none of my devices get an IPv6 address from the ISP. In the troubleshooting page, IPv6 address is also empty. I tried resetting the router but had no difference. We have another router (ASUS RT-53N) and it works fine.The ISP is using PPPoE for IPv4. In RT-53N I choose "IPv6 with DHCP-PD" and Interface "PPP". There're no such options in EA2700 though.
View 9 Replies View Related