The 1130ag was the LAP model but I upgraded it to run in autonomous mode. My understanding is that it cannot assign IP addresses but I just want that confirmed. It is not connected to a WLC nor a server that can do DHCP.
View 5 RepliesIs it possible to assign IP addresses to remote site WIFI users from local DHCP server and forward all other traffic to 2504 WLC?
[WIFI Users] >--------<AP (DHCP server) >------ VPN ---------< WLC
I imagine I can use the framed-ip-address attribute to assign ip-addresses but there seem to be support for static ip addresses only?A bit of a drag when we're talking 200+ nodes.
View 1 Replies View RelatedI upgraded my SG500 switch firmware to 1.3.0.59, since there is a new functionality DHCP server v.4 well I must say I came accross the issue I cannot solve. DHCP server assign dynamic address - no hassles. troubles start with static IP hosts.I defined a couple of hosts with static address within the correct subnet. I tried with hardware address and client identifiers. no luck. my switch does not assign the IP address I assigned to the suitable mac address. to define it I use both CLI & Web.
ip dhcp pool host HP-Elliteaddress 10.10.11.7 255.255.255.0 client-identifier 01:d8:d3:85:cf:09:72client-name HP-Ellitedefault-router 10.10.11.1exit
ip dhcp pool host VAIO-Zaddress 10.10.14.108 255.255.255.0 hardware-address 54:53:ed:1c:a1:46
default-router 10.10.14.1exit
I have a PIX 515E that I want to use to as a border between my internet connection and my Cisco AIR1131AG. I have configured the PIX to have the outside interface as a dhcp client which gets its dynamic IP address from the cable modem. the AP is connected to the E1 inside interface. Now I could see the E1 interface from the arp table from the AP but I cannot ping it. From the firewall I don't see the ARP table from the firewall. and i cannot ping the AP. what is wrong with the configuration? side note, i am able to connect to the AIR1131AG from my laptop I was not able to retrieve an IP address.
FW1 - CONFIGURATION
interface Ethernet0 description uplink towards the techsavvy modem speed 100 nameif outside security-level 0 ip address dhcp setroute !interface Ethernet1 description >>> WIFI LAN ACCESS <<< nameif inside security-level 100 ip address 10.0.0.1 255.255.255.0
[Code].....
I am trying to find a way to login to our wirless access point. I have a Aironet 1130AG series wireless router. I have the ip address. It is a POE device so i dont have a power supply for this device. When it is on I can see the Wireless Network but the passcode has been lost and no one knows it. Is there a default IP address for this equipment? There is an Ethernet port for a console but without the power supply i cannot access it.
View 3 Replies View RelatedHow can I enter into "interface configuration" on Aironet 1130AG, AIR-LAP1042N?When I put following commands in enable conf tinterface Dot11Radio1 but, it fails and I cannot enter into "interface configuration".How can I do this ?The reason why I enter into conf tinterface Dot11Radio1 because I want to disable cdp via CLI ( serial console).
View 9 Replies View RelatedI have installed an Aironet 1130AG and utilized a power injector for the power source. I have the settings configured correctly in IOS, but the AP takes about 7 minutes to come on (illuminate LED status lights) once the Ethernet cable is connected. Is this 7 minute power-on delay normal when using POE? I am used to the instanteous "on" that usually comes with Cisco products being connected directly to the AC adapter.
View 5 Replies View RelatedWith this customer they have 4 floors with on each floor a Cisco Aironet 1130AG. At the moment they are using WEP as a protection with a really long key. The users find this annoying, but I am more concerned about the security perspective. So I want to implement WPA2 with a shorter key for the people to remember. On one floor, I also want to add a public network when other people want to connect and just need internet access. How to change the current set-up and regarding the security and implementation. If all of the Access Points could work togheter and just be 1 wireless network. I don't know if this is possible and how to do it? For the public network I know there also need to be some changes in VLAN's. The firewall is a cisco ASA5505.
At the moment I am running this configuration: I tried setting up this with the GUI, but it doesn't look like the configuration at the moment is shown in the GUI or maybe I am just looking in the wrong places. [code]
I have a Motorola Surfboard Modem connected to a Netgear 24-port switch. I bought the WAP4410N to provide wireless connectivity from the switch.
All my PC's can get perfect connectivity via the switch but none of my wireless devices can connect at all.
Sometimes I can get 1 PC to connect but what's strange is I can view my networked folders and such but cannot access the internet.
I've upgraded the firmware to the latest May-2012. IPv4 and IPv6 are both set to automatic.
How would I configure a "guest" wireless network, with a different key/password, that uses a different subnet than the existing network?
We have a simple 192.168.1.x subnet currently, with the Aironet as our only AP. The Aironet support a "guest" wireless function, but how do I make that work with the RV180?
My ISP recently started offering dual stack IPv6. After changing IPv6 from manual tunnel to automatic, none of my devices get an IPv6 address from the ISP. In the troubleshooting page, IPv6 address is also empty. I tried resetting the router but had no difference. We have another router (ASUS RT-53N) and it works fine.The ISP is using PPPoE for IPv4. In RT-53N I choose "IPv6 with DHCP-PD" and Interface "PPP". There're no such options in EA2700 though.
View 9 Replies View Relatedhow do i assign IP addresses to 10 computers in a network?
View 3 Replies View RelatedI just thought if it's possible to make sure that only approved IP addresses for each of divisions of a company can be used.How can I assign for a port one/more public addresses and be sure that only this port is using it/them. Thing is I have only one 24 bit public Network ID provided to me by ISP. One IP address of the range is used for ISP's gateway. So I have 253 addresses to be distributed among divisions. However to avoid IP address conflicts I have to be sure that only dedicated for a division IP address/es is/are used by the division.
Router is 2821.
Switch is 2950.
I'm currently replacing my ASA 5505 with a 5510. I have a range of public IP addresses, one has been assigned to the outside interface by the setup wizard (e.g. 123.123.123.124 ) and another I would like to NAT to an internal server (e.g 192.168.0.3 > 123.123.123.125). On my asa 5505 this seemed fairly straigh forward, i.e. create an incoming access rule that allowed SMTP to 123.123.123.125 and then create a static nat to translate 192.168.0.3 to 123.123.123.125. Since I've tried to do the same on the 5510 traffic is not passing through so I'm assuming that the use of additional public IP addresses is not handled in the same way as the 5505? I also see that by default on the 5505, 2 VLANs are created, one for the inside and one for the outside, where as this is not the case on the 5510. Is the problem that VLANs or sub-interfaces need to be created first? I'm doing the config via ASDM.
Everything else seems to OK i.e. access to ASDM via 123.123.123.124, outbound PAT and the site-to-site VPN.
How do i tell my firewall to start listen also on another outside ipadress assigned by my ISP? I have it used on other firewall right now. So my steps would be shutting down ip address assignment off old firewall interface. Assign that ip address to ASA5510 outside interface and configure NAT.
View 13 Replies View RelatedI have a Motorola Surfboard Modem connected to a Netgear 24-port switch. I bought the WAP4410N to provide wireless connectivity from the switch. All my PC's can get perfect connectivity via the switch but none of my wireless devices can connect at all. Sometimes I can get 1 PC to connect but what's strange is I can view my networked folders and such but cannot access the internet. I've upgraded the firmware to the latest May-2012. IPv4 and IPv6 are both set to automatic.
View 1 Replies View RelatedI am studying for my CCENT and have two Cisco switches and three Cisco routers. I have 'configured' the switches and routers but how to obtain valid IP addresses to assign to my devices and how I can connect these devices to the internet via my wireless home hub.
View 3 Replies View RelatedI have a Belkin Play N600 HD router. Does it have the capability to let me assign fixed IP addresses to devices like printers, NAS drives, and cameras so I know where they are?
View 2 Replies View RelatedOur company is a small one and steadily growing towards mid size. We currently have about 200 or so users. Naturally we have run out of IP addresses and now we must redesign the entire IP schema.Initially our plan was to just implement a class B subnet for the whole network with certain ranges belonging to certain kinds of devices/machines/servers.Are there any cons to this? If so, could you link me to documentation that explains this?
View 4 Replies View RelatedHow do i get the 12.4 code to assign a dhcp address to my ethernet interface from my server? I deleted the default config on the 1141 and searching has not turned up anything useful.
View 1 Replies View RelatedCould I use DHCP for wireless connection and assign private IP for PC for wire connection ?Will it conflict to each other ?
View 3 Replies View RelatedInitially there were 3 SSIDs configured but all of them were assigned a single interface and this interface was configured with the controller management IP address as DHCP server so that the WLC could assign IP addresses to wireless clients, guns and printers etc.
Issue: As part of PCI initiative, we decided to segment the traffic in multiple subnets based on type of wireless clients; so now there are 3 interfaces configured and each SSID is assigned a specific dynamic interface and each interface is configured to use the controller management IP address as DHCP server.
There are 3 scopes configured for each of the dynamic interfaces/SSIDs and DHCP proxy is enabled but wirelss clients are still being allocated IP addresses from the original DHCP scope that was associated with the dynamic interface originally assigned to all 3 SSIDs.
I verified the following:
1. Each SSID is assigned a different dynamic interface (Users, Voice and Handhelds)
2. Each dynamic interface is configured to use controllers management IP address as DHCP server
3. DHCP scopes configured with correct network information for each dynamic interface and enabled
I have a LAP1142N that is connected to a 3560 nonPoE switch (using compatible power injector) that will not associate to the controller I have set-up. The wireless is existing and I have about 11 other APs connected to the controller with no issues. The AP will pull an IP address from DHCP running on the primary controller. The AP pulls a new IP address in roughly a minute. I set the pool to be 3 IP addresses and set a contant ping to each, there is about 1 request time out before the next IP address starts pinging. I went to the controller and pulled the following message error from the log.
*Feb 13 14:24:58.614: %LWAPP-3-HDR_ENCAP_ERR: spam_lrad.c:4216 Unable to encapsulate LWAPP header for discovery response; AP (APs MAC address)
*Feb 13 14:24:58.614: %APF-3-PDU_ENCAP_FAILED: apf_net.c:771 Failed to encapsulate a PDU for transmission to station00:00:00:00:00:00. Destination IP address not set in L3 mode.
I have tried a different cable, connecting to a PoE switch, different controller, larger DHCP range, hosting DHCP on the distribution switch, I am awaiting console access to the AP since this is remote work. The controller is running Software Version 5.1.151.0. Thoughts?
console inventory output from GUI
Model No. AIR-WLC4402-25-K9
Burned-in MAC Address XXXXXXXXXX
Maximum number of APs supported 25
Gig Ethernet/Fiber Card Absent
[Code] ....
Have a WLC 5508 running 7.0.230 with internal DHCP server. Timeout is 3600 seconds. The IP addresses never seem to be released. The controller will show 70 clients but 254 addresses will be assigned.
View 2 Replies View RelatedWe have 6 aironet 1140's throughout the office I have them all configed as one ssid but I would like the DHCP to come from our Windows server. Right now I have set them up with ip dhcp pools. So what is the secret to get them to send dhcp requests to the Windows server?
View 3 Replies View RelatedI have to configure DHCP on Aironet 1100 WAP so wireless client will get IP address through WAP. I tried all the option mentioned in Document but nothing is working.
View 1 Replies View RelatedWe have 12 - AP-1231G access points in our warehouse with 2 SSID's, both on different VLAN's. We would like to set one of the VLAN/SSID 's to use DHCP from a windows DHCP server.Is this possible to do with option 43 or is that only for lightweight AP's ? Sho ver: Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(8).
View 2 Replies View RelatedON ASA, I understand that we can assign a static IP for a specific VPN client, or we can use a DHCP pool to assign IP. Now if I want to create DHCP pools, say pool_A and pool_B, for user A, B and C they use the IP from Pool_A, and user D, E, and F they get the IP from pool_B. Is there a way to do this in ASA?
View 4 Replies View RelatedI currently have DCHP server set up on my new 1141N. Everything works great, but I wanted to know if it were possible to make the DHCP server only hand out ip addresses on the wireless connection? Currently the AP is giving out ip addresses from the pool to wired and wireless pc's.
View 3 Replies View RelatedEnvironment:
1. Core switch - Catalyst 6509e
vlans configured:
a. vlan 50 (wired clients)
[Code]....
here's the problem, wireless clients connected to WLAN guest keep getting DHCP leases from WLAN local 10.0.50.10 (scope 10.0.70.101 to 200)
Here at HQ we have a 4402 WLC. At our remote sites we have 1231G APs running in autonomous mode. I upgraded one of the APs -- IOS 12.4(3g)JA -- to run LWAPP. Per release notes I've read upgraded 1231's do not support REAP/HREAP mode, consequently, it's running in LOCAL mode.
The AP is managed by the WLC. I created a WLAN for the remote site and assigned it to the MGMT interface; the remote site subnet doesn't exist in HQ. The DHCP server for the remote site is presently at that site; AP and DHCP server reside at the same place.
Clients authenticate successfully to the remote site AP, however, they are not getting DHCP addresses assigned. Does the DHCP server for the remote site have to reside in HQ since the AP is running in local mode? If so, where is that specified, on the MGMT interface config?
Is it possible to NAT source & destination addresses (twice nat) on an ASA5520 running 7.2(5)?
View 4 Replies View Related