Cisco Wireless :: LAP1142N Cycling IP Addresses From DHCP
Feb 12, 2013
I have a LAP1142N that is connected to a 3560 nonPoE switch (using compatible power injector) that will not associate to the controller I have set-up. The wireless is existing and I have about 11 other APs connected to the controller with no issues. The AP will pull an IP address from DHCP running on the primary controller. The AP pulls a new IP address in roughly a minute. I set the pool to be 3 IP addresses and set a contant ping to each, there is about 1 request time out before the next IP address starts pinging. I went to the controller and pulled the following message error from the log.
*Feb 13 14:24:58.614: %LWAPP-3-HDR_ENCAP_ERR: spam_lrad.c:4216 Unable to encapsulate LWAPP header for discovery response; AP (APs MAC address)
*Feb 13 14:24:58.614: %APF-3-PDU_ENCAP_FAILED: apf_net.c:771 Failed to encapsulate a PDU for transmission to station00:00:00:00:00:00. Destination IP address not set in L3 mode.
I have tried a different cable, connecting to a PoE switch, different controller, larger DHCP range, hosting DHCP on the distribution switch, I am awaiting console access to the AP since this is remote work. The controller is running Software Version 5.1.151.0. Thoughts?
console inventory output from GUI
Model No. AIR-WLC4402-25-K9
Burned-in MAC Address XXXXXXXXXX
Maximum number of APs supported 25
Gig Ethernet/Fiber Card Absent
[Code] ....
I have 19 locations, each with 1 or more LAP1142N AP's in FlexConnect mode, AP's are primed using CAPWAP to my 5508 WLC at the datacenter. The AP's join the WLC without issue every time. I have two WLAN's, one guest and one staff, the guest network is open and obtains DHCP from a WatchGuard XTM33 firewall at each of the remote locations. The staff side is WPA2/RADIUS and DHCP is assigned from the WLC. Each AP is assigned a static IP that is not in the DHCP scope. For example: DHCP scope on the branch firewall is 192.168.1.10-250 the AP will be assigned static IP of 192.168.1.1.. The AP's are connected to a HP procurve switch that has a untagged VLAN, the firewall is using the native vlan 1 and so is the AP.
I have been running this network for over a year and it has not had a single issue until the last two weeks. Nothing on the network has changed or has been upgraded.The issue I am seeing is that clients are no longer able to connect to the AP and do not get DHCP assigned to them. I am able to get it working, if I remove the static IP from the AP, the AP will reboot, join the controller, then begin working, users can connect and DHCP is assigned from the firewall as it should. However, If the AP then reboots, the AP will join back to the controller but no clients can connect nor do they get a DHCP address. So, I then reassign a static IP to the AP again and it reboots, connects to the controller and clients then can connect and get DHCP.i've found several posts on this topic, in fact the patch of unassigning or reassigning static IP is one that I found. I am also waiting on my SmartNet to start up and will be contacting Cisco support as well.
Initially there were 3 SSIDs configured but all of them were assigned a single interface and this interface was configured with the controller management IP address as DHCP server so that the WLC could assign IP addresses to wireless clients, guns and printers etc.
Issue: As part of PCI initiative, we decided to segment the traffic in multiple subnets based on type of wireless clients; so now there are 3 interfaces configured and each SSID is assigned a specific dynamic interface and each interface is configured to use the controller management IP address as DHCP server.
There are 3 scopes configured for each of the dynamic interfaces/SSIDs and DHCP proxy is enabled but wirelss clients are still being allocated IP addresses from the original DHCP scope that was associated with the dynamic interface originally assigned to all 3 SSIDs.
I verified the following:
1. Each SSID is assigned a different dynamic interface (Users, Voice and Handhelds)
2. Each dynamic interface is configured to use controllers management IP address as DHCP server
3. DHCP scopes configured with correct network information for each dynamic interface and enabled
Have a WLC 5508 running 7.0.230 with internal DHCP server. Timeout is 3600 seconds. The IP addresses never seem to be released. The controller will show 70 clients but 254 addresses will be assigned.
The 1130ag was the LAP model but I upgraded it to run in autonomous mode. My understanding is that it cannot assign IP addresses but I just want that confirmed. It is not connected to a WLC nor a server that can do DHCP.
I currently have DCHP server set up on my new 1141N. Everything works great, but I wanted to know if it were possible to make the DHCP server only hand out ip addresses on the wireless connection? Currently the AP is giving out ip addresses from the pool to wired and wireless pc's.
Here at HQ we have a 4402 WLC. At our remote sites we have 1231G APs running in autonomous mode. I upgraded one of the APs -- IOS 12.4(3g)JA -- to run LWAPP. Per release notes I've read upgraded 1231's do not support REAP/HREAP mode, consequently, it's running in LOCAL mode.
The AP is managed by the WLC. I created a WLAN for the remote site and assigned it to the MGMT interface; the remote site subnet doesn't exist in HQ. The DHCP server for the remote site is presently at that site; AP and DHCP server reside at the same place.
Clients authenticate successfully to the remote site AP, however, they are not getting DHCP addresses assigned. Does the DHCP server for the remote site have to reside in HQ since the AP is running in local mode? If so, where is that specified, on the MGMT interface config?
I'd like to add a name to a few ip addresses in the DHCP client table currently there is an asterix for a couple client names. the router is an ea3500.
I have my other XBOXs connected to a 24 port switch but the one connected to the ea6500 directly gives me this moderate NAT issue. I thought this new router would be an upgrade to my old dlink but so far I get a new problem every day.I have reserved dhcp addresses for all the boxes and set up port triggering for the ports listed in several guides. But what else do I need to do? Is it likely I got a bad router?
Region : Poland Model : TL-WDR4300 Hardware Version : V1 Firmware Version : 3.13.23 Build 120810 Rel.44064n ISP : [url]...
I'm having issues with DHCP server not dealing IP after few hours (varies between 1h and 8h) of torrent traffic. If no continuous torrent traffic is applied, the problem does not occur. New wireless devices connect to the wi-fi network, but get stuck on 'getting IP adress'. The problem is with DHCP service or the wireless network service. New wired devices receive IP. The problem is only with wireless devices. I have no additional wireless device, that I can configure the network settings on my own (only phones) to check if it works without DHCP server giving IP. Wired connection is stable, but the bandwidth usage curve becomes somewhat similar to a sinewave.
I did disable the hardware NAT because that feature made the router unstable and caused it to hang up within minutes.
I've just installed a 2106 Controller at a remote site. The Controller is seen by the WCS at the main site so, connectivity is good and I'm able to login from the main site. I've configured the DHCP server which is at the Main site on the AP manager interface and the Manager interface and on the WLAN of the new controller but, APs are not getting addresses.
I've created a tonne of dhcp scopes on my routers before never had any issues, however this one will not hand out any addresses at all, i even give the router a reload to see if any magic happened but nothing, ive ended having to put a temp server in with just dhcp installed until i get the router diong what it should my config below, its something simple i havent seen, as ive compared it to plenty of my working DHCP configs and seen nothing.
I've had a WRT54GL ( for about a week now ) with no real issues. Today my wife mentioned that the net's been flaky ( wireless nto hard wired ). I originally noticed what seemed like minutes for my desktop of laptop to connect to any web pages. Loads were extremely slow. According to the computer I had a 1 mbps connection. I did the standard resetting of the modem and router.babble babble babble. Eventually, I ran a wifi analyzer from my phone to determine an ideal channel. However, while running the frequency scanner I also noticed that my broadcasting would continue to drop off the radar for a quick moment then return. This seemed to be true no matter what channel I set. What's interesting is that the signal would read as extremely strong for 45 sec - 1 minute, then completely drop the signal, then another strong broadcast. Other neighboring signals don't exhibit this behavior....well I would see the weaker signals coming in and off the radar from time to time. I'm guessing it's some type of interference? However if that's the case I can't explain why my signal seems so strong. I'm assuming I'd see a lot of fluctuation in my signal before dropping off ( instead of going from 100 to 0 in the blink of an eye ).
How can i configure DHCP to use two different range of IP addresses. One range will be for example 192.168.0.* and the other range will be 192.168.1.* When the first range of ip is full the DHCP automatically assign IP addresses from the second range.
After the upgrade of the WLC 5508 to version 7.4 the 1142 access-points LED blinking rapidly cycling through blue, green, and red. I found the following information to this behavior: "Access point location command invoked"
The configuration didn't change. How can I switch this function?
I recently upgraded a clients WLC and they keep saying they are unable to get an IP address from the DHCP server. It's a simple, flat network and here is what the logs are showing.
*apfReceiveTask: Apr 11 13:37:25.477: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty. *apfReceiveTask: Apr 11 13:37:17.278: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty. *apfReceiveTask: Apr 11 13:37:05.880: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty. *apfReceiveTask: Apr 11 13:13:47.397: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
I currently have a the following configuration and am unable to get more than 2 DHCP addresses for the devices connected to the Cisco new SG 100-16 Switch.The AP have no trouble handing out DHCP to the wireless clients, but we are unable to get the SG 100-16 to be able to do the same thing to wired clients. It is currently connected to the 2960-8 in port 1. We can get 2 devices connected without a problem, but the 3rd machine and beyond do not work. Also, setting up a static IP does not work. Using a static will not even allow us to ping or tracer back to any devices beyond the SG 100-16.
Netgear DG834 allocates IP Addresses using DHCP to 5 computers and 2 tills, the tills addresses and one computer IP addreess are reserved and fixed, so that data can be downloaded from the tills to this computer. However I had to re-format the computer and the Router now allocates a new IP address to it, which the tills cannot recognise, so I cannot download the data from the tills to the computer. Is it possible to change the newly allocated Computer IP address in the Router back to the old one.
I have a Belkin model F9K1102 router supplying WAN/LAN connection to three PCs and 2 laptops. Two of the PCs are hardwired with the remainder PC and laptops are wireless. I'm using the default router IP of 192.168.2.1 and my ISP is Charter Cable (if that's of significance). The router is picking up all the dynamic IP information from my ISP and internal DHCP is enabled. Here's the issue though - when I connect a PC, laptop or iTouch (wired or wireless) with obtain IP settings automatically enabled the IP address it receives an IP address on a different subnet ie, 192.168.3.x and thus won't have WAN/LAN connection. I have tried to set the router IP to 192.168.3.1 and set the scope in the .3 subnet but the IP obtained by the device is .4! This makes no sense to me at all. The router is on the latest firmware (according to Belkin) and there doesn't seem to be any other update I can find. I have also tried another Belkin router (older model: F5D8236) and it does the same thing.
I'm not sure if this is related but I upgraded my service with Charter to a 18MB connection and a D3.0 Ubee cable modem - this issue seem to have began after this upgrade but I don't see how that would have any bearing on what is happening on my LAN IP scope and Charter tech support is pretty useless. My workaround is that I've static assigned an IP for each device in the same subnet as the router but it would be nice for the DHCP to function correctly.
I imagine I can use the framed-ip-address attribute to assign ip-addresses but there seem to be support for static ip addresses only?A bit of a drag when we're talking 200+ nodes.
I have a wireless access point, I want to be able to hand out addresses via the Cisco router through DHCP on the interface eth0/1. The wireless users that get an IP I want then route out the eth0/0 interface to my statically assigned default gateway. Right now Im not concerned with setting up security measures once this works I'll go back in and add that. Here is my running-config. Right now nothing from the 10.0.0.0 is being routed out to the internet.
I have a LAN with about 200 computers (192.168.10.0/24) with a DHCP Server on Windows server 2003.The problem is that my company have acquired 100 others computers that I have connected on this network.Some computer does not get IP address from the DHCP server. When I investigated the log of the DHCP server, I realized that the DHCP server was out of addresses.
We have a Cisco 5505 ASA fireawll at a remote site. I can get the firewall to issue the IP addresses to the pc's, Is there a way for the pc's to get their IP addresses directly from our DHCP server?
I used to use a CentOS self-made server for intranet for my little office, but I bouth few days ago a Cisco 861 router to replace the linux box.
1. I have 2 public IP classes from my ISP. 1 class is limitted to 80mbit upload, the other to 30mbit upload. So I need some sort of DNAT to be able to know exactly which intranet computer uses big internet and which one limitted internet. 2. I need DHCP server and with static IP addresses (one computer must always have the same IP address, etc).. i have my needs for this. 3. Also I need external access to some servers inside (web, ftp, etc) [code]
So far so good, all looks simple and I can achieve this in 2 hours on a centos linux box (correct routes, ip forwarding enabled and few iptables rules for NAT/SNAT/DNAT).
But on this brand new Centos router well, i'm not even successful in pinging the outside world, nor the inside world I'm tired of reading the forums, the documentation..i want (at first) a simple scenario: vlan+dhcp, fa4 with 1 public ip address and ACCESS to the real world. I wasn't able to achieve not even that much. [code]
Had a problem with a 3750 this morning not handing out DHCP addresses. The following is a sanitized config of what the switch is using. [code] The IOS installed on the switch is c3750-ipbasek9-mz.122-55.SE1.bin. What got my attention was that the sh ip dhcp pool PC showed 180 addresses being excluded. In doing the math from the dhcp excluded addresses, only 64 should be excluded.
My next step was to remove the second dhcp excluded-address line above. Doing a clear ip dhcp binding * started letting the DHCP service hand out addresses but the sh ip dhcp pool PC stil showed 180 addresses excluded.
It finally took removing the dhcp pool and putting it back in to drop the number of excluded addresses down to a value that matches the first excluded-address line. Didnt see a dhcp bug in the bug database that would explain this.
I tried re-entering the second excluded-address line from above and saw the number of excluded addresses rise as expected. When I negated the line, the number of excluded addresses dropped back to its previous value.
A small network and uses the Linksys Router BEFSR81 as dhcp.the default Number of addresses is 50 and starts 10.0.0.100 to 10.0.0.149.A new Cisco IP Phone just introduced requires ip addresses and have noticed running out of addreses.Can I increase the number to 120 so that the address range would start from 10.0.0.100 to 10.0.0.219, also, I have a VPN device which automatically configures itself for 10.0.0.199 address and this is /24 network configuration.
I have an out of the box configured RV220W and was wondering if it supports local DNS resoltuion for DHCP addresses it issues. I have a few reservations and a custon search domain configured ('local') but it will not resolve a name fromt the terminal using the search domain (see below):
It resolves freenas but not freenas.local. macbookair:~ brantwinter$ dig freenas ; <<>> DiG 9.8.1-P1 <<>> freenas ;; global options: +cmd [Code]...
i have to Bridge the AP to VLAN1 which has the DHCP pool. For some reason when I try to do this from iOS console it tells me that gig0 is not a bridgable interface. I am newb to Cisco iOS (24 hours new ). I got the Cisco Configuration Professional working and would like to fix my issue through there if possible? why my AP wont get anything but APIPA addresses?
version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption
I upgraded my SG500 switch firmware to 1.3.0.59, since there is a new functionality DHCP server v.4 well I must say I came accross the issue I cannot solve. DHCP server assign dynamic address - no hassles. troubles start with static IP hosts.I defined a couple of hosts with static address within the correct subnet. I tried with hardware address and client identifiers. no luck. my switch does not assign the IP address I assigned to the suitable mac address. to define it I use both CLI & Web.
ip dhcp pool host HP-Elliteaddress 10.10.11.7 255.255.255.0 client-identifier 01:d8:d3:85:cf:09:72client-name HP-Ellitedefault-router 10.10.11.1exit ip dhcp pool host VAIO-Zaddress 10.10.14.108 255.255.255.0 hardware-address 54:53:ed:1c:a1:46 default-router 10.10.14.1exit
I am trying to setup my 3550 layer 3 switch to do hand out dhcp addresses for different vlans. It is connected to my router address 192.168.1.1. I setup a new vlan 3 and the dhcp pool.. The client gets a 192.168.3.2 address but am not able to ping the router and other clients and get out to the internet.
Here is the config that I have. I deleted the other ports because I am not using them. The vlan 3 client is on port fast Ethernet 0/17 and the router is connected to the fastethernet 0/1.
version 12.2 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption
I have a PIX 515E that I want to use to as a border between my internet connection and my Cisco AIR1131AG. I have configured the PIX to have the outside interface as a dhcp client which gets its dynamic IP address from the cable modem. the AP is connected to the E1 inside interface. Now I could see the E1 interface from the arp table from the AP but I cannot ping it. From the firewall I don't see the ARP table from the firewall. and i cannot ping the AP. what is wrong with the configuration? side note, i am able to connect to the AIR1131AG from my laptop I was not able to retrieve an IP address.
FW1 - CONFIGURATION
interface Ethernet0 description uplink towards the techsavvy modem speed 100 nameif outside security-level 0 ip address dhcp setroute !interface Ethernet1 description >>> WIFI LAN ACCESS <<< nameif inside security-level 100 ip address 10.0.0.1 255.255.255.0
