Cisco :: 2106 - APs Not Getting DHCP Addresses?

May 25, 2011

I've just installed a 2106 Controller at a remote site. The Controller is seen by the WCS at the main site so, connectivity is good and I'm able to login from the main site. I've configured the DHCP server which is at the Main site on the AP manager interface and the Manager interface and on the WLAN of the new controller but, APs are not getting addresses.

View 6 Replies


ADVERTISEMENT

Cisco :: DHCP Scope Not Handing Out Addresses

May 21, 2012

I've created a tonne of dhcp scopes on my routers before never had any issues, however this one will not hand out any addresses at all, i even give the router a reload to see if any magic happened but nothing, ive ended having to put a temp server in with just dhcp installed until i get the router diong what it should my config below, its something simple i havent seen, as ive compared it to plenty of my working DHCP configs and seen nothing.

View 11 Replies View Related

Configure DHCP To Use Two Different Range Of IP Addresses?

Sep 5, 2011

How can i configure DHCP to use two different range of IP addresses. One range will be for example 192.168.0.* and the other range will be 192.168.1.* When the first range of ip is full the DHCP automatically assign IP addresses from the second range.

View 9 Replies View Related

Cisco Wireless :: WLC 7.0.230.0 - Incorrect DHCP Addresses Being Allocated?

May 13, 2012

Initially there were 3 SSIDs configured but all of them were assigned a single interface and this interface was configured with the controller management IP address as DHCP server so that the WLC could assign IP addresses to wireless clients, guns and printers etc.
 
Issue: As part of PCI initiative, we decided to segment the traffic in multiple subnets based on type of wireless clients; so now there are 3 interfaces configured and each SSID is assigned a specific dynamic interface and each interface is configured to use the controller management IP address as DHCP server.
 
There are 3 scopes configured for each of the dynamic interfaces/SSIDs and DHCP proxy is enabled but wirelss clients are still being allocated IP addresses from the original DHCP scope that was associated with the dynamic interface originally assigned to all 3 SSIDs.
 
I verified the following:
 
1. Each SSID is assigned a different dynamic interface (Users, Voice and Handhelds)

2. Each dynamic interface is configured to use controllers management IP address as DHCP server

3. DHCP scopes configured with correct network information for each dynamic interface and enabled

View 2 Replies View Related

Cisco :: WLC2412 - Clients Not Receiving DHCP Addresses?

Apr 10, 2012

I recently upgraded a clients WLC and they keep saying they are unable to get an IP address from the DHCP server.  It's a simple, flat network and here is what the logs are showing. 
 
*apfReceiveTask: Apr 11 13:37:25.477: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
*apfReceiveTask: Apr 11 13:37:17.278: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
*apfReceiveTask: Apr 11 13:37:05.880: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.
*apfReceiveTask: Apr 11 13:13:47.397: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'management'. Marking interface dirty.

[code]....

View 19 Replies View Related

Cisco Wireless :: LAP1142N Cycling IP Addresses From DHCP

Feb 12, 2013

I have a LAP1142N that is connected to a 3560 nonPoE switch (using compatible power injector) that will not associate to the controller I have set-up. The wireless is existing and I have about 11 other APs connected to the controller with no issues. The AP will pull an IP address from DHCP running on the primary controller. The AP pulls a new IP address in roughly a minute. I set the pool to be 3 IP addresses and set a contant ping to each, there is about 1 request time out before the next IP address starts pinging. I went to the controller and pulled the following message error from the log.

*Feb 13 14:24:58.614: %LWAPP-3-HDR_ENCAP_ERR: spam_lrad.c:4216 Unable to encapsulate LWAPP header for discovery response; AP (APs MAC address)
*Feb 13 14:24:58.614: %APF-3-PDU_ENCAP_FAILED: apf_net.c:771 Failed to encapsulate a PDU for transmission to station00:00:00:00:00:00. Destination IP address not set in L3 mode.
 
I have tried a different cable, connecting to a PoE switch, different controller, larger DHCP range, hosting DHCP on the distribution switch, I am awaiting console access to the AP since this is remote work. The controller is running Software Version 5.1.151.0. Thoughts?
 
console inventory output from GUI
 
Model No. AIR-WLC4402-25-K9
Burned-in MAC Address XXXXXXXXXX
Maximum number of APs supported 25
Gig Ethernet/Fiber Card Absent
[Code] ....

View 2 Replies View Related

Cisco Wireless :: 5508 WLC Not Releasing DHCP Addresses?

May 1, 2013

Have a WLC 5508 running 7.0.230 with internal DHCP server. Timeout is 3600 seconds. The IP addresses never seem to be released. The controller will show 70 clients but 254 addresses will be assigned.

View 2 Replies View Related

Cisco Switching/Routing :: SG 100-16 Switch - 2 DHCP Addresses

Jan 11, 2012

I currently have a the following configuration and am unable to get more than 2 DHCP addresses for the devices connected to the Cisco new SG 100-16 Switch.The AP have no trouble handing out DHCP to the wireless clients, but we are unable to get the SG 100-16 to be able to do the same thing to wired clients.  It is currently connected to the 2960-8 in port 1.  We can get 2 devices connected without a problem, but the 3rd machine and beyond do not work.  Also, setting up a static IP does not work.  Using a static will not even allow us to ping or tracer back to any devices beyond the SG 100-16.

View 7 Replies View Related

DG834 Allocates IP Addresses Using DHCP To 5 Computers

Oct 6, 2011

Netgear DG834 allocates IP Addresses using DHCP to 5 computers and 2 tills, the tills addresses and one computer IP addreess are reserved and fixed, so that data can be downloaded from the tills to this computer. However I had to re-format the computer and the Router now allocates a new IP address to it, which the tills cannot recognise, so I cannot download the data from the tills to the computer. Is it possible to change the newly allocated Computer IP address in the Router back to the old one.

View 9 Replies View Related

Router DHCP Handing Out IP Addresses Not On The Same Subnet?

Dec 22, 2011

I have a Belkin model F9K1102 router supplying WAN/LAN connection to three PCs and 2 laptops. Two of the PCs are hardwired with the remainder PC and laptops are wireless. I'm using the default router IP of 192.168.2.1 and my ISP is Charter Cable (if that's of significance). The router is picking up all the dynamic IP information from my ISP and internal DHCP is enabled. Here's the issue though - when I connect a PC, laptop or iTouch (wired or wireless) with obtain IP settings automatically enabled the IP address it receives an IP address on a different subnet ie, 192.168.3.x and thus won't have WAN/LAN connection. I have tried to set the router IP to 192.168.3.1 and set the scope in the .3 subnet but the IP obtained by the device is .4! This makes no sense to me at all. The router is on the latest firmware (according to Belkin) and there doesn't seem to be any other update I can find. I have also tried another Belkin router (older model: F5D8236) and it does the same thing.

I'm not sure if this is related but I upgraded my service with Charter to a 18MB connection and a D3.0 Ubee cable modem - this issue seem to have began after this upgrade but I don't see how that would have any bearing on what is happening on my LAN IP scope and Charter tech support is pretty useless. My workaround is that I've static assigned an IP for each device in the same subnet as the router but it would be nice for the DHCP to function correctly.

View 7 Replies View Related

AAA/Identity/Nac :: ACS 5.3 - Assign Ip Addresses From A DHCP Server?

Dec 8, 2011

I imagine I can use the framed-ip-address attribute to assign ip-addresses but there seem to be support for static ip addresses only?A bit of a drag when we're talking 200+ nodes.

View 1 Replies View Related

Cisco 2611 Router - Enable To Hand Out Addresses Through DHCP

Oct 4, 2012

I have a wireless access point, I want to be able to hand out addresses via the Cisco router through DHCP on the interface eth0/1. The wireless users that get an IP I want then route out the eth0/0 interface to my statically assigned default gateway. Right now Im not concerned with setting up security measures once this works I'll go back in and add that. Here is my running-config. Right now nothing from the 10.0.0.0 is being routed out to the internet.

View 6 Replies View Related

Cisco :: DHCP Server No Longer Handing Out IP Addresses On Network?

Jun 16, 2012

I have a LAN with about 200 computers (192.168.10.0/24) with a DHCP Server on Windows server 2003.The problem is that my company have acquired 100 others computers that I have connected on this network.Some computer does not get IP address from the DHCP server. When I investigated the log of the DHCP server, I realized that the DHCP server was out of addresses.

View 2 Replies View Related

Cisco Firewall :: ASA5505 / Pcs To Get Their IP Addresses Directly From DHCP Server?

Feb 7, 2012

We have a Cisco 5505 ASA fireawll at a remote site. I can get the firewall to issue the IP addresses to the pc's, Is there a way for the pc's to get their IP addresses directly from our DHCP server?

View 3 Replies View Related

Cisco Switching/Routing :: 861 Need DHCP Server With Static IP Addresses

Feb 2, 2013

I used to use a CentOS self-made server for intranet for my little office, but I bouth few days ago a Cisco 861 router to replace the linux box.
 
1. I have 2 public IP classes from my ISP. 1 class is limitted to 80mbit upload, the other to 30mbit upload. So I need some sort of DNAT to be able to know exactly which intranet computer uses big internet and which one limitted internet.
2. I need DHCP server and with static IP addresses (one computer must always have the same IP address, etc).. i have my needs for this.
3. Also I need external access to some servers inside (web, ftp, etc) [code]
 
So far so good, all looks simple and I can achieve this in 2 hours on a centos linux box (correct routes, ip forwarding enabled and few iptables rules for NAT/SNAT/DNAT).
 
But on this brand new Centos router well, i'm not even successful in pinging the outside world, nor the inside world I'm tired of reading the forums, the documentation..i want (at first) a simple scenario: vlan+dhcp, fa4 with 1 public ip address and ACCESS to the real world. I wasn't able to achieve not even that much. [code]

View 6 Replies View Related

Cisco Switching/Routing :: 3750 Not Handing Out DHCP Addresses

Nov 2, 2011

Had a problem with a 3750 this morning not handing out DHCP addresses.  The following is a sanitized config of what the switch is using. [code] The IOS installed on the switch is c3750-ipbasek9-mz.122-55.SE1.bin.  What got my attention was that the sh ip dhcp pool PC showed 180 addresses being excluded.  In doing the math from the dhcp excluded addresses, only 64 should be excluded.
 
My next step was to remove the second dhcp excluded-address line above.  Doing a clear ip dhcp binding * started letting the DHCP service hand out addresses but the sh ip dhcp pool PC stil showed 180 addresses excluded.
 
It finally took removing the dhcp pool and putting it back in to drop the number of excluded addresses down to a value that matches the first excluded-address line.  Didnt see a dhcp bug in the bug database that would explain this.
 
I tried re-entering the second excluded-address line from above and saw the number of excluded addresses rise as expected.  When I negated the line, the number of excluded addresses dropped back to its previous value.

View 1 Replies View Related

Increasing Number Of Addresses And Dhcp Address Range

Dec 2, 2011

A small network and uses the Linksys Router BEFSR81 as dhcp.the default Number of addresses is 50 and starts 10.0.0.100 to 10.0.0.149.A new Cisco IP Phone just introduced requires ip addresses and have noticed running out of addreses.Can I increase the number to 120 so that the address range would start from 10.0.0.100 to 10.0.0.219, also, I have a VPN device which automatically configures itself for 10.0.0.199 address and this is /24 network configuration.

View 1 Replies View Related

Cisco Wireless :: Can Aironet 1130ag Assign IP Addresses Through DHCP Running

Jan 20, 2010

The 1130ag was the LAP model but I upgraded it to run in autonomous mode.  My understanding is that it cannot assign IP addresses but I just want that confirmed.  It is not connected to a WLC nor a server that can do DHCP.

View 5 Replies View Related

Cisco Wireless :: 1141N To Make DHCP Server Only Hand Out IP Addresses

Sep 28, 2010

I currently have DCHP server set up on my new 1141N. Everything works great, but I wanted to know if it were possible to make the DHCP server only hand out ip addresses on the wireless connection? Currently the AP is giving out ip addresses from the pool to wired and wireless pc's.

View 3 Replies View Related

Cisco Wireless :: Catalyst 6509e - Clients Not Getting Correct Dhcp Addresses

Sep 9, 2012

Environment:
1. Core switch - Catalyst 6509e
vlans configured:
a. vlan 50 (wired clients)

[Code]....

here's the problem, wireless clients connected to WLAN guest keep getting DHCP leases from WLAN local 10.0.50.10 (scope 10.0.70.101 to 200)

View 11 Replies View Related

Cisco Wireless :: Clients Authenticating To 1231G Not Getting Assigned DHCP Addresses

Jun 24, 2007

Here at HQ we have a 4402 WLC. At our remote sites we have 1231G APs running in autonomous mode. I upgraded one of the APs -- IOS 12.4(3g)JA -- to run LWAPP. Per release notes I've read upgraded 1231's do not support REAP/HREAP mode, consequently, it's running in LOCAL mode.
 
The AP is managed by the WLC. I created a WLAN for the remote site and assigned it to the MGMT interface; the remote site subnet doesn't exist in HQ. The DHCP server for the remote site is presently at that site; AP and DHCP server reside at the same place.
 
Clients authenticate successfully to the remote site AP, however, they are not getting DHCP addresses assigned.  Does the DHCP server for the remote site have to reside in HQ since the AP is running in local mode? If so, where is that specified, on the MGMT interface config?

View 4 Replies View Related

Cisco Routers :: RV220W Supports Local Name Resolution For DHCP Addresses

Sep 17, 2012

I have an out of the box configured RV220W and was wondering if it supports local DNS resoltuion for DHCP addresses it issues. I have a few reservations and a custon search domain configured ('local') but it will not resolve a name fromt the terminal using the search domain (see below):
 
It resolves freenas but not freenas.local.
macbookair:~ brantwinter$ dig freenas
 ; <<>> DiG 9.8.1-P1 <<>> freenas
;; global options: +cmd
[Code]...

View 3 Replies View Related

Cisco Switching/Routing :: 881w-gn-a-k9 Access Point Not Serving DHCP Addresses

Jan 27, 2013

i have to Bridge the AP to VLAN1 which has the DHCP pool. For some reason when I try to do this from iOS console it tells me that gig0 is not a bridgable interface. I am newb to Cisco iOS (24 hours new ). I got the Cisco Configuration Professional working and would like to fix my issue through there if possible? why my AP wont get anything but APIPA addresses?

version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption

[code]....

View 13 Replies View Related

Cisco Switches :: SG500 DHCP Server Does Not Assign Predefined Static IP Addresses

May 17, 2013

I upgraded my SG500 switch firmware to 1.3.0.59, since there is a new functionality DHCP server v.4 well I must say I came accross the issue I cannot solve. DHCP server assign dynamic address - no hassles. troubles start with static IP hosts.I defined a couple of hosts with static address within the correct subnet. I tried with hardware address and client identifiers. no luck. my switch does not assign the IP address I assigned to the suitable mac address. to define it I use both CLI & Web.

ip dhcp pool host HP-Elliteaddress 10.10.11.7 255.255.255.0 client-identifier 01:d8:d3:85:cf:09:72client-name HP-Ellitedefault-router 10.10.11.1exit
ip dhcp pool host VAIO-Zaddress 10.10.14.108 255.255.255.0 hardware-address 54:53:ed:1c:a1:46
default-router 10.10.14.1exit

View 16 Replies View Related

Cisco WAN :: Setup 3550 Layer 3 Switch To Do Hand Out Dhcp Addresses For Different Vlans?

Dec 26, 2012

I am trying to setup my 3550 layer 3 switch to do hand out dhcp addresses for different vlans.  It is connected to my router address 192.168.1.1.  I setup a new vlan 3 and the dhcp pool.. The client gets a 192.168.3.2 address but am not able to ping the router and other clients and get out to the internet. 

Here is the config that I have.  I deleted the other ports because I am not using them.  The vlan 3 client is on port fast Ethernet 0/17 and the router is connected to the fastethernet 0/1. 

version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption

[code]....

View 12 Replies View Related

Cisco Firewall :: Pix 515E Cannot Ping Or Assign DHCP Addresses To Inside Clients

May 6, 2011

I have a PIX 515E that I want to use to as a border between my internet connection and my Cisco AIR1131AG.  I have configured the PIX to have the outside interface as a dhcp client which gets its dynamic IP address from the cable modem. the AP is connected to the E1 inside interface. Now I could see the E1 interface from the arp table from the AP but I cannot ping it. From the firewall I don't see the ARP  table  from the firewall. and i cannot ping the AP. what is wrong with the configuration? side note, i am able to connect to the AIR1131AG from my laptop I was not able to retrieve an IP address. 
 
FW1 - CONFIGURATION
 
interface Ethernet0 description uplink towards the techsavvy modem speed 100 nameif outside security-level 0 ip address dhcp setroute !interface Ethernet1 description >>> WIFI LAN ACCESS <<< nameif inside security-level 100 ip address 10.0.0.1 255.255.255.0

[Code].....

View 3 Replies View Related

Linksys Wireless Router :: Ea3500 - Add Name To Few Ip Addresses In DHCP Client Table?

May 20, 2012

I'd like to add a name to a few ip addresses in the DHCP client table currently there is an asterix for a couple client names. the router is an ea3500. 

View 2 Replies View Related

Linksys Wireless Router :: Ea6500 Reserved Dhcp Addresses For All The Boxes

Sep 28, 2012

I have my other XBOXs connected to a 24 port switch but the one connected to the ea6500 directly gives me this moderate NAT issue. I thought this new router would be an upgrade to my old dlink but so far I get a new problem every day.I have reserved dhcp addresses for all the boxes and set up port triggering for the ports listed in several guides. But what else do I need to do? Is it likely I got a bad router?

View 2 Replies View Related

Belkin Routers :: F5D8236-4 V2 - DHCP Client List Is Not Showing All IP Addresses In Use

Feb 23, 2013

I have a Wireless N router model F5D8236-4 v2 (01) with firmware 2.00.04 (Nov 12 2008 10:51:08) and it's not showing all issued wireless or Wired IP addresses in DHCP Client List.

They all have IP addresses and connect to the internet through the router, but in the router administration page, they're not listing. The Windows devices all show but most of the Mac devices are not, nor is my XBox 360.

My reason for investigating this is because the router seems to keep losing the Mac devices and a router reboot fixes it, but it shouldn't have this problem because all the Windows devices just seem to work.

According to the support page I have the latest available (dated November 12, 2008 which really seems kinda old to me for a Wireless N router). Are there any plans for a new firmware offering for this modem or have you already deprecated it as "legacy equipment"?

View 1 Replies View Related

3750 - Craft Helper Addresses So DHCP Requests Go To Proper Server

Dec 15, 2012

Setting up a stand-alone WDS/PXE server.Current we have helper addresses setup to forward the DHCP requests from the different VLAN's to the DHCP server. The WDS/PXE server we are setting up is on its server. How do we craft the helper addresses so DHCP requests go to the proper server hosting DHCP and PXE requests go the WDS server?

Everything I seen on Microsoft Technet, lists using Helper Address as the recommended way, but assume both services are on the same server. Our helper address is as follows on each VLAN interface in router: ip helper-address X.X.X..This is a Cisco 3750.

View 6 Replies View Related

TP-Link Dual-Band Wireless :: TL-WDR4300 - DHCP Not Dealing Addresses After Few Hours?

Dec 9, 2012

Region : Poland
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : [url]...

I'm having issues with DHCP server not dealing IP after few hours (varies between 1h and 8h) of torrent traffic. If no continuous torrent traffic is applied, the problem does not occur. New wireless devices connect to the wi-fi network, but get stuck on 'getting IP adress'. The problem is with DHCP service or the wireless network service. New wired devices receive IP. The problem is only with wireless devices. I have no additional wireless device, that I can configure the network settings on my own (only phones) to check if it works without DHCP server giving IP. Wired connection is stable, but the bandwidth usage curve becomes somewhat similar to a sinewave.

I did disable the hardware NAT because that feature made the router unstable and caused it to hang up within minutes.

View 7 Replies View Related

Cisco Wireless :: 2504 / Assign IP Addresses To Remote Site Wi-Fi Users From Local DHCP Server?

May 29, 2012

Is it possible to assign IP addresses to remote site WIFI users from local DHCP server and forward all other traffic to 2504 WLC?
 
[WIFI Users] >--------<AP (DHCP server) >------ VPN ---------< WLC

View 1 Replies View Related

Cisco Switching/Routing :: 3750 DHCP Server Handing Out IP Addresses To Client Connected To VLAN5 Interface

Feb 23, 2012

Haveing issue with DHCP server handing out IP addresses to client connected to VLAN5 interface.ISP Router>Firewall -(WatchGuard Drop-in mode) I have several 3750 switches and  one acting as a L3 switch. The L3 is configured as follow: [code]
 
If I connect a laptop to int fa1/0/10 I DO NOT get an IP address from the 10.100.0.8 scope. If I connect to another interface within the VLAN 1, I get an address from the 10.100.0.0 range.

View 7 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved