Cisco Switching/Routing :: 3750 DHCP Server Handing Out IP Addresses To Client Connected To VLAN5 Interface
Feb 23, 2012
Haveing issue with DHCP server handing out IP addresses to client connected to VLAN5 interface.ISP Router>Firewall -(WatchGuard Drop-in mode) I have several 3750 switches and one acting as a L3 switch. The L3 is configured as follow: [code]
If I connect a laptop to int fa1/0/10 I DO NOT get an IP address from the 10.100.0.8 scope. If I connect to another interface within the VLAN 1, I get an address from the 10.100.0.0 range.
View 7 Replies
ADVERTISEMENT
Nov 2, 2011
Had a problem with a 3750 this morning not handing out DHCP addresses. The following is a sanitized config of what the switch is using. [code] The IOS installed on the switch is c3750-ipbasek9-mz.122-55.SE1.bin. What got my attention was that the sh ip dhcp pool PC showed 180 addresses being excluded. In doing the math from the dhcp excluded addresses, only 64 should be excluded.
My next step was to remove the second dhcp excluded-address line above. Doing a clear ip dhcp binding * started letting the DHCP service hand out addresses but the sh ip dhcp pool PC stil showed 180 addresses excluded.
It finally took removing the dhcp pool and putting it back in to drop the number of excluded addresses down to a value that matches the first excluded-address line. Didnt see a dhcp bug in the bug database that would explain this.
I tried re-entering the second excluded-address line from above and saw the number of excluded addresses rise as expected. When I negated the line, the number of excluded addresses dropped back to its previous value.
View 1 Replies
View Related
Jan 10, 2013
We have a 3750 running IOS ver 12.2 (44) SE, it has performed great and we have never had a problem with it. However we have noticed that when we had an outage some of our Wireless APs didn't come up as they get DHCP from the 3750. The DHCP scope said IP was depleted although there were IPs to give. We had to delete and recreate the DHCP Pool. However two days later we got the same problem and then had to do the same thing over again.
View 8 Replies
View Related
Jun 16, 2012
I have a LAN with about 200 computers (192.168.10.0/24) with a DHCP Server on Windows server 2003.The problem is that my company have acquired 100 others computers that I have connected on this network.Some computer does not get IP address from the DHCP server. When I investigated the log of the DHCP server, I realized that the DHCP server was out of addresses.
View 2 Replies
View Related
Apr 17, 2013
I have a DHCP server for a subnet that has only lightweight WAP's in it. The DHCP server is running on the gateway for this subnet which is a 3750X 2 switch stack running 12.2(53r)se2.I have the following configured:
ip dhcp excluded-address 10.1.10.161 10.1.10.162
ip dhcp pool DHCP-VL20
network 10.1.10.160 255.255.255.224
domain-name mydomain.net
dns-server 10.11.11.30 10.11.11.40
default-router 10.1.10.161
ease 3
The server hands out up to 18 IP addresses and no more, with 20 devices on the subnet. Scanning the subnet with a 3rd party network management system I see the following IP's never get handed out or used:
10.1.10.161 - 162 (manually excluded)
10.1.10.167 - 168
10.1.10.171 - 176
10.1.10.178
and of course 2 IP's I have manually excluded, 11 IP's in all that wont get handed out. It should only be 2 that don't get handed out. I've double and triple checked the exclusion and thats the only one. so I run a 'sh ip dhcp pool' and see this:
Pool DHCP-VL20 :
Utilization mark (high/low) : 100 / 0
Subnet size (first/next) : 0 / 0
Total addresses : 30
[code]....
[edit]I should also mention that "sh ip dhcp bind" does not show these randomly excluded IP's in use. They also do not show up in any arp table I can find.I have looked all over the config and I cant find where these extra 9 addresses are being excluded. how to free up these 9 seemingly random exclusions? Haven't issued a reload and I haven't deleted and rebuilt the DHCP server yet, production network.
View 2 Replies
View Related
May 21, 2012
I've created a tonne of dhcp scopes on my routers before never had any issues, however this one will not hand out any addresses at all, i even give the router a reload to see if any magic happened but nothing, ive ended having to put a temp server in with just dhcp installed until i get the router diong what it should my config below, its something simple i havent seen, as ive compared it to plenty of my working DHCP configs and seen nothing.
View 11 Replies
View Related
Dec 22, 2011
I have a Belkin model F9K1102 router supplying WAN/LAN connection to three PCs and 2 laptops. Two of the PCs are hardwired with the remainder PC and laptops are wireless. I'm using the default router IP of 192.168.2.1 and my ISP is Charter Cable (if that's of significance). The router is picking up all the dynamic IP information from my ISP and internal DHCP is enabled. Here's the issue though - when I connect a PC, laptop or iTouch (wired or wireless) with obtain IP settings automatically enabled the IP address it receives an IP address on a different subnet ie, 192.168.3.x and thus won't have WAN/LAN connection. I have tried to set the router IP to 192.168.3.1 and set the scope in the .3 subnet but the IP obtained by the device is .4! This makes no sense to me at all. The router is on the latest firmware (according to Belkin) and there doesn't seem to be any other update I can find. I have also tried another Belkin router (older model: F5D8236) and it does the same thing.
I'm not sure if this is related but I upgraded my service with Charter to a 18MB connection and a D3.0 Ubee cable modem - this issue seem to have began after this upgrade but I don't see how that would have any bearing on what is happening on my LAN IP scope and Charter tech support is pretty useless. My workaround is that I've static assigned an IP for each device in the same subnet as the router but it would be nice for the DHCP to function correctly.
View 7 Replies
View Related
Apr 3, 2012
Have a client wanting to hand out public ip addresses to all clients from a PFSense Firewall terminating the internet connection.
How do I allow the Cisco Switches currently in place, configured with private ip addresses in the 10.10.x.x ranges and Vlans, where the main 3550 layer 3 has defined dhcp scopes for each vlan, to relay dhcp requests from all vlans to the PFSense firewall?
I assume I would take off the currently defined dhcp scopes for the vlans and configure each vlan/switch with the ip helper address and specify the PFSense firewall and that Nat would have to be disabled onthe firewall?
View 1 Replies
View Related
Feb 2, 2013
I used to use a CentOS self-made server for intranet for my little office, but I bouth few days ago a Cisco 861 router to replace the linux box.
1. I have 2 public IP classes from my ISP. 1 class is limitted to 80mbit upload, the other to 30mbit upload. So I need some sort of DNAT to be able to know exactly which intranet computer uses big internet and which one limitted internet.
2. I need DHCP server and with static IP addresses (one computer must always have the same IP address, etc).. i have my needs for this.
3. Also I need external access to some servers inside (web, ftp, etc) [code]
So far so good, all looks simple and I can achieve this in 2 hours on a centos linux box (correct routes, ip forwarding enabled and few iptables rules for NAT/SNAT/DNAT).
But on this brand new Centos router well, i'm not even successful in pinging the outside world, nor the inside world I'm tired of reading the forums, the documentation..i want (at first) a simple scenario: vlan+dhcp, fa4 with 1 public ip address and ACCESS to the real world. I wasn't able to achieve not even that much. [code]
View 6 Replies
View Related
Dec 15, 2012
Setting up a stand-alone WDS/PXE server.Current we have helper addresses setup to forward the DHCP requests from the different VLAN's to the DHCP server. The WDS/PXE server we are setting up is on its server. How do we craft the helper addresses so DHCP requests go to the proper server hosting DHCP and PXE requests go the WDS server?
Everything I seen on Microsoft Technet, lists using Helper Address as the recommended way, but assume both services are on the same server. Our helper address is as follows on each VLAN interface in router: ip helper-address X.X.X..This is a Cisco 3750.
View 6 Replies
View Related
May 28, 2013
I have customer who has as Core Switch one Cisco Catalyst 3750 with the IOS c3750-ipbase-mz.122-35.SE5.I know that this image support DHCP Server configuration, but I like to implementate new vlans (approx 15) and I want to know if this switch support 15 DHCP Servers.
View 3 Replies
View Related
Dec 11, 2012
a new LAN installation, two VSS pair 6509 core, 15 closets, with 3750 stacks. Floor 15 only, devices/hosts can ping teh DHCP server but cannot aquire IP addresses. no such problem on other floors?
portfast an dother parameters are intact.
View 2 Replies
View Related
Jul 30, 2012
How to configure cisco 3560 to force the client only can get ip by dhcp-relay server ?
The company i am working in has 5 vlans which have been set an lay-3 switch(3560), uses the dhcp-relay server .(in svi configuration: ip helper-address X.X.X.X) well , that works ok~
Now , I got my problem: I need to force the client only can get ip by dhcp-relay server, that means if anyone set static IP manunally , he can't really access to anywhere (to provent anyone set static IP with malignancy )
I know if a h3c router , how to set this configuration n svi configuration : dhcp relay security address-check enable )
the how to configure on a cisco 3560 ?
View 1 Replies
View Related
May 7, 2013
I am trying to configure interface vlan1 to get an ip address from dhcp by entering the commnad ip address dhcp ios rejects the dhcp portion of my command as not recognised although it is referred to in Cisco manuals.my IOS version is c2950-i6k2l2q4-mz.121-22.EA14.bin.I get the same problem when I try to configure ip http secure-server on the switch. Is this a known bug or whether I have the correct IOS version for these commands?
View 6 Replies
View Related
Aug 1, 2012
We have Dell M6220 blade server that server is connected to cisco 3750 switch. I am trying to configure LACP in 3750 for two port which are connected to Dell M6220 server switch. The channel-group 2 mode active commande is not taking then its showing the error protocol mismatch and if i run show int port-channel 2 command the port channel status is showing down. The Dell server switch is on simple mode. below i have attached the required details.
Switch#show int port-channel 2
Port-channel2 is down, line protocol is down (notconnect)
Hardware is EtherChannel, address is 0000.0000.0000 (bia 0000.0000.0000)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
[code]...
View 2 Replies
View Related
Jun 12, 2013
I Lease fiber between two locations, My operator limiting number of MAC addresses to 8 macs. Is there any possibility using some feature available in the Cisco 3750 switches to (hide mac addresses) encapsulate traffic witch flowing via operator network ?
I need to send data between locations with 1Gb/s speed. If 3750 switches can't do that, which models of switches 1 or 2U can do it. May Metro switches ?
View 1 Replies
View Related
Feb 16, 2012
I have Catalyst 3750 running IOS version c3750-ipservicesk9-mz.122-55.SE.bin. I have an access port that connects to a Redhat Linux version 5.4 64 bits machine. When I perform a "show mac address-table interface g1/0/3" where the redhat machine is connected to, I see two mac addresses on this access port. One of the mac addresses, 0025.9006.4898, belongs the the redhat machine. the other mac address, I have no idea where it comes from. I tried to perform clear mac address-table dynamic g1/0/3 several times but it does not work either.
View 8 Replies
View Related
Jan 11, 2012
I currently have a the following configuration and am unable to get more than 2 DHCP addresses for the devices connected to the Cisco new SG 100-16 Switch.The AP have no trouble handing out DHCP to the wireless clients, but we are unable to get the SG 100-16 to be able to do the same thing to wired clients. It is currently connected to the 2960-8 in port 1. We can get 2 devices connected without a problem, but the 3rd machine and beyond do not work. Also, setting up a static IP does not work. Using a static will not even allow us to ping or tracer back to any devices beyond the SG 100-16.
View 7 Replies
View Related
Feb 21, 2012
we have a 3750 and use dhcp services on the switch. every so often we run out of ip's even though we have much less users than the size of the allocated dhcp pool. I've noticed that the dhcp bind table is full but a ping-sweep only shows very few ip's being assinged and used. It looks like the IP addresses are not being released from the table even though I have decreased the lease time to 8 hours.
View 2 Replies
View Related
Jan 27, 2013
i have to Bridge the AP to VLAN1 which has the DHCP pool. For some reason when I try to do this from iOS console it tells me that gig0 is not a bridgable interface. I am newb to Cisco iOS (24 hours new ). I got the Cisco Configuration Professional working and would like to fix my issue through there if possible? why my AP wont get anything but APIPA addresses?
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
View 13 Replies
View Related
May 20, 2012
I'd like to add a name to a few ip addresses in the DHCP client table currently there is an asterix for a couple client names. the router is an ea3500.
View 2 Replies
View Related
Feb 23, 2013
I have a Wireless N router model F5D8236-4 v2 (01) with firmware 2.00.04 (Nov 12 2008 10:51:08) and it's not showing all issued wireless or Wired IP addresses in DHCP Client List.
They all have IP addresses and connect to the internet through the router, but in the router administration page, they're not listing. The Windows devices all show but most of the Mac devices are not, nor is my XBox 360.
My reason for investigating this is because the router seems to keep losing the Mac devices and a router reboot fixes it, but it shouldn't have this problem because all the Windows devices just seem to work.
According to the support page I have the latest available (dated November 12, 2008 which really seems kinda old to me for a Wireless N router). Are there any plans for a new firmware offering for this modem or have you already deprecated it as "legacy equipment"?
View 1 Replies
View Related
Dec 8, 2011
I imagine I can use the framed-ip-address attribute to assign ip-addresses but there seem to be support for static ip addresses only?A bit of a drag when we're talking 200+ nodes.
View 1 Replies
View Related
Feb 7, 2012
We have a Cisco 5505 ASA fireawll at a remote site. I can get the firewall to issue the IP addresses to the pc's, Is there a way for the pc's to get their IP addresses directly from our DHCP server?
View 3 Replies
View Related
Sep 28, 2010
I currently have DCHP server set up on my new 1141N. Everything works great, but I wanted to know if it were possible to make the DHCP server only hand out ip addresses on the wireless connection? Currently the AP is giving out ip addresses from the pool to wired and wireless pc's.
View 3 Replies
View Related
Apr 16, 2013
We are configuring ACLs for a dhcp pool on Sw3750
ip access-list extended Test
permit ip any 192.168.1.0 0.0.0.31
permit ip any host 172.16.1.1
And, here is dhcp pool:
ip dhcp excluded 192.168.1.1 192.168.1.3
ip dhcp pool Name
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
But when a PC try to obtain IP automatically, it doesn't work.
View 3 Replies
View Related
May 13, 2012
i created the 10 V LAN in my Cisco 3750 switch.All other V LAN DHCP IP's (192.168.2.X - 192.168.10.X) will be release from the DHCP server except VLAN1 . In my 3750 switch i created DHCP pool(192.168.14.X).... and i assigned to VLAN10.... but one of the client is assigned to V LAN 2(192.168.2.X) configuration. but its getting IP from the Cisco DHCP instead of DHCP server.
View 2 Replies
View Related
May 23, 2013
I need to configure public and private wireless access using an ASA 5505 and an Aironet AIR-AP1041N-A-K9. I need to be able to do this via ASDM and http if at all possible. I simply do not have the time to learn hundreds of lines of arcane CLI code. The Aironet connects to the ASA successfully, and receives an IP. I can then connect to the AP wirelessly, but do not receive an IP. I have setup a second SSIDVLAN on the AP, and can't connect to it at all.
View 4 Replies
View Related
May 17, 2012
I can ping [URL], from the router but not from a client attached to the router dhcp interface(10.1.3.1). When I turn on ip routing I cannot ping at all. Here is the config I have now that can ping the internet from the router.
sh runBuilding configuration... Current configuration : 1191 bytes!! No configuration change since last restart!version 12.3no service timestamps debug uptimeservice timestamps log datetime msecno service password-encryption!hostname
[code]....
View 7 Replies
View Related
Sep 29, 2011
i am facing the same problem now but am using windows 2003 server
View 1 Replies
View Related
May 17, 2013
I upgraded my SG500 switch firmware to 1.3.0.59, since there is a new functionality DHCP server v.4 well I must say I came accross the issue I cannot solve. DHCP server assign dynamic address - no hassles. troubles start with static IP hosts.I defined a couple of hosts with static address within the correct subnet. I tried with hardware address and client identifiers. no luck. my switch does not assign the IP address I assigned to the suitable mac address. to define it I use both CLI & Web.
ip dhcp pool host HP-Elliteaddress 10.10.11.7 255.255.255.0 client-identifier 01:d8:d3:85:cf:09:72client-name HP-Ellitedefault-router 10.10.11.1exit
ip dhcp pool host VAIO-Zaddress 10.10.14.108 255.255.255.0 hardware-address 54:53:ed:1c:a1:46
default-router 10.10.14.1exit
View 16 Replies
View Related
Jul 16, 2012
I want to clear following things regarding Cisco 3750 switch.
1. Can I configure Multiple DHCP pool on C3750?
2. Performance effect due to same?
3. Can I resrve IP addrese from DHCP pool for specific MAC address.
4. Can I Exempt IP address from DHCP pool ?
View 5 Replies
View Related
Apr 9, 2013
How to configure hsrp in my client location.They have 1 no of router and 2 no of 3750 switch.they need to configure Hsrp in switch.
View 5 Replies
View Related
