Cisco Switching/Routing :: 3750 IP Addresses Are Not Being Released From Table
Feb 21, 2012
we have a 3750 and use dhcp services on the switch. every so often we run out of ip's even though we have much less users than the size of the allocated dhcp pool. I've noticed that the dhcp bind table is full but a ping-sweep only shows very few ip's being assinged and used. It looks like the IP addresses are not being released from the table even though I have decreased the lease time to 8 hours.
View 2 Replies
ADVERTISEMENT
Jan 18, 2012
I have one VLAN on a 3750 where I do not see any MAC addresses even though it is in use. This is an unrouted VLAN between a WLC on a port- channel /LAG and an access port to an ASA for guest traffic. When I do a show MAC add I get nothing for VLAN 60 (guest DMZ) but all other VLANs seem to be OK. Spanning tree is not showing TC counters incrementing either.
I also was told when put a port on this VLAN the laptop did not get a DHCP address form the ASA, but the wireless guest clients are working fine. I can see the DHCP leases and ARP entries in the ASA and the ASA ARP in the WLC so some traffic is passing fine. I'm not onsite right now so troubleshooting is all remote which limits some options.
View 4 Replies
View Related
Jun 27, 2012
I am looking for a way to create different routing policies for vlans on a 3750 table.
My set up is
Clients----------- 3750 -------------- ASA ---------------Servers
|
|
|
Internet Routers
What i am trying to do is on the 3750 to route private networks to my ASA on different subintefaces and all internet to my internet routers . Each VLAN has a different GW for the internet. On some case i have the ASA as a default gateway. ASA default default route is 3750 where i need the internet traffic to be spllited on the proper Boarder router.
View 1 Replies
View Related
Jan 10, 2013
We have a 3750 running IOS ver 12.2 (44) SE, it has performed great and we have never had a problem with it. However we have noticed that when we had an outage some of our Wireless APs didn't come up as they get DHCP from the 3750. The DHCP scope said IP was depleted although there were IPs to give. We had to delete and recreate the DHCP Pool. However two days later we got the same problem and then had to do the same thing over again.
View 8 Replies
View Related
Jun 12, 2013
I Lease fiber between two locations, My operator limiting number of MAC addresses to 8 macs. Is there any possibility using some feature available in the Cisco 3750 switches to (hide mac addresses) encapsulate traffic witch flowing via operator network ?
I need to send data between locations with 1Gb/s speed. If 3750 switches can't do that, which models of switches 1 or 2U can do it. May Metro switches ?
View 1 Replies
View Related
Feb 16, 2012
I have Catalyst 3750 running IOS version c3750-ipservicesk9-mz.122-55.SE.bin. I have an access port that connects to a Redhat Linux version 5.4 64 bits machine. When I perform a "show mac address-table interface g1/0/3" where the redhat machine is connected to, I see two mac addresses on this access port. One of the mac addresses, 0025.9006.4898, belongs the the redhat machine. the other mac address, I have no idea where it comes from. I tried to perform clear mac address-table dynamic g1/0/3 several times but it does not work either.
View 8 Replies
View Related
Oct 8, 2012
In setup for old RV042 (V1), when updating / adding Mac addresses, the table is always sorted by IP addresses. But in the new oneRV042 (V3) I have, even with latest firmware 4.2.1.02 the list is random, thereby increasing the chance of user entering DUPLICATE IP addr with diff Mac addr. That will result in conflict.If the firmware sorts the DHCP entries by ip addresses, user would be able to catch duplicate ip errors even if the system does not flag the errors. All Cisco smart engineers can you all get the dhcp entries SORT by ip addresses.
View 2 Replies
View Related
Nov 2, 2011
Had a problem with a 3750 this morning not handing out DHCP addresses. The following is a sanitized config of what the switch is using. [code] The IOS installed on the switch is c3750-ipbasek9-mz.122-55.SE1.bin. What got my attention was that the sh ip dhcp pool PC showed 180 addresses being excluded. In doing the math from the dhcp excluded addresses, only 64 should be excluded.
My next step was to remove the second dhcp excluded-address line above. Doing a clear ip dhcp binding * started letting the DHCP service hand out addresses but the sh ip dhcp pool PC stil showed 180 addresses excluded.
It finally took removing the dhcp pool and putting it back in to drop the number of excluded addresses down to a value that matches the first excluded-address line. Didnt see a dhcp bug in the bug database that would explain this.
I tried re-entering the second excluded-address line from above and saw the number of excluded addresses rise as expected. When I negated the line, the number of excluded addresses dropped back to its previous value.
View 1 Replies
View Related
Feb 23, 2012
Haveing issue with DHCP server handing out IP addresses to client connected to VLAN5 interface.ISP Router>Firewall -(WatchGuard Drop-in mode) I have several 3750 switches and one acting as a L3 switch. The L3 is configured as follow: [code]
If I connect a laptop to int fa1/0/10 I DO NOT get an IP address from the 10.100.0.8 scope. If I connect to another interface within the VLAN 1, I get an address from the 10.100.0.0 range.
View 7 Replies
View Related
Dec 20, 2012
Do you know why there are two MAC addresses in iPad's interface table? Only the first digit is changed from a 4 to a 6. MAC address sites recognize one and not the other. I am trying to figure out if I have been networked into a neighbor's security/surveillance system and thus mapping out what is linking to what. I am using IT tools app as well as searching many websites.
View 2 Replies
View Related
Apr 6, 2011
We have an issue in which some of our public IPs will not work from outside. We have a couple of subnets/29. We allow traffic via access rules and they point to internal servers (nat to nat). So I requested an ARP table from our ISP router. The table shows that the non working IPs have a differect MAC address than the working IPs. Our ISP blames our equipment (CIsco ASA 5510) for this. I spoke to Cisco support. They looked at our configuration, and tested it. They say our configuration is correct and the ISP's equipment is doing it.
IPSMAC address*.*.*.5*.*.4cd8*.*.*.4*.*.4cd8*.*.*.3*.*.4cd8*.*.*.2.*.*.4cd8*.*.*.204*.*.4cd8*.*.*.205*.*.4cd9
As you can see above, the IP ending in 205 has a different MAC address ending in 4cd9. It should end in 4cd8. This seems to happened randomly with all IPs. Like if I restart the ASA. Some of the IPs will not work, and will show a different MAC address.We then have to wait a couple of hrs for them to start work again.
View 1 Replies
View Related
May 20, 2012
I'd like to add a name to a few ip addresses in the DHCP client table currently there is an asterix for a couple client names. the router is an ea3500.
View 2 Replies
View Related
Jan 16, 2013
In datasheet of WS-SUP720-3B - link- was said that are only supported around 256K routes (fib?rib?).With this value I can't get 2 full bgp - that is around 850K ..
The supervisor is that control this or just memory ? I said this because I have a 7204-npe-g1 whith 2 fullrouting and 1G of and he are ok..
View 3 Replies
View Related
Nov 12, 2012
We have two Cisco 3560E layer 3 switches at the core of our network. The switches are configured as an HSRP pair and the clients on our network point to the HSRP address as their default gateway. So if CORE-A dies, then CORE-B will pick up the address and the default route for the clients will continue to be available.We also need to specify a few static routes on the core switch to allow us to get to specific networks. Is there a way to do this so that the routes failover in the same way that the default gateway does?
View 2 Replies
View Related
Dec 5, 2012
I started using RIPv2 on Packet Tracer. I got two subnets to connect with two routers. After I completed that, I decided to add a third router. How to setup the Routing Table for atleast R3 ?
View 5 Replies
View Related
Oct 2, 2012
I am using Cisco 2911 & IOS version is 15.1. My problem is that after some days (e.g. 15-20 days), the routing table suddenly stops updating & then I have to enter the default route again to make it up. I am using Track 1 to track default route here. After primary link goes down, the Track is also going down but after coming the primary link up, the track is not coming up. So, I have to add the default route again to make it up.
View 2 Replies
View Related
Nov 14, 2012
We have small which I'm looking to implement and have built this on GNS3.
We have:
Router A in site 1
Router B in site 2
Router C in site 3
Router A and B are connection via a point to point 100M link and from Router C we have a 2 point to point one of which is 5Mpbs and going to Router A and Router B.
For Router C to reach Router A network it will go via Router B and these are 100M connection. When the link between Router A and B goes down. Router C should update and start using the 5m route.
For some reson, the routes are not updating. I have to do 'clea ip eigrp ne' for the routes to update and if I reload the routers all works well, it seems the problem is intermittent.
View 13 Replies
View Related
May 22, 2013
I am attempting to filter a specific host(s) from my OSPF routiing table on a ASA 5550 (ABR) using LSA prefix lists. However, when I look at the other routers in that area, I notice that ALL LSA type-3's are being removed (10 hosts are now missing from the routing table). I have verified the filter is working on the ABR, but I can't figure why ALL hosts/routes that were coming into the area are now being filtered instead of the specific one that I want to filter out.
Here is the config on the ABR:
prefix-list pdm_pl_000 seq 10 permit 206.253.180.137/32
!
!
router ospf 1
network 10.0.0.0 255.255.255.0 area 0
network 10.150.10.0 255.255.255.0 area 10
network 10.150.252.0 255.255.255.224 area 10
[code]....
The 206.253.180.137 host is actually coming from Area '3'. Am I doing something that is removing all type-3 LSA's?
View 3 Replies
View Related
Feb 6, 2013
On the 6509, with normal 67xx cards installed, where is all the mac table held, is it held on the card itself or on the supervisor? And if I use dcef cards, I gather the MSFC copies the mac table to the DFC ?
View 1 Replies
View Related
Jan 11, 2012
Cisco 1812, Version 12.3(8)YI1..What does "none" mean ?Most of mac adressess in cam has specified interface, but several has none.
View 12 Replies
View Related
Feb 19, 2012
I am in need to have the arp table cleared every 5 seconds or so on a 2800 router. I was wondering how I might be able to accomplish this.
View 4 Replies
View Related
Jul 23, 2012
My 2821 router has an arp table with the wrong ip to Mac mappings. The impact is that I can reach any host in the 10.1.1.1 subnet. I can reach hosts in the 192.168.35.0 just fine. [code] It is as if the 192.168.35.1 device is answering all arp requests as a proxy arp or something. Clear arp-cache nor clear ip arp on my 2821 have any affect.
View 1 Replies
View Related
Apr 8, 2013
we have 6500 cisco switch as a backbone switch in universty. When ı want to look mac addres table , it does no show all mac address.ı mean if ı type ;show mac address-table there are not all mac address.
View 3 Replies
View Related
Dec 6, 2011
I have 3750E swiches with IOS v. 12.2(55)SE3. Couple servers connect to ths switch, after ping of IP this servers I can see mac addresses in mac address table.
For instance:
sw1#show mac address-table vlan 20
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports(code)
---- ----------- -------- -----
When ip generate traffic to this server this mac address appear in table again on shot time (less than 10 seconds).
View 4 Replies
View Related
Feb 23, 2012
A Network Lab (governmental) did not let our cisco 2960s switches to be imported to the country and said "according to my lab tests, the maximum mac that your switch can learn is about 500 but as cisco says it should be about 8000"
they did not give me their software but i like to test it myself
Is there a software which generates thousands of MAC and inject them into switch to test the real amount shown in show mac count ?
View 3 Replies
View Related
Oct 28, 2012
I have the switch ============>>>>>
sw2960g============server linux
As u see above , the inetrface Gi0/6 , Gi0/7 are connected directly to linux server by two redundent links .
I mean that Gi0/6 is connected to interface0 in linux server
and Gi0/7 is connect to interface interface1 in linux server
Gi0/6===>vlan 1
Gi0/7===>vlan 2
each interface of linux server has a different ip and different gateway .
Now from switch, I make ping to interface 0 of linux server and i have a reply , every thing is ok but when i type the command :
#sh mac address-table | i Gi0/6
There is no Mac addresses and seems no Mac address relative to Gi0/6, I mean that doesn't it mandatorty to learn the mac address of linux server and write in mac table relative beside interface Gi0/6 ? How I could ping the server but no mac beside Gi0/6 ?
View 11 Replies
View Related
Nov 27, 2011
we have cisco WS-C6509-V-E with IOS version 12.2(33)SXI4; s3223_rp_IPSERVICESK9_WAN_M) running on a switch. I am trying to configure the command "mac-address-table synchronize" under global config mode. But when I enter the command Cisco(config)#mac-address-table ?It doesn't show the synchronize option?
View 3 Replies
View Related
Dec 22, 2011
The issue is occuring on our local LAN where my ARP requests are being modified after a period of time by the router for one host. I'm finding that the host will work fine with the correct MAC IP pairing for a period of time and then about 15-30 minutes later, the arp table is changing so the associated mac/IP address is now the mac address of the router interface.
The FastEthernet 0/1 port has no ip proxy-arp enabled and is set with ip nat inside.This only started happening after restarting the router, however the running config was saved as the startup config prior to the restart.I've tried hard-coding the entry with the command arp 10.15.4.190 c82a.1459.0579 ARPA however that is not working as expected.
The device is an 1841 ISR with the advanced IP Services bundle loaded. Is there some way that the router is viewing my host (provides DNS, Directory Services) as a intrustion attempt and somehow rejecting the packets?
View 1 Replies
View Related
Jun 30, 2012
Do I need the Universal image to perform stftp on a 3750 or 3750-X?
View 8 Replies
View Related
Jul 12, 2010
We want to configure the "mac-address-table synchronize" command on our 6500 series switches to ensure that the CAM tables on our DFCs are in synch with the PFC on the supervisor modules. url...it is recommended that we disable the routed MAC purging with the mac-address-table aging-time 0 routed-mac global configuration command. What is a routed mac entry? Are there any issues with running that mac aging-time command?
We also plan to run this command "mac-address-table aging-time 14400" to keep our ARP and CAM tables on the same aging time to reduce unicast flooding on our network. Can we run this command with the "routed-mac" command above?
View 2 Replies
View Related
May 8, 2011
My Catalayst 4507 is reaching up to 82% CPU utilization and I noticed that K2L2 Address Table R is causing the high CPU.
C4507#sh processes cpu | in HiPri|LoPri|CPU utilizationCPU utilization for five seconds: 82%/1%; one minute: 86%; five minutes: 87% 54 350533923 329104616 1065 13.27% 13.84% 13.86% 0 Cat4k Mgmt HiPri 55 1771768520 274992685 6442 59.91% 64.55% 66.04% 0 Cat4k Mgmt LoPri
C4507#sh platform health | in K2L2|%CPuK2L2 Address Table R 2.00 66.35 12 5 100 500 91 82 58 27272:55K2L2 New Static Addr 2.00 0.00 10 0 100 500 0 0 0 0:00K2L2 New Multicast A 2.00 0.00 10 5 100 500 0 0 0 0:18K2L2 Dynamic Address 2.00 0.00 10 5 100 500 0 0 0 0:16K2L2 Vlan Table Revi 2.00 0.00 12 8 100 500 0 0 0 1:22
View 2 Replies
View Related
Nov 27, 2011
We are getting log messages like
%EARL-DFC4-4-NF_USAGE: Current Netflow Table Utilization is 95%
%EARL-DFC4-4-NF_USAGE: Current Netflow Table Utilization is 99%
What this messages really means and how to get rid of these messages. We are using IOS version 12.2(33)SXJ in Catalyst 6500.
View 3 Replies
View Related
Sep 14, 2010
I've configured ip dhcp snooping on several vlans I want to monitor and the binding table doesn't seem to be building.eature DHCP is on, global ip dhcp snooping is enabled, VLAN snooping is enabled on the vlan's I want to monitor and my trusted interfaces are also configured. Alas no binding entries in the table! 7K is running 4.2(6).
View 1 Replies
View Related
