Cisco Switching/Routing :: 2960 - Software For Testing MAC Table Count
Feb 23, 2012
A Network Lab (governmental) did not let our cisco 2960s switches to be imported to the country and said "according to my lab tests, the maximum mac that your switch can learn is about 500 but as cisco says it should be about 8000"
they did not give me their software but i like to test it myself
Is there a software which generates thousands of MAC and inject them into switch to test the real amount shown in show mac count ?
View 3 Replies
ADVERTISEMENT
Jan 15, 2012
Created two 6509s as VSS with just one 10gb connection?I know it is recommended to use both the 10gb connections on the sup-720 from below configuration guide
"
Information about VSL Topology
#
A VSS contains two chassis that communicate using the VSL, which is a special port group. Configure both of the 10-Gigabit Ethernet ports on the supervisor engines as VSL ports.
"
But will the VSS come up if I use just the one?
View 2 Replies
View Related
Jan 18, 2012
I have asked to test an VPN phone for home Users. I have a BT adsl broadband at home which is going into a cisco 2900 switch. Port One is connect to the computer port 3 is connected to the Avaya VPN phone this work's. The quality is not very good, so the question is could I have qos on Port 3 which is connected to the phone?
View 4 Replies
View Related
May 2, 2013
is it easy to remove the 3750x stacking? i'd like to test one of them on a sunday and keep the other one on production. it's just two stack of 3750x, is it hard and do i really need to remove the cables on the back?
basically i need to put a different config for my testing, i gues i need to remove the cables right? and put it back on the stack before monday.
View 2 Replies
View Related
Jan 20, 2013
Our customer get the problem that the switch count the 5mins input/output rate of connected traffic interface always ZERO.The problem only occur in the module 3,4 and 5 interface, module 2 has no problems.
-------------------------------------------------------------------------------------------------
Catayst 4506E
12.2(52)SG
Chassis Type : WS-C4506-E
Power consumed by backplane : 0 Watts
Mod Ports Card Type Model Serial No.---+-----+--------------------------------------+------------------+-----------1 6 Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E 2 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 3 48 10/100/1000BaseT (RJ45) WS-X4648-RJ45-E 4 48 10/100/1000BaseT (RJ45) WS-X4648-RJ45-E 5 48 10/100/1000BaseT (RJ45) WS-X4648-RJ45-E
[code]....+
View 2 Replies
View Related
Jan 16, 2013
In datasheet of WS-SUP720-3B - link- was said that are only supported around 256K routes (fib?rib?).With this value I can't get 2 full bgp - that is around 850K ..
The supervisor is that control this or just memory ? I said this because I have a 7204-npe-g1 whith 2 fullrouting and 1G of and he are ok..
View 3 Replies
View Related
Feb 7, 2012
I have an existing stack of 4 x 2960-S switches connected by stack cables.I would like to add another 2960-S switch to the stack but am unable to as the 2960-S will only allow 4 x 2960-S switches per stack.how I would add the 5th 2960-S switch to the existing stack of 4 x 2960-S switches.
View 12 Replies
View Related
Feb 11, 2013
I have a 24 port 2960-S that is not communicating with a 2960-LST that it is directly connected to over fiber. The link is up on the LST but will not come up on the -S. What command should I use to bring up this link? I have tried no shut from the (Config-if)# prompt.
View 3 Replies
View Related
Nov 12, 2012
We have two Cisco 3560E layer 3 switches at the core of our network. The switches are configured as an HSRP pair and the clients on our network point to the HSRP address as their default gateway. So if CORE-A dies, then CORE-B will pick up the address and the default route for the clients will continue to be available.We also need to specify a few static routes on the core switch to allow us to get to specific networks. Is there a way to do this so that the routes failover in the same way that the default gateway does?
View 2 Replies
View Related
Dec 5, 2012
I started using RIPv2 on Packet Tracer. I got two subnets to connect with two routers. After I completed that, I decided to add a third router. How to setup the Routing Table for atleast R3 ?
View 5 Replies
View Related
Oct 2, 2012
I am using Cisco 2911 & IOS version is 15.1. My problem is that after some days (e.g. 15-20 days), the routing table suddenly stops updating & then I have to enter the default route again to make it up. I am using Track 1 to track default route here. After primary link goes down, the Track is also going down but after coming the primary link up, the track is not coming up. So, I have to add the default route again to make it up.
View 2 Replies
View Related
Nov 14, 2012
We have small which I'm looking to implement and have built this on GNS3.
We have:
Router A in site 1
Router B in site 2
Router C in site 3
Router A and B are connection via a point to point 100M link and from Router C we have a 2 point to point one of which is 5Mpbs and going to Router A and Router B.
For Router C to reach Router A network it will go via Router B and these are 100M connection. When the link between Router A and B goes down. Router C should update and start using the 5m route.
For some reson, the routes are not updating. I have to do 'clea ip eigrp ne' for the routes to update and if I reload the routers all works well, it seems the problem is intermittent.
View 13 Replies
View Related
May 22, 2013
I am attempting to filter a specific host(s) from my OSPF routiing table on a ASA 5550 (ABR) using LSA prefix lists. However, when I look at the other routers in that area, I notice that ALL LSA type-3's are being removed (10 hosts are now missing from the routing table). I have verified the filter is working on the ABR, but I can't figure why ALL hosts/routes that were coming into the area are now being filtered instead of the specific one that I want to filter out.
Here is the config on the ABR:
prefix-list pdm_pl_000 seq 10 permit 206.253.180.137/32
!
!
router ospf 1
network 10.0.0.0 255.255.255.0 area 0
network 10.150.10.0 255.255.255.0 area 10
network 10.150.252.0 255.255.255.224 area 10
[code]....
The 206.253.180.137 host is actually coming from Area '3'. Am I doing something that is removing all type-3 LSA's?
View 3 Replies
View Related
Feb 6, 2013
On the 6509, with normal 67xx cards installed, where is all the mac table held, is it held on the card itself or on the supervisor? And if I use dcef cards, I gather the MSFC copies the mac table to the DFC ?
View 1 Replies
View Related
Jan 11, 2012
Cisco 1812, Version 12.3(8)YI1..What does "none" mean ?Most of mac adressess in cam has specified interface, but several has none.
View 12 Replies
View Related
Feb 19, 2012
I am in need to have the arp table cleared every 5 seconds or so on a 2800 router. I was wondering how I might be able to accomplish this.
View 4 Replies
View Related
Jul 23, 2012
My 2821 router has an arp table with the wrong ip to Mac mappings. The impact is that I can reach any host in the 10.1.1.1 subnet. I can reach hosts in the 192.168.35.0 just fine. [code] It is as if the 192.168.35.1 device is answering all arp requests as a proxy arp or something. Clear arp-cache nor clear ip arp on my 2821 have any affect.
View 1 Replies
View Related
Apr 8, 2013
we have 6500 cisco switch as a backbone switch in universty. When ı want to look mac addres table , it does no show all mac address.ı mean if ı type ;show mac address-table there are not all mac address.
View 3 Replies
View Related
Feb 21, 2012
we have a 3750 and use dhcp services on the switch. every so often we run out of ip's even though we have much less users than the size of the allocated dhcp pool. I've noticed that the dhcp bind table is full but a ping-sweep only shows very few ip's being assinged and used. It looks like the IP addresses are not being released from the table even though I have decreased the lease time to 8 hours.
View 2 Replies
View Related
Jan 18, 2012
I have one VLAN on a 3750 where I do not see any MAC addresses even though it is in use. This is an unrouted VLAN between a WLC on a port- channel /LAG and an access port to an ASA for guest traffic. When I do a show MAC add I get nothing for VLAN 60 (guest DMZ) but all other VLANs seem to be OK. Spanning tree is not showing TC counters incrementing either.
I also was told when put a port on this VLAN the laptop did not get a DHCP address form the ASA, but the wireless guest clients are working fine. I can see the DHCP leases and ARP entries in the ASA and the ASA ARP in the WLC so some traffic is passing fine. I'm not onsite right now so troubleshooting is all remote which limits some options.
View 4 Replies
View Related
Dec 6, 2011
I have 3750E swiches with IOS v. 12.2(55)SE3. Couple servers connect to ths switch, after ping of IP this servers I can see mac addresses in mac address table.
For instance:
sw1#show mac address-table vlan 20
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports(code)
---- ----------- -------- -----
When ip generate traffic to this server this mac address appear in table again on shot time (less than 10 seconds).
View 4 Replies
View Related
Oct 28, 2012
I have the switch ============>>>>>
sw2960g============server linux
As u see above , the inetrface Gi0/6 , Gi0/7 are connected directly to linux server by two redundent links .
I mean that Gi0/6 is connected to interface0 in linux server
and Gi0/7 is connect to interface interface1 in linux server
Gi0/6===>vlan 1
Gi0/7===>vlan 2
each interface of linux server has a different ip and different gateway .
Now from switch, I make ping to interface 0 of linux server and i have a reply , every thing is ok but when i type the command :
#sh mac address-table | i Gi0/6
There is no Mac addresses and seems no Mac address relative to Gi0/6, I mean that doesn't it mandatorty to learn the mac address of linux server and write in mac table relative beside interface Gi0/6 ? How I could ping the server but no mac beside Gi0/6 ?
View 11 Replies
View Related
Nov 27, 2011
we have cisco WS-C6509-V-E with IOS version 12.2(33)SXI4; s3223_rp_IPSERVICESK9_WAN_M) running on a switch. I am trying to configure the command "mac-address-table synchronize" under global config mode. But when I enter the command Cisco(config)#mac-address-table ?It doesn't show the synchronize option?
View 3 Replies
View Related
Dec 22, 2011
The issue is occuring on our local LAN where my ARP requests are being modified after a period of time by the router for one host. I'm finding that the host will work fine with the correct MAC IP pairing for a period of time and then about 15-30 minutes later, the arp table is changing so the associated mac/IP address is now the mac address of the router interface.
The FastEthernet 0/1 port has no ip proxy-arp enabled and is set with ip nat inside.This only started happening after restarting the router, however the running config was saved as the startup config prior to the restart.I've tried hard-coding the entry with the command arp 10.15.4.190 c82a.1459.0579 ARPA however that is not working as expected.
The device is an 1841 ISR with the advanced IP Services bundle loaded. Is there some way that the router is viewing my host (provides DNS, Directory Services) as a intrustion attempt and somehow rejecting the packets?
View 1 Replies
View Related
Jun 27, 2012
I am looking for a way to create different routing policies for vlans on a 3750 table.
My set up is
Clients----------- 3750 -------------- ASA ---------------Servers
|
|
|
Internet Routers
What i am trying to do is on the 3750 to route private networks to my ASA on different subintefaces and all internet to my internet routers . Each VLAN has a different GW for the internet. On some case i have the ASA as a default gateway. ASA default default route is 3750 where i need the internet traffic to be spllited on the proper Boarder router.
View 1 Replies
View Related
Jul 12, 2010
We want to configure the "mac-address-table synchronize" command on our 6500 series switches to ensure that the CAM tables on our DFCs are in synch with the PFC on the supervisor modules. url...it is recommended that we disable the routed MAC purging with the mac-address-table aging-time 0 routed-mac global configuration command. What is a routed mac entry? Are there any issues with running that mac aging-time command?
We also plan to run this command "mac-address-table aging-time 14400" to keep our ARP and CAM tables on the same aging time to reduce unicast flooding on our network. Can we run this command with the "routed-mac" command above?
View 2 Replies
View Related
May 8, 2011
My Catalayst 4507 is reaching up to 82% CPU utilization and I noticed that K2L2 Address Table R is causing the high CPU.
C4507#sh processes cpu | in HiPri|LoPri|CPU utilizationCPU utilization for five seconds: 82%/1%; one minute: 86%; five minutes: 87% 54 350533923 329104616 1065 13.27% 13.84% 13.86% 0 Cat4k Mgmt HiPri 55 1771768520 274992685 6442 59.91% 64.55% 66.04% 0 Cat4k Mgmt LoPri
C4507#sh platform health | in K2L2|%CPuK2L2 Address Table R 2.00 66.35 12 5 100 500 91 82 58 27272:55K2L2 New Static Addr 2.00 0.00 10 0 100 500 0 0 0 0:00K2L2 New Multicast A 2.00 0.00 10 5 100 500 0 0 0 0:18K2L2 Dynamic Address 2.00 0.00 10 5 100 500 0 0 0 0:16K2L2 Vlan Table Revi 2.00 0.00 12 8 100 500 0 0 0 1:22
View 2 Replies
View Related
Nov 27, 2011
We are getting log messages like
%EARL-DFC4-4-NF_USAGE: Current Netflow Table Utilization is 95%
%EARL-DFC4-4-NF_USAGE: Current Netflow Table Utilization is 99%
What this messages really means and how to get rid of these messages. We are using IOS version 12.2(33)SXJ in Catalyst 6500.
View 3 Replies
View Related
Sep 14, 2010
I've configured ip dhcp snooping on several vlans I want to monitor and the binding table doesn't seem to be building.eature DHCP is on, global ip dhcp snooping is enabled, VLAN snooping is enabled on the vlan's I want to monitor and my trusted interfaces are also configured. Alas no binding entries in the table! 7K is running 4.2(6).
View 1 Replies
View Related
Aug 30, 2012
I have run into a very strange problem while doing pre-deployment vPC/STP testing in the lab with a pair of Nexus 7000s.
The basic configuration is as follows:
2x Nexus 7000 VDCs (ver 6.0(4)) are configured as vPC peers and connected with a vPC peer-link (redundant on different 10G blades) and a vPC peer-keepalive link. The switches also act as HSRP and EIGRP routers. The N7K-A switch is nominally configured as STP root and HSRP prime for all VLANs, N7K-B switch is STP backup root and HSRP secondary. STP version is PV-RSTP+. As it stands now STP root and vPC prime are on different switches, STP root is on N7K-A and vPC prime is on N7K-B.
3x Layer-2 access switches (3750-1, 3750-2, 3560-1) are configured as access switches and connected to the Nexus 7Ks with a 1G uplinks in V-pattern.
3750-1 and 3560-1 are configured for vPC as Port-Channel10 and Port-Channel12 respectively. 3750-2 is configured for STP. Vlan 35 is shared between all three switches and is enabled on the vPC peer-link (overlapping vPC and STP domains). The downlink port to the STP-only 3750-2 on N7Ks is configured as "vpc orphan suspend".
Everything seems to work fine and pings on VLAN 35 between access switches (that have mgmt interfaces in VLAN35) recover rapidly after failures. However, if I break the vpc peer-link the ping between the two vPC switches 3750-1 and 3560-1 stops. Moreover, this appears to be sporadic in nature with some vpc peer-link failure attempts recreating the problem and some not. Sometimes the problem manifests itself when the peer-link is brought back up rather than taken down.
After doing a bit of troubleshooting, I have isolated the problem to MAC address blackholing. Basically when the peer link is taken down, MAC Address table on the vPC primary switch, N7K-B, (I believe during vPC convergence) forces the traffic destined from 3750-1 to 3560-1 through the STP only switch 3750-2, which apparently goes through the RSTP convergence and enables its alternate link to N7K-B before vPC has finished its convergence. After vPC convergence is finished the path through the STP-only access layer switch 3750-2 no longer exists, as vPC will take down all vPC ports and suspend orphan ports on the vPC secondary switch (N7K-A). However the MAC Address table on N7K-B still points through the 3750-2 access layer switch instead of directly through Port-Channel 12 on N7K-B and thus creates a traffic blackhole. Issuing a ping or bouncing SVI interfaces on N7K-B fixes the problem.
View 1 Replies
View Related
Apr 28, 2012
I am little confused about the location of FIB table and adjacency table in both cisco 6500 series and fixed ports switches .In case of 6500 series switches
"Central CEF mode:The CEF FIB and adjacency tables reside on the route processor,and the route processor performs the express forwarding. Use this CEF mode when line cards are not available for CEF switching, or when features are not compatible with distributed CEF."
If line cards do no support CEF, then FIB and adjacency tables are built and are located on route processor( control plane ). Data plane operations are implemented in software and route processor performs those operations.
Some Cisco switches actually use different hardware to control the different planes. For example, the Cisco Catalyst 6500 is a modular switch that uses the Multilayer Switch.Feature Card (MSFC) for control-plane operations, and the supervisor Policy Feature Card (PFC) for the data-plane operations.
Supervisor module has has MSFC and PFC. MSFC implements control plane operation where as PFC implements data plane operation.But the first paragraph says in Central cef mode, both data plane and control plane operations are implemented by route processor. [code]
Do these switches implement the Central mode cef in same way as mentioned above. i.e
"Central CEF mode:The CEF FIB and adjacency tables reside on the route processor and the route processor performs the express forwarding. Use this CEF mode whenline cards are not available for CEF switching, or when features are not compatible with distributed CEF."Or fixed ports switches such as 3750 implement data plane operation in hardware where FIB tabe and adjacency table are maintained on Data plane.
View 3 Replies
View Related
Jan 17, 2013
My management has tasked me to give them a high level overview of the different switching we can choose for our new building.
This is what I know so far.4 Closets, each closet has 450 ports,One MDF room that is will contain one UCS Chassis and a Nimble iSCSI SAN.
I am working on the spreadsheet and it looks like this (Not totally filled):
2960s3560x3750x45064510Approx cost (Each, 48PORT, POE+, 10G uplink, Dual PS, IP BASE)
6K7K8K45K75KMax Capacity192432432192384Backplane speed206464520520ProLeast ExpensiveStackable to 9Stackable to 9ProDual PSDual PSDual PSDual PSDual PSProLayer 3 opt
Layer 3 optDual SupsDual SupsConExpensiveExpensiveConNo Dual PSConLayer 2 OnlyCannot stack more than 4
For the MDF I would like to use 2 Nexus 5548's with FEX's, and the layer 3 daughter board. For the IDF's I was thinking of two 4010's.
View 12 Replies
View Related
Nov 21, 2012
I am using a 3750 as a default gateway for multiple Vlans on a few 2960 switches. The trunk lines are configured and working and I have assigned ip addresses to each of the Vlan interfaces on the 3750. My issue is that I can only ping the ip address on the Vlan interface of the 3750 if I have a working computer plugged directly into the Vlan on the 3750. I only have 3 vlans on the 3750 that have hosts directly connected (vlans 2, 10 and 40) the other vlans ( 20 and 70) don't have any clients plugged into them on the 3750 but the hosts reside on 2 different 2960s that connect via trunk ports. How do I keep the vlan interface on the 3750 switch pingable when I don't have hosts directly connected in that vlan on the 3750? (yes, I have enabled ip routing on the 3750)
View 5 Replies
View Related