I have asked to test an VPN phone for home Users. I have a BT adsl broadband at home which is going into a cisco 2900 switch. Port One is connect to the computer port 3 is connected to the Avaya VPN phone this work's. The quality is not very good, so the question is could I have qos on Port 3 which is connected to the phone?
View 4 Repliesmy xperia phone cannot detect our own wifi connection at home.
View 1 Replies View RelatedA Network Lab (governmental) did not let our cisco 2960s switches to be imported to the country and said "according to my lab tests, the maximum mac that your switch can learn is about 500 but as cisco says it should be about 8000"
they did not give me their software but i like to test it myself
Is there a software which generates thousands of MAC and inject them into switch to test the real amount shown in show mac count ?
is it easy to remove the 3750x stacking? i'd like to test one of them on a sunday and keep the other one on production. it's just two stack of 3750x, is it hard and do i really need to remove the cables on the back?
basically i need to put a different config for my testing, i gues i need to remove the cables right? and put it back on the stack before monday.
im new to cisco asa and the model is 5515x with license plus. below is my config at home,
ciscoasa#
ciscoasa# sh run
: Saved
[Code]......
I have developing a utility which lets a user do the following :-
1)Identify the internet gateway device / router using uPnP
2)Check for the portmappings present in the gateway
3)Add / remove a port mapping from the gateway device
4)some other functions like loopback interface testing etc
Now , I need a router simulator (or any other way )which supports the following to test my work uPnP+ NAT +can be configured using SOAP XML messages although this is not a requisite as I am using Microsoft's SDK for uPnP ?Host 3 (or may be 4 is the RAM allows) virtual machines , connect them into a subnetwork using this software and then testing for the above requirements .
I've problem with IP SLA probes between two different routers.2900 (c2900-universalk9_npe-mz.SPA.151-4.M4.bin) here is set "ip sla responder" only and 2800 (c2800nm-advipservicesk9-mz.124-24.T2.bin) here is set two type of tests "udp-jitter" and "icmp-jitter" - temporary, used to check for availability of 2900 router.As a result, I've what udp-jitter doesn't work at the same time icmp-jitter test is OK.Here are the settings of IP SLA tests
ip sla 281
icmp-jitter 172.25.28.1 source-ip 192.168.28.6 num-packets 100
tos 128
frequency 120
ip sla schedule 281 life forever start-time after 00:05:45
[code]...
I have bought DRAM MEM-2900-2Gb for 2921, and received the following error...
Validation failed for DIMM0
*****System halted*****
%SPD info: DIMM0: Invalid DIMM type (only UDIMMs are supported)
Cisco C2960S IOS:12.2(55)SE5
Cisco C3560X IOS: 12.2(55)SE3
The 3560 switch is serving as an access and distribution layer switch. End devices are connected to it and it also implements IP routing via SVI and L3 ports.Auto qos voice cisco-phone has been implemented on applicable access layer ports. SRND4 is being used.
2960:
mls qos map policed-dscp 0 10 18 24 46 to 8
mls qos map cos-dscp 0 8 16 24 32 46 48 56
mls qos srr-queue output cos-map queue 1 threshold 3 4 5
mls qos srr-queue output cos-map queue 2 threshold 1 2
mls qos srr-queue output cos-map queue 2 threshold 2 3
mls qos srr-queue output cos-map queue 2 threshold 3 6 7
[code].....
Question 1:Why is the auto qos generated policed-dscp map different on these two switches?The Cisco Smart Business Architecture LAN configuration files guide [URL] does not specifically use the 3560 in their examples, they use the 3750 but it's my assumption that the same techniques, configs apply with regard to my specific feature questions. When using a 3750 in the Access layer, the guide shows (page 15) the same auto qos generated policed-dscp map configuration that is on my 2960. The SBA LAN config guide shows that when using a 3750 as a Distribution layer switch (page 26), the policed-dscp map configuration is the same that I see on my 3560.In the configuration guide for the 3750 distro switch, there is no auto qos applied as there are no access ports, so the mls qos commands are manually input. Since my 3560 does have access ports, auto qos generated the mls qos commands, and the results are the same be it following the guide and manually entering (per distro switch guidelines) or using auto qos. This leads to question 2...
Question 2:Why is the mls qos map policed-dscp configuration different depending on use as an access vs. distribution switch?
Question 3: On the 3560, access ports that have "auto qos voice cisco-phone" applied are put into queue-set 2 (output). Queue-set 2 (output) uses default values (not configured). Is this correct and desirable? If so, why? The 2960 has all ports in queue-set 1, regardless of being an access device port or a trunk port connected to the 3560 (as per the SBA LAN config guide EgressQOS macro commands). The 3560 trunk ports are all also configured to use queue-set 1 (output), again as per the SBA LAN config guide EgressQOS marco commands.
I have a few old 2600 routers (2621, different IOS's) which I'm now replacing for new one's from the 2900 series (2901, Version 15.1(4)M4).In my configuration I have two IP addresses in my LAN interface and I have HSRP configured within the secondary IP subnet range. It would be something like this:
interface GigabitEthernet0/1
ip address 172.x.x.x x.x.x.x secondary
ip address 10.z.z.z z.z.z.z
[Code].....
Now, in the new 2900 routers, my interface configuration hasn't changed however I can see that the hello packets are now sent with the source within the respective HSRP IP subnet so I had to edit my acl for that:
permit udp 172.x.x.x x.x.x.x host 224.0.0.2 eq 1985
Is there a way I can force the HSRP to work as it previously did in the old IOS's?
I have a 2900 router at branch office. This router has a 4 port switch card and two gigabyte ports. The gigabyte port is use for wan connection and the 4 port switch card is use for lan connection. I have two separate networks on my lan side. (network 1 and network 2)
I have assigned port 0,1 of the switch card to vlan1 for network 1 Ports 2,3 of the switch card is assigned vlan 20 for network 2
My problem is I would like to applied a bandwidth restriction for all data coming out from vlan20 capping same to 384 kb.
Note I do not want use QOS because this will only kickin when saturation occurs,
how to change the Baud Rate on Cisco 2900 SW utilizing ROMON ?
View 8 Replies View RelatedI know we can use copy & Paste, my questions are:
1. Before that, do I need to wipe out the existing confi on the brand new switch?
2. About using TFTP, how does this new switch connects to the TFTP? Does it mean I have to assign a real IP and put it on our network?
we ordered a data e-delivery PAK L-SL-29-DATA-K9= (FOR A 2900 SERIES ROUTER) but after we received the PAK we discovered that the client actually has a 1900 router. Any easiest way of rectifying this mistake so that we can use the PAK on a 1900 series router?
View 1 Replies View RelatedTrying to apply this config to a 2900 router and getting this error message. [code] This works ok in in a 2800 router using 12.4(25d) spservices IOS
Not working on 2911 using 15.2(3)T2 ipbase image.
How to configure a module NM-16ESW because with the command "show diag" and "show int" can not query it.
Note: the default IOS is installed, you will need to upgrade to a specific '.
I have came across this topic, and I am wondering if this images can be uploaded to any 2900 series switches or not, and if this will work as access port for more than vlans. URL...
View 2 Replies View Relatedi have 2921 router with base license . i want to upgrade to it to security k9 feature or want to enable it. i have license file with product activation key. how should i do it. if any body have screen shot file
View 1 Replies View RelatedI just purchased a used Catalyst 2900 XL switch and have not been succesful in connecting to the console via minicom 2.5 running on Ubuntu 12.04 or 11.10, I don’t even get junk charecters in the terminal or echo on input. The switch passes POST according to the LEDs on the front and the network ports are fucntional for switching purpouses.
I’m using a Prolific PL2303 USB-Serial adapter, which works with minicom to console into another device. I’ve tried every baud rate available and tried combonations of hardware flow control, software flow control, and niether.I’ve tested the pinout of the console cable and all pins map correctly according to Cisco spec.I’ve also tried Cutecom, putty, and screen. I have not tried HyperTerminal because I do not use windows.Is it possible that the previous owner disabled console access? Do I need to reboot the switch each time I test a different baud rate?
I recently copied a configuration from a router 2800 to a 2900. After a power outage no one can connect outside of the network through the new router. Before the outage all was fine. I put back the old router and all is fine which eliminates any cable or switch error. I have the router totally disconnect. I notice the configuration is in place. My question is there any diagnostics that I can run to see if there is any hardware failure. It seems to boot up fine.
View 1 Replies View RelatedI am having a problem reaching a soho linksys e1000 router through a second hop cisco 2900 router.Here is a brief topology of the network: I am using OSPF area 100 for all networks except for
192.168.2.0 on R1 to E1000 which is RIPv2
R1 directly connects to R2 with a point-to-point serial on network 192.168.12.0 /30 with ip 192.168.1.13
R1 directly connects to a a switchport using network 192.168.2.0 /24 with ip 192.168.1.75
R3 directly connects to a switchport using network 192.168.1.128.0 /25 with ip 192.168.1.129
R3 directly connects to a different cisco router using ethernet on network 192.168.1.0 with ip 192.168.1.1
E1000 directly connects to a switchport using network 192.168.2.0 /24 with ip 192.168.2.1
The switch has a vlan ip on 192.168.1.128 /25?I can ping from R1 to E1000?I can ping from R3 to R1 192.168.2.75? I can't ping from R3 to E1000 192.168.2.1?show ip route on R2 indicates that network 192.168.2.0 is reachable via the serial connection on 192.168.1.12?I have redistributed rip to ospf area 100 and OSPF to RIP on R1?I am wondering why R1 can reach E1000 on network 192.168.2.0, and why R3 can reach R1s 192.168.2.0 newtork, but R3 can't reach the E1000.There is an R2 router than can reach R1 and also cannot reach E1000, but I assume it's for the same reasons R3 can't, so I've omitted the remainder of that topology for this question.
I have a small network that i want to setup, i have 1 2900 router and i'd like to create subinterfaces for the internal. but more importantly i'd like to have the dsl modems connected to the router with traffic from one subinterface going through one modem and traffic from the other going through the other.
View 1 Replies View RelatedHad an odd issue that started up last few days.. Have a port on a cisco 2912 XL that keeps dropping (drops all packets) on a certain VLAN, but still passes others. Spanning-tree for that vlan says all ports are in forwarding status. VTP says that VLAN is still active.
This network is a little strange... 2924XL -> MotoPTP -> 2912XL -> Moto Canopy Array -> Some sites with cisco, some without all feed through canopy controller switch to single port (fa0/8) on 2912.
Getting a few of these on terminal monitoring, %RTD-1-ADDR_FLAP: FastEthernet0/8 relearning 5 addrs per min... Sometimes this is fa0/8, fa0/10, or fa0/1.
I'm thinking the switch has just gone nuts, cause fa0/1 is direct connected to a router used for VLAN1. fa0/8 is connected to a dumb switch on a canopy CMM as a trunk which i enabled bpdufilter on because of some spanning tree issues on VLAN1. fa0/10 is connected to canopy PTP back to the 2924 as a trunk. VLAN69s router is off the 2924. So there aren't really any possible alternate packet paths to this switch from another switch.
I also setup SPAN and captured all packets from fa0/8 and fa0/10 (seperately) and never seen packet storms of any kind on either VLAN1 or VLAN69.Further testing with debug, nothing on spanning tree, nothing on vtp, but on ethernet-controller addr I got some interesting results showing one mac moving from fa0/1 to fa0/8 and back to fa0/1 but it never moves, its the routers mac that is connected directly to fa0/1. Same with some macs on the other side of the PTP link saying they are bouncing from fa0/10 to fa0/8 and back to fa0/10 which isn't possible
We need to implement VLANs on my company's network. I have 3750 L3 swtich, ive setup 3 vlans for testing. ive setup SVI everything.now how do I connect it to 3com that will also use VLANs. should I set trunk port of cisco and 3com? or no need?
View 2 Replies View RelatedThe field engineer has a stand alone 24 port 2900 series switch that he has different equipment connected to and are segmented using VLANs. So for example, he's got ports 1-4 assigned to VLAN 10, 5-12 assigned to VLAN 20, 13-19 assigned to VLAN 30 and 20-24 assigned to VLAN 40. He would like all the gear on VLAN 30 to have the ablity to talk to all of the other VLANS, but VLAN 40 should not be allowed to talk with any other VLAN. Trunking would do no good here since the switch isn't connected to anything and you can only assign one VLAN per port.
Is there a way to do this within the stand alone switch? The only possible way I could think of would be to ensure that each VLAN has an assigned IP number (subnet) and doing this through access lists.
We have multiple cisco cat 2900 switches. all switches don't have cascade cable port in back panel. i want some sort of solution to manage those switch remotely.
View 9 Replies View RelatedI understand the vlans on the catalyst side of the house on 2900 to 6500 Catalyst switches.
This 7010 running nx-os 5.1(3) I did not setup, but have to manage it. Hasn't really been a proble till now.
My nexus 7010 has a Layer 2 only vlan 11. It is "Active" but the interface is "shutdown". Yet, it is passing traffic across the directly connected ports on the nexus 7010 and to other switches in my network. Vlan 11 is being set out via VTP to all my switches and things are running fine.
I need to create another L2 only Vlan. I can't seem to find any docs that indicate that a Layer2 vlan Interface on nx-os should be in "shutdown" mode as part of the setup. I do see in the docs where it has to be set "Active" as part of the process.
Is this the correct way to seutp a L2 only vlan on nex-os? Leave the interface in "shutdown" but make it "Active"?
Mystery Vlan 4 and 6
The mystery deepens. I have other L2 vlans ,Vlan4&6 that are NOT defined as "Interface Vlan4" in the nexus config, yet it is applied to GigE ports on the nexus and these Vlans 4/6is also being sent out VTP to all switches. Even weirder is that these vlans have names associated with the numbers. These are valid Vlans that were configured on the old 6509 before the Nexus was installed.
I have checked all switches, NONE are running in Server mode for VTP, all are in CLIENT. The nexus 7010 is the only device running in VTP Server mode.
I have a Catalyst 3750 router and would like to know if this can be setup to accept communications from a storage switch which uses a fibre path to then send the signal onwards to some test equipment which uses a copper ethernet connection.
View 7 Replies View RelatedAt our small business I would like to be able to test connecting to some of our websites as an external IP address user outside of our network although still being physically connected to the internal network. Any thoughts on the simplest way to set this up? I have the capability to setup vlans on our switch, could I make one of the vlans/ports have an external connection instead of an internal?
View 1 Replies View RelatedIf there is a router ISRG2 2900 with SEC license and without HSEC license, there is a limit in count of cumulative encrypted VPN tunnels of 225. Which commands can show us a number of current tunnels on the router, so we can see if we are near this limit of 225?
View 4 Replies View RelatedWhat happens with the sip phone 3905, because i cant set the rigth clock. its always display plus 2 hours from the right time in Brazil.
View 3 Replies View Relatedunderstanding of "mls qos interface stat"
I took a switch and connected it to my LAN switch is 2960 with LanBase image and PoE on it I have 3 interfaces in up state - 2 interfaces with cisco phones (6921 and 9951) nad 1 interface as uplink
here is its configuration
interface FastEthernet0/1
switchport mode access
switchport voice vlan 555
[Code].....
how we can configured 3560 for Avaya IP phone ? , we would link to use voice and data connect to the same port
View 1 Replies View Related