Cisco Switching/Routing :: Router 2900 Fail After Power Outage
Apr 22, 2013
I recently copied a configuration from a router 2800 to a 2900. After a power outage no one can connect outside of the network through the new router. Before the outage all was fine. I put back the old router and all is fine which eliminates any cable or switch error. I have the router totally disconnect. I notice the configuration is in place. My question is there any diagnostics that I can run to see if there is any hardware failure. It seems to boot up fine.
View 1 Replies
ADVERTISEMENT
Feb 28, 2011
I have a 6500 chassis with 2 power supplies. At the moment I am using the default configuration:
power-redudancy mode redundant
The problem is that an inserted module is in "power deny" state due too insufficient power.
I know, that It's not a good idea to change into combined mode (loss of redundancy), but my customers requested this anyway.
So I will change to combined mode. So here's the 1 million dollar question: "Which modules will go into power deny, if one of my power supplies fails?"
The 6500 config guide states:
"Power supply is removed withredundancy disabled
• System log and syslog messages are generated.
• System power is decreased to the power capability of one supply.
• If there is not enough power for all previously powered-up modules, some modulesare powered down and marked as power-deny in the show power oper state field."
Well, do you know if there's any way to configure some kind of priority? E.g. I definetly don't want by 10Gig Module or WiSM module to be in power deny. Can i statically make sure, those module will be powered on for sure? Like: "power enable module slot_number" How is this calculated? Or is random?
View 3 Replies
View Related
Oct 27, 2011
We had some problems with 3560G-48PS-S switches and PoE for our phones. IOS is 12.2(50)SE3. There were some problems after power outage. The switches didn't reboot because we have two eletric circuits. But after the problems we had no PoE on all ports.
The switches logged to following syslog message:
%ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/17: Power Controller reports power supply VDD under voltage
I can't find any informations in the error message decoder for that. But there was another thread here with quiet the same message, but another problem regarding RPS2300.
After reloading the device all works fine again. The workaround with the commands "power inline never" and "power inline auto" I didn't know till today.
Some information about that syslog message?
My guess is that there was a voltage swing and the switch powered down its supply? Is that possible?
View 5 Replies
View Related
Nov 28, 2012
We have a cisco catalyst 6509 with Supervisor Engine . After power outage, the switch always start in Rommon mode. Configuration register is 0X2102, we want to it always start in normal mode. What should i do?
View 3 Replies
View Related
Oct 25, 2012
I live on a college campus and we had a brief power outage today. The power is back, and we (there's 4 of us in the apartment), can only connect to the internet via ethernet cable. All of our computers show wifi as connected but no internet access, the same goes for our cell phones. We've tried resetting the modem, reconfiguring and everything.Still nothing works. The router is a JCG 108 M.
View 14 Replies
View Related
Jan 20, 2013
I have a 500 GB HD connected to the router to the usb port and It bothers me that whenever electricity fails in our city and it comes back I can still navigate and access my files on the LAN from the hard drive, but I lose the connection to the router management either by my smart phone application or by accesing trought my laptop. The only way I have figured out to solve this is connecting the drive directly to my laptop and erasing the configuration files created by the router when you set the shared folders, etc. then plugging again and setting all shared folders etc.
View 9 Replies
View Related
Feb 10, 2011
Two days ago there was a quick power outage here, just one of those flicks off flicks back on deals, but when it came back on I noticed my internet wasn't working. Couldn't figure out what the deal was so after trying a few other things I ended up eliminating my Linksys WRT54G router and just using my DSL modem. Internet works fine.
Now, I've always been kind of sketchy on networking stuff, but I don't think there router is broken I just think it's been reset or something and now I don't know what setting I need to change to get it back to working order.
Here's the kicker though. I had the DSL modem in bridge mode and the router handling traffic before but I had a huge issue with that where my Steam would only download at 10-15 KB/s. Not only that but it would take forever to login and crash constantly. This would happen on my brother's computer too, which is on the same network. I could never figure out how to fix it as forwarding ports had no effect and every other fix I could think of amounted to nothing as well. Hell, I even did a fresh install to no avail.
Now going straight into the modem my Steam is downloading at full speed and there's no slow login or crashing issues. The thing that boggles my mind though is that more than once before I tried doing this very same thing, going straight into the modem, and it didn't fix the problem.
Ideally I want to get the router back up and running and keep my Steam in full working order, essentially to have my cake and eat it too, but the priority is to get the router back up in running as I have another PC on this network, plus a 360, a PC, a wireless printer, and two Wii's.
View 10 Replies
View Related
Jan 2, 2013
My WRT320N loses the configuration every time there is a power outage, the unit is unplugged or the reset button is pressed.
View 2 Replies
View Related
Apr 18, 2012
I have a WRT160N v3. After a power outage yesterday the system keeps restarting in a cycle.
View 1 Replies
View Related
Apr 28, 2011
I am on a surge protector and we lost power last night. This morning we were stilling experiencing a brown out but now the power is back 100%. I've walked through the E1000 router reset and not matter what I do, all the lights except the power light blink rapidly and dimly. Could the router be fried even though it's on a surge protector???? It's less than 6 months old so hopefully still covered by warranty.
View 9 Replies
View Related
Mar 14, 2012
We had a power outage the other day, and now the wireless router cannot connect to the internet. Network Magic shows there is no connection from the device to the internet. I tried repairing it through Network Magic but it wasn't able to fix it.
My PC is directly connected to the wireless device by LAN cable. If I connect the PC directly to my DSL router I can connect to the internet, but not if I connect to the wireless router and from there to my DSL router. I tried resetting the wireless router to factory defaults and then going to [URL] and resetting up the router security settings. But Network Magic still shows the bad internet connection.
I then tried resetting the router to factory defaults again and installing it from scratch using the setup CD but that failed as well. I'm not at home right now so can't remember exactly at which point it was but I think it was either when the setup wizard tried to detect the device or install the device.This is the second time I've had to reset up my router due to power outage. Last time I was able to get it working by doing the first steps above.
View 2 Replies
View Related
May 12, 2013
I have a Cisco EA4500 wireless router. The only issue I have had with this router is when power gets disconnected or if I have a power outage, I have to go through some loops to get it to work again usually taking upwards of 45 minutes to fix.
View 1 Replies
View Related
Oct 13, 2012
Latest firmware with CCC corrupted after power outage. I reseet the e4500 several times and tried to reload the firmware and still no good. Only way I got it back up is to install the older non-CCC version 2.37. Strange all was fine until the power outage. Not sure if I should even bother to upgrade to 2.38 again.
View 2 Replies
View Related
Jan 19, 2013
Immediately after a power outage, my internet connection predictably drops after a set period of time or usage. It is either after about 30 min or 5-15 mins of watching Netflix. I have a modem hooked up to a wireless router and use the network on my iPhone, laptop and Roku. Since the problem, I have dropped to just having my laptop connected but this has not worked. The wireless network will disappear after the 5 - 20 mins, the light on the modem and router will show no internet (all other lights are normal). Internet connection will be reestablished if I either unplug both the modem and the router (not just one or the other) OR if I unplug the ethernet line from the modem to the router and plug it directly into my laptop (the internet light on the modem will go from "off" to "on"). Despite internet connection working from transferring from the router to the laptop if I connect it back to the router, the internet lights goes off again (resolves upon unplugging and plugging modem and router back in). The internet has not yet dropped when it is physically plugged into my laptop.
I have tried the following:
-Powercycling (temp fix until it crashes again)
-Plugging into a different outlet (I cannot connect it to a different phone line, only have 1 with DSL. Also, I do not have phone service or cable, just internet via DSL)
-Resetting modem
-Resetting 2 different routers
-Calling ISP, their test of the modem was inconclusive
Again, my wifi does not see my network whenever the internet is dropped or the ethernet cord is unplugged from the modem. The outlets I have it plugged into has some type of electrical issue, two electrical devices have shorted out in the room they are in. I do not think this issue is electrical, everything seems to have constant power (unless the power outage shorted out something in the modem). Below are some details of my modem and router. I will provide any additional info requested. I will gladly buy a new modem but I want to see if it can be fixed first.
My modem: Westell
WireSpeed Dual Connect
Model: A90-210030-04
DSL Statistics
Line State: Up
Modulation: G.DMT-Mode
Data Path: Interleaved
[code].....
Router: Linksys E2000 Internet Connection Type: Automatic Config - DHCP (I tried PPPoE and it never got a valid IP address from my ISP)
View 3 Replies
View Related
Apr 4, 2012
I'm running Windows Vista desktop on a wireless network. It's been working fine for months. Just lost power for a minute today and ever since I can't connect to the internet, only locally. My desktop can't even identify the network. My laptop (I'm using it to send this message) is also wirelessly connected and works fine, as do other wifi enabled devices in the house. I've done the power off and on for the modem and the router but it's made no difference. I've rebooted the desktop system too. I've run the ipconfig /all and am concerned I have no Default Gateway listed.
View 6 Replies
View Related
Sep 16, 2012
The power went out a few days ago and ever since it came back on I can't detect/connect to the wifi that we have. All the other computers work fine, except for mine. How do i fix this problem?
View 3 Replies
View Related
Aug 23, 2012
So my den pc is 192.168.1.4 and the kids xbox is 192.168.1.6 well i set the port forwards for my ip address for my security cameras and I set the kids portforward for the xbox. Well after a power outage, the power comes back on and randomly assigns everything a new address. Well the portforward for the secuirty cam might be on the xbox, or the laptop or the guest pc or my den pc at random?
View 2 Replies
View Related
Nov 22, 2012
During a password recovery on a cisco 3750 switch there was a power outage and now I can’t console into the switch.
View 1 Replies
View Related
Dec 8, 2011
The power went out in the room where my desktop and router and modem and everything is located. The electrical outlet that all of those things were connected to suddenly stopped working so I had to relocate everything to the other electrical outlet in the room. Everything is working fine again, including the internet connection on my desktop, but now my laptop in the other room will not recognize my wireless connection. It gives me a list of available networks, but none of which are my own. Which makes no sense, as everything is working as normal on my desktop. I tried to "manually connect to a wireless network" by typing in the name and proper security type/encryption type and password, however it tells me a network called (my network name) already exists, and it says "use the existing network. Open the 'connect to a network' dialog so I can connect." or "choose a different name." When I choose the former option, the list of available networks pops up again but mine is not on there. And it should be, as I'm definitely in close range of my router.
[code]....
View 5 Replies
View Related
Dec 16, 2012
I have two RV180W's which are excellent units in almost all respects. The one really noticeable problem is that when I have a power outage (which I have quite a lot in rural France) my RV180W does not automatically restart when the power is restored. Is it not possible to fix this in the next firmware upgrade, or have I missed something in the router menu/setup which I should have set.....?
View 1 Replies
View Related
Apr 4, 2013
I have a small network that i want to setup, i have 1 2900 router and i'd like to create subinterfaces for the internal. but more importantly i'd like to have the dsl modems connected to the router with traffic from one subinterface going through one modem and traffic from the other going through the other.
View 1 Replies
View Related
Sep 21, 2011
Dell pc studio 450s will not recognize network connection after power outage. Have run diagnostic fix multiple times but to avail. I have roadrunner cable broadband connected to voyage router and then to wireless router. Wireless router and vonage works (as evidenced by this email using iPad)
Have already reset everything multiple times including unplugging modem and pc.
From what I understand the pc is getting gatewayaddress or does not recognize.
View 5 Replies
View Related
Apr 22, 2012
I am using Scientific Linux 6.2 (Variant of RHEL / CentOS) . Every day at a particular time there is a power outage at my place, and after 1 hour power is restored. My laptop is connected to a network switch, that has no Backup power, and connection is disconnected when power is gone. Laptop keeps running in battery power.
Now when power is restored, the ethernet connection (eth0) is not automatically restored in linux. It only says connection available under wired connection. The same thing happens to the Wireless Network Connections. What can I do to automatically connect to these networks, whenever they are available?
View 2 Replies
View Related
Jan 2, 2012
All of our VoIP phones bounced (re-registered) in the middle of the work day and we do not know why. There is no maintenance going on at this time. The phones came back up right away. Upon further investigation, I only found one error message on our core switch (WS-6509 running IOS ver. 12.2(18)SXF13) and I'm wondering if that was the cause:
Jan 3 13:51:04.030: %SIBYTE-SP-5-SB_OUT_OF_RX_DSCR_CH1: Out of RX descriptors on mac 0 - channel 1 (count: 299)
I cannot find any other instances of this error message from the internet.
View 1 Replies
View Related
Nov 22, 2011
I attempted to enable jumbo frames on a Nexus 5010 (NX-OS version 4.2(1)N1(1)). I created the policy map below and lost access to the switch.
policy-map type network-qos jumbo
class type network-qos class-default
mtu 9216
After recovery I see from the logs that all vlans and interface were suspended. I've attempted to look for reasons for a compatibility issue but I am unable to find what is checked and what could have been incompatible. The other troubling thing is the adjacent switch suspended its interfaces too but no change was done there. What I need to look out for so that this does not happen again?
2011 Nov 22 23:43:09 phx-ipcg1dwfcma %ETHPORT-3-IF_ERROR_VLANS_SUSPENDED: VLANs 1,10,601 on Interface port-channel1 are being suspen
ded. (Reason: QoSMgr Network QoS configuration incompatible)
2011 Nov 22 23:43:09 phx-ipcg1dwfcma %ETHPORT-5-IF_TRUNK_DOWN: Interface port-channel1, vlan 1,10,601 down
2011 Nov 22 23:43:09 phx-ipcg1dwfcma %ETHPORT-3-IF_ERROR_VLANS_SUSPENDED: VLANs 10 on Interface port-channel508 are being suspended.
[code]....
View 9 Replies
View Related
Jun 9, 2013
I am receiving the following error on 3750 stack switches. have already verified the power status and found ok.
IOS used: Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
211540: Jun 10 10:45:17.935 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS: Switch 4's power stack has unbalanced power supplies
211541: Jun 10 10:46:18.045 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS:
[Code]....
View 1 Replies
View Related
Sep 4, 2012
After stacking two 3750X switches, with four equal power-supply's, with StackWise and PowerStack , still got the next message every few hours %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding (gn4m-rt1p08-04-2)( note that the message revers to the second switch in the stack ) although the stackwise and powerstack on the switches is oke and are working correctly. !
Config : Stack-power in power-sharing mode/strict With CLI on the switch : All the power supply's and stack-power details, prio look OK.
Only: LMS prime /inventory/cisco-view/configure/power supply status result : some power supply's are marked as disabled.with the command > power supply 2 slot a off/on I manage to get the status back to "normal", but after a few hours some power supply's are again marked as "disabled".
Looks like SNMP en IOS difference from opinion.
Hardware
WS-C3750X-24S-S
C3KX-PWR-350WAC
Software
15.0(2)SE
C3750E-UNIVERSALK9-M
View 5 Replies
View Related
Apr 14, 2013
We have two switches of the same model (WS-C3560-48PS-S) that are not providing PoE. I'm trying to remotely determine what the cause of the issue is.
Here is some output.
Hostname#show power inlineAvailable:0.0(w) Used:0.0(w) Remaining:0.0(w)
Interface Admin Oper Power Device Class Max (Watts)--------- ------ ---------- ------- ------------------- ----- ----Fa0/1 auto off 0.0 n/a n/a 15.4Fa0/2 auto off 0.0 n/a n/a 15.4Fa0/3 auto off 0.0 n/a n/a 15.4Fa0/4 auto off 0.0 n/a n/a 15.4Fa0/5 auto off 0.0 n/a n/a 15.4Fa0/6 auto off 0.0 n/a n/a 15.4Fa0/7 auto off 0.0 n/a n/a 15.4Fa0/8 auto off 0.0 n/a n/a 15.4Fa0/9 auto off 0.0 n/a n/a 15.4Fa0/10 auto off 0.0 n/a n/a 15.4(code)
View 1 Replies
View Related
Apr 4, 2012
In a stand alone 3750x switch configuration, can the secondary power supply only act as a redundant power supply (active/standby), or can it become a "pool" of power similar to power sharing mode for StackPower (somewhat active/active)? I understand there is no stack involved here but I'm curious if this functionality is possible.
View 1 Replies
View Related
Apr 11, 2013
I've problem with IP SLA probes between two different routers.2900 (c2900-universalk9_npe-mz.SPA.151-4.M4.bin) here is set "ip sla responder" only and 2800 (c2800nm-advipservicesk9-mz.124-24.T2.bin) here is set two type of tests "udp-jitter" and "icmp-jitter" - temporary, used to check for availability of 2900 router.As a result, I've what udp-jitter doesn't work at the same time icmp-jitter test is OK.Here are the settings of IP SLA tests
ip sla 281
icmp-jitter 172.25.28.1 source-ip 192.168.28.6 num-packets 100
tos 128
frequency 120
ip sla schedule 281 life forever start-time after 00:05:45
[code]...
View 3 Replies
View Related
Nov 20, 2012
I have bought DRAM MEM-2900-2Gb for 2921, and received the following error...
Validation failed for DIMM0
*****System halted*****
%SPD info: DIMM0: Invalid DIMM type (only UDIMMs are supported)
View 5 Replies
View Related
Oct 15, 2012
Cisco C2960S IOS:12.2(55)SE5
Cisco C3560X IOS: 12.2(55)SE3
The 3560 switch is serving as an access and distribution layer switch. End devices are connected to it and it also implements IP routing via SVI and L3 ports.Auto qos voice cisco-phone has been implemented on applicable access layer ports. SRND4 is being used.
2960:
mls qos map policed-dscp 0 10 18 24 46 to 8
mls qos map cos-dscp 0 8 16 24 32 46 48 56
mls qos srr-queue output cos-map queue 1 threshold 3 4 5
mls qos srr-queue output cos-map queue 2 threshold 1 2
mls qos srr-queue output cos-map queue 2 threshold 2 3
mls qos srr-queue output cos-map queue 2 threshold 3 6 7
[code].....
Question 1:Why is the auto qos generated policed-dscp map different on these two switches?The Cisco Smart Business Architecture LAN configuration files guide [URL] does not specifically use the 3560 in their examples, they use the 3750 but it's my assumption that the same techniques, configs apply with regard to my specific feature questions. When using a 3750 in the Access layer, the guide shows (page 15) the same auto qos generated policed-dscp map configuration that is on my 2960. The SBA LAN config guide shows that when using a 3750 as a Distribution layer switch (page 26), the policed-dscp map configuration is the same that I see on my 3560.In the configuration guide for the 3750 distro switch, there is no auto qos applied as there are no access ports, so the mls qos commands are manually input. Since my 3560 does have access ports, auto qos generated the mls qos commands, and the results are the same be it following the guide and manually entering (per distro switch guidelines) or using auto qos. This leads to question 2...
Question 2:Why is the mls qos map policed-dscp configuration different depending on use as an access vs. distribution switch?
Question 3: On the 3560, access ports that have "auto qos voice cisco-phone" applied are put into queue-set 2 (output). Queue-set 2 (output) uses default values (not configured). Is this correct and desirable? If so, why? The 2960 has all ports in queue-set 1, regardless of being an access device port or a trunk port connected to the 3560 (as per the SBA LAN config guide EgressQOS macro commands). The 3560 trunk ports are all also configured to use queue-set 1 (output), again as per the SBA LAN config guide EgressQOS marco commands.
View 1 Replies
View Related
Feb 21, 2013
I have a few old 2600 routers (2621, different IOS's) which I'm now replacing for new one's from the 2900 series (2901, Version 15.1(4)M4).In my configuration I have two IP addresses in my LAN interface and I have HSRP configured within the secondary IP subnet range. It would be something like this:
interface GigabitEthernet0/1
ip address 172.x.x.x x.x.x.x secondary
ip address 10.z.z.z z.z.z.z
[Code].....
Now, in the new 2900 routers, my interface configuration hasn't changed however I can see that the hello packets are now sent with the source within the respective HSRP IP subnet so I had to edit my acl for that:
permit udp 172.x.x.x x.x.x.x host 224.0.0.2 eq 1985
Is there a way I can force the HSRP to work as it previously did in the old IOS's?
View 3 Replies
View Related
