Cisco Switching/Routing :: 3560G-48PS-S - PoE Lockout After Power Outage
Oct 27, 2011
We had some problems with 3560G-48PS-S switches and PoE for our phones. IOS is 12.2(50)SE3. There were some problems after power outage. The switches didn't reboot because we have two eletric circuits. But after the problems we had no PoE on all ports.
The switches logged to following syslog message:
%ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/17: Power Controller reports power supply VDD under voltage
I can't find any informations in the error message decoder for that. But there was another thread here with quiet the same message, but another problem regarding RPS2300.
After reloading the device all works fine again. The workaround with the commands "power inline never" and "power inline auto" I didn't know till today.
Some information about that syslog message?
My guess is that there was a voltage swing and the switch powered down its supply? Is that possible?
View 5 Replies
ADVERTISEMENT
Apr 14, 2013
We have two switches of the same model (WS-C3560-48PS-S) that are not providing PoE. I'm trying to remotely determine what the cause of the issue is.
Here is some output.
Hostname#show power inlineAvailable:0.0(w) Used:0.0(w) Remaining:0.0(w)
Interface Admin Oper Power Device Class Max (Watts)--------- ------ ---------- ------- ------------------- ----- ----Fa0/1 auto off 0.0 n/a n/a 15.4Fa0/2 auto off 0.0 n/a n/a 15.4Fa0/3 auto off 0.0 n/a n/a 15.4Fa0/4 auto off 0.0 n/a n/a 15.4Fa0/5 auto off 0.0 n/a n/a 15.4Fa0/6 auto off 0.0 n/a n/a 15.4Fa0/7 auto off 0.0 n/a n/a 15.4Fa0/8 auto off 0.0 n/a n/a 15.4Fa0/9 auto off 0.0 n/a n/a 15.4Fa0/10 auto off 0.0 n/a n/a 15.4(code)
View 1 Replies
View Related
Jan 13, 2013
I have configured DHCP snooping on a WS-3560G-48PS running IOS 12.2(58)SE2 ipservicesk9 variant.When I enable DHCP snooping clients don't get IP addresses, when DHCP snooping is disabled, everything works fine.I have set up a SPAN port and run a capture (attached) on the traffic. Wireshark notes the Seconds elapsed field appeared to be encoded in little-endian but only on some packets. Apart from that, I can see nothing wrong with the DHCP Offer responses from my DHCP server.Attachment config.txt contains the interesting parts of the configuration. Please note g0/32 has been set to ARP inspection trust as without working DHCP snooping it would require a static bind.Is there any way of figuring out which option can't be parsed? Is there a way to force forwarding of unparsable DHCP packets while still running DHCP snooping?
View 3 Replies
View Related
Nov 23, 2011
I need to prepare a Bill of Material for WS-C3560G-48PS-S switch.
Whether we should go for CAB-AC-JPN - AC power cord for Japan OR CAB-AC-ACE AC power cord for Europ
View 2 Replies
View Related
Apr 22, 2013
I recently copied a configuration from a router 2800 to a 2900. After a power outage no one can connect outside of the network through the new router. Before the outage all was fine. I put back the old router and all is fine which eliminates any cable or switch error. I have the router totally disconnect. I notice the configuration is in place. My question is there any diagnostics that I can run to see if there is any hardware failure. It seems to boot up fine.
View 1 Replies
View Related
Mar 28, 2012
In my office we bought 7 cisco 3750X - 48PS switches. We configured Data Stacking between those switches. We also want to configure Power Stacking between those 7 devices.
I found in the Data Sheet that we can only configure 4 devices in power stacking at a time. If it is like that how to configure the rest of 3 devices. Need configuring power stacking between those devices in a better way..
power stack cable part no we have is
CAB-SPWR-30CM
View 2 Replies
View Related
Jun 21, 2011
We are using WS-C3560G-48PS connected via UPS power supply. Whenever raw power supply gets fluctuates few of the IP phones (Alcatel) gets reset although switch is remain up and running. We checked the same by disconnecting the raw power supply but we didn't found any packet loss from the node which are connected through this switch. But few IP phone gets reset. What could be the reason
View 2 Replies
View Related
Jul 22, 2012
I have a switch 3560v2 with an IOS 12.2(50) SE1.All the lights ON and console error message below:POST: inline power post failed for port 0 up to port 15.Then, the system hanged and all lights (indicator) ON.
View 5 Replies
View Related
Nov 28, 2012
We have a cisco catalyst 6509 with Supervisor Engine . After power outage, the switch always start in Rommon mode. Configuration register is 0X2102, we want to it always start in normal mode. What should i do?
View 3 Replies
View Related
Apr 17, 2013
I have production stack in the following config:
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 52 WS-C3750-48P 12.2(25)SEE4 C3750-IPSERVICESK9-M
2 52 WS-C3750-48P 12.2(25)SEE4 C3750-IPSERVICESK9-M
I want to add 3-rd switch to it:
Switch: WS-C3750G-48PS 12.2(25)SEE3 C3750-IPSERVICESK9-M
Will this configuration work? My main concern is IOS difference?
View 3 Replies
View Related
Mar 3, 2013
I have 3750-48PS-S in production and would like to stack it with C3750G-48PS. Both switches are running code:
c3750-ipservicesk9-mz.122-50.SE3.bin
View 3 Replies
View Related
Apr 4, 2012
I'm running Windows Vista desktop on a wireless network. It's been working fine for months. Just lost power for a minute today and ever since I can't connect to the internet, only locally. My desktop can't even identify the network. My laptop (I'm using it to send this message) is also wirelessly connected and works fine, as do other wifi enabled devices in the house. I've done the power off and on for the modem and the router but it's made no difference. I've rebooted the desktop system too. I've run the ipconfig /all and am concerned I have no Default Gateway listed.
View 6 Replies
View Related
Sep 16, 2012
The power went out a few days ago and ever since it came back on I can't detect/connect to the wifi that we have. All the other computers work fine, except for mine. How do i fix this problem?
View 3 Replies
View Related
Oct 25, 2012
I live on a college campus and we had a brief power outage today. The power is back, and we (there's 4 of us in the apartment), can only connect to the internet via ethernet cable. All of our computers show wifi as connected but no internet access, the same goes for our cell phones. We've tried resetting the modem, reconfiguring and everything.Still nothing works. The router is a JCG 108 M.
View 14 Replies
View Related
Aug 23, 2012
So my den pc is 192.168.1.4 and the kids xbox is 192.168.1.6 well i set the port forwards for my ip address for my security cameras and I set the kids portforward for the xbox. Well after a power outage, the power comes back on and randomly assigns everything a new address. Well the portforward for the secuirty cam might be on the xbox, or the laptop or the guest pc or my den pc at random?
View 2 Replies
View Related
Nov 22, 2012
During a password recovery on a cisco 3750 switch there was a power outage and now I can’t console into the switch.
View 1 Replies
View Related
Dec 8, 2011
The power went out in the room where my desktop and router and modem and everything is located. The electrical outlet that all of those things were connected to suddenly stopped working so I had to relocate everything to the other electrical outlet in the room. Everything is working fine again, including the internet connection on my desktop, but now my laptop in the other room will not recognize my wireless connection. It gives me a list of available networks, but none of which are my own. Which makes no sense, as everything is working as normal on my desktop. I tried to "manually connect to a wireless network" by typing in the name and proper security type/encryption type and password, however it tells me a network called (my network name) already exists, and it says "use the existing network. Open the 'connect to a network' dialog so I can connect." or "choose a different name." When I choose the former option, the list of available networks pops up again but mine is not on there. And it should be, as I'm definitely in close range of my router.
[code]....
View 5 Replies
View Related
Dec 16, 2012
I have two RV180W's which are excellent units in almost all respects. The one really noticeable problem is that when I have a power outage (which I have quite a lot in rural France) my RV180W does not automatically restart when the power is restored. Is it not possible to fix this in the next firmware upgrade, or have I missed something in the router menu/setup which I should have set.....?
View 1 Replies
View Related
Jan 20, 2013
I have a 500 GB HD connected to the router to the usb port and It bothers me that whenever electricity fails in our city and it comes back I can still navigate and access my files on the LAN from the hard drive, but I lose the connection to the router management either by my smart phone application or by accesing trought my laptop. The only way I have figured out to solve this is connecting the drive directly to my laptop and erasing the configuration files created by the router when you set the shared folders, etc. then plugging again and setting all shared folders etc.
View 9 Replies
View Related
Feb 10, 2011
Two days ago there was a quick power outage here, just one of those flicks off flicks back on deals, but when it came back on I noticed my internet wasn't working. Couldn't figure out what the deal was so after trying a few other things I ended up eliminating my Linksys WRT54G router and just using my DSL modem. Internet works fine.
Now, I've always been kind of sketchy on networking stuff, but I don't think there router is broken I just think it's been reset or something and now I don't know what setting I need to change to get it back to working order.
Here's the kicker though. I had the DSL modem in bridge mode and the router handling traffic before but I had a huge issue with that where my Steam would only download at 10-15 KB/s. Not only that but it would take forever to login and crash constantly. This would happen on my brother's computer too, which is on the same network. I could never figure out how to fix it as forwarding ports had no effect and every other fix I could think of amounted to nothing as well. Hell, I even did a fresh install to no avail.
Now going straight into the modem my Steam is downloading at full speed and there's no slow login or crashing issues. The thing that boggles my mind though is that more than once before I tried doing this very same thing, going straight into the modem, and it didn't fix the problem.
Ideally I want to get the router back up and running and keep my Steam in full working order, essentially to have my cake and eat it too, but the priority is to get the router back up in running as I have another PC on this network, plus a 360, a PC, a wireless printer, and two Wii's.
View 10 Replies
View Related
Sep 21, 2011
Dell pc studio 450s will not recognize network connection after power outage. Have run diagnostic fix multiple times but to avail. I have roadrunner cable broadband connected to voyage router and then to wireless router. Wireless router and vonage works (as evidenced by this email using iPad)
Have already reset everything multiple times including unplugging modem and pc.
From what I understand the pc is getting gatewayaddress or does not recognize.
View 5 Replies
View Related
Jan 2, 2013
My WRT320N loses the configuration every time there is a power outage, the unit is unplugged or the reset button is pressed.
View 2 Replies
View Related
Apr 18, 2012
I have a WRT160N v3. After a power outage yesterday the system keeps restarting in a cycle.
View 1 Replies
View Related
Apr 28, 2011
I am on a surge protector and we lost power last night. This morning we were stilling experiencing a brown out but now the power is back 100%. I've walked through the E1000 router reset and not matter what I do, all the lights except the power light blink rapidly and dimly. Could the router be fried even though it's on a surge protector???? It's less than 6 months old so hopefully still covered by warranty.
View 9 Replies
View Related
Mar 14, 2012
We had a power outage the other day, and now the wireless router cannot connect to the internet. Network Magic shows there is no connection from the device to the internet. I tried repairing it through Network Magic but it wasn't able to fix it.
My PC is directly connected to the wireless device by LAN cable. If I connect the PC directly to my DSL router I can connect to the internet, but not if I connect to the wireless router and from there to my DSL router. I tried resetting the wireless router to factory defaults and then going to [URL] and resetting up the router security settings. But Network Magic still shows the bad internet connection.
I then tried resetting the router to factory defaults again and installing it from scratch using the setup CD but that failed as well. I'm not at home right now so can't remember exactly at which point it was but I think it was either when the setup wizard tried to detect the device or install the device.This is the second time I've had to reset up my router due to power outage. Last time I was able to get it working by doing the first steps above.
View 2 Replies
View Related
May 12, 2013
I have a Cisco EA4500 wireless router. The only issue I have had with this router is when power gets disconnected or if I have a power outage, I have to go through some loops to get it to work again usually taking upwards of 45 minutes to fix.
View 1 Replies
View Related
Oct 13, 2012
Latest firmware with CCC corrupted after power outage. I reseet the e4500 several times and tried to reload the firmware and still no good. Only way I got it back up is to install the older non-CCC version 2.37. Strange all was fine until the power outage. Not sure if I should even bother to upgrade to 2.38 again.
View 2 Replies
View Related
Apr 22, 2012
I am using Scientific Linux 6.2 (Variant of RHEL / CentOS) . Every day at a particular time there is a power outage at my place, and after 1 hour power is restored. My laptop is connected to a network switch, that has no Backup power, and connection is disconnected when power is gone. Laptop keeps running in battery power.
Now when power is restored, the ethernet connection (eth0) is not automatically restored in linux. It only says connection available under wired connection. The same thing happens to the Wireless Network Connections. What can I do to automatically connect to these networks, whenever they are available?
View 2 Replies
View Related
Sep 11, 2012
I am in the process of upgrading our stack of 4 switches consist of WS-C3750G-48PS. Upon reading release notes found that there are two versions of release notes 1 day apart, the one 02 Sep 2012 saying that WS-C3750-48PS is not supported in this version. Then in release next day 03 Sep 2012 that note has been removed. Which one is correct. Is it supported with my model of switch or not. Also unable to update boot path in the stack switches, "switch all" is not supported in the current IOS. Any other way to update it. Master switch has new boot path but unable to change in slaves.
View 2 Replies
View Related
Dec 7, 2011
We recently connected a RPS 2300 to our switch WS-C3750G-48PS-E with IOS c3750-ipservicesk9-mz.122-53.SE2.bin.However i do not see any RPS details in the"show env" output.I believe i should get the RPS Name and its Serial and the port number in the output, but i am not finding it in the output. I did reload the switch but still couldnot get this udpated.
View 3 Replies
View Related
Jan 19, 2013
Immediately after a power outage, my internet connection predictably drops after a set period of time or usage. It is either after about 30 min or 5-15 mins of watching Netflix. I have a modem hooked up to a wireless router and use the network on my iPhone, laptop and Roku. Since the problem, I have dropped to just having my laptop connected but this has not worked. The wireless network will disappear after the 5 - 20 mins, the light on the modem and router will show no internet (all other lights are normal). Internet connection will be reestablished if I either unplug both the modem and the router (not just one or the other) OR if I unplug the ethernet line from the modem to the router and plug it directly into my laptop (the internet light on the modem will go from "off" to "on"). Despite internet connection working from transferring from the router to the laptop if I connect it back to the router, the internet lights goes off again (resolves upon unplugging and plugging modem and router back in). The internet has not yet dropped when it is physically plugged into my laptop.
I have tried the following:
-Powercycling (temp fix until it crashes again)
-Plugging into a different outlet (I cannot connect it to a different phone line, only have 1 with DSL. Also, I do not have phone service or cable, just internet via DSL)
-Resetting modem
-Resetting 2 different routers
-Calling ISP, their test of the modem was inconclusive
Again, my wifi does not see my network whenever the internet is dropped or the ethernet cord is unplugged from the modem. The outlets I have it plugged into has some type of electrical issue, two electrical devices have shorted out in the room they are in. I do not think this issue is electrical, everything seems to have constant power (unless the power outage shorted out something in the modem). Below are some details of my modem and router. I will provide any additional info requested. I will gladly buy a new modem but I want to see if it can be fixed first.
My modem: Westell
WireSpeed Dual Connect
Model: A90-210030-04
DSL Statistics
Line State: Up
Modulation: G.DMT-Mode
Data Path: Interleaved
[code].....
Router: Linksys E2000 Internet Connection Type: Automatic Config - DHCP (I tried PPPoE and it never got a valid IP address from my ISP)
View 3 Replies
View Related
Dec 13, 2011
I've a 3750-48ps-s running ios version: c3750-advipservicesk9-mz.122-46.SE.bin
I've tried to configure ipv6 on an interface but it does not give me the option.
How do I know if my ios is IPv6 capable?
View 1 Replies
View Related
Jul 9, 2012
I want to upgrade the IOS version of 3750 48PS switches. these stacks are located on different building some of the them having 2 members and some have 3 members in a stack.step by step to upgrade the IOS of these switches.
View 1 Replies
View Related
