I know we can use copy & Paste, my questions are:
1. Before that, do I need to wipe out the existing confi on the brand new switch?
2. About using TFTP, how does this new switch connects to the TFTP? Does it mean I have to assign a real IP and put it on our network?
I have an 877W router that I would like to have a 2nd pre-configured backup for. I was thinking of getting another 870 series (probably an 877) router, as the more expensive wireless option is not actually required. Am I right to assume that I could simply copy the contents of my current config.txt file onto the second router?
View 4 Replies View RelatedWe need to implement VLANs on my company's network. I have 3750 L3 swtich, ive setup 3 vlans for testing. ive setup SVI everything.now how do I connect it to 3com that will also use VLANs. should I set trunk port of cisco and 3com? or no need?
View 2 Replies View Relatedi have major problem with two new Small Business 300 Series switches.Everytime i try to save the running config i get a GUI error message: "Another copy process is active, please try again later."It's also not possible to re-flash the firmware because the GUI stops responding.I have also tried to do this via console access and this produces a "the copy utility is occupied by another user" error message.-> so this is not a browser based problem.My first thought was that the switch (SG 300-28) is faulty so i unpacked the next new one (SF 300)and got the same error messages!Then i had a 2 hour webex support session with the Cisco Small Business Support and they did not found a reason for this behavior.Both switches are working normally, you can configure them, but after a reboot they are back to factory default again There is no possibilty for copy running config to startup config and it's also not possible to flash the firmware.(Web GUI & Console). tell me if this is a fundamental problem of the 300 Series?
View 6 Replies View RelatedI have a Catalyst 4006 switch in production and a spare switch of same model. I have to quickly copy the configuration from production switch to spare switch (both L2 and L3 configurations) How do I do that?
View 6 Replies View RelatedI've goggled and searched here, and I can't seem to find what I'm looking for. I need to make a couple changes to a clients Cisco 800 series router, enable ping replies add ip addresses to the ssh ACL.I can't seem to find any basic commands for CLI anywhere.
View 2 Replies View Relatedabout to install first UC320w and wanted some sample 800 series router configurations showing required port fowarding, ACL entries and QoS examples.
View 5 Replies View RelatedI was trying to configure my Catalyst Express 500 switch (PID VID: WS-CE500-24LC V01) and i followed the step i found in a document on Cisco website but still it showed an error "Page not found" and address displayed on bar was"169.254.0.1/catalyst-express.htm).
View 1 Replies View RelatedI am looking for a Cisco document that gives me the,IP through-put on 2901, 2911 and 2921 routers with Policy based routing applied.,IOS version 15.1.3TOther processes, EIGRP Stub, VLAN routing, SRST,MGCP gateway (analog and PRI).
View 1 Replies View Relatedis there any CEoIP modules (Such as NM-CEM-4TE1) for the 2900/3900 series routers?
View 2 Replies View Relatedwhat is the maximum number of Lan-to-Lan and user vpns supported in the ISR G2 2911 and 2921?
View 5 Replies View Relatedany place I can find how many tunes does the cisco 2900 series made? site to site?
View 1 Replies View RelatedI have a brand new 2901 and I'm trying to work out what licence features I have. The output of show licence shows I have ipbasek9 feature and datak9 as EvalRightToUse feature. Is BGP included in the base feature? What will happen when the datak9 evaluation period expires?
View 1 Replies View RelatedI need to do password recovery for a 2911 router. But ı can't find any documentation about it. I can be able to login at the first login, unfortunately ı logged out without changing the password. Now I can not log in and I can not open rommon with the ctrl+break key sequence.
View 6 Replies View RelatedI have added 2900 series devices in LMS3.2.1 but same are showing "unknown"device Type in a report generated from common services DC R device List.
Both are snip enabled and responding too. What is the reason behind unknown device type so those are not reflecting in any module.
36.N007010101CRRUNKNOWN37.N007010103CRRCisco 2921 Integrated Services Router38.N007010201ASRUNKNOWN
I have a 2801 running c2801-spservicesk9-mz.124-3g.bin According to the Cisco IOS MIB locator the image supports OLD-CISCO-SYSTEM-MIB I have tried .1.3.6.1.4.1.9.2.1.55 etc to set server IP address and the filename string but without any luck.e.g.
Reason: (noSuchName) There is no such variable name in this MIB.
Failed object: iso.3.6.1.4.1.9.2.1.55.a.b.c.d (where a.b.c.d is the server IP)
I have also tried the method similar to that for Cat 3550 switches where you create a table of entries to define the transfer paramaters then activate the transfer (I think the CISCO-CONFIG-COPY-MIB)
e.g.
[URL]
C:>snmpset -v 1 -c private <device name> ccCopyProtocol.<random number> integer 1 ! 1 = tftpccCopySourceFileType.<Random number> integer 1 ! 1 = networkFileccCopyDestFileType.<Random number> integer 3 ! 3 = startup & 4 = runningccCopyServerAddress.<Random number> ipaddress "<server ip address>"ccCopyFileName. <Random number> octetstring "<file name>"ccCopyEntryRowStatus.<Random number> integer 4 ! 4 = createAndGo, or 1 = Active
To write net have the source as running (4) and the dest as network (1)
ccCopySourceFileType.<Random number> integer 4
ccCopyDestFileType.<Random number> integer 1
Clean up at the end - destroy .14 with the value of 6.
example output : -
-- earlier output omitted --
Error in packet.
Reason: (noSuchName) There is no such variable name in this MIB.
Failed object: iso.3.6.1.4.1.9.9.96.1.1.1.1.4.111
Error in packet.
[code]...
how to copy a cisco ios image from a 3750 to my pc so that i can use it to upgrade a switch on my desk.
View 3 Replies View Relatedi have 2811 router and i am coneccted via concole so i want to copy the 2811 ios to my PC is that possible?
how or give my the right decument to do this.
* idon't want to use TFTP becuse i have no ethernet connection to the router(only concole)
I have 2 Chassis 6506-E with sup 720. one of them work properly(Switch1) but another(Switc2) not boot form bootdisk and go to ROMMON mode. I Captured IOS from Switch1 with tftp but I cant Copy this image to switch 2 with tftp.
View 4 Replies View RelatedIt seems I have seen this before (and even done it once a few years ago).. but it has been a while. I have a stack with a Cisco 3750 stack that I have to replace a member.The replacement switch is a 3750X.
I think I have to upgrade the IOS of the older switch to be the same as the 3750X.
Current switch: WS-C3750G-48TS 12.2(46)SE
TO BE ADDED WS-c3570X-48 15.0 (1)SE2
It seems to me there was a way to upgrade the older switch IOS from the newer switch or downgrade the newer switch with the older IOS.I dont have the Cisco account to download updated IOSs.
I've problem with IP SLA probes between two different routers.2900 (c2900-universalk9_npe-mz.SPA.151-4.M4.bin) here is set "ip sla responder" only and 2800 (c2800nm-advipservicesk9-mz.124-24.T2.bin) here is set two type of tests "udp-jitter" and "icmp-jitter" - temporary, used to check for availability of 2900 router.As a result, I've what udp-jitter doesn't work at the same time icmp-jitter test is OK.Here are the settings of IP SLA tests
ip sla 281
icmp-jitter 172.25.28.1 source-ip 192.168.28.6 num-packets 100
tos 128
frequency 120
ip sla schedule 281 life forever start-time after 00:05:45
[code]...
I have bought DRAM MEM-2900-2Gb for 2921, and received the following error...
Validation failed for DIMM0
*****System halted*****
%SPD info: DIMM0: Invalid DIMM type (only UDIMMs are supported)
I am trying to configure redundancy with SSO and I need to get the same IOS on both supervisors. My issue is that I get an error when I try to copy the IOS from either the sup-bootdisk or the disk0 to the slavesupbootdisk. The Error is Invalid argument.
I have tried also to tftp to the slavesupbootdisk and get the same result.
I want to copy a file from one ASR1001 and copy it to another. I ntried using tftp 32 but this is not going to work as the image is 315 MB.
how to copy an image from one router directly to another router's flash, if possible?
I am trying to research the possiblity of backing up IOS and configurations from an Etherswitch module, and being able to store the files onto the Host Router's flash (3925 ISR). and then being able to recover that IOS and configuration, in case I have to replace the Etherswitch Module.
View 4 Replies View RelatedI have a 3550 switch that was replaced at a remote site with no IOS. This is a switch not a router so tftpdnld does not work.
[Code]...
The problem is the switches interface never comes up so try to connect to the tftp server. I read on google it can't be done on a switch to copy from tftp to flash in rommon mode on a switch and to use XMODEM. My problem is I do not have access to it, I ssh into a 3640 which is an access server for all devices and that is how I have console to it, how to use XMODEM over ssh.
But I'm fairly certain that there has to be a way to just copy it from tftp? I have a 3550 local and when I put it in rommon mode it stops the port check at port, port 1 goes from green when you plug it in to off then port 2 changes to amber and the rest green. So just by the look of this I would believe tftp would work; you just need to use port 1.
I have a 3550 switch that I am trying to upgrade the IOS on.I am trying to copy to a TFTP server.I am receiving a socket error.I saw that this can be fixed with
Switch#config t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#no service config
Switch(config)#exit
Switch#
00:13:47: %SYS-5-CONFIG_I: Configured from console by console
Switch#reload
I have done this 3 times to no avail.My TFTPd32 server on my pc is working fine.Here is the error
Switch#sh flas
Directory of flash:/
2 -rwx 556 Mar 1 1993 00:33:53 +00:00 vlan.dat
4 -rwx 3775 Mar 1 1993 00:37:54 +00:00 config.text
5 -rwx 24 Mar 1 1993 00:37:54 +00:00 private-config.text
6 -rwx 5687963 Mar 16 2007 01:05:23 +00:00 c3550-ipbasek9-mz.122-25.SEB4.bin
8 drwx 192 Mar 1 1993 00:04:40 +00:00 c3550-i9q3l2-mz.121-22.EA1a
[code]......
Cisco C2960S IOS:12.2(55)SE5
Cisco C3560X IOS: 12.2(55)SE3
The 3560 switch is serving as an access and distribution layer switch. End devices are connected to it and it also implements IP routing via SVI and L3 ports.Auto qos voice cisco-phone has been implemented on applicable access layer ports. SRND4 is being used.
2960:
mls qos map policed-dscp 0 10 18 24 46 to 8
mls qos map cos-dscp 0 8 16 24 32 46 48 56
mls qos srr-queue output cos-map queue 1 threshold 3 4 5
mls qos srr-queue output cos-map queue 2 threshold 1 2
mls qos srr-queue output cos-map queue 2 threshold 2 3
mls qos srr-queue output cos-map queue 2 threshold 3 6 7
[code].....
Question 1:Why is the auto qos generated policed-dscp map different on these two switches?The Cisco Smart Business Architecture LAN configuration files guide [URL] does not specifically use the 3560 in their examples, they use the 3750 but it's my assumption that the same techniques, configs apply with regard to my specific feature questions. When using a 3750 in the Access layer, the guide shows (page 15) the same auto qos generated policed-dscp map configuration that is on my 2960. The SBA LAN config guide shows that when using a 3750 as a Distribution layer switch (page 26), the policed-dscp map configuration is the same that I see on my 3560.In the configuration guide for the 3750 distro switch, there is no auto qos applied as there are no access ports, so the mls qos commands are manually input. Since my 3560 does have access ports, auto qos generated the mls qos commands, and the results are the same be it following the guide and manually entering (per distro switch guidelines) or using auto qos. This leads to question 2...
Question 2:Why is the mls qos map policed-dscp configuration different depending on use as an access vs. distribution switch?
Question 3: On the 3560, access ports that have "auto qos voice cisco-phone" applied are put into queue-set 2 (output). Queue-set 2 (output) uses default values (not configured). Is this correct and desirable? If so, why? The 2960 has all ports in queue-set 1, regardless of being an access device port or a trunk port connected to the 3560 (as per the SBA LAN config guide EgressQOS macro commands). The 3560 trunk ports are all also configured to use queue-set 1 (output), again as per the SBA LAN config guide EgressQOS marco commands.
I have a few old 2600 routers (2621, different IOS's) which I'm now replacing for new one's from the 2900 series (2901, Version 15.1(4)M4).In my configuration I have two IP addresses in my LAN interface and I have HSRP configured within the secondary IP subnet range. It would be something like this:
interface GigabitEthernet0/1
ip address 172.x.x.x x.x.x.x secondary
ip address 10.z.z.z z.z.z.z
[Code].....
Now, in the new 2900 routers, my interface configuration hasn't changed however I can see that the hello packets are now sent with the source within the respective HSRP IP subnet so I had to edit my acl for that:
permit udp 172.x.x.x x.x.x.x host 224.0.0.2 eq 1985
Is there a way I can force the HSRP to work as it previously did in the old IOS's?
I have a 2900 router at branch office. This router has a 4 port switch card and two gigabyte ports. The gigabyte port is use for wan connection and the 4 port switch card is use for lan connection. I have two separate networks on my lan side. (network 1 and network 2)
I have assigned port 0,1 of the switch card to vlan1 for network 1 Ports 2,3 of the switch card is assigned vlan 20 for network 2
My problem is I would like to applied a bandwidth restriction for all data coming out from vlan20 capping same to 384 kb.
Note I do not want use QOS because this will only kickin when saturation occurs,
how to change the Baud Rate on Cisco 2900 SW utilizing ROMON ?
View 8 Replies View Relatedwe ordered a data e-delivery PAK L-SL-29-DATA-K9= (FOR A 2900 SERIES ROUTER) but after we received the PAK we discovered that the client actually has a 1900 router. Any easiest way of rectifying this mistake so that we can use the PAK on a 1900 series router?
View 1 Replies View RelatedTrying to apply this config to a 2900 router and getting this error message. [code] This works ok in in a 2800 router using 12.4(25d) spservices IOS
Not working on 2911 using 15.2(3)T2 ipbase image.