I need to do password recovery for a 2911 router. But ı can't find any documentation about it. I can be able to login at the first login, unfortunately ı logged out without changing the password. Now I can not log in and I can not open rommon with the ctrl+break key sequence.
View 6 Repliesi read alot about password recovery , but when i apply it to cisco 7604 it fails ?i went to rommon mode and typed# confreg 0x2142 then i typed reset when the router startup it request a password form me ,i can enter the user mode , and when i type sh ver command i note that the config resgitser is 0x2102 , not 0x2142 !!!!
i could enter the privilage mode !!!! and seems no thing changed ! does this router has a specific password recovery procedure ? which differes than the classic procedure?
I can see the console on the router. (Using the USB console connected to a Macintosh.) I was configuring the router though this console connection, and I created a new user (priv level 15) and removed the default 'cisco' user. So I'm stuck at the username/password login prompt now.
I decided to do the password recovery procedure (via the cisco doc I found etc), but I cannot break into ROMMON during the boot process. I'm not sure if that's because my Mac isn't sending the break, or what.
The pw recovery doc says you can "remove flash" if you can't break into the boot sequence. However, I cannot find any instructions on how to remove the flash. I've opened the router, and I see one very small daughter card on the main board that I think is the flash, but I'm not about to start arbitrarly prying parts off.
i need to recover a router Cisco 2801. I lost the password and the "no service password-recovery" is configured. I have done many attempts with the procedure in this link :URL
View 9 Replies View RelatedI am looking for a Cisco document that gives me the,IP through-put on 2901, 2911 and 2921 routers with Policy based routing applied.,IOS version 15.1.3TOther processes, EIGRP Stub, VLAN routing, SRST,MGCP gateway (analog and PRI).
View 1 Replies View Relatedis there any CEoIP modules (Such as NM-CEM-4TE1) for the 2900/3900 series routers?
View 2 Replies View Relatedwhat is the maximum number of Lan-to-Lan and user vpns supported in the ISR G2 2911 and 2921?
View 5 Replies View Relatedany place I can find how many tunes does the cisco 2900 series made? site to site?
View 1 Replies View RelatedI have a brand new 2901 and I'm trying to work out what licence features I have. The output of show licence shows I have ipbasek9 feature and datak9 as EvalRightToUse feature. Is BGP included in the base feature? What will happen when the datak9 evaluation period expires?
View 1 Replies View RelatedI have added 2900 series devices in LMS3.2.1 but same are showing "unknown"device Type in a report generated from common services DC R device List.
Both are snip enabled and responding too. What is the reason behind unknown device type so those are not reflecting in any module.
36.N007010101CRRUNKNOWN37.N007010103CRRCisco 2921 Integrated Services Router38.N007010201ASRUNKNOWN
I know we can use copy & Paste, my questions are:
1. Before that, do I need to wipe out the existing confi on the brand new switch?
2. About using TFTP, how does this new switch connects to the TFTP? Does it mean I have to assign a real IP and put it on our network?
We need to implement VLANs on my company's network. I have 3750 L3 swtich, ive setup 3 vlans for testing. ive setup SVI everything.now how do I connect it to 3com that will also use VLANs. should I set trunk port of cisco and 3com? or no need?
View 2 Replies View Relatedwhere I can find a CLI password recovery procedure for the administrator account?
View 1 Replies View RelatedI have problem recovering my cisco 501 pix password. I followed instructions on this pageurl... but it seems its not working. I cant ping my TFTP Server on my pc. I tryed to disable firewall on my pc, i did a fresh install Windows but still i cant ping my TFTP Server on my PC.
View 8 Replies View RelatedAs I make a password recovery to a Cisco PIX 525 Version 6.3(3)?
View 1 Replies View RelatedI just bought one of these in and it was in production and I have no way of getting a hold of the login information. Is there a way to wipe these to factory defaults? I have been looking everywhere with no such luck.
View 2 Replies View RelatedI am a student pursuing a CCNA certification currently. I recently came across a lot of 3548 xl switches. They power up fine, post with out problem and load flash. The problem I am running into is that the console is password protected. I have found the password recovery procedure for this switch, but it requires the use of the mode button. I have tried this process several times and the flash file is loaded with the startup config file. How do I perform a password recovery on a switch with a broken mode button?
View 1 Replies View Relatedhow to recover ACS 5.0.021 CLI password.I dont have 5.0.021 cd with me can i use 5.2 cd to recover the same ?
View 1 Replies View RelatedTo configure my Cisco, I use the console cable but as I have no serial port on my PC, I use a USB to serial cable which I plug the console. I had lost this USB cable -> serial but I found another one. So I started to configure my Cisco by copying from an existing config. I found out that a prior the converter is defective and copy the wrong config.
I had copied the enable secret password and it badly copied! No luck, I made a copy run start. Therefore more accessible to Cisco! When I start the Cisco, I see what activated "the Mechanism password-recovery is enabled". so I followed the procedure Cisco
I go flash_init: OK but when I type "load_helper" Unknown command it say to me .... I'm stuck!
The model is my Cisco: Cisco WS-C2960G-24TS-S
SW Version 12.2(55)SE3
Sw image C2960S-UNIVERSALK9-M
I have a couple of 877s which have "no service password recovery" set and something has happened to the flash or the IOS has been lost for one reason or another.
When trying to boot the routers, they all display similar to this, which then repeats:
[code]....
Or words to the effect of there being no IOS at all, unable to boot, but the result is the same, it just loops and there's nothing I can do to break the sequence!
I've tried taking the flash from a working 877 and replacing the card but this doesn't work and unfortunately, putting the once working strataflash card back in the working 877, it gets the same problem!
I have a cisco 515e pix but where I bought it from did not get the machine back to default. I boot it up and get to the user prompt, type enable and it asks for a username and then a password. I am new to this and am have no problems with router and switch password recoverys but when I look at the cisco documentation it is a bit overwhelming and I am not quite sure what it is that they want me to do to fix this. I have downloaded all the password recovery software loads and have the one I need for 6.x which is what the box is running I am just not sure what it is that I need to do. Can I use that recovery software from directly from my pc using a tftp server?
View 1 Replies View RelatedI need to recover switch enable password, i have already configured AAA also, when i am tryig to follow below proceedure finally saying Authorization failed. how can i recover enable password,If I try to recover password like this description says [URL]
Step 1 Connect a terminal or PC with terminal-emulation software to the switch console port.
Step 2 Set the line speed on the emulation software to 9600 baud.
Step 3 Power off the switch. Reconnect the power cord to the switch and, within 15 seconds, press the Mode button while the System LED is still flashing green.
Base ethernet MAC Address: 00:0x:xx:xx:xx:xx
Xmodem file system is available.
The password-recovery mechanism is enabled.
The system has been interrupted prior to initializing the flash filesystem. The following commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init
load_helper
boot
[code]....
where I can find a CLI password recovery procedure for the administrator account?
View 2 Replies View RelatedI was just configured a 3800 router with this command. I cannot get to the ROMMON mode anymore. Cisco says you should press Break key within 5 seconds after the image decompresses during the boot. But mine is ignoring it and going to load running config directly.
View 7 Replies View RelatedI have a 4404 running firmware 7.0 and something happened (don't think it was a hack), but all of a sudden I can't login to the box via web or ssh or even telnet.
In trying the recovery procedure, I get a lot of messages scrolling through and cannot do the Restore-Password command on the CLI.
I'm attaching the whole capture, but here's a truncated capture from the procedure:
*fp_main_task: Nov 21 10:39:46.501: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
*fp_main_task: Nov 21 10:39:46.501: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
[Code].....
So as you can see, my prompt to enter the command is taken up by this fp_main message and it uses up the first and only time I can enter this in. I'm trying everything I can to not have to go back to factory defaults.
How is-it possible to do a recovery password for sysadmin on ADE-OS ?We're using LMS 4.2.1 and my customer doesn't remember the username and password created during installation.We have the admin user for the https connection.
View 4 Replies View RelatedI wanted to do with my Cisco 2800, a password recovery. I have read the instructions and Cisco just came up at six.
Complete these steps in order to recover your password:
Shut down the router. Remove the compact flash that is at the back of the router. Power on the router. Once the Rommon1> prompt appears, enter this command:
confreg 0x2142Insert the compact flash. Type reset.
BUT I had forgotten to plug the flash card. And now comes via console hieroglyphics only
I have 3 x ASA 5510 & 2 x ASA 5520, that require resetting back to factory default, the customer has removed the External Flash Cards, and i've checked internally on each unit the Internal Flash car is still present, is it possible to run a password recovery then a factory reset? and how would i go about resetting each unit to the new configuration.
View 8 Replies View Relatedthe " password recovery functionality is disabled " service is running on the system .
im trying to access rommon in a Cisco 851, with not much success, i am sending a break after the image is loaded ( in the time frame that is allowed for that) .
I have a cisco PIX-515e which i have connected to a emulator through the console port, and im having trouble erasing data from it. I can get into 'pixfirewall' mode and 'monitor' mode but thats as far as i get. i have tried 'write erase' and 'configure factory-default' in both modes to no success.
View 11 Replies View RelatedI am studying for the CCNA and have my own lab. Several months ago I setup the lab and hand things running well, and decided to put it all away for a while. Alas, now that I have brought it all out again, I don't remember the passwords I used and have since destroyed my documentation, so this is perfect practice at password recovery/config maintenance type of stuff.
I am working on a 2610XM. When I power on the router, I see all the information pasted below. I have tried the password recovery processes described in the cisco knowledge base where we use the rommon prompt to load 0x2142, reset, then enable secret <password> and followed the remainder of the instructions, but when I reload the router after the process, the new password I've set still does not work.
Some things that are not consistent from the documentation that I am seeing are the messages Slot is empty and WIC is empty.
I am wondering if my router does not use 0x2102 for it's load, but it will not show what it is using and I can't run show version because of the password. I am connecting through the console port and using putty to access and configure. Below is a paste of the startup messages after the router decompresses it's image.
Processor board ID JAD070709N9 (1997350087)
M860 processor: part number 5, mask 2
Bridging software.
[Code].....
how to password recovery Wireless LAN Controller 4402
View 3 Replies View RelatedI am trying to use the password recovery for an NME-16 and am having trouble. I am unable to look at my files in dir to so I can rename them. I can get the switch to bypass the config and come with the switch: prompt, but can not do anything more. I am trying the password recovery guide, but cant get to the text file to rename. I am using a 2811 router.
View 2 Replies View Related