Cisco Switching/Routing :: Password Recovery On 1900 Series ISR?
Jan 1, 2012
I can see the console on the router. (Using the USB console connected to a Macintosh.) I was configuring the router though this console connection, and I created a new user (priv level 15) and removed the default 'cisco' user. So I'm stuck at the username/password login prompt now.
I decided to do the password recovery procedure (via the cisco doc I found etc), but I cannot break into ROMMON during the boot process. I'm not sure if that's because my Mac isn't sending the break, or what.
The pw recovery doc says you can "remove flash" if you can't break into the boot sequence. However, I cannot find any instructions on how to remove the flash. I've opened the router, and I see one very small daughter card on the main board that I think is the flash, but I'm not about to start arbitrarly prying parts off.
View 6 Replies
ADVERTISEMENT
Oct 15, 2012
I've got a problem with DHCP running on a cisco 1900 series router, 1921 to be precise. The Data VLAN works perfectly, i configured a ip helper address and its working. Problem tough is VLAN 20. This is the voice vlan. As u can see in the config below, this has been configured using VRRP and VRF for failover purposes. I did more of these configurations, and they all worked fine, just not with this particular router!
As u will notice i deleted all the not needed to know information or i X'ed it!
Jan-Aart
version 15.1
service timestamps debug datetime msec
[Code]......
View 3 Replies
View Related
Jan 1, 2013
i have a cisco 1900 series router from the isp and we connect it the our router the rv042 small biz, and we have here a cisco catalyst 2950 switch with just default configuration connected to the hosts.
my problem is from time to time that the connection is lost there is no connection with the router and the only solution is to turn off and on the cisco 1900 router and the connection will be back.
do we need to configure the routers and switches? what do you need to configure?
View 2 Replies
View Related
Feb 10, 2010
I need to do password recovery for a 2911 router. But ı can't find any documentation about it. I can be able to login at the first login, unfortunately ı logged out without changing the password. Now I can not log in and I can not open rommon with the ctrl+break key sequence.
View 6 Replies
View Related
Sep 17, 2012
I am trying to use the password recovery for an NME-16 and am having trouble. I am unable to look at my files in dir to so I can rename them. I can get the switch to bypass the config and come with the switch: prompt, but can not do anything more. I am trying the password recovery guide, but cant get to the text file to rename. I am using a 2811 router.
View 2 Replies
View Related
Sep 24, 2012
I want to recover the password or set the cisco 3750 to the default password, as forget it
View 4 Replies
View Related
Feb 19, 2013
Currently Being Moderated password recovery
View 3 Replies
View Related
Apr 7, 2012
i just wanna know if it's possible to perform a router password recovery using the reload command and then issue the break sequence instead of doing an off/on on the power switch. i often find in the docs to use the latter.also, is there a way to retain the startup-config on a router when we re-enable the password recovery functionality (no service password-recovery). i've just tried this on one of our 877 and when i hit the break sequence, it went back to factory default setting.
View 7 Replies
View Related
May 20, 2010
I understand that the password has to be changed the first time we login to Cisco 3945 router but i failed to do that and its not allowing me to connect using default username/password.
View 7 Replies
View Related
May 16, 2010
I have one CISCO 6509 Switch in my store. I tired to login in that switch but couldnt.. Once it's booted it's asking me: rd: . Find the attachment. I recover the password by changing confreg value but that also failed.
View 8 Replies
View Related
Feb 18, 2013
I need to break into a 2901 router to recover the passwords. Cisco's methodology for password recovery on 2900 seriews routerssays to remove the compact flash card and reboot into RMON. There is no external compact flash card on a 2901. Is there acompact flash card inside the box? Or can you use the older method of rebooting and then hitting ctl+break to boot into RMON?
View 5 Replies
View Related
Oct 5, 2011
I have a major problem with our core 2801 router. In summary it appears that a staff member disabled password recovery, deleted the IOS and rebooted. Net result is no Rommon and no IOS on the flash. I've read that the Conf-Reg will be reset if I remove the NVRAM but I cannot identify it on the board. If I can get to Rommon I can recover. Currently I don't have Flash reader to restore to flash.
View 2 Replies
View Related
Dec 5, 2012
I'm using the ctrl-break sequence in hyperterminal during the the initial boot, and it's hanging.
View 1 Replies
View Related
Jul 14, 2012
i read alot about password recovery , but when i apply it to cisco 7604 it fails ?i went to rommon mode and typed# confreg 0x2142 then i typed reset when the router startup it request a password form me ,i can enter the user mode , and when i type sh ver command i note that the config resgitser is 0x2102 , not 0x2142 !!!!
i could enter the privilage mode !!!! and seems no thing changed ! does this router has a specific password recovery procedure ? which differes than the classic procedure?
View 4 Replies
View Related
Oct 31, 2011
I have catalys 4507 with TWO supervisor V.I flowed this procedure : url...
after the reset normaly i can change the password and i check the confreg is 0X2142 but it still ask to enter the possword should i remove 1 supervisor and do the procedure or i must let the two spuervisor?
View 2 Replies
View Related
Sep 7, 2012
I have 2 x 6513 each with dual supervisor 720, and need to recover the enable password, is there a better method than removing one supervisor, disabling redundancy and performing password recovery on the single active supervisor module , before re-inserting the second supervisor and re-enabling SSO/RPR on the still active module.
View 2 Replies
View Related
Dec 21, 2011
Following procedures get to the switch: dir flash and get the following.....unable to stat flash//: no such device
View 4 Replies
View Related
Nov 5, 2012
Im trying to access the switch to reset the password to factory defaults (please see switch output Astrix has removed customer identifying information for security purposes.) Each time I reboot the switch and try and access the password recover mode this same output below starts and im still not able to access the recovery area of the switch
cisco WS-C3560G-48PS (PowerPC405) processor (revision F0) with 122880K/8184K bytes of memory.
Processor board ID FOC1133Y28Q
[Code].....
View 3 Replies
View Related
Feb 9, 2012
I enabled the "no service password-recovery" command on my C2960 switch. All seems to work as discribed. Only issue I have is --- which show command is used to reveal if the password-recovery feature is enabled of disabled as the command doesn't show up in the running config after you enable it ?
NOTE: The command does show up in the C2960 switch in config t mode (unlike the IOS router 2800 series), but doesn't show up in the running-config after you enable or disable it.
On the 2800 series routers (latest IOS) in config t mode the command does not show up but if you type "no service passowrd-recovery" the command function correctly and it does list it in the running configuration.
View 1 Replies
View Related
May 1, 2012
i need to recover a router Cisco 2801. I lost the password and the "no service password-recovery" is configured. I have done many attempts with the procedure in this link :URL
View 9 Replies
View Related
Jan 20, 2009
how do i recover username and password for 870 series router
View 5 Replies
View Related
Oct 7, 2012
I bought 1921-SEC-k9 so i have security license installed: Technology Package License Information for Module:'c1900' [code] Now I'd like to know if SSL VPN comes with that license or do I need to buy additional VPN SSL license to use it? If so.. i'd just use IPsec... i need client-to-site configuration.. can you point me to tutorial or just a basic config.. because for ipsec i just find site-to-site tutorials on internet.
View 8 Replies
View Related
May 3, 2011
Sure this is a simple one. New to the 1900 series routers, have a 1921 with IOS 15.1. Noticed that there is a standard interface labeled Embedded-Service-Engine0/0. What the purpose of this is? Cannot seem to find any detail on it. See extract from default config below.
View 5 Replies
View Related
Oct 30, 2011
Is there a router (1900-3900 series router) that will support a 100FX fiber connection. We use to use 2800-3800 and 2600-3700 series routers with FX fiber interface now these routers are no longer available and our need for 100Mbps FX is still a requirement.
View 3 Replies
View Related
Oct 3, 2012
I'm a bit new to Cisco and i find this AAA a bit confusing..I've turend on AAA by:aaa new-model
Can I use this "default" list for WebVPN ? And what would be a different if i create new "sslvpn" list..Also when I'll be creating user for VPN remote access.. that user will also exist in local database and have access to router via SSH?Because the research I've done it doesn't seem you can group users in different "aaa groups" e.g. user admin belongs under "admin" aaa group which can do ssh to router, users for VPN can only do remote VPN access and not SSH and login into router.i saw ASA has some attribute for users called remote-user
•admin, in which users are allowed access to the configuration mode. This option also allows a user to connect via remote access.
•nas-prompt, in which users are allowed access to the EXEC mode.
•remote-access, in which users are allowed access to the network.
But i can't find this option in IOS on my 1900 Series ISR router.
View 1 Replies
View Related
Jan 8, 2013
We have been using a dhcp and tftp server to automatically configure branch WAN routers such as 1751's and 1841's for years but, have recently purchased a 1921 and 1941 as possible next generation replacements. The problem is when the 1900 series power up instead of getting a dhcp address directions to the tftp server it boots up and asks for the user name to be immediately changed or you will be "locked out". Any workaround to this so that I can again go back to download my common configuration? Or any other way of automatically configuring the newer version ios? Doing extra steps for 500 WAN branch routers is time consuming. Doing configurations without automation for that many is moving in the wrong direction.
View 1 Replies
View Related
Jan 8, 2012
I've been implementing a setup where a remote office has a Cisco 1900 router. There are 2 GRE/ IP SEC tunnels to the headquarters, 1 over public internet, 1 over a private cloud. Because of some MTU issues we have to clear the DF bit for some of the traffic, but we also want to use PBR to send https traffic over the "public internet" tunnel and the rest of the traffic over the "private cloud" tunnel. I'm able to clear the DF bit and to do the PBR with route-maps, but I'm not able to implement both functionality at the same time.
View 1 Replies
View Related
Apr 29, 2013
How to get the Snmp OID for polling the in and out utilization for the CIsco 1900 Series Router interfaces.
View 1 Replies
View Related
Feb 1, 2013
i have a cisco catalyst 1900 & i like to share internet among 15 PC in my lab they all are connected to the switch through a patch panel should i connect my ADSL Modem to the switch, the switch is running on default config.
View 6 Replies
View Related
May 15, 2013
we ordered a data e-delivery PAK L-SL-29-DATA-K9= (FOR A 2900 SERIES ROUTER) but after we received the PAK we discovered that the client actually has a 1900 router. Any easiest way of rectifying this mistake so that we can use the PAK on a 1900 series router?
View 1 Replies
View Related
Apr 24, 2013
I am troubleshooting memory leaks and buffers issues on my 1900 and had some doubts regarding the problems that my router causes.Intermitently during the day for no reason the gig0/0 interface connected to ISP stops responding from our management network (log shows that the interface goes down). The ISPs modem responds fine from my management network.The issue goes away by itself in 20 minutes, sometimes more or after a hard reboot.Sometimes a router would increment a throttle value to 1. When running for 4 days without a reboot, the router raised 39 throttles and 57 input drops. [code] The router is running Version 15.1(2)T4 and I was not able to find any caveats on cisco web page (although I havent used the bug finder tool)Is this only leak I found a reason to start worrying or I can disregard it and continue basic troubleshooting (change cable and plug my ISP to another port)
View 3 Replies
View Related
Sep 1, 2012
I setup a GRE tunnel between two cisco 1800 & 1900 routers. I can't received multicast.
Here is a copy of my configs:
R3#Building configuration...
Current configuration : 1238 bytes!version 12.4service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname R3!boot-start-markerboot-end-marker!logging message-counter syslog!no aaa new-modeldot11 syslogip source-route!ip cefip multicast-routing no ipv6 cef!multilink bundle-name authenticated!archivelog config hidekeys! interface Loopback0ip address 10.0.0.3 255.255.255.255!interface Tunnel0ip address 192.168.24.2 255.255.255.252ip pim sparse-modetunnel source Loopback0tunnel destination 10.0.0.1!interface FastEthernet0/0ip address 10.0.3.1 255.255.255.0ip pim sparse-modeduplex autospeed auto!interface FastEthernet0/1ip address 192.168.23.2 255.255.255.252ip pim sparse-modeduplex autospeed auto!interface Serial0/0/0no ip addressshutdownno fair-queueclock rate 2000000! router eigrp 1network 10.0.0.3 0.0.0.0network 10.0.3.1 0.0.0.0network 192.168.23.2 0.0.0.0no auto-summary!ip forward-protocol ndno ip http serverno ip http secure-server!control-plane!line con 0line aux 0line vty 0 4exec-timeout 5 0privilege level 15no login!scheduler allocate 20000 1000end
[code]....
View 3 Replies
View Related
Jan 15, 2012
I had to format flash and recover. I did the quicker way by using set BAUD 115200...once the .bin was across I forgot to set the baud back to 9600. I have followed instructions: go back to switch: set BAUD 9600 then reset. also tried the unset command. problem is it always comes back up with a BAUD of 115200. CWill I have to label 1 switch as 115200?
View 38 Replies
View Related
