I bought 1921-SEC-k9 so i have security license installed: Technology Package License Information for Module:'c1900' [code] Now I'd like to know if SSL VPN comes with that license or do I need to buy additional VPN SSL license to use it? If so.. i'd just use IPsec... i need client-to-site configuration.. can you point me to tutorial or just a basic config.. because for ipsec i just find site-to-site tutorials on internet.
View 8 RepliesI can see the console on the router. (Using the USB console connected to a Macintosh.) I was configuring the router though this console connection, and I created a new user (priv level 15) and removed the default 'cisco' user. So I'm stuck at the username/password login prompt now.
I decided to do the password recovery procedure (via the cisco doc I found etc), but I cannot break into ROMMON during the boot process. I'm not sure if that's because my Mac isn't sending the break, or what.
The pw recovery doc says you can "remove flash" if you can't break into the boot sequence. However, I cannot find any instructions on how to remove the flash. I've opened the router, and I see one very small daughter card on the main board that I think is the flash, but I'm not about to start arbitrarly prying parts off.
Sure this is a simple one. New to the 1900 series routers, have a 1921 with IOS 15.1. Noticed that there is a standard interface labeled Embedded-Service-Engine0/0. What the purpose of this is? Cannot seem to find any detail on it. See extract from default config below.
View 5 Replies View RelatedIs there a router (1900-3900 series router) that will support a 100FX fiber connection. We use to use 2800-3800 and 2600-3700 series routers with FX fiber interface now these routers are no longer available and our need for 100Mbps FX is still a requirement.
View 3 Replies View RelatedI've got a problem with DHCP running on a cisco 1900 series router, 1921 to be precise. The Data VLAN works perfectly, i configured a ip helper address and its working. Problem tough is VLAN 20. This is the voice vlan. As u can see in the config below, this has been configured using VRRP and VRF for failover purposes. I did more of these configurations, and they all worked fine, just not with this particular router!
As u will notice i deleted all the not needed to know information or i X'ed it!
Jan-Aart
version 15.1
service timestamps debug datetime msec
[Code]......
I'm a bit new to Cisco and i find this AAA a bit confusing..I've turend on AAA by:aaa new-model
Can I use this "default" list for WebVPN ? And what would be a different if i create new "sslvpn" list..Also when I'll be creating user for VPN remote access.. that user will also exist in local database and have access to router via SSH?Because the research I've done it doesn't seem you can group users in different "aaa groups" e.g. user admin belongs under "admin" aaa group which can do ssh to router, users for VPN can only do remote VPN access and not SSH and login into router.i saw ASA has some attribute for users called remote-user
•admin, in which users are allowed access to the configuration mode. This option also allows a user to connect via remote access.
•nas-prompt, in which users are allowed access to the EXEC mode.
•remote-access, in which users are allowed access to the network.
But i can't find this option in IOS on my 1900 Series ISR router.
We have been using a dhcp and tftp server to automatically configure branch WAN routers such as 1751's and 1841's for years but, have recently purchased a 1921 and 1941 as possible next generation replacements. The problem is when the 1900 series power up instead of getting a dhcp address directions to the tftp server it boots up and asks for the user name to be immediately changed or you will be "locked out". Any workaround to this so that I can again go back to download my common configuration? Or any other way of automatically configuring the newer version ios? Doing extra steps for 500 WAN branch routers is time consuming. Doing configurations without automation for that many is moving in the wrong direction.
View 1 Replies View Relatedi have a cisco 1900 series router from the isp and we connect it the our router the rv042 small biz, and we have here a cisco catalyst 2950 switch with just default configuration connected to the hosts.
my problem is from time to time that the connection is lost there is no connection with the router and the only solution is to turn off and on the cisco 1900 router and the connection will be back.
do we need to configure the routers and switches? what do you need to configure?
We have ASR 1006 with IOS XE and i want to see the Software License but somehow i cant!!! ...i googled it but i could not find anything.how can i see the available license on ASR 1006 or 9000 series?
View 1 Replies View RelatedI have a brand new 2901 and I'm trying to work out what licence features I have. The output of show licence shows I have ipbasek9 feature and datak9 as EvalRightToUse feature. Is BGP included in the base feature? What will happen when the datak9 evaluation period expires?
View 1 Replies View RelatedI bought a 5500 series ASA and SecPlus license for example. Suddenly my ASA hardware got broken and changed for a new one. What about my old license? How i could activate this license on new ASA?
View 2 Replies View RelatedWhat's the difference between VPN Plus license and Security Plus license. I have new 5520 shipped with VPN Plus license.Also does it require a seperate license for Anyconnect for Mobile and AnyConnect Essentials.
View 1 Replies View RelatedI’m stuck in some problem with installation of LMS4.0 in customer site.
- we purchase a LMS4.0(CWLMS-4.0-100-K9) but couldn’t install it on Windows server 2008 R2 64bit because those things don’t support each other.
- I need to upgrade the LMS4.0 to LMS4.2 that is supporting Windows server 2008 R2 64bit.
- So, I ordered following items via product update tool (url...) [code]
- In this status, how to install LMS4.2 with license for 100 devices? If I install R-PI12-BASE-K9 first, can i enter a licese for 100 devices for CWLMS-4.0-100-K9 into PI1.2?
I have a client whom uses a DSL 10 MG circuit as their backup circuit for Internet Connectivity in case of a failure. The circuit uses a DSL modem that is unreliable. I was recommending yesterday tot he client that perhaps we could place a Cisco router in place of the residential grade DSL modem /router currently in place.I wanted to place a 1900 ISR G2 in there, which would allow me to swap the DSL module out whenever I can talk the company into a Metro E connection. At that point I could swap the DSL module out and put an Ethernet module in to receive the Metro E. I was not able to find a solution last night using the Dynamic Configuration Tool. Seems DSL has been phased out.Is there any recommendation that could be made to accommodate this clients request for a Cisco router that will handle DSL?
View 7 Replies View RelatedI have a new ISR 1900 router on which i accidently deleted the default username and password and now i am unable to get in to router console. Also i am unable to break in to Rommon mode as well.
View 2 Replies View RelatedWe've just bought Cisco 1900 series, we encounter a few problems
1- The IOS version is different from our previous router. Previous version is 12.4 , our new router is version 15.1
2- Below is our previously working config for controller . The channel group must be unframed
!
controller E1 0/0/1
channel-group 0 unframed
!
3- Hoewever the config below is from our newly bought 1900 series IOS ver 15.1 . However they do not support unframed format.
!
controller E1 0/0/0
channel-group 0 timeslots 1
!
We are using Cisco 1941 Router as CPE where we wanted to trap CPU, Memory & ISYSTEM MIB. The same we are achiveing using SNMPV2 but when we tried using SNMPV3, there is no response for these MIBs.
We tried to configure SNMPV3 using below Link but still there was issue. There was response fr [URL]
Wanetd to know SNMPV3 MIB are supported for Cisco 1941 Router IOS Code universalk 15.2(3)T1 & Data License. When we tried using Cisco IOS MIB Locator, we are not able to see any MIB for SNMPV3. whats is that mean. Does this Platform + IOS Support SNMPV3 or not.
Below is the Snapshot from Cisco IOS MIB Locator for said image.
[Code]......
interface GigabitEthernet0/0
ip address x.x.x.36 255.255.255.248
ip nat outside
ip virtual-reassembly in
no ip route-cache
duplex auto
speed auto
no cdp enable
[Code]
ip nat inside source static tcp 192.168.1.252 22 x.x.x.36 6922 extendable
ip route 0.0.0.0 0.0.0.0 x.x.x.33
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 1 permit any
Anything wrong with my config? port forwarding to my ssh wont work. Im using CISCO 1900 Series.
We have about 9 1900 routers and 1 ASA 5510 for partail mesh VPN network. So 8 1900 connect to 1 1900 and ASA located in HQ and datacenter. All worked well however there is one site running really strange. The tunnel between 1900 is up for a while and down. Reboot router seems to be the only fix. But tunnel to ASA does not seem to be down at all.
The issue happened again today, we rebooted the router on site but tunnel still not up. DEBUG shows: deleting SA reason "Death by retransmission P1 "
I can see alot of Apr 24 19:57:55.271: ISAKMP:(0): retransmitting phase 1 MM_NO_STATE...
To me it seems like the IDE packet sent but never got reply and timed out. I did also check on the other end, the HQ. All other tunnels are still running fine on that router, just this remote site. Plus I got the similiar output when debugging on HQ router.
One thing do notice though, there was no match on both router for the ACL to match/permit ESP traffic... I asked on-site staff to reboot the modem used in remote site.
Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies View Relatedwhy I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedWhat's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies View RelatedMy Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies View RelatedDoes AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replies View Relatedi cant get access to my router IPX1900 after upgrade the last firmware version?
View 3 Replies View Relatedif I have made a simple mistake with my config. It has authenticated ok and been assinged an Internet IP address from the ISP but the clients can not connect ping any internet address nor can the router.
hostname
!boot-start-markerboot-end-marker!!enable secret 5 $1$WGr1$khNrjiwYANhUsIaKEBDsL0enable password 7 121A0C041104!no aaa
[Code].....
We have Cisco 1900 Series Integrated Services Routers (has a wired router and a wireless router) and since this morning we can not send emails.I inquired with both the ISP and the hosting provider and all settings are correct.I can receive emails from outside the router, but can't send any emails out.If I try to telnet mail902.opentransfer.com 25 it doesn't connect.Port 25 is the port we were using all the time and was working through the router.I connected my laptop directly to the modem and was able to send emails using port 25, also was able to telnet to outgoing mail server. I didn't change anything in the router.is there a way to "enable" port 25 or "enable" mail.homeserviceclub.com (smtp server) or mail902.opentransfer.com (hosting mail server) if this would solve the problem?I don't understand why is this happening as I never had to enable or disable any email ports or mail server addresses.
View 3 Replies View Relatedi have one airtel isp connection was connected to beetel adsl modem and this modem is connected to d-link switch to accessing internet for my lan. and one netgear wireless router is aslo connected to this d-link switch. my need is i has one cisco 1900 router, i want to get internet access from adsl modem or netgear router to my cisco router.
View 1 Replies View RelatedToday I was having a conversation with my Cisco Academy teacher from a few years back, and we couldn't figure this out.I am getting an internet connection via Verizon FiOS. Instead of giving me an ISR, they're going to just give me an ethernet cable. Here's what I want to do with it.
This cable is going to be plugged into a 1900 series router. Connect to that will be a 48 port switch. Connected to that will be multiple servers to be used for web hosting, email, databases, etc. My ISP is providing me with 13 public addresses, however, it is not my own unique subnet.
Here comes the question; how would I set this up? The way I was originally thinking was to assign one IP to fa0/0, a second to fa0/1, and then assign the fa0/1 address as the default gateways for all the hosts on the inside. But then I realized that it won't let me have the same network on 2 ports.
Sometimes our network lag and i thing there is a computer making this problem. i'd like to audit all input output of all port of a Catalyst 1900. all i manage to do is to enter to the console menu via Telnet.. once here, i try monitoring but i'm afraid to do a bad thing :
Catalyst 1900 - Main Menu
[C] Console Settings
[S] System
[N] Network Management
[P] Port Configuration
[Code]...
My customer is looking at using routers in DMVPN remote locations as DNS servers. He would like to be able to estimate how much memory the DNS cache will consume before going into production. I know you can get cache information when it's running, but he wants to plan ahead.I couldn't find any reports in Cisco or on the web of DNS caching causing memory issues, so I don't think he has much to worry about, but any rule of thumb as to how much memory each cache entry consumes would be useful. Or is there a protection mechanism to limit cache memory size in IOS ? The routers will be 877s and/or 1900-series.
View 0 Replies View RelatedI need to find an iOS version that supports BGP, Dot1q, and MPLS for either a 1800 series or 1900 series not sure the best place to find this sort of info out.
View 1 Replies View Relatedi just want to administor cisco ASA5520 and cisco router mpls 1900 can some tell me as admin what to check as u get into office /reguraly in cisco asa 5520 and vpn mpls router for administrator ,right now its working as configured by supplier for remote sites to connect HQ and access several server,My interest to know what are the basic day to day checkup on cisco asa5520 working as ips and cisco asa 5520 working as content filtering and cisco vpn mpls
View 2 Replies View Related