i have one airtel isp connection was connected to beetel adsl modem and this modem is connected to d-link switch to accessing internet for my lan. and one netgear wireless router is aslo connected to this d-link switch. my need is i has one cisco 1900 router, i want to get internet access from adsl modem or netgear router to my cisco router.
View 1 Replies
I have a problem connecting wifi router(airlive wt-2000r) to my ADSL modem(webstar epc2203ed2.0) using utp patch cable. When my PC is connected straight to the ADSL modem everything works like charm. But when I connect modem with wan port on the router and router with my PC I get no internet access. The network shows as unidentified network and win7 troubleshooter says: Default gateway not available. Connecting them two devices seems pretty simple and I dont think I am doing anything wrong so what could be the problem?
View 1 Replies View Relatedif I have made a simple mistake with my config. It has authenticated ok and been assinged an Internet IP address from the ISP but the clients can not connect ping any internet address nor can the router.
hostname
!boot-start-markerboot-end-marker!!enable secret 5 $1$WGr1$khNrjiwYANhUsIaKEBDsL0enable password 7 121A0C041104!no aaa
[Code].....
The ADSL Modem CISCO867-K9 is not connecting to our NAS router with default mtu value in the NAS router virtual template
Is there is any reason for ths ? With the below settings my ADSL 867 connecting , but if i remove the (mtu 1440 and ip tcp adjust-mss 1392 , this modem is not connecting
My Virtual Template config
interface Virtual-Template1
mtu 1440
ip unnumbered Loopback3
[Code].....
Dear The ADSL Modem CISCO867-K9 is not connecting to our NAS router with default mtu value in the NAS router virtual template.With the below settings my ADSL 867 connecting , but if i remove the (mtu 1440 and ip tcp adjust-mss 1392 , this modem is not connecting. [code]
View 2 Replies View Relatedi have a problem with my adsl line connected on a HWIC-ADSL on router 2901 it was working good until yesterday the atm interface is down but the interface dialer is up .i connected this line into home adsl modem and the line is working good?
View 2 Replies View Related! have a TELSTRA ADSL wireless router ( Thomson TG782T)I need to connect my 2 printers to it so I can operate them wirelessly to my laptop and Desktop computers
Laptop: TOSHIBA Satellite w/- windows 7 Professional
Desktop: ASI Computer w/- Windows 7 Ultimate currently connected to ADSL modem by yellow network cable.
configuring my new Cisco 881 Router with my existing ADSL modem.At the moment, i am connecting to the internet using tp-link modem router, all PPPoE/DHCP/Wireless is set up there...and that connect to the switch where all my computer connected to.
Now i want to connect this new Cisco Router to it to basically do the firewall/filtering/dhcp...leave the authentication thing on my Modem.Can i get a head start what to configure here on the cisco? since it does not work as easily as other Router where I can just plug a cable from modem LAN to Router LAN.
I want to transfer files between two computers.i have a Router+Adsl modem i want to network two pc one is running windows xp and other is running windows 7.i plug both pc's cable in Router and LAN card...after that my network places shows below picture i didn't configure anything. url...when i click other network pc it ask me user name and password. url...I never did networking. how can i transfer files between two pc's while internet don't stop.
View 2 Replies View RelatedA Layer 2 switch with IP Address 192.168.1.4 (Vlan0), subnet 255.255.255.0 is physically connected to ADSL Router with IP address 192.168.1.1 (which is also the gateway address for the switch). The problem I have is that all the devices connected to the switch can intercommunicate but are unable to communicate with devices connected to the Router. I guess this may be something to do with how the Vlan is configured on ADSL router?
View 1 Replies View RelatedMy desktop however, does not have built-in wireless and therefore would have to connect to the ADSL router (Netgear) through ethernet but this cannot be done as the router must remain in my bedroom, much too far away for cables to reach.I bought a USB wireless connecter for the desktop but it doesn't seem to work. It connects but gives "Local Only" as the connection.
View 9 Replies View RelatedI am looking to purchase an ADSL wireless modem router combo which will be mainly used for net browsing, online gaming (ps3) and skype.It has been suggested by the IT tech we use that I a get dual band n wireless gigabit modem/router but my limited knowledge and the confusion created by reading multiple contracting reviews of products is sending me a bit loopy.
View 2 Replies View RelatedModem/router mac address changer .. i have globe wimax bm622i model, that needs to be change its mac address, hardly to find a right software, so i decide to manually config and do it by ms-dos commands, any related command for dos to change mac address of globe-wimax-bm622i-model.
View 1 Replies View RelatedI'm expanding my home network and the adsl modem router supplied by my ISP has just 1 RJ-45 port and 1 usb port (and an RJ-11 for the Internet). I have zeroed in on TP-Link TD-W8901G having 4 RJ-45 ports, 1 USB port, 1 RJ-11 port and also it is a wireless router. Currently I would be connecting the above modem router to my desktop running Linux and using the same ISP with ADSL. Considering a future scenario where I may decide to use another way to connect to the Internet like maybe 3G or Cable, etc (with their separate modems) I was wondering if my same modem router (TD-W8901G) could be used as a standalone router for connecting the devices on my home network. Basically, what I want to know is whether this modem router would be able to share an Internet connection from some other source, other than the one provided through its own RJ-11 (ADSL) source?
View 1 Replies View RelatedI've a Shiro DSL805E Modem and to connect to multiple computers, I connected an Encore 5 Port Switch. Now I got laptop and thought of getting a wireless network, so I bought TP-Link TL-MR3420 Wireless Router and connected it to the one of the wires from the Encore Switch. But I'm unable to access the internet through TP-Link Router but the internet works fine for the computers which are directly connected to switch. how to do ip settings for TP-Link Router. But when I connect router directly to modem by bypassing switch, it works fine but not via switch. I have some restrictions due to which I have to strictly following this sort of connection: Modem -Switch - Router
View 1 Replies View RelatedRegion : UnitedKingdom
Model : TL-MR3220
Hardware Version : Not Clear
Firmware Version :
ISP :
I am connected to the internet via a non TP=Llink ADSL2 modem/router supplied by my ISP.I was using my TL-MR3220 as a 3G modem but no longer need it for that purpose. I was wondering whether I can now use my TL-MR3220 for two other purposes: as an additional wireless access point and as a means of linking equipment (i.e. printers) to the home network . i have tried connecting the ADSL2 modem/router to the TL-MR3220 via an ethernet cable (one of the 4 LAN ports on the ADSL modem/router to the blue WAN port on the TL-MR3220) but I can get no internet connection through the TL-MR3220.Is this normal i.e. something that the TL-MR3220 is not designed to do, or am I just using the wrong settings ? I have tried a whole range of different settings but none seem to work.
We currently have a main network running through a static broadband connecting using a Cisco 1700 ADSL router, everything is working fine locally.
We are looking to rent some space in an office nearby so im going to order another business adsl connection with static IP for this site and i currently have a spare 1800 router.My question is can the cisco routers connect up like a VPN connection so both sites work together and will the connection remain online constantly so from the remote office we can access all our servers from the main network?
Also how does the IP addressing work on 2 sites. The main network uses 10.120.21.x and DHCP is assigned from a cisco router. Does the remote network assign from the same DHCP server or would the remote sites cisco router need to be setup to give out DHCP to local machines. If so what would be the best IP setup to use.
I have a Wimax internet connection via an ethernet cable from a small roof top receiver dish. Inside the house the cable (RJ45) is plugged into the POE slot on one side of a small electrically powered black box, and from the other side, an ethernet cable (RJ45), connects to my PC. I want to share my internet connection with my HTC mobile and would prefer to make use of an existing Belkin 54g ADSL2 modem/wireless router (Belkin F5D7633) if I can. As this router's incoming port is specifically for ADSL my internet RJ45 cable can not plug into it. I have been advised that I can still utilise the router part of the Belkin though, using my PC as an access point, by plugging the ethernet cable from the PC side of the little black box into LAN 1 on the router, then joining the PC to LAN 2 of the router with another ethernet cable.I did not alter the configuration of the Belkin at all (having reset factory defaults beforehand), mainly because although I could access the internet from my PC and my mobile, I could not access the IP address of the router, presumably because the properties of the local area connection on my PC remained unchanged with the IP address (172.168.1.149), Subnet Mask (255.255.255.0), Default Gateway (172.168.1.1) and 3 DNS addresses (172.168.1.1) (10.30.0.1) (8.8.8.8) as they were before hooking up the Belkin. The IP address the mobile received through WIFI on connecting to the Belkin was 172.168.1.148
I was not unduly concerned about not being able to access the configuration of the router as everything was working as I had hoped it would and even when I powered off my PC I still had internet access on my mobile. On rebooting the PC, however, I found that the router changed the DNS addresses on the PC to 2 only, both identical (192.168.2.1) and the IP on the mobile was allocated 192.168.2.2 Although I could still access the internet on my PC, I no longer had access from my mobile although the WIFI connection to the Belkin showed as being 'excellent'. When I did a 'repair' of my internet connection, hoping to revert to a fully operative state, the PC configuration changed again as follows: IP address becomes that of the router (192.168.2.1), Subnet Mask (255.255.255.0), Default Gateway (192.168.2.1), 2 DNS addresses (192.168.2.1) and the IP address allocated to my mobile remains (192.168.2.2) This configuration means I have no internet access from either PC or phone, but CAN access the router configuration. I restored a usable operating state by unplugging the power from the router, transposing the cables in the LAN ports on the router (swapped cable from LAN1 to LAN2 and vice versa), turned off WIFI on mobile and waited a minute or two. When I powered the router back up and switched on mobile WIFI again, everything was restored to the original working state and I have, once again, access to internet on both PC and mobile. It is very frustrating, however, to keep performing this ritual and I wonder if any of you more technically minded, know a way to work around this, perhaps by manually changing the configuration of PC or router?
I am trying to connect a wireless router (EDIMAX br-6228nc) with a ADSL router (NETGEAR). i assigned the LAN IP of the ADSL modem to 192.168.1.1, subnet mask 255.255.255.0, and enable DHCP server.then i connected a LAN port from ADSL router to the WAN port of the wireless router. i assigned IP of the WAN port of wireless router to 192.168.1.10, subnet mask to 255.255.255.0 and default gateway to 192.168.1.1 now on the LAN side of the wireless router i assigned IP 192.168.0.1 and subnet mask 255.255.255.0 enabling DHCP server.on the client pc i selected the setting of automatically assign IP setting (which it got 192.168.0.100, default gateway 192.168.0.1) but my client pc is not able to access the internet.
View 2 Replies View RelatedWe got a 1921 router that works fine. We ordered Verizon Businss One Static IP ADSL. It came with a Westell Modem that we configured in bridge mode. When we do a test by assigning a static IP to our laptop then hook it up to the Westell it works fine. We can browse the web. Then when we assign a static IP to the Ethernet on our 1921 then connect it to the Westell it doesn't work. We can't ping out from the router to for example 4.2.2.2. From the router we can't even ping the default gateway (on Verizon's side).
View 2 Replies View RelatedWe have a Vigor ADSL modem linked to a hub that then links to 3 pc's and 2 printers all via ethernet. Connection to the outside world is fine.
A few weeks ago the IT geek decided to switch the modem from DHCP to PPPoA and put each pc & printer on fixed IPs. The Vigor is also on a static IP.
This therefore cut off our link to the Linksys WRTG54 we have in a different room serving as a wireless router.
The Linksys is/was connected via ethernet to port 1, port 2 direct to laptop. Wireless worked fine until they changed to static IP etc on the Vigor, now we only have ethernet to the laptop and no Wireless.
What do we need to do at the Linksys end to get wireless working again?
I bought "Belkin N150 Wireless Modem Router" and while installing noticed that the ADSL slot is too short that does not fit the LAN chord, instead fits the telephone chord. How do I fit the LAN chord fit in the ADSL slot? Any alternatives? My ISP comes with a LAN chord and is connected directly to my PC.
View 3 Replies View RelatedI own a Broadcom BCM5354-based wireless router (Tomato 1.27 flashed) and an Aztech DSL605E modem. When both are powered up, the wireless router sometimes doesn't get internet access because the modem automatically logs itself in. I have to plug the modem cable to my laptop, manually disconnect the modem, and plug the modem cable back to the router to fix it.
View 2 Replies View RelatedI want to configure my router to use 2 ADSL lines each with a dialer and a modem in RFC2684 mode. I have a 2821 (IOS 12.4) with an HWIC-4ESW.
My network topology is like this :
ADSL Modem 1 (RFC2684) --
(Fa0/0/0)
Router -- (Gi0/1) MyLAN
(Fa0/0/1)
ADSL Modem 2 (RFC2684) --/
1. I configure my DSL Modem in RFC 2684. The first use 172.16.0.2/29 and the second 172.16.0.3/29. I connect this devices to Fa0/0/0 and Fa0/0/1.
2. I configure Vlan1 to use the network configured on my modem :
interface Vlan1
ip address 172.16.0.1 255.255.255.248
3. I try to ping my devices :
#ping 172.16.0.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.0.3, timeout is 2 seconds:
!!!!!
[code]....
how do you set up an ethernet port for DHCP with a Belkin ADSl modem with wireless G router, model number F5D7632-4?
View 1 Replies View Relatedi have a adsl modem tp link td 8840, and i had this up and running well for about 3 days. then we decided to get a router cause my little sis got a ipad2.the router is dlink dir 61.so basically i followed all the instructions and the internet was working fine.then for some reason ign site stopped working, i thought that it was down for some reason and didn't think much of it and today when i tryed to go into hotmail or facebook it doesn't work either. so i can get into the log in pages of both, but when i put in the id and password, the screen goes blank and just says waiting for .... on the bottom (using google chrome).and it never loads.i tryed with other internet browsers and it din't work so i took out the router and re wired the adsl modem only and voila. all the sites started working again.i want to use my router but i don't know why i can't acess some sites when i have it connected.
View 1 Replies View RelatedRegion : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version :
ISP : Streamyx
In the process of Lan setting my new wireless adsl modem router TD-W8968, an error message shown when I press save. Error Code: 1, Internal error.
At home I have a D Link DSL-2640R wireless adsl router/modem in my downstairs office.I would like to use the cable which goes to upstairs of the house to link to some sort of extra router or switch in order to provide more network ports upstairs.
View 1 Replies View RelatedRegion : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version :
ISP :
My Toshiba laptop can't get connected to the wireless ADSL modem router TD-W8960N. I have 4 different laptops and one desktop, all connected to the router very well, only the Toshiba cannot get on Internet. I can connect to the wireless network on the laptop, but it shows limited access.
Lately I encountered random Internet connection issues?My router is a Netgear Wireless ADSL Firewall Modem Router DG834 (Firmware V1.05.0) and my ISP, isn't the most reliable regarding bandwidth... All clients (max 3 at the same time) connect wireless.The problem is that the last few weeks my connections is very unstable, all clients lose the internet connection until you restart the router manually.I can't even connect to the webinterface (192.168.0.1), during the downtimes.
View 4 Replies View RelatedI have Desktop and Laptop connected to a Huawei-make,Model No Smart AX 882, ,via ethernet & USB port. Is it possible to convert the same ADSL wired modem into a wireless modem for my Laptop. the type of hardware to be used (e.g., wireless access point or a wireless router) through my USB port in the wired modem? what is the configuration change I have do in my wired broad band modem?
View 1 Replies View RelatedTwo days ago we received our new phone land line from Mediacom. We already had internet service from them so we decided to get a phone line. When they came over two days ago, we received a new modem, RCA DHG535-2. The issue we are experiencing is that the modem is not connecting to our rt n-16 ASUS wireless router. The modem works fine without the router but we need it for school work. The troubleshooter says "DNS is not available".A few things i tried was to unplug everything and reconnect them back from the modem to the computer.It usually works when i had trouble in the past but it seems nothing is working.
View 4 Replies View RelatedI am new using cisco router 2600, i want to use dmz like adsl modem to direct ip public to ip lan like 180.15.22.x.x to ip lan 192.168.1.2 ( lrouter mikrotik ) outside to inside so when i call ip public then forrward to mikrotik
View 2 Replies View Related
