At home I have a D Link DSL-2640R wireless adsl router/modem in my downstairs office.I would like to use the cable which goes to upstairs of the house to link to some sort of extra router or switch in order to provide more network ports upstairs.
We have a router operating in front of one computer which is separate from the rest of the network. Most of the time it operates fine but we find sometimes it loses connectivity, both internet connectivity from the machine and access to the machine remotely. This is not acceptable as the machine is operating rather critical processes and ideally it should be available 100% of the time.
I cannot determine if the fault lies with Windows, the router or the network.
ADSL Connection Type PPPoE/PPPoA Firmware v1.06 Port forwarding None DNS Auto Firewall None DMZ 192.168.1.2
i have a adsl modem tp link td 8840, and i had this up and running well for about 3 days. then we decided to get a router cause my little sis got a ipad2.the router is dlink dir 61.so basically i followed all the instructions and the internet was working fine.then for some reason ign site stopped working, i thought that it was down for some reason and didn't think much of it and today when i tryed to go into hotmail or facebook it doesn't work either. so i can get into the log in pages of both, but when i put in the id and password, the screen goes blank and just says waiting for .... on the bottom (using google chrome).and it never loads.i tryed with other internet browsers and it din't work so i took out the router and re wired the adsl modem only and voila. all the sites started working again.i want to use my router but i don't know why i can't acess some sites when i have it connected.
I am connecting to internet via 3g HSDPA modem which is connected to my PC. And i have a i touch 4g and i need to get wireless access to it via HSDPA modem, So is it possible or is there any device and a method where i can create a wireless network via HSDPA modem? Btw my PC has Windows XP.
my dlink dsl-520b dls modem is using 192.168.1.1 and is plugged into the WAN port on my dlink wireless router.the wireless router is 192.168.0.1. (these are both in the main building which is remote from my shop).Then i have a netgear wireless access point This spreads the signal properly, and I can get connectivity on all my computers -although i do have to specify a default route on the computers on my shop side of the access point.I noticed that the internet light on my modem is red which indicates no internet connection. I am still able to access the internet fine, but i would like to be able to log into the modem from my network. I was able to do this before by setting a computer with a netmask of 255.255.0.0.
I need to create multiple ip-sec vpn tunnels on A Cisco 837 ADSL Router. I am able to create one tunnel but the second connection is asking for the outside interface which is atm and already taken by the first tunnel. How can i create more tunnels?
Secondly, after creating the first tunnel i am able to access the remote lan network but when i tried tracert "remote lan ip of a pc" from my pc i got "request timed out" after passing my 837 but succeeded to reach the target. Does tracert needs something to be opened in the router?
We are using a Westell 7500 wireless modem/router from Frontier without any problemsI have two d-link wireless n300 routers that I want to add to network so I can add them to our DirecTV DVR's. I have tried using the D-link CD and instructions without any success. Everytime it prompts me for my 1st router's (the Westell's) login/password, it says it's invalid. If I then click to continue w/o the logon and password, it then gives me an error when it is trying to add the d-link. I have tried everything. My Westell IP is 192.168.1.1. How can I access and add the d-link routers? Is there an easier way?
My internet is running through a D-Link DIR-655 router at home it's giving me some problems at the moment.Me and my roomie both play World of Warcraft and we both have to have the ports open for updates, and it won't let me.It will only let me open the ports for 1 IP, if i try to open it for more it 'conflicts', it's only passing through the port in the router, it's not dedicated to one IP.
I've a Shiro DSL805E Modem and to connect to multiple computers, I connected an Encore 5 Port Switch. Now I got laptop and thought of getting a wireless network, so I bought TP-Link TL-MR3420 Wireless Router and connected it to the one of the wires from the Encore Switch. But I'm unable to access the internet through TP-Link Router but the internet works fine for the computers which are directly connected to switch. how to do ip settings for TP-Link Router. But when I connect router directly to modem by bypassing switch, it works fine but not via switch. I have some restrictions due to which I have to strictly following this sort of connection: Modem -Switch - Router
We have a Vigor ADSL modem linked to a hub that then links to 3 pc's and 2 printers all via ethernet. Connection to the outside world is fine.
A few weeks ago the IT geek decided to switch the modem from DHCP to PPPoA and put each pc & printer on fixed IPs. The Vigor is also on a static IP.
This therefore cut off our link to the Linksys WRTG54 we have in a different room serving as a wireless router.
The Linksys is/was connected via ethernet to port 1, port 2 direct to laptop. Wireless worked fine until they changed to static IP etc on the Vigor, now we only have ethernet to the laptop and no Wireless.
What do we need to do at the Linksys end to get wireless working again?
I bought "Belkin N150 Wireless Modem Router" and while installing noticed that the ADSL slot is too short that does not fit the LAN chord, instead fits the telephone chord. How do I fit the LAN chord fit in the ADSL slot? Any alternatives? My ISP comes with a LAN chord and is connected directly to my PC.
I own a Broadcom BCM5354-based wireless router (Tomato 1.27 flashed) and an Aztech DSL605E modem. When both are powered up, the wireless router sometimes doesn't get internet access because the modem automatically logs itself in. I have to plug the modem cable to my laptop, manually disconnect the modem, and plug the modem cable back to the router to fix it.
how to connect a adsl modem to a computer network using a switch with a server.I have a network with a server and about ten clients computers all connected through a switch, the server has an IP 192.168.1.1 as its gateway. I want to connect adsl modem to the switch so that all the computers can have access to the net, but the adsl too has 192.168.1.1 as its IP.
I have 2 laptops up stairs with a Wireless router and i have a PC down stairs and might be adding a second one PC too. Is there a way i can run my wireless router upstairs and run another router down stairs too.i would like to use my NIC cards downstairs connect to my network. i dont really want to buy a wireless adapter for the PC's down stairs.Could i even run a cat5 from the wireless router down to a wired router down stairs? Looking for the best/easiest/cost effective solution.
My uncle has just received broadband. We have a router which is connected to his phone line, but the computer is upstairs. We have measured it and it needs 20 metres of broadband and ethernet cabling to fit. Once we get these cables, can it just be connected as the cable is going to go up the stairs and is hazardous
Region : UnitedStates Model : TD-W8960N Hardware Version : V3 Firmware Version : ISP :
My Toshiba laptop can't get connected to the wireless ADSL modem router TD-W8960N. I have 4 different laptops and one desktop, all connected to the router very well, only the Toshiba cannot get on Internet. I can connect to the wireless network on the laptop, but it shows limited access.
Have one switch and network.PC number one have win98 and network adapter and connected to the switch.PC number two have winXP and network adapter and connected to the switch same as win98.Network works on win98 and winxp they see each other.internet working on winxp but dont work on win98
I have Desktop and Laptop connected to a Huawei-make,Model No Smart AX 882, ,via ethernet & USB port. Is it possible to convert the same ADSL wired modem into a wireless modem for my Laptop. the type of hardware to be used (e.g., wireless access point or a wireless router) through my USB port in the wired modem? what is the configuration change I have do in my wired broad band modem?
Lately I encountered random Internet connection issues?My router is a Netgear Wireless ADSL Firewall Modem Router DG834 (Firmware V1.05.0) and my ISP, isn't the most reliable regarding bandwidth... All clients (max 3 at the same time) connect wireless.The problem is that the last few weeks my connections is very unstable, all clients lose the internet connection until you restart the router manually.I can't even connect to the webinterface (192.168.0.1), during the downtimes.
We setup a home network in our new house but we have a problem with limited connectivity in specific configuration.
There is few situations to describe the problem :
1. If I connect my computer directly to the modem I can access to the internet. (modem --> computer = internet OK)
2. If i connect the ethernet cable (in the wall) between my modem and RJ45 jack in the living room and connect my computer directly to the RJ45 I can access to the internet. (modem --> cat6 cable in the wall --> computer = internet ok)
3. If I connect my router directly (without the cat6 cable in the wall) to the modem and my computer to the the router I can access to the internet. (modem --> router --> computer = internet ok)
4. If i connect the ethernet cable (in the wall) between my modem and RJ45 jack in the living room and connect to router to the RJ45 and my computer to the router I CANNOT access to the internet. (modem --> cat6 cable in the wall --> router --> computer = internet access problem)
5. If i connect the ethernet cable (in the wall) between my modem and RJ45 jack in the living room and connect to a swith to the RJ45 and my computer to the switch I can access to the internet. (modem --> cat6 cable in the wall --> switch --> computer = internet OK)
With those tests I am not able to figured out what is the problem... router is working in situation #3. cable in the wall is ok in situations #2 and 5. How to make my router working when connected to the RJ45 jack in the living room.
There is my component : Router --> D-Link WBR-2310 Switch --> Trendnet TE100-S5 Modem --> Thomson DCM475 Cable in the wall --> Homemade with 568A standard in both end.
I want to transfer files between two computers.i have a Router+Adsl modem i want to network two pc one is running windows xp and other is running windows 7.i plug both pc's cable in Router and LAN card...after that my network places shows below picture i didn't configure anything. url...when i click other network pc it ask me user name and password. url...I never did networking. how can i transfer files between two pc's while internet don't stop.
we were happily getting along with our RCN cable Motorola modem and DLink wireless 655 until the last couple of weeks. The internet would intermittently not be available, without warning. First couple of times we power cycled the modem and router, and it worked, but then stopped being available altogether. I got some support from RCN, the cable provider (they own the modem and it's old, so naturally that was my first thought). I now have a new modem and the situation is exactly the same. The error message that I get is that the IP address for the network cannot be found.
I got internet access by bypassing the router, connecting the modem directly to my (Windows XP) PC, releasing and renewing the IP address, and power cycling the modem. However, the internet still intermittently shuts down, and of course turning off the computer necessitates the whole procedure again. And now we have no wireless. Should we assume it's the router, and a new one would solve our problem? Of do we just need to reset the IP address of the router?
have wireless d-link adsl modem router which usually use for adsl connection sharing, but i have a cable internet connection, so my question is can i share my cable internet connection with this router?
I've had a D-link N750 DB running smoothly for about a year now. Suddenly the other day, for no apparent reason, it dropped its connection to the modem and refuses to acknowledge it anymore. The router still broadcasts the network ESSID and accepts external connections.
First, the cable modem appears to work just fine, as I'm able to hard wire with a laptop and get consistent internet service. Second, when in the router settings, the ethernet connection status reads not detected, so it seems to me that the router hardware has no idea its got anything plugged into it.
I've tried the standard power cycling methods in various orders about a dozen times. I've replaced cables and done a hard reset of router settings. No dice.
I am looking to purchase an ADSL wireless modem router combo which will be mainly used for net browsing, online gaming (ps3) and skype.It has been suggested by the IT tech we use that I a get dual band n wireless gigabit modem/router but my limited knowledge and the confusion created by reading multiple contracting reviews of products is sending me a bit loopy.
I have a problem connecting wifi router(airlive wt-2000r) to my ADSL modem(webstar epc2203ed2.0) using utp patch cable. When my PC is connected straight to the ADSL modem everything works like charm. But when I connect modem with wan port on the router and router with my PC I get no internet access. The network shows as unidentified network and win7 troubleshooter says: Default gateway not available. Connecting them two devices seems pretty simple and I dont think I am doing anything wrong so what could be the problem?
configuring my new Cisco 881 Router with my existing ADSL modem.At the moment, i am connecting to the internet using tp-link modem router, all PPPoE/DHCP/Wireless is set up there...and that connect to the switch where all my computer connected to.
Now i want to connect this new Cisco Router to it to basically do the firewall/filtering/dhcp...leave the authentication thing on my Modem.Can i get a head start what to configure here on the cisco? since it does not work as easily as other Router where I can just plug a cable from modem LAN to Router LAN.