have wireless d-link adsl modem router which usually use for adsl connection sharing, but i have a cable internet connection, so my question is can i share my cable internet connection with this router?
View 1 Replieswe were happily getting along with our RCN cable Motorola modem and DLink wireless 655 until the last couple of weeks. The internet would intermittently not be available, without warning. First couple of times we power cycled the modem and router, and it worked, but then stopped being available altogether. I got some support from RCN, the cable provider (they own the modem and it's old, so naturally that was my first thought). I now have a new modem and the situation is exactly the same. The error message that I get is that the IP address for the network cannot be found.
I got internet access by bypassing the router, connecting the modem directly to my (Windows XP) PC, releasing and renewing the IP address, and power cycling the modem. However, the internet still intermittently shuts down, and of course turning off the computer necessitates the whole procedure again. And now we have no wireless. Should we assume it's the router, and a new one would solve our problem? Of do we just need to reset the IP address of the router?
I'm trying to learn Cisco ASA IOS commands, I have bought myself a 5505 ASA for my home network and plan to implement it. How best to configure it.
I have attached a diagram of how I want my network to look. The internet connection is via the Virgin Media cable modem.
I just ordered the Linksys WAG120N modem/ router and need configuring the same on the BSNL network. Any Document or link about his Installation and configuration.
View 3 Replies View RelatedI have 2 mbps line with D-link modem shared by 2 persons through wire. Sometime I feel that my client is using more band width than me so I want to know is there is any way I can control the speed of my client.
View 1 Replies View RelatedI have WAG120N and is working fine, but has very poor wifi range. I recently purchased EA 6500. how to setup my WAG120N as a modem only and shift all routing to the EA6500
View 2 Replies View RelatedI have a Pix 501 running 6.3 code sitting behind a cable modem. I use ip address outside dhcp setroute because I don't have a dedicated IP from my cable provider.
How do I configure the Pix to host VPN connections from my iPad when offsite? Since the outside interface is going to change, I can't configure a static IP.
I have cable internet can I use 2wire DSL router/modem with cable internet? I need to do wireless in my house?
View 1 Replies View RelatedI updrade my wireless router from 54 mpb to 150. Now my pc/router isn't connecting to the modem. How do I correct
View 1 Replies View RelatedMy Comcast cable modem does not have a 2nd port needed to connect my Belkin AC1200 wireless router. Is there another way to configure this or are my options to either buy a new cable modem or try to upgrade it through Comcast?
View 1 Replies View RelatedI am attempting to install the router but cannot connect to SKY ISP. I can connect my laptop to the router both wirelessly and by cable.
View 5 Replies View RelatedI have an ADSL connection using a wireless DLink modem 2730U I want to share my internet with my neighbour as limited speed and limited traffic.How can I do this? Is it possible as wireless?
View 4 Replies View Relatedhow i can configure dlink dl624
View 1 Replies View RelatedThe detected problem is the connection between my access point, router, or cable modem and the Internet is broken.The network gateway is accessible, but Windows couldn't receive network traffic from the Internet.All other devices (iPad, Xbox, android phone) have no problem connecting to the Internet.Desktop is the only one experiencing the connection issue.
View 1 Replies View RelatedMy laptop died last week and have been using my husbands, which I hate! We had some issues with computer freezing on some webpages or after being on webpages for awhile (like facebook). Yesterday it froze and I could not get it back on. When he got home he did scan disk (which I also did) and got it working after going into safe mode and doing system restore. He said an update had gotten through and messed things up. Anyhow, after he was on it a few hours last night, we lost connection. I figured the crazy weather was the culprit but it has been off all day. Our router is working and connecting but the adapter is not. Also our home phone says there is no line. We have unplugged everything several times, checked to make sure everything is in the right spots, I have even reset the router and rebooted the adapter. I uninstalled and restalled the adapter also. It is now telling me that "the connection between your access point, router, or cable modem and the Internet is broken". The only lights I have on the adapter are power, battery, DS and now the US light is blinking. The online and link lights are not on.
View 3 Replies View RelatedConfigure dlink router remote desktop?
View 1 Replies View RelatedI'm on a Virgin media 50 Meg connection currently connected via cable using the modem provided.I'm hoping to connect my PS3 to the internet using the router provided (dlink DIR-615) and I'm wondering if I'll still get the same speeds if I connect the cable through the router. I hear that the wireless data transfer won't be able to handle 50 Meg but if I attach a cable from the router to my PC will I still get the full 50?
View 1 Replies View RelatedI am with Virgin media and have a home lab (2611 routers, 3550 switches, 2950s etc) which i usually just use for testing things on and practicing.
Now I tried to connect it to the internet and got some weird things happening.
I got NAT and DHCP client all setup correctly on the router (or so I think!) along with DNS settings but I still can't get Internet access.
My network is all setup right so that through using OSPF the router is the gateway (0.0.0.0 route) for all devices. Doing a traceroute confirms this.
Yet I never get any further than the router? I see IP nat translations ticking up as I send more requests but never get a webpage or a reply from any of the machines in my network.
HOWEVER... The router itself does get some replies from Google.co.uk and bbc.co.uk but doesn't seem to want to give anything else on the "inside" a response?
Here is a dump of config:
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[Code].....
I am having an issue with my network that has me perplexed. I have a DPC3010 cable modem (Charter internet). I previously had it connected to a Linksys WRT54GL with DD-WRT installed and that was working OK except that I had to reboot it 2-3 times per week. I replaced it with a Cisco 861 (non-wireless) router and it worked OK for a few hours then it started dropping the internet connection (it goes up and down constantly). If I switch back to the Linksys everything works fine again. I am using the same cables in either case so I know it's not a cabling issue. I upgraded the firmware to c860-universalk9-mz.151-4.M3.bin, but it made no difference. I was starting to suspect a problem with the physical ports on the router, but I decided to try connecting the 861 behind the Linksys and turns out it works fine in that setup.
So to recap...
If I connect the 861 directly to the modem my internet connection bounces up and down
If I connect the Linksys directly to the modem my internet connection is fine
If I connect the Linksys directly to the modem and the 861 to the Linksys everything works fine (my PC is connected to the fe0 port of the 861)
Are the 861 and the modem simply incompatible or is it a configuration issue? I have attached my 861 config to this thread.
We setup a home network in our new house but we have a problem with limited connectivity in specific configuration.
There is few situations to describe the problem :
1. If I connect my computer directly to the modem I can access to the internet. (modem --> computer = internet OK)
2. If i connect the ethernet cable (in the wall) between my modem and RJ45 jack in the living room and connect my computer directly to the RJ45 I can access to the internet. (modem --> cat6 cable in the wall --> computer = internet ok)
3. If I connect my router directly (without the cat6 cable in the wall) to the modem and my computer to the the router I can access to the internet. (modem --> router --> computer = internet ok)
4. If i connect the ethernet cable (in the wall) between my modem and RJ45 jack in the living room and connect to router to the RJ45 and my computer to the router I CANNOT access to the internet. (modem --> cat6 cable in the wall --> router --> computer = internet access problem)
5. If i connect the ethernet cable (in the wall) between my modem and RJ45 jack in the living room and connect to a swith to the RJ45 and my computer to the switch I can access to the internet. (modem --> cat6 cable in the wall --> switch --> computer = internet OK)
With those tests I am not able to figured out what is the problem... router is working in situation #3. cable in the wall is ok in situations #2 and 5. How to make my router working when connected to the RJ45 jack in the living room.
There is my component :
Router --> D-Link WBR-2310
Switch --> Trendnet TE100-S5
Modem --> Thomson DCM475
Cable in the wall --> Homemade with 568A standard in both end.
I changed the router ip to 192.168.0.2 from 192.168.0.1. I don't know what type of connection, i have to use. It have the following options: Static IP, DHCP etc. The internet connectivity status shows 'disconnected'.I'm currently using the lan to connect to net. ISP gave me a username and password to Login with a browser to start browsing. Since multiple devices are use in same connection, they provided 2 IP.
View 1 Replies View Relatedmy dlink dsl-520b dls modem is using 192.168.1.1 and is plugged into the WAN port on my dlink wireless router.the wireless router is 192.168.0.1. (these are both in the main building which is remote from my shop).Then i have a netgear wireless access point This spreads the signal properly, and I can get connectivity on all my computers -although i do have to specify a default route on the computers on my shop side of the access point.I noticed that the internet light on my modem is red which indicates no internet connection. I am still able to access the internet fine, but i would like to be able to log into the modem from my network. I was able to do this before by setting a computer with a netmask of 255.255.0.0.
View 6 Replies View Relatedhow can i connect a Net gear DGN2200 wireless modem router to a D link DGL4500 wireless router ??
View 1 Replies View RelatedI've had a D-link N750 DB running smoothly for about a year now. Suddenly the other day, for no apparent reason, it dropped its connection to the modem and refuses to acknowledge it anymore. The router still broadcasts the network ESSID and accepts external connections.
First, the cable modem appears to work just fine, as I'm able to hard wire with a laptop and get consistent internet service. Second, when in the router settings, the ethernet connection status reads not detected, so it seems to me that the router hardware has no idea its got anything plugged into it.
I've tried the standard power cycling methods in various orders about a dozen times. I've replaced cables and done a hard reset of router settings. No dice.
Region : Malaysia
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.12.8 Build 110418 Rel.43954n
ISP : Celcom
my tl-mr3220 not detect my 3g usb modem dlink dwm-156.
We are using a Westell 7500 wireless modem/router from Frontier without any problemsI have two d-link wireless n300 routers that I want to add to network so I can add them to our DirecTV DVR's. I have tried using the D-link CD and instructions without any success. Everytime it prompts me for my 1st router's (the Westell's) login/password, it says it's invalid. If I then click to continue w/o the logon and password, it then gives me an error when it is trying to add the d-link. I have tried everything. My Westell IP is 192.168.1.1. How can I access and add the d-link routers? Is there an easier way?
View 16 Replies View Relatedi have a adsl modem tp link td 8840, and i had this up and running well for about 3 days. then we decided to get a router cause my little sis got a ipad2.the router is dlink dir 61.so basically i followed all the instructions and the internet was working fine.then for some reason ign site stopped working, i thought that it was down for some reason and didn't think much of it and today when i tryed to go into hotmail or facebook it doesn't work either. so i can get into the log in pages of both, but when i put in the id and password, the screen goes blank and just says waiting for .... on the bottom (using google chrome).and it never loads.i tryed with other internet browsers and it din't work so i took out the router and re wired the adsl modem only and voila. all the sites started working again.i want to use my router but i don't know why i can't acess some sites when i have it connected.
View 1 Replies View RelatedI can't get a new IP from my ISP when my Cable modem router(EPC3925) is set to router mode, i have tried factory restore, unplugged etc..but still no luck. It changes each time i reset it when i set it to bridged only mode but then i won't be able to connect other devices to it since it doesn't uses DHCP in bridged only mode. It changes back to the IP i had when i set it to router mode. I don't want to change my router settings to bridged only because it would disconnect the other devices in my house. Why my ISP assigns the same IP address when it's set to router mode but assigns different IPs when it's set to bridged only, how is this possible ?
View 1 Replies View RelatedI have a cable modem installed to my property but want to use my modem/router to go wireless. The proble is my cable modem output is a RJ45 and the router input is RJ11.
View 10 Replies View RelatedAt home I have a D Link DSL-2640R wireless adsl router/modem in my downstairs office.I would like to use the cable which goes to upstairs of the house to link to some sort of extra router or switch in order to provide more network ports upstairs.
View 1 Replies View RelatedI'm switching to cable internet service instead of DSL. My Netgear router will not work with my cable modem; but it works like a charm with my DSL modem. Is it a problem with the router setup? Good thing I still have the DSL service.
View 3 Replies View RelatedI have DSL setup in my house and I want to know if using a cable modem will work and increase my speed. And will it work with a linksys router
View 1 Replies View RelatedMy mother has an older Compaq laptop running XP home edition. She hasn't used this laptop for a while and it won't connect to the internet through her cable modem.I know it isn't a modem or ISP problem since my laptop will connect just fine. By the way, we are connecting to the cable modem with a cat 5.
View 5 Replies View Related