DLink WBR-2310 Router Don't See Modem But Switch Does
May 24, 2012
We setup a home network in our new house but we have a problem with limited connectivity in specific configuration.
There is few situations to describe the problem :
1. If I connect my computer directly to the modem I can access to the internet. (modem --> computer = internet OK)
2. If i connect the ethernet cable (in the wall) between my modem and RJ45 jack in the living room and connect my computer directly to the RJ45 I can access to the internet. (modem --> cat6 cable in the wall --> computer = internet ok)
3. If I connect my router directly (without the cat6 cable in the wall) to the modem and my computer to the the router I can access to the internet. (modem --> router --> computer = internet ok)
4. If i connect the ethernet cable (in the wall) between my modem and RJ45 jack in the living room and connect to router to the RJ45 and my computer to the router I CANNOT access to the internet. (modem --> cat6 cable in the wall --> router --> computer = internet access problem)
5. If i connect the ethernet cable (in the wall) between my modem and RJ45 jack in the living room and connect to a swith to the RJ45 and my computer to the switch I can access to the internet. (modem --> cat6 cable in the wall --> switch --> computer = internet OK)
With those tests I am not able to figured out what is the problem... router is working in situation #3. cable in the wall is ok in situations #2 and 5. How to make my router working when connected to the RJ45 jack in the living room.
There is my component :
Router --> D-Link WBR-2310
Switch --> Trendnet TE100-S5
Modem --> Thomson DCM475
Cable in the wall --> Homemade with 568A standard in both end.
View 5 Replies
ADVERTISEMENT
Feb 4, 2011
I want to use a D-link WB-2310 wireless router to receive a wireless signal. Downstairs, connected to a cable modem (11MBPS), is an intel iMac running 10.4 that can send out its own wifi signal (internet sharing). Upstairs will be a PowerPC G5 Mac running 10.5 that has no wireless card...I was hoping I could use the router in place of a wireless adapter.
View 3 Replies
View Related
Nov 23, 2011
I have a dlink wbr 2310 router and i keep on getting hit offline on my xbox 360 because my parents set my router on open connection so anyone close enough to pick it up can use it and I'm trying to close the connection so they would have to know my password to use it?
View 1 Replies
View Related
Aug 30, 2012
I was assisting a friend by trying to set up a wireless password on their network, I have no clue why they didn't have one, and when it did the normal resetting machine protocol after the password setup we lost all internet, we can connect to the wireless network fine but it has no internet. The modem has internet connection as when I link via ethernet I can connect to the internet. DHCP is not enabled on the router, I'm not sure if I have to set that setting on the modem? or frankly how to do that either.
View 7 Replies
View Related
May 2, 2011
we were happily getting along with our RCN cable Motorola modem and DLink wireless 655 until the last couple of weeks. The internet would intermittently not be available, without warning. First couple of times we power cycled the modem and router, and it worked, but then stopped being available altogether. I got some support from RCN, the cable provider (they own the modem and it's old, so naturally that was my first thought). I now have a new modem and the situation is exactly the same. The error message that I get is that the IP address for the network cannot be found.
I got internet access by bypassing the router, connecting the modem directly to my (Windows XP) PC, releasing and renewing the IP address, and power cycling the modem. However, the internet still intermittently shuts down, and of course turning off the computer necessitates the whole procedure again. And now we have no wireless. Should we assume it's the router, and a new one would solve our problem? Of do we just need to reset the IP address of the router?
View 1 Replies
View Related
Jun 30, 2011
have wireless d-link adsl modem router which usually use for adsl connection sharing, but i have a cable internet connection, so my question is can i share my cable internet connection with this router?
View 1 Replies
View Related
May 12, 2012
my dlink dsl-520b dls modem is using 192.168.1.1 and is plugged into the WAN port on my dlink wireless router.the wireless router is 192.168.0.1. (these are both in the main building which is remote from my shop).Then i have a netgear wireless access point This spreads the signal properly, and I can get connectivity on all my computers -although i do have to specify a default route on the computers on my shop side of the access point.I noticed that the internet light on my modem is red which indicates no internet connection. I am still able to access the internet fine, but i would like to be able to log into the modem from my network. I was able to do this before by setting a computer with a netmask of 255.255.0.0.
View 6 Replies
View Related
Dec 24, 2011
how can i connect a Net gear DGN2200 wireless modem router to a D link DGL4500 wireless router ??
View 1 Replies
View Related
Feb 13, 2013
I've had a D-link N750 DB running smoothly for about a year now. Suddenly the other day, for no apparent reason, it dropped its connection to the modem and refuses to acknowledge it anymore. The router still broadcasts the network ESSID and accepts external connections.
First, the cable modem appears to work just fine, as I'm able to hard wire with a laptop and get consistent internet service. Second, when in the router settings, the ethernet connection status reads not detected, so it seems to me that the router hardware has no idea its got anything plugged into it.
I've tried the standard power cycling methods in various orders about a dozen times. I've replaced cables and done a hard reset of router settings. No dice.
View 8 Replies
View Related
Nov 22, 2012
Region : Malaysia
Model : TL-MR3220
Hardware Version : V1
Firmware Version : 3.12.8 Build 110418 Rel.43954n
ISP : Celcom
my tl-mr3220 not detect my 3g usb modem dlink dwm-156.
View 1 Replies
View Related
Jun 1, 2011
can i use dlink switch as a router to set up LAN
View 1 Replies
View Related
Jun 18, 2011
We are using a Westell 7500 wireless modem/router from Frontier without any problemsI have two d-link wireless n300 routers that I want to add to network so I can add them to our DirecTV DVR's. I have tried using the D-link CD and instructions without any success. Everytime it prompts me for my 1st router's (the Westell's) login/password, it says it's invalid. If I then click to continue w/o the logon and password, it then gives me an error when it is trying to add the d-link. I have tried everything. My Westell IP is 192.168.1.1. How can I access and add the d-link routers? Is there an easier way?
View 16 Replies
View Related
Apr 30, 2011
i have a adsl modem tp link td 8840, and i had this up and running well for about 3 days. then we decided to get a router cause my little sis got a ipad2.the router is dlink dir 61.so basically i followed all the instructions and the internet was working fine.then for some reason ign site stopped working, i thought that it was down for some reason and didn't think much of it and today when i tryed to go into hotmail or facebook it doesn't work either. so i can get into the log in pages of both, but when i put in the id and password, the screen goes blank and just says waiting for .... on the bottom (using google chrome).and it never loads.i tryed with other internet browsers and it din't work so i took out the router and re wired the adsl modem only and voila. all the sites started working again.i want to use my router but i don't know why i can't acess some sites when i have it connected.
View 1 Replies
View Related
Jan 22, 2013
At home I have a D Link DSL-2640R wireless adsl router/modem in my downstairs office.I would like to use the cable which goes to upstairs of the house to link to some sort of extra router or switch in order to provide more network ports upstairs.
View 1 Replies
View Related
Sep 22, 2012
I've had my network up and running for several years with no issues. Last week I upgraded my router to a Dlink 826L and now anything connected to my downstream Dlink DSS16+ can't be accessed.
View 3 Replies
View Related
Aug 2, 2012
I have a Free Community WiFi that I can access from the edges of my house, but not from anywhere inside the house. My personal Internet connection is out due to the fact our bill trippled for some reason we can't figure out 2 months ago without telling us. We've had an auto payment sent every month for just over what it should be. So until I get this sorted out with the ISP I have to use the community WiFi. I would like to be able to use the internet from somewhere other than the wall in my kitchen.
So, I have a number of Routers, 2 Actiontec Q1000s, but only 1 power suply, a D-Link WBR-2310, D-Link DIR-601 & a few other ods & Ends including a 12DB Amped Wireless & An 8DB Hawking Tech antennas.What I want to do is to use 1 router to connect to the CommunityShared Network, A wired connection to another router (Preferably the Q1000 as it's already setup for my Home Network) & that router to serve my Home Network, preferably over the WAN port if possible, but I can run VPNs on each device for a week if I have to.
Right now I have one computer setup in the kitchen with a High Gain Antenna conected to a Atheros SUB-362 EXT USB WiFi card, (This computer gets 7Mbps Down & 9Mbps Up) then the built-in WiFi card connected to my Home network with a Static IP, The Q1000 set to use that IP as the Gateway. I can get about 200Kbps max on devices connected to the Home Network. But the biggest problem is that my old Atheros card disconnects randomly when accessed from one of the devices on the home network. I'm fine with a ThirdParty Firmware Update on the D-Links if necessary.When I look online I only find posts about how to extend a network using a second router or how to use a specific router to repeat or bridge.
View 1 Replies
View Related
Sep 7, 2012
My new housemate from France has arrived and was going to connect wirelessly to my network. But when he clicks to join the network we are waiting for like 30 mins for the computer to connect. Then when we change the settings for WPA, it doesn't accept the WPA key. We've tried everything and dont know what we might be doing wrong or what settings. He has a Toshiba Satellite and Windows XP.
View 3 Replies
View Related
Feb 12, 2012
I have a Westell 7500 wireless modem that I would like to bridge to my Dlink DIR-628.
View 1 Replies
View Related
Jan 2, 2013
I need to reset my DLink wireless modem all over again, can't get it to recognise the router, so thought that it would need to reset to factory defaut, how can I do this. Tried just hitting reset on the router,but nothing is happening.
View 4 Replies
View Related
Apr 2, 2011
I have a D Link WL-2100 AP, I connected my PC to AP with ethernet cable, then I tried to connect the AP to my wireless modem but I couldn't do.How can I make the AP recognize wireless modem?
View 2 Replies
View Related
Feb 23, 2013
I have 2 mbps line with D-link modem shared by 2 persons through wire. Sometime I feel that my client is using more band width than me so I want to know is there is any way I can control the speed of my client.
View 1 Replies
View Related
Jun 22, 2012
change the password on a d-link wireless modem dwl2100ap
View 1 Replies
View Related
Apr 12, 2012
I have a DLink D604T wireless modem. It has been working fine for the past 5 years but today the connection to my netbook computer kept dropping out.I can fix it temporarily by going into Network Connections, right clicking the modem, selecting wireless networks, clicking the modem, going to properties and retyping the network password. I then have to set the firewal to advanced connection settings and typing in my family network password, and changing the Windows firewall settings from On to Off.However, the connection drops out again after just a few minutes. If I then turn the firewall back on, it comes back on again for 5 minutes, but then drops out again. Then I have to repeat the whole process.
View 1 Replies
View Related
Jan 23, 2012
I have an old Dlink DI-604 that I'd like to configure to work as a switch. I think this is possible but not sure how to do it. Switches are cheap but if I could save a few bucks with some tweaking I'd prefer that. Plus I figure I'd learn a bit about networking.Dlinks site on the DI[URL]Uverse and I'm out of wired ports on the Residential Gateway. I would like 2 more ports to network my PC and NAS, so my laptop and Xbox can access their files.
View 4 Replies
View Related
Aug 2, 2012
I have a network which was recently switched from dsl to comcast. The default network is 10.1.10.1. The dhcp is working with the 5 or 6 installed pc's. All pc's are running xp professional.I inserted the dlink 4 port switch to add a new port by inserting it between the router and a pc.
View 4 Replies
View Related
Apr 3, 2011
Can I replace my Replacing D-link 604 w/ D-link ebr-2310 ?
View 4 Replies
View Related
Dec 22, 2011
I have Cyber cafe, And i'm having a problem with My 24 port Dlink "DES 1024d" switch, which has been misbehaving for few months, it looses connectivity to a pcsometimes.....when i reboot the pc, then it works again, But it keep losing connectivity to the other pc's, not at the same time, every time loses connectivity to a different pc.
View 5 Replies
View Related
Feb 6, 2013
My router is a Dlink Model DI-624
My modem is an Arris Model TM502GI don't remember how to set it up. That is what cable goes where & is there anything to do on the PC With WiFi for it to connect with my router?I am 70 years old with a limited knowledge of computer and other electronic gadgets.
View 1 Replies
View Related
Aug 4, 2012
I have an ADSL connection using a wireless DLink modem 2730U I want to share my internet with my neighbour as limited speed and limited traffic.How can I do this? Is it possible as wireless?
View 4 Replies
View Related
Sep 19, 2012
I have a D-Link WBR-2310. It was working just fine until couple days ago. The problem lies with *No Internet Access* that using both wired and wireless. I havereset, shut it down for awhile. Reset the whole device still nothing. I do not have any clue what has happened. I have come up with disabling IPV4 or something? No idea how to do that and if thats right how do I go on to do it.
View 7 Replies
View Related
Jul 8, 2011
I have an Internet Connectivity problem which I believe was caused by resetting our D-Link WBR-2310 router. We have a strange, perhaps illogical network setup in our office. Although it was set up before my time, I have figured it works as follows:
(1) A wired/wireless router (let's call it Router A) is connected directly to the DSL modem.
(2) An Ethernet cord runs from this router to a 5 port switch.
(3) 4 cords run from the switch to individual workstations. These computers obtain their IP addresses automatically.
(4) 1 cord runs from the switch to another wired/wireless router (let's call it Router B).
(5) Two cords run from Router B to individual workstations (let's call them Workstations C). These computers used permanent IP, subnet mask, default gateway, and DNS server addresses. I understand that this was done because they could not obtain their IP addresses automatically.
The problem I've caused seems to stem from me resetting Router B to the factory settings while trying to secure its signal and changing its IP address from 192.168.0.1 to 192.168.1.1 (in order to avoid conflict with the modem which has the same IP address). Once I did that, Workstations C could not access the Internet.
I have tinkered with the TCP/IP settings for Workstations C (e.g. by changing the default gateways to the Router B's new IP address), but it doesn't work. What else should I be doing?
View 2 Replies
View Related
May 3, 2012
I have a question regarding the network setup. I have 3 pieces of network hardware and a fast dsl connection. The hardware is:
- DSL Modem from my provider with static IP connection (CISCO - don't know the symbol)
- DSL Router (edimax ar-7084a)
- Switch (Hewlett-Packard JD871A)
Now the task is to create a LAN network so all my computers can talk together and have a internet connection shared between them.When I connect Modem to Router and then 4 CPUs to router, it is working fine. The problem is that the router has only 4 ports and that it is 100Mbit slow. I would like to use the HP switch for the LAN setup (1Gbit) and then connect the switch to router and router to modem. But it doesn't work I cannot establish internet connection this way. I'm setting all the settings in my router but it doesn't work as it was in simple setup modem->router->cpu. when I add switch to this, the setup is going berserk.Problem is that I would like to create a LAN only between computers using switch. I have other computers that I want to conect to the router directly and don't see the computers using switch.
View 7 Replies
View Related
Sep 6, 2011
I have a network set up currently with a cable modem that goes into a router, the router then goes to a 16 port switch and the switch goes to computers, printers, and my server. I am trying to figure out how to make the modem plug into the switch instead of the router. I'm guessing my problem lies with the default gateway since that is the router. Any suggestions on this? Or how is the best way to set this up? I have 2 NICs on my server and the server has windows 2008 r2.
View 6 Replies
View Related
