I have a 2wire Modem connected to a Cisco Wireless N Router, that is connected to another Cisco Wireless N Router. All was working well. In my absence sbc (AT&T) changed the pass word of the 2wire Modem. The 2wire has stoped communication with the Cisco Wireless N Routers. I connected am Ethernet wire to one of the ports of the 2wire, and connected it to the 2nd Cisco Wireless N Router. The signal gets to the 2nd Cisco Router. However, when I attempt to access the Internet on the CPU connected to the 2 Cisco Router, I get an error Message saying that there is a problem with the Modem and/or Router. On the available Networks selection screen I can see the connections that I want. The selection info shows connected. But when I try to connect, the I can't.
my dlink dsl-520b dls modem is using 192.168.1.1 and is plugged into the WAN port on my dlink wireless router.the wireless router is 192.168.0.1. (these are both in the main building which is remote from my shop).Then i have a netgear wireless access point This spreads the signal properly, and I can get connectivity on all my computers -although i do have to specify a default route on the computers on my shop side of the access point.I noticed that the internet light on my modem is red which indicates no internet connection. I am still able to access the internet fine, but i would like to be able to log into the modem from my network. I was able to do this before by setting a computer with a netmask of 255.255.0.0.
I have a DLink D604T wireless modem. It has been working fine for the past 5 years but today the connection to my netbook computer kept dropping out.I can fix it temporarily by going into Network Connections, right clicking the modem, selecting wireless networks, clicking the modem, going to properties and retyping the network password. I then have to set the firewal to advanced connection settings and typing in my family network password, and changing the Windows firewall settings from On to Off.However, the connection drops out again after just a few minutes. If I then turn the firewall back on, it comes back on again for 5 minutes, but then drops out again. Then I have to repeat the whole process.
We are using a Westell 7500 wireless modem/router from Frontier without any problemsI have two d-link wireless n300 routers that I want to add to network so I can add them to our DirecTV DVR's. I have tried using the D-link CD and instructions without any success. Everytime it prompts me for my 1st router's (the Westell's) login/password, it says it's invalid. If I then click to continue w/o the logon and password, it then gives me an error when it is trying to add the d-link. I have tried everything. My Westell IP is 192.168.1.1. How can I access and add the d-link routers? Is there an easier way?
At home I have a D Link DSL-2640R wireless adsl router/modem in my downstairs office.I would like to use the cable which goes to upstairs of the house to link to some sort of extra router or switch in order to provide more network ports upstairs.
I changed my wireless password by logging in at the netgear site this AM. Haven't been able to get wireless access since. I reset, rebooted (3 computers), tried everything, but nada. I even changed back to the old password. But each time the passphrase was changed, new keys were generated and applies
I am trying to setup ATT DSL modem through D-Link router Dir-615. I was instructed to use PPPoE and setup username and password in router. When I do, the router does not save my network password, but reverts back to some hidden password. I have tried changing it in Tools, but it keeps reverting. I'm sure this is why I cannot access the internet.
I have a d-link router model dir 655.To activate my laptop all that was required was to enter the wps pin.I just purchased an apple ipod touch which is asking for a password.I first tried the wps pin.Then I went to the d-link website and put in my model #.It gave me an ip address which brought up a page where there was a choice admin or user.I picked user.The second choice was to put in a password which I did.The Ipod still says password invalid.I tried numerous times.
I have a d-link DI-524, Im using a modem Xyzel P600 series, my ethernet card is Realtek RTL8101E Family PCI-E.
I already set-up my router and modem. Most of my wireless devices can connect. My problem is it is not secured. When I tried to add WEP or WPA, D-Link restarts but then it cannot connect to my DSL. it says DHCP disconnected and when i try to renew, nothing happened. It just kept on reconnecting. My Desktop has no internet connection.
My d-linl router was not working and I pushed reset button and it went back to factory setting. I don't know what the factory setting is and I want to put my own password but don't know how. I have Window 7?
i have a belkin n300 wireless router and a embarq 660 modem. i wanted to change the password, i don't like the default password. it's too easy to get hacked. anyway, i tried typing the ip address in the address bar of a browser, and it came up a login page, so i created a new login. and then it opens up a page call ZYXEL total internet access solution. it has a lot of setting and button about the network but i couldn't find a button that can change the wireless router's password.