I have a d-link router model dir 655.To activate my laptop all that was required was to enter the wps pin.I just purchased an apple ipod touch which is asking for a password.I first tried the wps pin.Then I went to the d-link website and put in my model #.It gave me an ip address which brought up a page where there was a choice admin or user.I picked user.The second choice was to put in a password which I did.The Ipod still says password invalid.I tried numerous times.
I have WRT54G2 that I've set up my wireless network on. My Kindle, just the basic one, sees and recognizes the network. It has good signal from it. When I attempt to sign in though the Kindle says my password is invalid or it says it just can not connect. I have gone over and checked what I hope are all the settings but to no avail.
Region : Others Model : TL-MR3420 Hardware Version : V2 Firmware Version : 2.1 ISP : PTCL
trying to connect to router configuration (after several factory resets) at 192.168.0.1 but each time screen displays invalid username / password,doesnot even display username / password window,using admin as username and password,just cannot log on to configuration setup
My mother accidentally turned off wireless or changed the password to the 2WIRE778 that we have and I can't get wifi on my iPod. So I have a small motorola router and it's wireless so if I hook it up to the original 2WIRE that has blocked wifi do you think I can get wifi off the second router with no password troubles or would I have to buy a special router that has no password? I don't know a lot about computers. And my Meyer has a password on our computer so I can't log on. so if I just hook up the 2nd router and possibly get WiFi do I need to do anything such as setup on the computer or can I plug it in and just go?
I have a d-link DI-524, Im using a modem Xyzel P600 series, my ethernet card is Realtek RTL8101E Family PCI-E.
I already set-up my router and modem. Most of my wireless devices can connect. My problem is it is not secured. When I tried to add WEP or WPA, D-Link restarts but then it cannot connect to my DSL. it says DHCP disconnected and when i try to renew, nothing happened. It just kept on reconnecting. My Desktop has no internet connection.
My d-linl router was not working and I pushed reset button and it went back to factory setting. I don't know what the factory setting is and I want to put my own password but don't know how. I have Window 7?
I have a dlink wbr 2310 router and i keep on getting hit offline on my xbox 360 because my parents set my router on open connection so anyone close enough to pick it up can use it and I'm trying to close the connection so they would have to know my password to use it?
I was trying to get into the router the other day and it gave me invalid password consistently. I have hardware version B1 and firmware version 2.00NA. This had been working fine but this along with remote desktop no longer work.
I did some testing in WLC in our company wireless network.However, after my 3 hours testing, I had tried to login WLC again by GUI and SSH. The admin username and password does not work any more. All Read only and Guest Account did not work as well.Is any one had this issue before? Is there a restriction for access to WCL per 3 hours or one day? By the way, I did not change any password.
Just bought the N150 router. Trying to enter the router setup for the first time. I leave the password blank like it tells me to, but it says i have an incorrect password. Tried pressing reset button for 10 seconds, but get same result.
I have successfully installed a DCS-930L camera. However, when I add a second DCS-942L camera everything stops when I enter my existing account and password stating that they are incorrect (which they are not). The answer I get is: "Invalid e-mail and password combination".
Two 5520 firewall configuration of the failover and SSH, the first remote landing SSH, can use user and password successful landing, again landing, to prompt the user name password is invalid, what is the reason?
I have problem with Cisco ACS 4.0 "Windows" with core 4500 switch "cat4500-ENTSERVICESK9-M 12.2" the problem shows only on one device "x.x.x.x" the problem is " Authen failed-------badcred------External DB user invalid or bad password" i can see it in failed attempt. on the same side i can see in Passed Authentications for same record "Authen OK", i can login to the mentioned switch using my ACS credentials and not local database credentials
can debug this from ACS if not how can view the authentication records from core switch?
I bought a cisco router last week. The reseller said it is a brand new one. However, when I try to set it with console cable connecting to PC, the default password does not work. I tried to use control+break to get access to rommon for password recovery. The tera term pro displayed nothing at all! In thin case, what should I do to setup the router? Dose the reset button in the back work to restore the router to factory setting(which means i can use default username and password)?
I have a ASA 5520 which is intended to use as a VPN for clients using PDA, I think the PDA is a very old product that the VPN only support CHAP/ MS- CHAP, but seems it cannot connect the VPN, it will prompt "invalid username and password" (but in fact the username and password is valid when using PAP), below is the log i captured from the ASDM when the PDA is connecting the VPN. when i tried to connect it in windows PC, I also have the same issue if the VPN setting is using MS-CHAP, if I choose PAP, it can connect with no problem. But the PDA has no option of PAP. [code]
I am trying to setup ATT DSL modem through D-Link router Dir-615. I was instructed to use PPPoE and setup username and password in router. When I do, the router does not save my network password, but reverts back to some hidden password. I have tried changing it in Tools, but it keeps reverting. I'm sure this is why I cannot access the internet.
My Multi-media tab is not taking my wireless password? I have a d'link DIR-601; I reset the password using the web interface, but no matter what I try it doesnt link to my tab.What am I doing wrong ?
I just acquired an Ipod Touch and am trying to set it up to connect to my exisintin DIR-615 router. It is about one year old, but I have misplaced all the info I had on it, including any password info. Trying to use the blue lit button on the right side of the router does not allow access to the Ipod, nor my daughter's Apple computer.
Are there changes I need to make or special procedures for Apple products?
i have a LINKSYS WRT54G router .. i bought an apple ipod touch recently and i am unable to connect it to my wifi network. My ipod detects the wifi network but when i select it , it asks for password. now i dont know which password is this bcoz everytime i poer on my computer or laptop i never type a password b4 accessing internet.. it is auto connected. i know the admin password for my router but that is denied by ipod to connect to internet. Is there any other password we have to give for connecting deveices through LINKSYS or some changes i need to do in my connection ?
IPOD Touch 4G that will not connect to internet. it sees the network, requests a password but will not connect. Have been entering the same 8 character password the router uses.
