I have an old Dlink DI-604 that I'd like to configure to work as a switch. I think this is possible but not sure how to do it. Switches are cheap but if I could save a few bucks with some tweaking I'd prefer that. Plus I figure I'd learn a bit about networking.Dlinks site on the DI[URL]Uverse and I'm out of wired ports on the Residential Gateway. I would like 2 more ports to network my PC and NAS, so my laptop and Xbox can access their files.
I am testing rogue on wire using 5508 WLC and , I have a dedicated AP configured as rogue detector and configured the switch port where the Rogue detector is connected as trunk. I have plugged in an autonomous AP with open authentication to the same switch so that it can act as a rogue. On the WLC, I can see that Autonomous AP as rogue on Wire. But along with that I am seeing another AP as rogue on wire, even though i have plugged in only one Autonomous AP to the switch.
I have Dlink N300 router and also WRT54G2 router now with DD-WRT firmware, configured as a repeater.I have a PPPoE connection through Dlink router and want to extend signals farther, hence want to use Linksys (WRT54g2) as a repeater.I have set up the linksys as repeater but dont know how to check if its communicating with my Dlink and also I not able to get internet connection from the repeater.
I'm having issues with SSH on my 3750G-12S. I'm not able to SSH to another switch when VRFs are configured.I've tried ip ssh source-interface, ssh -vrf doesn't exsist and I've upgraded the IOS to the latest version.
such as the SLM2048T can be configured as an managed switch. Our schools have laptop carts and we want to put switches in the carts so that the laptops will be plugged into the network when not in use and software installs, updates, etc. can be pushed to the laptops while they're in the cart instead of waiting for them to be taken out, powered on and pushed over wireless. I can find a 10/100 48-port unmanaged switch, but I really want a gigabit unmanaged switch, but they don't seem to exist so I was wondering if a managed switch can be configured and used as an unmanaged switch. I don't want to have to assign a static IP address to the switch.
I have a named aggregate policer configured on a 4948 switch running IOS 12.2(53)SG2 but can't seem to be able to monitor it using SNMP as I can't locate the OIDs (using OIDView) - I'm okay with CB and PB QoS.
I've been tasked with finding all switch ports that are configured as Trunks. We plan to use LMS 4.2 to push (via Netconfig) new interface level commands to all user (non-trunked) ports. From my experience, this poses a problem because we do not know which ports are configured as trunks -vs- user ports.
Using Netconfig is not going to be easy since there is no way to script this. It would be great if I could run a show command on a switch and then have CWSI peform a change based upon the output.In other words, we need a way to run a job based upon the output of a command.
We have a 3560 switch behind a ASA 5510 at a site that we are trying to access via telnet over the internet, we find out the switch does not have a default gateway configured. So I configure the following rule on the 5510: [code] Try accessing the switch, and all is good. One of our change control steps is to identify any others are connected to the device via: [code] I see the connection and show users command return 172.16.30.15, as expected. How is it possible that address can connect to that switch.
I currently have a Cisco 2621 powering a network at our co-location facility... It's a simple setup and is working well. The colo provides a redundant HSRP uplink, so I have their two uplinks going into a Dell switch. From that Dell switch I have a uplink into FastEthernet0/0 on the 2621, configured with my routing network, and then FastEthernet0/1 gets an address from my block of routable IP. FastEthernet0/1 then plugs into another Dell switch where I have all my servers connected. The servers get public routable IP addresses and use the address on FastEthernet0/1 as their default gateway.
It's time to upgrade off the 2621, so I aquired a Cisco 2811 which has two FE interfaces, as well as a modular HWIC-4ESW switch. My question is, can I get rid of the Dell Switch A in the setup above and just use the internal switch on the 2811 to accomplish the same thing? And I if I did this, would my two uplinks from the colo plug into ports 1 and 2 of that HWIC, and then port 3 would physically connect into FE 0/0? Or can I logically do that via configuration in the Cisco? I'm not sure how all this works and haven't received the new router yet, so I thought I'd get a head start and reach out to the experts.
My second question is unrelated, but each port on the HWIC switch cannot be configured as a network interface right? I'm pretty sure they can't as they aren't considered network interfaces but just thought I'd ask.
how my switches are configured, a cisco 3750 and a cisco 4506.[code] i can ping the gateway from the 3750 however cannot get anything past that or enything to it.
we have cisco 6500 series switch and configured port channel on both switches with 2 gig interfaces on both switches.
When we enable the port channel mode to as desirable to the interfaces on both side and applied the port channel to physical interfaces switch will go down and if we remove on any one side switch will come up. we have enabled globally the following commands. [code]
I have a network which was recently switched from dsl to comcast. The default network is 10.1.10.1. The dhcp is working with the 5 or 6 installed pc's. All pc's are running xp professional.I inserted the dlink 4 port switch to add a new port by inserting it between the router and a pc.
We have a DHCP SERVER implemented in a cisco router 2610.This router is connected to a switch cisco 2960 configured as DHCP SNOOPING. At the switch appear the next log message: [code] The ip address: 10.100.200.1 belongs to DHCP SERVER configured at router cisco 2610. What to do so these log messages does not appear any more? Do I need to do some configuration changes at some switch or router?
We setup a home network in our new house but we have a problem with limited connectivity in specific configuration.
There is few situations to describe the problem :
1. If I connect my computer directly to the modem I can access to the internet. (modem --> computer = internet OK)
2. If i connect the ethernet cable (in the wall) between my modem and RJ45 jack in the living room and connect my computer directly to the RJ45 I can access to the internet. (modem --> cat6 cable in the wall --> computer = internet ok)
3. If I connect my router directly (without the cat6 cable in the wall) to the modem and my computer to the the router I can access to the internet. (modem --> router --> computer = internet ok)
4. If i connect the ethernet cable (in the wall) between my modem and RJ45 jack in the living room and connect to router to the RJ45 and my computer to the router I CANNOT access to the internet. (modem --> cat6 cable in the wall --> router --> computer = internet access problem)
5. If i connect the ethernet cable (in the wall) between my modem and RJ45 jack in the living room and connect to a swith to the RJ45 and my computer to the switch I can access to the internet. (modem --> cat6 cable in the wall --> switch --> computer = internet OK)
With those tests I am not able to figured out what is the problem... router is working in situation #3. cable in the wall is ok in situations #2 and 5. How to make my router working when connected to the RJ45 jack in the living room.
There is my component : Router --> D-Link WBR-2310 Switch --> Trendnet TE100-S5 Modem --> Thomson DCM475 Cable in the wall --> Homemade with 568A standard in both end.
I have Cyber cafe, And i'm having a problem with My 24 port Dlink "DES 1024d" switch, which has been misbehaving for few months, it looses connectivity to a pcsometimes.....when i reboot the pc, then it works again, But it keep losing connectivity to the other pc's, not at the same time, every time loses connectivity to a different pc.
I've had my network up and running for several years with no issues. Last week I upgraded my router to a Dlink 826L and now anything connected to my downstream Dlink DSS16+ can't be accessed.
I have been putting up with rubbish wireless signal down one end of my house now for quite some time. So I thought I have a spare wireless router and I could put it down there but I am sure ts not as easy as just plugging it and away you go.
Network Setup
Router 1 is a D-Link DIR-655 Router 2 is a D-Link DI-524
I need to know how to setup Router 2 so it basically become just a wireless access point
I am running Win 7 32-bit for my OS. I am on a desktop PC. I have a Internet modem only without the router. I have a Motorola SurfBoard SB5101.When I go into the Network Connections and do a diagnose. I get the following message. I tried doing netsh int ip reset reset.txt, and restart my PC, but it doesn't fix the error.Your computer appears to be configured, but the device or resource (DNS Server) is not responding.
I have configured Squid on my system having Windows 7. I didn't missed any steps. In Services it is showing Squid running.But my internet is running directly without any proxy settings. And when i change to proxy settings at port 3128, internet stops working. I had installed earlier and it was working fine. but now I am also using ICS to share internet connection from a broadband to a lan through my system.
We have a network based from a server where data is stored, such as Quickbooks files, and an employee has a laptop instead of a workspace. He needs to be able to access the Quickbooks file from his computer- we are currently using Remote Desktop Connection, however it is proving to be quite complicated for him and I need to know how to set it up. I know how to set up Quickbooks and all- the issue is with adding his laptop to the workgroup.
I have a router that I have not used for a year or so...I just recently moved to a new location and was trying to set it up...I completed the set up disk several times but I keep getting an error that says my router is connected but there is no internet access...When I plug the port directly to my PC I have internet...The router that I am using is Linksys WRT54G...I have even tried resetting to factory settings and I still can't get it to work.
I need to re-configure the passphrase configured on my HP printer.How do you run the wireless network set-up in order to re-enter my wireless network WPA security passphrase?
I purchased a Cisco 520 and am trying to set it up on my home network.Its ADSL PPPoA for WAN.I am trying to setup 2 LANS. One General Network,One DMZ for webhosting.Now, since this router has 4 ethernet ports, i assumed i did not need VLANS. Except when i try configure an interface with an IP address i get this error: % IP addresses may not be configured on L2 links.Now. Ive looked around on the internet about this error. And it seems that since these interfaces are not Layer 3 interfaces,they need to be associated with VLANS.This would be OK. Except this requires an IP address on an interface on the router! Back to square one.
I am having an ASA 5510 and have configured Clientless SSL VPN in it. Now I need to allow my SSL VPN user to access on a particular application(like mspaint.exe for example).When the user login to the SSL VPN, he should see only the particular aplication or must be able to access on the particular application.
I purchased 2 Cisco WAP4410N and i configured them on the network as 192.168.1.241 and .242.I see both SSIDs i created and they are named Cabo1 and Cabo2.
When i initially did the setup I was able to log into the webbased interface through both ip addresses.
I just tried again now, and Im able to log into the interface for .242 but not the .241. I am connect to the router with .241 via wireless because it is with the SSID of Cabo1.
I would like to know if we can use the following card i.e. WS-X6704-10GE along with SUP-2T which will be configured in VSS.
This line is supported with SUP-2T, however not sure if the sup 2t will be configured in VSS. If any supporting document can be provided for the same , that would be great.
If this is supported than whether i would be getting line rate/non blocking capacity with WS-X6704-10GE. Since SUP-2T provides 80 Gbps bandwidth per slot.
Can a PA-1GE module in a 7206VXR with an NPE-G2 be configured to negotiate/work with a 100mbps Vendor provided Ethernet Port? The router sees the interface but it is in up/down.
I'm trying to automate our rollout process with kiwi cat tools. I want to copy a file via TFTP or FTP: Cisco tftp menu knows the latest ip address which it was connected to.
