Cisco WAN :: 2811 HWIC Switch Cannot Be Configured As A Network Interface
Apr 14, 2012
I currently have a Cisco 2621 powering a network at our co-location facility... It's a simple setup and is working well. The colo provides a redundant HSRP uplink, so I have their two uplinks going into a Dell switch. From that Dell switch I have a uplink into FastEthernet0/0 on the 2621, configured with my routing network, and then FastEthernet0/1 gets an address from my block of routable IP. FastEthernet0/1 then plugs into another Dell switch where I have all my servers connected. The servers get public routable IP addresses and use the address on FastEthernet0/1 as their default gateway.
It's time to upgrade off the 2621, so I aquired a Cisco 2811 which has two FE interfaces, as well as a modular HWIC-4ESW switch. My question is, can I get rid of the Dell Switch A in the setup above and just use the internal switch on the 2811 to accomplish the same thing? And I if I did this, would my two uplinks from the colo plug into ports 1 and 2 of that HWIC, and then port 3 would physically connect into FE 0/0? Or can I logically do that via configuration in the Cisco? I'm not sure how all this works and haven't received the new router yet, so I thought I'd get a head start and reach out to the experts.
My second question is unrelated, but each port on the HWIC switch cannot be configured as a network interface right? I'm pretty sure they can't as they aren't considered network interfaces but just thought I'd ask.
View 11 Replies
ADVERTISEMENT
Apr 20, 2012
I am trying to configure a newly installed HWIC-4ESW on a 2811 router to bridge to the FE 0/0 interface. Currently, I have a cheap switch connected to FE 0/0 which in turn connects to all the phones, however now I just want to connect all the phones to the HWIC and have it internally bridge to FE0/0 for the connectivity to CME, etc.
View 5 Replies
View Related
Jan 9, 2012
we have cisco 6500 series switch and configured port channel on both switches with 2 gig interfaces on both switches.
When we enable the port channel mode to as desirable to the interfaces on both side and applied the port channel to physical interfaces switch will go down and if we remove on any one side switch will come up. we have enabled globally the following commands. [code]
View 10 Replies
View Related
Feb 24, 2013
We have configured new 2911 router with HWIC-2T with it.However we are seeing serial interfaces up, but can hardly ping other end. Again we are seeing a lot of CRC errors on serial interface.
But if we connected same cable, with other old router 2811, it works fine. Confiuration is same on both the routers. [code]
View 2 Replies
View Related
Jul 21, 2011
I am testing rogue on wire using 5508 WLC and , I have a dedicated AP configured as rogue detector and configured the switch port where the Rogue detector is connected as trunk. I have plugged in an autonomous AP with open authentication to the same switch so that it can act as a rogue. On the WLC, I can see that Autonomous AP as rogue on Wire. But along with that I am seeing another AP as rogue on wire, even though i have plugged in only one Autonomous AP to the switch.
View 3 Replies
View Related
May 9, 2012
i have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies
View Related
Jun 12, 2011
I have a Cisco 2811 router with c2800nm-adventerprisek9_sna-mz.124-2.T6.bin as IOS and i wsh to install this HWIC 4port to increase available ports on my router. Wish to know if this is going to work,that is, if i installed it the IOS available will recognise this card
View 4 Replies
View Related
Sep 7, 2009
I would like to ask if a cisco 2811 running on an ios c2800nm-adventerprisek9-mz.124-25a.bin should be able to make an HWIC-1FE card work? I am also not detecting the card on any show commands. Plus i am seeing that all the LEDs (FDX/COL,100 and LINK/ACT) are lit steadily even though there is no cable attached to it, is it safe to say that the card could be defective?
View 6 Replies
View Related
Oct 26, 2011
i am currently trying to configure a four port ISDN BRI interface on a Cisco 2811 router.Upon upgrading to a later version of IOS, c2800nm-advipservicesk9-mz.124-25d.bin, access to the HWIC-4B-S/T module is lost, the router no longer detects it. In fact iI can only get the router to detect the module using the original IOS version c2800nm-advipservicesk9-mz.124-20.YA3.bin.
Is there some special feature needed in the IOS code to support these modules, if so what would be a suitable version/train to upgrade to?I have tried using the Cisco Software advisor tool but it generates an error when searching on a hardware configuration containing this module type.
The reason for upgrading the code is we have a potential bug with the current version which appears to be preventing the BRI interface syncing up with the providers switch (switch type correctly defined and provider confirms isdn line has been provisioned correctly).
The debug error seen is:
GMT: ISDN BR0/0/0 SERROR: L2_Go: at bailout DLCB is NULL
L2: sapi 63 tei 127 ces 0 ev 0x650
My main question though is why the module is not being detected after a code upgrade and if there is a specific code version/train needed to support this module in a 2811?
View 11 Replies
View Related
Jan 23, 2012
I am adding another ISP (and plan to use BGP). I am looking at having two 2811's with one connected to each ISP, or a single 2811 (with an additional HWIC) connected to both ISPs. I am not sure if there is a best practices or an ideal configuration for this.
Currently I have:
ASA5510 ---> 2811 ---> ISP_A
Should I purchase another 2811 for ISP_B and connect it to an available port on the ASA? Or should I just purchase a HWIC-1FE and add ISP_B to the existing router?
I see some advantages to both, but not sure the best way to go. Of course, I could be looking at this wrong and if I plan on buying another router then maybe I should use HSRP and both routers should connect to both ISPs.
View 2 Replies
View Related
Dec 12, 2010
Is there an ethernet WIC/HWIC that supports NAT for the 2811. I have one 4 port 10/100 card but it doesn't support NAT overload.
View 5 Replies
View Related
May 19, 2011
I have a 2811 router runnning IOS 12.4(21) and have added an HWIC 1FE card to slot 2. But the card doesnot show up in the router and all the three lights on the HWIC card is steady green. I have gone through some cisco documentation and found that i have to upgrade the IOS.
I have few questions before doing the upgrade.
1. Which IOS version should I upgrade to?
2. Will this erase my exisitng running configuration ? I have VPN services, PPPoATM, PBR etc.. all running on this router at present.
3. Presently i have a 128 MB CF card on the router. Will this be enough or do i need to upgrade this card also? Can i choose an IOS which will fit into this card otherwise while keeping all existng features?
4. I want to use the HWIC card for the ISP's internet service through PPPoE. Will this be possible with the upgraded IOS ?
View 1 Replies
View Related
May 10, 2011
I am trying to connect HWIC-2FE Card to my Cisco 2811 Router. The router is unable to detect the card. I get the following error message:
' %GT96K_FEWAN-1-UNKNOWN_WIC: NM slot 0, wic card has an unknown id 53BPort Statistics for unclassified packets is not turned on.'
View 2 Replies
View Related
Jun 3, 2013
I have a module of HWIC-4ESW installed into Cisco 2811 router where 3 WAN link is terminited. Suddently WAN links stopped working from last night. I have performed shutdown and no shutdown in the interface but still the the WAN link was not working. After performing a reboot the WAN link started working. No error logs were generated while the WAN link was down.
View 4 Replies
View Related
Oct 31, 2010
[URL]The Cisco 2811 does not support the HWIC-4T1/E1 module. But, I installed HWIC-4T1/E1 on the 2811 running 124-24.T2.
View 3 Replies
View Related
Jan 24, 2013
Just double-confirm that 2811 is compatible with HWIC-2FE based on your experience? Which IOS is compatible with HWIC-2FE? [URL]
View 3 Replies
View Related
May 31, 2011
I'm looking for a HWIC card that will support SC fiber connections for a 2811. I know of the HWIC-1GE-SFP but this one only support the LC connections.
View 2 Replies
View Related
Jul 31, 2012
I have cisco2811 and HWIC-1CE1T1-PRI in the main office are using to connect 10 branches ( 10 ISDN lines) for Data.
I have available channels in the used E1 so I can use them for voice using PVDM2-64 ?
View 3 Replies
View Related
Nov 15, 2011
I configured a 2811 series router for dmvpn. My two tunnels are up but one of the tunnel is flapping with this message.
View 4 Replies
View Related
Mar 16, 2010
I've been collecting information on principles of SHDSL connection. I have found plenty of examples on how to configure only one SHDSL link. Very soon I'm going to the site to install two independent SHDSL links in Cisco 2811 which has one Cisco HWIC-2SHDSL module, so I can route one type of traffic through one connection and another type of traffic through another. Both SHDLS links have static IP addresses and probably different VPI/VCI values. how to install two SHDSL links into one HWIC-2SHDSL module, set one value for VPI/VCI on one link and another value for VPI/VCI on another link, also set one IP address on one link and another IP adddress on another link?
View 13 Replies
View Related
Jul 13, 2011
I have a scenario where multiple branches are connected to Head Office via DSL links. The branches are located in differenct exchanges, everyone once in a while ALL branches go down at the exact same time except 3 branches and those 3 branches don't have ATM interface on the router, rather they have external DSL modem, all other branches that face the disconnection (for couple of minutes) have either HWIC-1ADSL-M or HWIC-2SHDSL and the DSL line is directly plugged into the card. [code]
I tried so many solutions like adding "operating-mode auto" command under the subinterface, IOS upgrade, changed dynamic routing protocol from EIGRP to OSPF... Nothing worked, on the logs of the router it just shows "EIGRP neighbor down", at the time of the problem I can't ping any of the affected branches on their WAN ATM interface although it stays physically "up up".Could the problem be a missing command that I need to add under the subinterface? Something maybe related to clocking or timeout or..?Note that hte problem occurs randomly, every few days, sometimes every 10 days, and all branches with ATM interface go down at the exact same time.
View 5 Replies
View Related
Apr 6, 2010
I have problem with HWIC-3G-GSM configuration. The cellular interface doesn't get IP from ISP.The configured profile is always inactive.cellular 0/2/0 gsm profile create 1 m2m.plusgsm.pl chap plusgsm plusgsm
View 3 Replies
View Related
May 19, 2013
I'm having problems to ping through interface atm 0/0/0 which is releated to a card HWIC-2SHDSL . The router I have is a 1941. I dont know what to do. [code]
View 8 Replies
View Related
Jan 23, 2011
I have some issue on Card Hwic-D-9ESW with Router 2821, i was install card 9ESW in to router 2821 on slot 2 and 3. After I show run, the Cisco Router 2821 have interface F0/3/0 - F0/3/8.and i configure V lan already and interface up also.
When i connect PC to port F0/3/0, the interface is up, but i cannot pint go interface, i mean it request time out. My question is, Is it correct that i install card into slot 2 and 3?
What is the problem all port up but i cannot ping to interface?
Note: the same V lan
View 2 Replies
View Related
Feb 3, 2013
On an AIRONET 600 AP (officeExtend) with the remote LAN interface is configured to use 802.1x authentication:If a Cisco IP Phone is connected, 801.x authentication challenges for credentials. The AP does not seem to have a way to detect that this is an IP Phone and to skip the challenge (as Cisco switches/routers would do) Is there any way around this? Can the remote LAN interface be configured to skip authentication for IP Phone and only authenticate PCs etc..?
View 5 Replies
View Related
Apr 5, 2011
We have Cisco 2811 router with Hwic-3g-HSPA card. When I configure the system everything was fine. Around two weeks 3g interface works, got IP address ,everyting was fine.Yesterday I check the sytem and I saw that cellular interface become reseting itself, without stoping.We have 2 g.shdls and one 3G connection on the same router. dialer 0 ansd dialer 1 for g.shdls, and dilaer 3 for 3G connection. [code]
View 1 Replies
View Related
Jun 5, 2011
my office is looking in ordering a HWIC-1FE to supply our cisco 1841 router with a second ISP connection. i wanted to find out if this card support load balancing and fail over? not sure if fail over is the right terminology so ill explain, i need it so that if one ISP connection goes down (as it does often) it fails over to the second ISP.
View 3 Replies
View Related
May 1, 2012
I have configured policies to shape the traffic on the interface of cisco 7206 router. Now my managemet wants to configure these policies on time based ie policy should be applicable during specified time period onle. Is it possible? if yes how to configure it?
View 11 Replies
View Related
Jan 26, 2011
I'm having issues with SSH on my 3750G-12S. I'm not able to SSH to another switch when VRFs are configured.I've tried ip ssh source-interface, ssh -vrf doesn't exsist and I've upgraded the IOS to the latest version.
View 4 Replies
View Related
Jan 23, 2012
I have an old Dlink DI-604 that I'd like to configure to work as a switch. I think this is possible but not sure how to do it. Switches are cheap but if I could save a few bucks with some tweaking I'd prefer that. Plus I figure I'd learn a bit about networking.Dlinks site on the DI[URL]Uverse and I'm out of wired ports on the Residential Gateway. I would like 2 more ports to network my PC and NAS, so my laptop and Xbox can access their files.
View 4 Replies
View Related
Oct 4, 2012
Can We use Cisco HWIC-4ESW as no Switch Port.
View 5 Replies
View Related
Feb 25, 2013
such as the SLM2048T can be configured as an managed switch. Our schools have laptop carts and we want to put switches in the carts so that the laptops will be plugged into the network when not in use and software installs, updates, etc. can be pushed to the laptops while they're in the cart instead of waiting for them to be taken out, powered on and pushed over wireless. I can find a 10/100 48-port unmanaged switch, but I really want a gigabit unmanaged switch, but they don't seem to exist so I was wondering if a managed switch can be configured and used as an unmanaged switch. I don't want to have to assign a static IP address to the switch.
View 1 Replies
View Related
Oct 17, 2011
I have a named aggregate policer configured on a 4948 switch running IOS 12.2(53)SG2 but can't seem to be able to monitor it using SNMP as I can't locate the OIDs (using OIDView) - I'm okay with CB and PB QoS.
View 1 Replies
View Related