Cisco WAN :: Interface Atm 0 / 0 / 0 Which Is Related To Card HWIC-2SHDSL

May 19, 2013

I'm having problems to ping through interface atm 0/0/0 which is releated to a card HWIC-2SHDSL . The router I have is a 1941. I dont know what to do. [code]

View 8 Replies


ADVERTISEMENT

Cisco WAN :: HWIC-2SHDSL Disconnection With ATM Interface

Jul 13, 2011

I have a scenario where multiple branches are connected to Head Office via DSL links. The branches are located in differenct exchanges, everyone once in a while ALL branches go down at the exact same time except 3 branches and those 3 branches don't have ATM interface on the router, rather they have external DSL modem, all other branches that face the disconnection (for couple of minutes) have either HWIC-1ADSL-M or HWIC-2SHDSL and the DSL line is directly plugged into the card. [code]
 
I tried so many solutions like adding "operating-mode auto" command under the subinterface, IOS upgrade, changed dynamic routing protocol from EIGRP to OSPF... Nothing worked, on the logs of the router it just shows "EIGRP neighbor down", at the time of the problem I can't ping any of the affected branches on their WAN ATM interface although it stays physically "up up".Could the problem be a missing command that I need to add under the subinterface? Something maybe related to clocking or timeout or..?Note that hte problem occurs randomly, every few days, sometimes every 10 days, and all branches with ATM interface go down at the exact same time.

View 5 Replies View Related

Cisco WAN :: Configuring HWIC-2SHDSL Card In A 2911 For CO Mode Operation?

Dec 12, 2011

I am trying to configure a shdsl port on a 2911 router for CO mode of operation.The dsl-group auto command does not seem to change the port to operate in CO mode and the link will not come up to a remote router that has a card installed operating in CPE mode.The configuration I have applied for the shdsl controller is.
 
controller SHDSL 0/1/0
dsl-group auto
!
!
 
Do I need to use a HWIC-4SHDSL card for the CO mode operation?

View 3 Replies View Related

Cisco WAN :: 1841 Router - HWIC Interface Card - Cannot See Interface In Configuration File

May 9, 2012

i have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?

View 8 Replies View Related

Cisco WAN :: 2811 / HWIC-2SHDSL - How To Configure Two Independent SHDLS Connections Through One

Mar 16, 2010

I've been collecting information on principles of SHDSL connection. I have found plenty of examples on how to configure only one SHDSL link. Very soon I'm going to the site to install two independent SHDSL links in Cisco 2811 which has one Cisco HWIC-2SHDSL module, so I can route one type of traffic through one connection and another type of traffic through another. Both SHDLS links have static IP addresses and probably different VPI/VCI values. how to install two SHDSL links into one HWIC-2SHDSL module, set one value for VPI/VCI on one link and another value for VPI/VCI on another link, also set one IP address on one link and another IP adddress on another link?

View 13 Replies View Related

Cisco WAN :: 2821 Router / Card Hwic-D-9ESW - Cannot Ping To Interface

Jan 23, 2011

I have some issue on Card Hwic-D-9ESW with Router 2821, i was install card 9ESW in to router 2821 on slot 2 and 3. After I show run, the Cisco Router 2821 have interface F0/3/0 - F0/3/8.and i configure V lan already  and interface up also.

When i connect PC to port F0/3/0, the interface is up, but i cannot pint go interface, i mean it request time out. My question is, Is it correct that i install card into slot 2 and 3?

What is the problem all port up but i cannot ping to interface?

Note: the same V lan

View 2 Replies View Related

Cisco Wireless :: HWIC-3G-HSPA Card Was Working Properly But 3G Interface Resets

Apr 5, 2011

We have Cisco 2811 router with  Hwic-3g-HSPA card. When I configure the system everything was fine. Around two weeks 3g interface works, got IP address ,everyting was fine.Yesterday I check the sytem and I saw that cellular interface become reseting itself, without stoping.We have 2 g.shdls and one 3G connection on the same router. dialer 0 ansd dialer 1 for g.shdls, and dilaer 3 for 3G connection. [code]

View 1 Replies View Related

Cisco WAN :: 1841 / High Speed WAN Interface Card (HWIC) Supported Features?

Jun 5, 2011

my office is looking in ordering a HWIC-1FE to supply our cisco 1841 router with a second ISP connection. i wanted to find out if this card support load balancing and fail over? not sure if fail over is the right terminology so ill explain, i need it so that if one ISP connection goes down (as it does often) it fails over to the second ISP.

View 3 Replies View Related

Cisco WAN :: HWIC Card For 1861?

Dec 5, 2011

if the card HWIC-1SER is the equivalent card HWIC-1T for 1861 router?

View 3 Replies View Related

Cisco WAN :: Finding A HWIC Card For 2901?

Dec 18, 2012

I was looking an HWIC card for CISCO2901-SEC/K9. We have one internet connection (ADSL) current.Now we want to backup internet connection from cable service provider. I will implement IPSec on this HWIC.
 
What HWIC cards can I choose for this router?

View 6 Replies View Related

Cisco WAN :: 1841 - VPN Options With 3G HWIC Card

Aug 19, 2012

I've been given an 1841 with a 3G HWIC card installed to test with.  I need to set up some sort of VPN to our ASA, the problem is though these 3G cards get a random public IP, so what options do I have to create a VPN tunnel from this router to the ASA without the 1841 getting a static public IP?

View 3 Replies View Related

Cisco WAN :: Adding A HWIC 1FE Card To 2811 Router?

May 19, 2011

I have a 2811 router runnning IOS 12.4(21) and have added an HWIC 1FE card to slot 2. But the card doesnot show up in the router and all the three lights on the HWIC card is steady green. I have gone through some cisco documentation and found that i have to upgrade the IOS.
 
I have few questions before doing the upgrade.
 
1. Which IOS version should I upgrade to?

2. Will this erase my exisitng running configuration ? I have VPN services, PPPoATM,  PBR  etc.. all running on this router at present.

3. Presently i have a 128 MB CF card on the router. Will this be enough or do i need to upgrade this card also? Can i choose an IOS which will fit into this card otherwise while keeping all existng features?

4. I want to use the HWIC card for the ISP's internet service through PPPoE. Will this be possible with the upgraded IOS ?

View 1 Replies View Related

Cisco WAN :: Router 2811 Can't Detect HWIC-2FE Card?

May 10, 2011

I am trying to connect HWIC-2FE Card to my Cisco 2811 Router. The router is unable to detect the card. I get the following error message:
 
' %GT96K_FEWAN-1-UNKNOWN_WIC: NM slot 0, wic card has an unknown id 53BPort Statistics for unclassified packets is not turned on.'

View 2 Replies View Related

Cisco WAN :: Which Type Of HWIC Card Should Use In 2911-sec / K9 Router

Feb 14, 2012

I have cisco 2611 + NM1E , and i want to trade in for a cisco 2911 security router + HWIC4 Card.Which type of HWIC card should i use in the cisco2911-sec/k9 router?

View 1 Replies View Related

Cisco Infrastructure :: Connect Two Router With One HWIC-4ESW Card?

Sep 2, 2011

How Can I connect two router with one HWIC-4ESW card , I have Problem with this  because when I tried to do , I received the message I can´t  configure IP address on L2.  The idea is to connect two routers  with   /30.

View 2 Replies View Related

Cisco WAN :: HWIC Card That Will Support SC Fiber Connections For 2811

May 31, 2011

I'm looking for a HWIC card that will support SC fiber connections for a 2811.  I know of the HWIC-1GE-SFP but this one only support the LC connections.

View 2 Replies View Related

Cisco Switching/Routing :: 3845 With HWIC-2FE / Card Fails To Show Up

Jan 16, 2008

I have this card installed onmy 3845 running version 12.4(18). But this card fails to show up.

here is what I found in a show tech.

WIC Slot 0:
     Unknown WAN daughter card
     WIC module not supported/disabled in this slot
     Hardware Revision        : 2.0
     Top Assy. Part Number    : 800-27738-02
     Part Number              : 73-10677-02
     Board Revision           : B0
     Deviation Number         : 0
     Fab Version              : 02
     PCB Serial Number        : FOC********
     RMA Test History         : 00
     RMA Number               : 0-0-0-0
     RMA History              : 00
     Product (FRU) Number     : HWIC-2FE         
     Version Identifier       : V01
     CLEI Code                : COUIAFUCAA
     Base MAC Address         : 001a.6c70.260b
     MAC Address block size   : 2
     Connector Type           : 01
     EEPROM format version 4
     EEPROM contents (hex):(code)

View 4 Replies View Related

Cisco Wireless :: Configure 28xx Series Router With HWIC-AP Card As Wi-Fi Client?

Mar 20, 2013

Is there a way to configure a 28xx series router with a HWIC-AP card as a wireless client instead of a wireless access point?  There isn't a network drop in the location that I need to place a router, but there is an active Access Point that reaches the area.

View 1 Replies View Related

Cisco WAN :: HWIC-3G-GSM Configuration / The Cellular Interface Doesn't Get IP From ISP

Apr 6, 2010

I have problem with HWIC-3G-GSM configuration. The cellular interface doesn't get IP from ISP.The configured profile is always inactive.cellular 0/2/0 gsm profile create 1 m2m.plusgsm.pl chap plusgsm plusgsm

View 3 Replies View Related

Cisco WAN :: 2811 HWIC Switch Cannot Be Configured As A Network Interface

Apr 14, 2012

I currently have a Cisco 2621 powering a network at our  co-location facility... It's a simple setup and is working well. The colo  provides a redundant HSRP uplink, so I have their two uplinks going into  a Dell switch. From that Dell switch I have a uplink into  FastEthernet0/0 on the 2621, configured with my routing network, and  then FastEthernet0/1 gets an address from my block of routable IP. FastEthernet0/1 then plugs into another  Dell switch where I have all my servers connected. The servers get public routable IP addresses and use the address on FastEthernet0/1 as their default gateway.
 
It's time to upgrade off the 2621, so I aquired a Cisco 2811 which has two FE interfaces, as well as a modular HWIC-4ESW switch. My question is, can I get rid of the Dell Switch A in the setup above and just use the internal switch on the 2811 to accomplish the same thing? And I if I did this, would my two uplinks from the colo plug into ports 1 and 2 of that HWIC, and then port 3 would physically connect into FE 0/0? Or can I logically do that via configuration in the Cisco? I'm not sure how all this works and haven't received the new router yet, so I thought I'd get a head start and reach out to the experts.
 
My second question is unrelated, but each port on the HWIC switch cannot be configured as a network interface right? I'm pretty sure they can't as they aren't considered network interfaces but just thought I'd ask.

View 11 Replies View Related

Cisco WAN :: Configure Newly Installed HWIC-4ESW On 2811 Router To Bridge To FE 0 / 0 Interface

Apr 20, 2012

I am trying to configure a newly installed HWIC-4ESW on a 2811 router to bridge to the FE 0/0 interface. Currently, I have a cheap switch connected to FE 0/0 which in turn connects to all the phones, however now I just want to connect all the phones to the HWIC and have it internally bridge to FE0/0 for the connectivity to CME, etc.

View 5 Replies View Related

Cisco Switching/Routing :: Connecting Two 2951 Back To Back Through A HWIC-4T1 Card

Dec 4, 2011

What cable I need to connect two 2951 back to back through a HWIC-4T1/E1 card ?

View 1 Replies View Related

Cisco WAN :: 1721 Router With Ethernet Interface Card

Feb 25, 2011

I have cisco 1721 router so I installed an ethernet interface card so when I make show run I found that there is a fast ethernet 0 and ethernet 0 (which I installed) so i wand to make subinfaces of the etheernet 0 but I can't. I tried to make encapsulation dot.1q but it doesn't accept it.
 
Is Ethernet0 supported to generate subinterfaces?

View 3 Replies View Related

Network Interface Card - Can't Connect To Internet?

Sep 20, 2011

I recently install xp pro and update all necessary drivers for the computer.I also plug-in another network card, this nic is working but seem browsing the web is slower than the original network card comes with the motherboard. Before both network cards show up in (my network places). Now the network card comes with the motherboard doesn't show up, only the network card connection just installed.

I check the device manager both of the network adapters are there, check both of box that say place LAN on taskbar.This could be i have find and install revised intel chipset and lastest BIOS for the pc, now the hard drive activity LED doesn't lit and the ethernet controller has issue. Note when I plug in the cable to ethernet port (one built with pc) there's show both activity light and connection light, but can't connect to the internet.

pc info:
winxp pro sp3
pentium celeron
256 mb of memory
manufacturer: gateway

View 1 Replies View Related

Can't Connect To Anything Related To Facebook

Dec 28, 2012

I can't connect to facebook on any browser on this laptop. I can access it from my iphone and from my friends' laptops, but this one isn't letting me get to the page at all. It just turns up with "this webpage is not available" (same with firefox and ie) when i try to go to facebook. I tried running Malwarebytes and Mcafee, but neither of those found any problems. I can't connect to accounts associated with my facebook account either, like Wanelo or Elfster, and I can't connect to downloaded programs that I logged into with my facebook account such as Oovoo and facebook chat. The only thing I can connect to on this laptop is m.facebook.com, the mobile site.

View 1 Replies View Related

Cisco :: LMS 4.1 How To Troubleshoot System Related Stuff

Jan 21, 2013

I have been in charge of CW and now LMS 4.1. Since I am not a system engineer in profession, it has always been difficult for me to understand how to keep databases and log files in order and how to troubleshoot system related stuff, without causing any problems.I mean that besides setting jobs (device discovery, netconfig, usertracking, archiving and the like), what else do I need to check on a regularly basis, which jobs can I delete with safety, what kind o log rotation should I configure?For example, I have noticed that the ConfigMgmtServer.log is quite large (1,2 Gbytes).

View 10 Replies View Related

Cisco Switching/Routing :: 2811 - New Serial Card Interface Not Detected?

Mar 26, 2012

I have existing cisco 2811 (Version 12.4(3c)). I try to add a HWIC serial card into the router but the new HWIC is not detected. There is no new interfece shows up when i do show run. This HWIC is a new card just bought it.

View 7 Replies View Related

Retrieving Data Related To Router

Feb 23, 2012

I have a linksys wireless router and today I attempted to attach a epson wirellesss printer to the network. I used ssid and passwords I thought were correct and did not gain access. I want to know how I can retrieve the correct info. The data I used was from the initial setup of the router. I did have to swap it out during the warranty period and now have a replacement router.

View 1 Replies View Related

Cannot Install The Drivers For TrendNet TEW-423PI Network Interface Card

Mar 20, 2012

I cannot install the drivers for my TrendNet TEW-423PI network interface card. I am running Windows 7 64-bit with an Intel i7 2700k and an Asus motherboard. I have tried installing with the card already in the computer - no luck. Card out of the computer install and then shut off and put in - no luck. The instructions that come with the card say that after you install the program that instantly runs from the CD provided you should shut off the computer and install the card and when you turn the computer back on the drivers will install automatically. It has failed to do so and although I pulled all possible drivers from TrendNet's site it still stubbornly refuses to even recognize that there are drivers for it to install.

View 2 Replies View Related

Dell D60 With Built In Intel Wireless Card - No Network Interface?

Jan 19, 2012

My friend has a dell d600 with the built in intel wireless card. All of a sudden his computer no longer shows that there is a wireless interface in the computer and he needs this computer for work. I'm thinking the driver may need to be reinstalled but I'm not entirely sure if it's that or a hardware error that's causing this malfunction.

View 3 Replies View Related

Cisco Switches :: SG200-50P Boot And PoE Related Errors

Apr 11, 2013

I have a SG200-50P.  It had a problem with the PoE ports (didn't supply power to my Bosch POE security cameras) so I updated it to the latest firmware.  Now it does recognize the cemeras and supplies power to them.  However, there are a few problems:
 
1. The boot time is extremely long, maybe 15-20 minutes for it to become ready.  I've tried to reset to factory default settings, push the reset button for 30+ seconds, and disconnect all the ports.  The boot time was always very long.
 
2. Even thought it supplies power to the cameras, the PoE lights on the ports are not lit.
 
3. The log is filled with this error, posted every second.
 
21474345202013-Apr-12 11:40:23Alert%HAL_config_poe-A-POEFailDetected: POE ERROR(i2c_read_mem failed addr 0x12e6 dev_num 0 val 0x0) was detected: POE is Disabled untill Reset      21474345212013-Apr-12 11:40:22Alert%HAL_config_poe-A-POEFailDetected: POE ERROR(i2c_read_mem failed addr 0x139c dev_num 0 val 0x0) was detected: POE is Disabled untill Reset       
Occasionally it has his error.

View 5 Replies View Related

Cisco Firewall :: Configuration Changes Logging ASDM 8.4 Related?

Mar 1, 2012

I've run into an interesting problem.
 
-ASA: 8.4(2)
-ASDM: 6.4(5)
 
When I make a change at the CLI, syslog message ASA-5-111008 is generated and sent to the syslog servers, local buffer, and ASDM.When I make a change in ASDM, syslog message ASA-5-111008 is  generated and sent to the local  buffer and ASDM. It is NOT sent to the syslog server.

View 2 Replies View Related

Cisco WAN :: 1900 / 2900 / 3900 - Which Type Of Card Support Interface Slot

Nov 14, 2011

Cisco 1900 , 2900 and 3900 have Interface Slots and Service Module Slots , My question is which type of card is support this slot.

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved