I have cisco 2611 + NM1E , and i want to trade in for a cisco 2911 security router + HWIC4 Card.Which type of HWIC card should i use in the cisco2911-sec/k9 router?
View 1 RepliesI am trying to configure a shdsl port on a 2911 router for CO mode of operation.The dsl-group auto command does not seem to change the port to operate in CO mode and the link will not come up to a remote router that has a card installed operating in CPE mode.The configuration I have applied for the shdsl controller is.
controller SHDSL 0/1/0
dsl-group auto
!
!
Do I need to use a HWIC-4SHDSL card for the CO mode operation?
We have configured new 2911 router with HWIC-2T with it.However we are seeing serial interfaces up, but can hardly ping other end. Again we are seeing a lot of CRC errors on serial interface.
But if we connected same cable, with other old router 2811, it works fine. Confiuration is same on both the routers. [code]
I had purchased a HWIC-8A in an effort to provide terminal server capabilities into multiple routers. I had found a document that I thought would take me through the configuration but it doesn't appear that the command syntax is the same on the 2911's as it is in the document. Does any know how I would need to get this configured on the 2911 router?
Here is the document I was referencing
[URL]
I have a 2811 router runnning IOS 12.4(21) and have added an HWIC 1FE card to slot 2. But the card doesnot show up in the router and all the three lights on the HWIC card is steady green. I have gone through some cisco documentation and found that i have to upgrade the IOS.
I have few questions before doing the upgrade.
1. Which IOS version should I upgrade to?
2. Will this erase my exisitng running configuration ? I have VPN services, PPPoATM, PBR etc.. all running on this router at present.
3. Presently i have a 128 MB CF card on the router. Will this be enough or do i need to upgrade this card also? Can i choose an IOS which will fit into this card otherwise while keeping all existng features?
4. I want to use the HWIC card for the ISP's internet service through PPPoE. Will this be possible with the upgraded IOS ?
I am trying to connect HWIC-2FE Card to my Cisco 2811 Router. The router is unable to detect the card. I get the following error message:
' %GT96K_FEWAN-1-UNKNOWN_WIC: NM slot 0, wic card has an unknown id 53BPort Statistics for unclassified packets is not turned on.'
How Can I connect two router with one HWIC-4ESW card , I have Problem with this because when I tried to do , I received the message I can´t configure IP address on L2. The idea is to connect two routers with /30.
View 2 Replies View RelatedI have some issue on Card Hwic-D-9ESW with Router 2821, i was install card 9ESW in to router 2821 on slot 2 and 3. After I show run, the Cisco Router 2821 have interface F0/3/0 - F0/3/8.and i configure V lan already and interface up also.
When i connect PC to port F0/3/0, the interface is up, but i cannot pint go interface, i mean it request time out. My question is, Is it correct that i install card into slot 2 and 3?
What is the problem all port up but i cannot ping to interface?
Note: the same V lan
Is there a way to configure a 28xx series router with a HWIC-AP card as a wireless client instead of a wireless access point? There isn't a network drop in the location that I need to place a router, but there is an active Access Point that reaches the area.
View 1 Replies View RelatedAccording to specifications fo Cisco ISR G2 2911, it has got 4 EHWIC slots. But in [URL] appears that Cisco2911 supports only 2 HWIC-2FE or only 2 EHWIC-1GE-SFP-CU.
View 1 Replies View RelatedWe plan migrate an old existing WAN architecture based on legacy data serial links. These links will be consolidated on a E1 channalized card.
My question :
Is the HWIC-2CE1T1-PRI need a PDVM DSP ressources on router to oparate for data leased lines or no?
The VWIC3-1MFT-T1/E1 will be used for the backup dial in ISDN connexions? this type of cards a PVDM DSP ressources for data connexions or no?
ISR router are 2911.
I purchased a 2911 months ago to connect a remote site via T1 circuit.I think I might be missing some hardware to make this work on the remote end. Currently have a VWIC2-2MFT-T1/E1 card.Does this WIC actually work with this router? So no reference that this VWIC works with 2911.
View 1 Replies View Relatedi have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies View Relatedif the card HWIC-1SER is the equivalent card HWIC-1T for 1861 router?
View 3 Replies View RelatedI was looking an HWIC card for CISCO2901-SEC/K9. We have one internet connection (ADSL) current.Now we want to backup internet connection from cable service provider. I will implement IPSec on this HWIC.
What HWIC cards can I choose for this router?
I've been given an 1841 with a 3G HWIC card installed to test with. I need to set up some sort of VPN to our ASA, the problem is though these 3G cards get a random public IP, so what options do I have to create a VPN tunnel from this router to the ASA without the 1841 getting a static public IP?
View 3 Replies View RelatedI'm having problems to ping through interface atm 0/0/0 which is releated to a card HWIC-2SHDSL . The router I have is a 1941. I dont know what to do. [code]
View 8 Replies View RelatedI'm looking for a HWIC card that will support SC fiber connections for a 2811. I know of the HWIC-1GE-SFP but this one only support the LC connections.
View 2 Replies View RelatedWe purchase a new 3945 router and a NM-1A-T3/E3 card. We would like to use the T3 funcationality so we enabled the command card type t3 1 (slot1), reboot the device.After reboot the sh ip int brief command should show the serial interfaces e.g serial1/0.In this case it doesn't, it shows the Gigi interfaces and ATM1/0 no serial interfaces.I've also tried upgrading to the latest IOS from cisco.
View 2 Replies View RelatedI have this card installed onmy 3845 running version 12.4(18). But this card fails to show up.
here is what I found in a show tech.
WIC Slot 0:
Unknown WAN daughter card
WIC module not supported/disabled in this slot
Hardware Revision : 2.0
Top Assy. Part Number : 800-27738-02
Part Number : 73-10677-02
Board Revision : B0
Deviation Number : 0
Fab Version : 02
PCB Serial Number : FOC********
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : HWIC-2FE
Version Identifier : V01
CLEI Code : COUIAFUCAA
Base MAC Address : 001a.6c70.260b
MAC Address block size : 2
Connector Type : 01
EEPROM format version 4
EEPROM contents (hex):(code)
We have Cisco 2811 router with Hwic-3g-HSPA card. When I configure the system everything was fine. Around two weeks 3g interface works, got IP address ,everyting was fine.Yesterday I check the sytem and I saw that cellular interface become reseting itself, without stoping.We have 2 g.shdls and one 3G connection on the same router. dialer 0 ansd dialer 1 for g.shdls, and dilaer 3 for 3G connection. [code]
View 1 Replies View Relatedmy office is looking in ordering a HWIC-1FE to supply our cisco 1841 router with a second ISP connection. i wanted to find out if this card support load balancing and fail over? not sure if fail over is the right terminology so ill explain, i need it so that if one ISP connection goes down (as it does often) it fails over to the second ISP.
View 3 Replies View RelatedCisco 1900 , 2900 and 3900 have Interface Slots and Service Module Slots , My question is which type of card is support this slot.
View 6 Replies View RelatedFrom all of the documentation I am seeing, the 2911 does not support the NM-E3/T3 serial card.
View 16 Replies View RelatedWe're installing a 4G wireless card (EHWIC-4G-LTE-V) in our 2911 for the first time. Upon boot-up, the IOS doesn't recognize the card (the "show inv" command doesn't list it at all). Do I need to give a command or have a certain IOS version in order for it to be recognized?
View 1 Replies View RelatedI have installed a EHWIC-4ESG card into my 2911 router running IOS Ver 15.1(4)M2. When I do a show diag, I can see the card, but I get the following line "Could not get card instance pa_bay=0 slot=0." Am I missing a step, do I have change something, is it not compatible (all that I have read, states that is)
View 3 Replies View RelatedWhat cable I need to connect two 2951 back to back through a HWIC-4T1/E1 card ?
View 1 Replies View RelatedHow I configurate EHWIC-3G-HSPA+7 card on 2911.
View 3 Replies View RelatedI have some LSA type 5, I want to change it from type 5 to type 3 before send to another Area, How can i do it?
View 1 Replies View RelatedWhat is the difference between HWIC-1ADSL-M and HWIC-1ADSL without the "-M"?Can either of the above ADSL cards be used in Cisco 3845 router? We are using HWIC-1ADSL-M in our Cisco 3845 routers everywhere?
View 1 Replies View RelatedI have a Cisco 2811 router with c2800nm-adventerprisek9_sna-mz.124-2.T6.bin as IOS and i wsh to install this HWIC 4port to increase available ports on my router. Wish to know if this is going to work,that is, if i installed it the IOS available will recognise this card
View 4 Replies View RelatedIn our Environmet we have 3845 Edge Router Current Ios Version is Version 12.4(1a),(c3845-advipservicesk9-mz.124-1a.bin)As management got another fiber leased line(Single Mode) for which i have install SFP slot part number HWIC-1GE-SFP,after installation of HWIC-1GE-SFP in router the follwing slot is showing
GigabitEthernet0/1/0
%HWIC_1GE_SFP-6-SFP_IN: Interface GigabitEthernet0/1/0 1000BaseLX SFP has been inserted
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/1/0 xx.xx.xx.xx. YES manual up down
for testing purpose i tried the same procedure into the switch and its working fine where as in Router the link is not coming up ,
meaning slap an HWIC-4ESW into a router, say, an 1841, create an ether channel out of them to connect to my switch?
View 6 Replies View Related